Search Documents

By Donald W. Gentry

This paper presents some of the results of a rock mechanics in¬strumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam and immediately below the coal seam. Longwall test panel 411 had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft). The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) al¬though it ranges from 73-134 m (240 - 440 ft). Roof support at the face was provided by Hemscheidt shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1977

By N. Kuyucak

While Acid Rock Drainage (ARD) occurs naturally, its management poses challenges especially at the decommissioned sites. Two passive systems were designed and implemented at two different decommissioned mining sites in Canada in order to treat the seepage with ARD characteristics. One seep originating from a reclaimed tailings pond was neutral mine drainage (NMD) containing circumneutral pH and dissolved metals (e.g., nickel, zinc) in elevated concentrations. The other ARD from a tailings stack showed net acid drainage characteristics with low pH and higher metal concentrations than regulated limits. Due to the different ARD characteristics occurring at each site, different types of treatment systems were designed and implemented. Both sites experience extreme winter conditions. The NMD has been treated mainly by limestone drain and aerobic systems since 1997. The acid ARD has been treated by a system consisting of an anaerobic sulfate reducing bacteria (SRB) cell, an aerobic cell and a limestone filter since 2004. As this site has no access roads, space, or power, a significant capital cost as well as sludge disposal/storage requirements would have been required to institute a chemical (active) treatment system. Both systems have been successfully treating seepage and producing a water quality year round that could comply with regulated objectives.

Jan 1, 2010

By C. RAMADINI, F. NURJAMAN, A. SHOFI, B. SUHARNO

In this work, the selective reduction of lateritic nickel ore was carried out using sodium sulfate, sodium carbonate, and sodium chloride as additives. The 5 wt% of anthracite coal, which contains 60.35% of fixed carbon and 1.9% of sulfur, was used as a reductant. All raw materials were mixed homogenously prior to the pelletization process into 10–15 mm of diameter. The reduction process was carried out to 50 g of pellets at 950 °C, 1050 °C, and 1150 °C for 60 min in a muffle furnace at atmospheric pressure. It continued with a wet magnetic separation process to separate ferronickel (concentrates) and impurities (tailings). Iron and nickel grade analysis was performed using XRF, while phase transformation and microstructure were analyzed with XRD and SEM–EDS. The results showed that the sodium sulfate was superior, resulting in the highest nickel grade in concentrate, i.e., 15.06%. The sulfidation mechanism, which could inhibit the metallization of iron, effectively increased the nickel grade in concentrate than decomposition of carbonate and chloridization process. The sulfur content in the reductant also influenced the selective reduction process. It promotes more sulfidation of iron, thus increasing the nickel grade in concentrate.

Jul 7, 2021

By Thomas G. Langton

The demand for mineral raw materials, especially in the major industrialized nations, has grown rapidly during the past three decades. One consequence of this growth has been an increasing reliance by the large industrialized countries upon nondomestic mineral supplies. These mineral supplies, to a large extent, have been developed by capital from the major industrialized countries. Until recently, most foreign mining ventures were either wholly-owned subsidiaries or joint ventures between two or more mining companies. The recent rise of economic nationalism has substantially changed the business climate and parameters under which foreign investors operate. This paper describes some of the underlying reasons for this change and notes how investors have adapted to the new business conditions.

Jan 1, 1974

By O. Kangal

Flame retardant materials can be incorporated or applied to products, including plastics and textiles, to increase their resistance to fire. Incorporating a flame retardant in combustible materials and plastics is a common procedure to reduce the risk of fires. Flame retardant applications include interior and exterior woods, structural steel columns, fabrics, open and closed cell foam, pressure treated wood, Formica and all types of fabrics for use in commercial applications as well as residential applications where their fire protection products can save lives and valuables. Huntite and hydromagnesite are amongst the most important flame retardant additives materials. Although various areas of the world have potential huntite and hydromagnesite deposits, their place in industry is not well known, and a detailed field search for their deposits has not yet been conducted. They are active during the starting phase of a fire, in that they prevent the spread of an inner or exterior source of ignition to the flame-retarded material, thereby, preventing, delaying or inhibiting the spread of a fire. Flame-retardants are, therefore, just one element among many in a concept for preventive fire safety. To obtain huntite and hydromagnesite concentrates that are more than 95% pure, which are used in flame retardant industry, flotation tests were conducted on low-quality huntite and hydromagnesite ores.

