Search Documents

By J Hadjigeorgiou, T R. Stacey

A ground support system is a combination of individual reinforcement and surface support elements that work together to retain and contain the rock mass. The various elements are subjected to external loads and to interactive loading between individual ground support system components. This paper focuses on the challenges in determining the capacity and behaviour of mesh, recognizing that installed mesh can be subjected to several loading mechanisms. Field observations from underground hard rock mines demonstrate that there are multiple types of damage and modes of failure of mesh. However, these are difficult to reproduce in a laboratory environment. A critical review has shown that existing mesh laboratory testing rigs reproduce very limited loading conditions that may not be representative of underground conditions. This has significant implications in quantifying and extrapolating the performance of mesh to ground conditions. CITATION:Hadjigeorgiou, J and Stacey, T R, 2018. Challenges in determining the capacity of mesh, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 280–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By William G. Pariseau

The purpose of this paper is to present a discussion of the various approaches that can be utilized in the study of mine subsidence phenomena. Attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing the mine. Depending upon a number of factors, the movement of the subsiding rock mass may be such as to disrupt gas and water lines or other buried utilities, to damage surface structures such as buildings and bridges, to dislocate streams, roads, and rail lines, to aggravate acid mine drainage and fire problems, and to generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed.

Jan 1, 1968

By S Lal, S Rost, Q Williams, K Collerson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Shoshonite suite (absarokite-shoshonite-banakite) and adakite-hosted epithermal Au deposits are a feature of circum-Pacific magmatism. Fijian examples include Tavua (Emperor) and Tuvatu on Viti Levu. New discoveries of shoshonite suite and adakite-hosted epithermal Au mineralisation have been made in the southern Yasawa Islands and in central-northern and central-western Viti Levu. The Fijian shoshonites define four NE–SW trending suites. The oldest is the northern 7.9–5.0 Ma Yasawa suite, followed by the 4.7–3.5 Ma Sabeto–Tavua–Rakiraki suite in northern Viti Levu, the 4.7–4.2 Ma Yanuca–Vatulele suite approximately 20 km south of Viti Levu and the 3.4 Ma Astrolabe suite approximately 75 km further south. Shoshonite suite lithologies with 3.8–3.0 Ma ages also occur in the Lomaiviti islands between Vatu-Cake and Moala, to the east of Viti Levu, defining a trend oblique to the NE–SW shoshonite belts. Seatura, a 3.3–2.8 Ma ocean island basalt (OIB) volcano, sits at the northern end of the Lomaiviti trend shoshonites. Trace element/isotopic chemistries indicate that shoshonite arc magma genesis involved the melting of a hydrated supra-subduction zone mantle wedge and also a lower mantle-derived plume (OIB) component. The upwelling plume provided heat for melting and possibly Au enrichment. Accessing the melt generation zone associated with the plume required a slab conduit or window. Such slab windows form by tearing during subduction or occur at slab edges. Adakites form by plume-induced slab melting. The four NE–SW Fijian shoshonite suites are interpreted to occur in back-arc extensional zones above a slab window (tear) that migrated southward during rollback of the New Hebrides–Vanuatu subduction zone. The plume (Seatura OIB) that is interpreted to have caused mantle wedge melting and formation of the Lomaviti trend shoshonites was focused along the interface between the north-dipping Vanuatu–New Hebrides subduction zone and the west-dipping Tonga subduction zone, which we have seismically imaged at approximately 400 km depth. Our model ‘cracks the metallogenetic code’ for shoshonites and adakites and has regional and global implications for Au exploration.CITATION:Collerson, K, Lal, S, Williams, Q and Rost, S, 2015. Cracking the metallogenetic code for Fijian epithermal gold mineralisation , in Proceedings PACRIM 2015 Congress, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By D. B. Mazzinghy, L. C. de R. Machado, H. Delboni, M. G. Bergerman