Jan 1, 2009

By Ximeng Zhu

In the transpassive region, about 0.4 to 0.8 V (SCE), aggressive oxidation of pyrite occurred. The reaction products in this region were Fe(III) oxide, sulfate ion and partially oxidized sulfur intermediates. The growth kinetics of the reaction product film, resulting from transpassive oxidation of pyrite were studied using chronoamperometry measurement with both stationary and rotating disk electrodes. The effect of electrode rotation speed, solution pH and temperature were examined. Potentiostatic measurements were well correlated by a paralinear rate equation, suggesting the formation of an intermediate passive film, associated with the simultaneous dissolution of the outer layer of the film. Activation energies of 66.17 kJ/mole (15.83 kcal/mole) and 38.67 kJ/mole (9.25 kcal/mole) were obtained for associated parabolic and linear rate constants respectively, at an applied potential of 0.6 V.

Jan 1, 1993

By T. E. Bernard

Occupying a refuge alternative (RA) is an accepted practice in mine fires and explosions when escape is not feasible. MSHA has promulgated a final rule on refuge alternatives that includes a recognition that thermal environment is an important consideration. To this end, an environmental index was specified. The question remains about how to test a refuge shelter to demonstrate that it meets the final rule. The analysis followed five activities: A. Provide an estimate of heat generated by an individual refuge alternative occupant; B. Evaluate the Steadman Apparent Temperature criterion of 95°F; C. Discuss simulations based on body temperature or skin temperature limits; D. Suggest method of simulating human heat generation during refuge occupancy; and E. Suggest alternative methodologies/criteria for evaluating heat and humidity survivability inside a refuge alternative.

Feb 27, 2013

By J. D. Ecuyer, L&apos

he microstructure of galvanneal coatings formed on extra low carbon and interstitial free steel substrates has been characterized using electron microscopy (TEM and SEM) and x-ray diffraction. The coatings are found to consist of a mixture of gamma, delta and zeta phases, of which delta is the main constituent. The amounts of each phase influences the powdering resistance of the coating which was evaluated using reverse Olsen testing and 60" bending. For the three heat input conditions considered, IF coatings were always found to contain a significant amount of gamma and only those which retained zeta phase on the surface exhibited a satisfactory powdering resistance. In much the same way, ELC coatings with relatively thick gamma layers performed satisfactorily only when some zeta was retained. It was also found, however, that coatings with minimal zeta and gamma had an excellent powdering resistance. The latter coatings were produced under galvannealing conditions of lower relative heat input. These results indicate that in addition to the zinc bath composition, coating weight and galvanneal thermal cycle, the base steel chemistry also has an effect on the coating microstructure. Knowledge and control of all aspects of galvannealing is therefore essential to consistently produce acceptable coatings.

Jan 1, 1992

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat conduction/ absorption capacity of individual particles, which differs for different species of minerals. When a mixture of fine material is exposed to a radiant energy source, the various solids present in the mixture will absorb heat energy depending on their heat-conducting properties and there will be a difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with a low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler particles will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal, and quartz of 6 × 18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Jan 6, 2022

By Arthur F. Hagner

The titaniferous magnetite deposit at Iron Mountain, Wyoming, is in Precambrian anorthosite. Individual ore bodies are lenses, commonly arranged en echelon, conformable to the platy crystal structure and compositional layering of the anorthosite; a few transect these features at various angles. The ore bodies are on the east flank of the principal anticline in the anorthosite mass. Magnetite and ilmenite, accompanied by spine!, are the ore minerals. The principal gangue minerals are olivine, which was introduced with the ore, and plagioclase, the chief constituent of the anorthosite. The anticlinal region appears to have been a structurally weak zone, and westward-bowing curves of the axis were especially favorable sites for localization of the two largest massive ore bodies. These bodies are synclinal and plunge southeast. The proportion of magnetite-ilmenite to olivine and to anorthosite appears to be related to structural features. Where magnetite-ilmenite is present with olivine, the magnetite-ilmenite is encountered along the most pronounced parts of a fold where anorthite content is highest, whereas olivine is associated principally with more gently folded portions. During granulation and recrystallization of the anorthosite mass, temperature and pressure changes furnished the energy required to release and mobilize iron and other elements that migrated to areas of low pressure, the ore zone. Some iron and magnesium may have combined with silica from partly dissociated plagioclase to form olivine. The ore formed by replacement of anorthosite as indicated by: (1) the marked changes in mineralogy along strike, dip, and plunge of an ore body; (2) the concentration of massive ore in folds and olivine on limbs; ( 3) the halo of low-grade mineralized rock that transects the structure of the anorthosite in the hanging wall; and ( 4) the layering in the large southern ore body, that strikes more easterly than the trend of the body.