"The use of vertical stirred mills in the mining industry has increased remarkably over the past few decades, as a result of growing requirement for finer ore grinding. This equipment delivers higher energy efficiency in fine grinding operations when compared to conventional tubular mills. Methods for designing vertical stirred mills involve operational experience, pilot plants and bench tests. An important issue is that these tests require, at a laboratory scale, at least 10–20 kg of material, depending on its density, which is not available in many cases, particularly in the early stages of greenfield projects. For the regrind of flotation concentrates, several bench scale flotation cycles are required to generate such a sample. This paper describes the development of a laboratory jar mill test using a 6”x8” jar – smaller than that commonly used – based on the overall specific energy method, which requires significantly less mass compared with existing tests. The proposed test has proven to be more practical than tests normally used, requiring about a quarter of the mass, and also shows good adherence to industrial results for the studied iron ore processing plant. INTRODUCTION A significant demand for finer grinding has been noticed over the past few decades in several mining projects to achieve the mineral liberation required for the concentration of valuable minerals. However, the finer the product size, the greater the grinding energy consumption, resulting in an overall increase in operating costs, which may reach or even exceed 50% of the mineral processing cost (VIEIRA, PERES, 2013; DANIEL, LEWIS-GREY, 2011). Comminution technology can have a major impact on subsequent ore concentration stages (DANIEL, LEWIS-GREY, 2011; MARSDEN, 2009; NAPIER-MUNN, 2012; PEASE et al., 2010), which further strengthens the importance of proper technology and equipment selection. Adequate grinding circuit selection and design is thus a key aspect associated with mining projects."

Jan 1, 2018

By Willis G. M

Preliminary experiments have shown that, when used in a fusedchloride electrolyte, titanium carbide anodes dissolve yielding lower titanium chlorides which nlay be electrolysed in situ to produce a cathode deposit of pure titanium metal. The anode residues are easily withdrawn from the cell. Further experiments have established the operating conditions for maximum efficiency in the process.The process is essentially two-stage, viz.: (1) titanium carbide production, (2) electrolysis producing metal. Power requirements appear to be moderate and this fact, combine·d with the simplicity of the process make it attractive as a possible method for the production of titanium.INTRODUCTIONDue to the high reactivity of titanium and its, affinity for oxygen and nitrogen, the extraction of this metal generally involves the use of halide. compounds as intermediates. For instance, magnesium reduction of titanium tetrachloride is the basis of the well established Kroll process and electrolysis of the lower chlorides in a molten salt bath has been proposed by Cordner and Worner (1951, p. 358) and others (Brenner and Senderoff, 1952, 223C; The TitaI Company (Inc.), 1952) as means of production of the metal. Thedifficulty of preparation of these compounds prompted a search for an alternative extraction process. The fact that aluminium, an equally reactive metal, has been prepared by electrolysis using aluminium alloy anodes suggested the possibility of a similar process for titanium production.The Titan Company (Inc.) (1952) has patented the use of crude titanium metal anode, but it was thought possible that a metallic compound, such as the carbide, could be used for this purpose. Although Lorenz and Kaufler (1909) suggested the use of carbide anodes for metal production, no...

Jan 1, 1956

By X. Q. Chen

According to the different characters of the middle-low grade bauxite, based on the normal flotation & reverse flotation technology, the author innovates the new technology which is named bi-flotation, it integrates the advantages of normal flotation & reverse flotation, while avoids their disadvantages. Take Henan middle-low grade bauxite as research object, according to the pilot experiment of bi-flotation technology, the concentrate A/S is 9.37 and the recovery of alumina is 80.18% by flotation separate the raw ore which A/S is only 4.19.

Jan 1, 2014

By J. J. Jakosky

"This report is the second of a series dealing with electrical methods of underground communication nd signalling, and is a discussion of some of the factors involved in -applying radio in mines.A previous report2 described the results obtained by the use of the ""T.P.S."" of ground-conduction method of signalling, and outlined in a general way the requirements for a practical mine communication apparatus.The popularity of radio, the development work on new apparatus, a desire to render humanitarian service to entombed miners, and an endeavor to find new uses and applications for radio stimulated many persons to attempt the application of radio to mine rescue purposes. A number of experiments on underground reception from surface broadcast stations have been conducted by different experimenters in various parts of the country and the widespread interest in the subject is shown by the fact that these tests have been con¬ducted in many States, The Bureau of Mines has received information regarding, underground tests in Illinois, Pennsylvania, Arizona, Utah, Idaho, Colorado, Michigan, Wyoming, Kentucky, New York, Connecticut, and in England, Germany, Italy, and Franc.From occasional press notices and illustrations in different papers it may appear that radio communication in mines and in tunnels being excavated is en established fact, and that the method is comparatively simple. As a matter of fact the reverse is the case."