Jan 1, 1968

By J. J. Lewis

The chapter describes how several OR techniques assisted the planning of a major new UR project. A computer system was developed to analyze reserves distribution and potential of possible underground layouts, to assist in choosing the location and size of access points. Manpower requirements of each proposed working plan were assessed and matched with the potential recruitment of skilled and unskilled labor. Computer simulations were used to determine the optimum capacity for coal preparation plant and surface bunkerage. For the overall assessment of robustness, financial modelling and risk analysis techniques were adapted to the special requirements of new mines.

Jan 1, 1979

By T. Grounds, K. Singh, W. R. Reed, R. Cross, G. Ross, S. Klima, M. Shahan

"A 2nd generation roof bolter canopy air curtain (CAC) design was tested by National Institute for Occupational Safety and Health (NIOSH) at a Midwestern underground coal mine. During the study, the roof bolter never operated downwind of the continuous miner. Using a combination of personal Data Rams (pDR) and gravimetric samplers, the dust control efficiency of the roof bolter CAC was ascertained. Performance evaluation was determined using three methods: (1) comparing roof bolter operator concentrations underneath the CAC to roof bolter concentrations outside the CAC, (2) comparing roof bolter operator concentrations underneath the CAC to the concentrations at the rear of the bolter, and finally, (3) using the gravimetric data directly underneath the CAC to correct roof bolter operator concentrations underneath the CAC and comparing them to the concentrations at the rear of the bolter. Method 1 dust control efficiencies ranged from -53.9% to 60.4%. Method 2 efficiencies ranged from -150.5% to 52.2%, and Method 3 efficiencies ranged from 40.7% to 91%. Reasons for negative and low dust control efficiencies are provided in this paper and include: incorrect sampling locations, large distance between CAC and operator, and contamination of intake air from line curtain. Low dust concentrations encountered during the testing made it difficult to discern whether differences in concentrations were due to the CAC or due to variances inherent in experimental dust measurement. However, the analyses, especially the Method 3 analysis, show that the CAC can be an effective dust control device. INTRODUCTION Canopy air curtains (CAC) have been shown to be an effective respirable coal mine dust control for roof bolters in a laboratory setting with dust control efficiencies ranging from 14% up to 75% [Goodman and Organiscak 2001, Listak and Beck 2012, Reed et al. 2017]. Unfortunately, there is limited information on their effectiveness for controlling respirable coal mine dust in the field. On continuous miners, CAC dust control efficiencies ranged from 23% to 69% [Krisko 1975]. Two underground tests of the CAC on roof bolters demonstrated dust control efficiencies of 35% and 53% [Listak and Beck 2012] before problems occurred with operation of the CAC. Since the implementation of the new respirable coal mine dust limit from 2.0 mg/m3 to 1.5 mg/m3 (Code of Federal Regulations, 30 CFR 70.100, 2015), roof bolter CACs are becoming more commonplace in underground coal mines as a dust control tool to prevent roof bolter operator overexposure to respirable coal mine dust. J.H. Fletcher & Co. has been instrumental in delivering an effective design which incorporates the filter, blower, and canopy plenum seamlessly into the design of the roof bolter, resulting in a successful operational roof bolter CAC."