Apr 1, 1924

By H. I. Morrison, A. J. deVilliers, D. T. Wigle, H. Stocker

INTRODUCTION At the end of 1959, high levels of radioactivity attributed to radon and its daughter products were discovered in the fluorspar mines at St. Lawrence, Newfoundland. These levels were presumed to be the cause of an unusually high incidence of lung cancer among the fluorspar miners (deVilliers & Windish, 1964) (Parsons et al. 1964). The mining of fluorspar (calcium fluoride) began in 1933 as open pit operations but converted to standard underground mining procedures in 1936. During the second world war, production was greatly expanded as a result of increased demand for fluorspar used in the production of steel. Wet drilling was first introduced into general use in 1942. Ventilation was mainly by natural draft occasionally supplemented by small blowers. The amount of ventilation varied greatly between mines as well as over time. For example, one large mine, the Iron Springs mine, had only a single small raise to the surface some 600' from the central shaft. Other mines, such as the Director mine, had a number of raises to the surface and, as a result, had far better ventilation. Mines also varied by the amount of ground-water which seeped into them. In the early 1950's, an unusually large number of lung cancer cases were diagnosed among the fluorspar miners. As a result, in 1956 and 1957, J.P. Windish of Canada's Department of Health and Welfare tested for possible causative agents in the mines. Unfortunately, radon measurements were not conducted until 1959 and 1960 when Windish tested Director mine as did the A.D. Little company in 1960. As a result of the high radon levels found, mechanical ventilation was introduced and the concentration of radon dauthers fell, on the average to well below 1 WL. During this period, lung cancer cases continued to be diagnosed with 29 lung cancer deaths recorded by 1964 and 71 by 1971. As of July 1981, 105 lung cancer cases had been identified (Hollywood, 1981). Previous reports concerning the fluorspar miners have dealt in detail with the factors in the occupational environment and discussed occupational mortality patterns. The purpose of this paper is to review further the mortality experience with particular reference to lung cancer in relation to cumulated radiation exposure and to describe briefly our ongoing study of this group. METHODS Occupational histories were prepared for men who had been employed by the mining companies at St. Lawrence during the period 1933 to 1977. The histories were compiled from company records except for the period 1933 to 1936, records for which were lost in a fire; however, the occupational histories for this period were completed by searching census records and interviewing company officials, ex-employees and others. In addition, occupational and smoking histories were also obtained for some miners during a survey conducted in 1978. Occupational records included name and date of birth as well as the type, place and hours of work by year. For each year prior to 1960, hours of work were converted to working months (1 WM = 167 hours) and were multiplied by the estimated average radon daughter concentration in working levels (WL) to yield the annual radiation exposure in working level months (WLM). Pre-1960 radiation levels were estimated on the basis of the history of mining methods employed, ventilation history of the mine, type and place of work and conditions under which the first radiation measurements were made in 1959 and 1960 (deVilliers and Windish, 1964). During the period from 1960 to 1967, the average exposure was about 0.5 WL. Beginning in 1968, radiation levels were measured more frequently, and, beginning in 1969, daily exposures for each worker were recorded based on radiation levels in the place worked on a given day. Mortality data were obtained from medical certificates of death. In a small number of cases, medically certified death certificates were unavailable. In these cases, probable cause of death were obtained from forms completed by the local clergyman (returns of death), parish records, information obtained from interviews with family members of the deceased and/or hospital information, before assigning a cause of death. Data obtained from these sources were found in Tables 1, 2 and 4, cover the time period 1933 to 1971. Data in Table 3 as well as in Figures 1 through 3 cover deaths from 1933 to 1977, and includes only those miners for whom medical certificates of death were available. Two medically certified causes of death were changed from other causes to lung cancer on the basis of pathology reports.