Jan 1, 2018

By G. S. Hume

"THERE HAS BEEN a marked growth in the petroleum industry in Canada since the end of the war. The rate of growth in the demand for oil products has exceeded that in United States, although the per capita consumption is still less. Estimates of the consumption of petroleum and petroleum products in Canada in 1951 are approximately 154,000,000 barrels, which is slightly more than 11 •barrels per capita, whereas the estimated consumption in United States for the same period, according to World Petroleum, is placed at 2,619,- 970,000 barrels. This, on the basis of a population of 154,000,000, would be equivalent to 17 barrels per capita. The increase in consumption of the petroleum and products is world wide. World production in 1951 has been estimated (Oil and Gas Journal) at 11,700,000 barrels a day or more than 41;4, billion barrels for the year. United States production increased 13.7 per cent to 6,143,000 •barrels a day and Canada'.s ,, total production increased about 65 per cent from a total of 29,091,235 •barrels in 1950 to an estimated (Dominion Bureau of Statistics) 48,096,800 barrels in 1951.The trend to use increased amounts of petroleum and petroleum products, particularly in the United States and Canada, has also been supplemented by increased use of natural gas. The rate of expansion of the consumption of natural gas in United States in the past few years has been very rapid, increasing from 2,600 billion cubic feet in 1940 to 5,975 billion in 1950, with the proven reserves in the same period increasing from 85,000 billion to 186,000 billion cubic feet."

Jan 1, 1952

By E. V. Leont'eva, V. R. Vafin, A. G. Kladova, N. L. Medyanik, A. P. Ponomarev

"The thermochemical technology for recovery gold, silver from mature flotation tailings of pyrite ores by two-stage sintering with chlorine-ammonium reagents and leaching of bakes with water is developed. The economic effect of the technology implementation is calculated. KEYWORDS Gold and silver recovery, mature flotation tailings, pyrite ores, chlorine-ammonium reagents, leaching INTRODUCTION The relevance of processing the technogenic reserves of ore mining and concentration wastes accumulated over the long operation periods of mineral deposits is beyond doubt. Hundreds of tons of precious and non-ferrous metals that were not recovered during the primary processing are concentrated in the accumulated wastes. For example, tailing storage facilities (TSF) at the mineral processing plants in the Southern Urals region of Russia hold more than one hundred tons of gold and thousands of tons of silver in the mature flotation tailings (MFT) of copper pyrite ores. Secondary processing of technogenic materials is facilitated by the fact that they are preprocessed — ground and compactly deposited on the surface, but complicated by the low (compared to ores) grade, uneven distribution of the valuable minerals, altered and unstable material composition of the mineral feed. This leads to low recovery rates of valuable metals by conventional physicochemical processing methods. It is necessary to develop innovative methods of deep integrated processing of industrial wastes, based on the study of the material composition of specific technogenic mineral resources and based on ensuring the environmental safety of the resulting secondary waste. MATERIALS AND METHODS The object of this study are the MFT of Uchaly Concentrator in the Republic of Bashkortostan, Russia, which processes copper pyrite and copper-zinc ores. According to the data of particle size, chemical, X-ray phase, and optical microscopic analyzes, samples of the MFT are characterized by considerable particle fineness (the fraction of the size class -41 µm is 89-90%), low grade of gold (1.7-2.0 g/t) and silver (18.0-19.5 g/t), comparable grades of iron (23.0-26.8%) and sulfur (28.1-28.7), but different grades of copper (0.12 - 0.73%) and zinc (0.34-1.26%). The most common mineral in the samples is pyrite (50 - 56%), found in intergrowth with grains of other sulfides (0.1-4%) - sphalerite, tennantite, chalcopyrite, covellite. Quartz and aluminosilicates are the dominant rock minerals (21-36%). Based on the results of the phase analysis, it was established that approximately 70% of the gold in the samples is found in a form that is resistant to cyanidation — it is locked in sulfides (52-56%) and quartz and coated by films. Along with sulfides and rock minerals, common gold and silver minerals (chalcogenides, intermetallides, native gold) in the form of submicro- and nano-sized precipitates are also associated with intergrowth of a complex structure. These features of the material composition allow classifying the MFT of the pyrite ores as a mature feed material and emphasize the need for chemical non-cyanide methods to recover gold and silver from the mature minerals and associations they are found in."