Jan 1, 1981

By B. C. Tripathy, S. K. Padhy, R. K. Paramguru, Pinak Patnaik

"Cobalt is regarded as technology enabling metal among the less abundant metals found in the earth crust. Electrodeposition of the metal from aqueous sulphate solutions is the preferred technology for its commercial production. Certain additives are added in the electrolytic bath during electrodeposition for the production of uniform, smooth and bright deposits of cobalt metal with higher current efficiencies and lower energy consumptions. A detailed investigation has been carried out to determine the effect of additive Sodium octyl sulphate (SOS) on the electrodeposition of cobalt. The results indicated that the additive apart from increasing the current efficiency enhanced the quality of cobalt electrodeposits. A maximum current efficiency of 98.4% was achieved at 10 mg/L SOS. The presence of SOS in the electrolytic bath did not result in any noticeable change in the crystal orientation of the cobalt electrodeposits except at higher concentrations (50 g/L) of the additive. Scanning electron micrographs indicate that smooth, compact and uniform deposits of cobalt were obtained at 10 mg/L of the additive beyond which there is detoriation in the quality of deposits. Polarisation of the cathode was seen in the presence of SOS. The effect of SOS on the electro kinetic parameters: Tafel slope (b), transfer coefficient (a) and exchange current density (I0) has also been investigated.INTRODUCTIONCobalt is recognised to be a strategic metal among the various base metals, owing to its numerous applications in various industries. Cobalt as a metal finds its use in the preparation of rechargeable batteries, as an alloying component in the manufacture of space craft and jet engines, as a drying agent for paint varnishes, ground coats for porcelain enamels and in the manufacture of the catalysts for the petroleum and chemical industries (Davis, 2000). Although there is a huge demand of the metal the supply of the metal is limited due to its scarcity in the earth crust. The metal comprises of only 0.02% of the earth’s crust for which the metal is recovered from various ores of nickel and copper as a byproduct (Hawkins, 1998). The present day techniques for cobalt production includes mostly hydrometallurgical methods which are preferred over the earlier used pryometallurgcial methods carried out for the metal production. Almost 70% of the world’s cobalt produced currently is from hydrometallurgical techniques in which electrodeposition of the metal from aqueous solutions is the final step for metal production (Verney, 1988). The most preferred route for electrodeposition of cobalt metal involves a sulphate medium (Das and Subbaiah, 1984; Lenthall and Bryson, 1997; Sharma et al., 2005)."

Jan 1, 2016

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By Yiming Rong, Gang Wang

"Water quenching is one of common heat treatment processes but with complex physical phenomenon, in which vaporizing, bubbling and convection are involved. The general simulation of liquid quenching processes is conducted by using temperature dependent value of heat transfer coefficient (HTC) obtained from experimental measurement under a strong assumption. A preliminary multiphase flow model developed by using Ansys-CFX for water quenching has been presented in this paper, which shows a distributed HTC with a time dependent feature. The conjugate heat transfer is used to describe thermal conduction in the simplified workpiece, and generation, growth and flow of bubbles are modeled by using Eulerian-Eulerian method for the gas-liquid multiphase flow. The simulation result shows the intense variation of heat exchange through the interface between workpiece and liquid, and the unsteady distribution around the solid surface.IntroductionQuenching is a rapid cooling process which makes the desired solid phase transformations happen for the certain material properties. For aluminum alloy, rapid quenching will prevent all phase transformation and generate a supersaturated single phase."

Jan 1, 2012

An intensive safety campaign at Mount Isa Mines Limited from 1956 to 1966 saw the lost time accident frequency rate fall to half its original level. A review of the safety programme was carried out in 1967 and in 1968 the Five Point Safety System was introduced. The seven years since its introduction have been years of significant achievement both in production and safety. Improving safety is a fundamental part of Mount Isa Mines Limited's policy and this system has been a major tool in implementing that policy. To be successful personnel need to be prepared and trained for its introduction and subsequently counselled on its use. A carefully prepared programme is required to phase in various aspects of the system and to make use of complementary steps. The system has been a success and it is anticipated that the continued drive to improve the use of principles of the system will further improve safety. It is hoped that this paper will be of value to those personnel concerned with industrial safety in Australia.

Jan 1, 1975

By B M. Washington, R R. Lovel, G J. Sparrow, M J. Fisher-White

"Work in CSIRO with several Australian ores has shown that?by heating a high-phosphorus goethitic iron ore and then leaching with caustic or acid, the phosphorus levels in the ore can be lowered to a commercially acceptable value of around 0.08 weight per cent phosphorus (P). With increasing heating temperatures up to 1300¦C, the extent of phosphorus removal increased. This is considered to be associated with mineralogical changes in the iron oxide phases in the ore during the heating.Little phosphorus was removed from four high-phosphorus goethitic iron ores containing 0.12 - 0.16 weight per cent P in leaches with boiling water. However, leaches with sulfuric acid removed ten to 20 weight per cent of the phosphorus and leaching with sodium hydroxide removed even more phosphorus to produce leach products containing between 0.08 and 0.12 weight per cent P from three of the ores.After heating at 300¦C, leaches at a low pulp density of 0.5 weight per cent solids with 1 - 5 M NaOH and 0.1 - 1 M H2SO4 gave leach products with 0.06 - 0.09 weight per cent P. The lixiviant concentration required and extent of phosphorus removal depended on the ore. At a higher pulp density of 25 weight per cent solids, leach residues with between 0.07 - 0.14 weight per cent P were obtained.More phosphorus was removed from ores heated at 900¦C. Leaches at both the low and high pulp densities, with 1 - 5 M NaOH and 0.1 - 1 M H2SO4, gave leach products with 0.05 - 0.09 weight per cent P. However, the lowest phosphorus levels were obtained after heating the ores at 1200 or 1300¦C and leaching with 1 M NaOH or 0.1 M H2SO4. Leach residues with 0.02 - 0.06 weight per cent P were obtained, even from leaches at the higher pulp density of 25 weight per cent solids. Leaching tests on heated samples under heap leaching conditions at ambient temperatures have shown that phosphorus levels can be reduced to similar levels to that achieved in an agitation leach within ten days.CITATION:Fisher-White, M J, Lovel, R R, Sparrow, G J and Washington, B M, 2013. Effect of temperature on removal of phosphorus from Australian Goethitic iron ores, in Proceedings Iron Ore 2013, pp 373-380 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Brent A. Elliott, J. Richard Kyle