Jan 1, 2018

By Ruth Escobar

Así como los seres vivos necesitan del oxígeno para vivir, las empresas mineras precisan de un modelo de innovación exitoso para ser competitivas hoy y en el futuro, esta es la síntesis del trabajo de investigación aplicada que la autora ha desarrollado durante 12 años de dedicada y satisfactoria labor, probando y perfeccionando un modelo de innovación minera denominado Innova, que se basa en la búsqueda de la adición de valor sostenible a una organización, desde la mejora continua de los procesos mineros a la creación de nuevas herramientas y métodos a partir del intraemprendimiento nacido del intelecto e ingenio de sus propios trabajadores a todo nivel.

Sep 30, 2022

By Leslie Burnside

Homestake Mining Co. set out to complete final reclamation at a former open-pit gold mine in west central Nevada. The goal was to exceed regulatory standards by satisfying the company's own high corporate standards for successful reclamation. Homestake's completion requirements challenged available technology due to the unsuitability of heap material as a growth medium, the harsh environmental conditions of the site and the region's lack of native growth medium. Accomplishing these goals required enlisting a multidisciplinary project team to develop, test and implement appropriate and cost-effective revegetation alternatives.

Jan 1, 1999

By N Bianco, D Drinkwater

The professional skills shortage is intensifying, and commentators are predicting a shortfall in supply of qualified professionals for the mining industry, ranging from thousands to tens-of-thousands by 2020 (Tuckwell, 2011; Scoble, 2011; Laurence and Hebblewhite, 2011). Human resources are already stretched, and university graduates arriving in the workplace are often moved rapidly into management positions where there is limited scope to develop their engineering proficiency. This process may well be developing excellent young managers, but our industry is producing fewer excellent young engineers (Munro and Tilyard, 2009). Many believe that it is engineering excellence that is likely to be the key to our industryÆs success in the decade to come. An innovative in-house graduate development program has been created by specialists at the JK Centre in partnership with two mining companies. This program, known as MetSkill«, has been running throughout 2012. Groups of graduates have had to identify a process plant optimisation opportunity and embark on a structured program of data collection and analysis, facilitated by a æteaching teamÆ of researchers and consultants from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. This group project culminates in a report-back session to senior company officials. Along the way, a series of short workshops and other activities provide opportunities to work on specialist skills, and support is also offered by senior technical specialists from the companies involved.This paper outlines key features of the MetSkill« program, along with a report-card on progress in 2012 and plans for further program development in 2013.CITATION:Drinkwater, D and Bianco, N, 2012. Developing minerals industry leaders by encouraging metallurgical excellence, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 287-290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By C. O. Esterhuysen, J. P. Deetlefs, C. A. Wessels

The productivity indices of the Republic of South Africa compare poorly with those of its competitors in the rest of the world. The theory of productivity is relatively simple, and various models are available to demonstrate this. The problem is how to apply the theory in practice and to convert it into a practical management system that will guarantee results. The secret lies in a management approach that aims at a continuous improvement in achievement and that involves the entire work force down to the lowest level in the process. Good management systems ensuring the necessary attention to, among others, management by objectives, finance, personnel, maintenance, planning, and control are a prerequisite for continued improvement and staff involvement. The net result of such an approach is described by the term performance management, which encompasses the total integration of al a company's management systems.

Jan 1, 1989

By A. H. Geisler, F. Keller

Some of the important changes that take lace in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrys-tallization. Although improved metal-lographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based 011 the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mah13-l7 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chcmical or anodic treatment. .After removal from the metal sample by one of the special techniques described by Evans,l9 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,l7 nicke1,7 iron3,8,9 and a nickel-beryllium alloyl1 by heating; films formed on iron8,9 by chemical action; and films formed on aluminum3-'" by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By F. Keller, A. H. Geisler

Some of the important changes that take lace in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrys-tallization. Although improved metal-lographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based 011 the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mah13-l7 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chcmical or anodic treatment. .After removal from the metal sample by one of the special techniques described by Evans,l9 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,l7 nicke1,7 iron3,8,9 and a nickel-beryllium alloyl1 by heating; films formed on iron8,9 by chemical action; and films formed on aluminum3-'" by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944