Texas is a major producer of industrial mineral resources required by the state’s ever-growing population that now exceeds 28 million. Texas typically ranks in the top three states for the value of non-fuel mineral production with a total value of $5.2 billion in 2017, accounting for 6.9% of the total US mineral value. Almost 90% of current Texas industrial mineral value comes from the production of cement, crushed stone, industrial sand, and construction sand and gravel. Construction material consumption is focused in the 25 metropolitan areas of the state with populations of > 100,000 residents. Industrial mineral consumption is dominated by the four most populous regions of the state—Houston, Dallas-Fort Worth, San Antonio-New Braunfels, and Austin-Round Rock—with an aggregate population of more than 18 million. More than 11,000 employees work in Texas mining and processing operations. Texas produces more crushed stone than any other state from more than 200 quarries; a similar number of operations produce sand and gravel. Specialty industrial sand production for use as proppants in hydraulic fracturing for enhanced petroleum production serves as an excellent example of how developments in one industry sector can markedly affect another industry; the production of industrial sand in Texas has markedly increased over the past decade, reaching $1.3 billion in 2014. With Texas’ population projected to reach 50 million by 2050, continuing in-state development and production of industrial minerals will be required to supply its residential, commercial, and industrial users. Favorable geology and economic factors provide opportunities for identification and development of new industrial mineral production sites.

By E. L. Raymond

The effect of heat treatment on the microstructure and resultant notch-bar rupture life of ZNCONEL alloys X- 750 and 718 was studied. It was found that the primary effect of heat treatment in rendering these alloys notch-ductile is the elimination of any y' denuded zone adjacent to the pain boundaries. The mechanisms by which such a denuded zone can arise and be eliminated by heat treatment are discussed. InCONEL Ni-Cr alloy X-750 and INCONEL Ni-Cr alloy 718 are age-hardenable austenitic materials. Alloy X-750 is used for its corrosion and oxidation resistance and high creep-rupture strength up to 1500°F. Alloy 718 is used most effectively up to 1300°F. One of the most important areas in their development has been establishment of consistently good rupture properties, especially in the presence of a stress concentration, such as imposed by a notch. A desire to improve these properties has led to extensive studies of the effect of heat treatment on the micro structure of these alloys and their performance in stress-rupture tests. In earlier investigations"~ of INCONEL* alloy X-750, *INCONEL i s a Registered Trademark of The International Nickel Co., Inc. grain boundary carbide morphology was linked with stress-rupture properties. If, during heat treatment, the carbide MZSC was precipitated in the grain bound-ary in a cellular form, poor rupture properties re-

Jan 1, 1968

Provide reasonably priced, reliable fire protection for loading shovels. Approach An automatic fire, sensing and suppression system using both dry chemical and Halon 1301 was developed. It is more rugged than similar industrial-type fire protection systems. How It Works Temperature sensors detect heat from a fire, and trigger the system. These sensors are located inside the machinery house and under the house and shovel frame where it rotates around the crawler chassis ring gear. An alarm is sounded, and extinguishing agents are released either in the machinery house or in the ring gear area. The system can also be triggered by a manual control. If the fire Is detected in the machinery house, all power is shut down to the motor-generator sets, ventilation fan, and all electrical controls. Doors are automatically closed. After a delay to allow time for the ventilation fan to stop, Halon 1301, a gaseous fire extinguishing agent, is released inside the machinery house until it reaches a concentration of about 7 percent. This concentration is sufficient to extinguish a fire, but isn't toxic to personnel

Jan 1, 1980

By E. Pourjenaei, P. Ghobadi

High Pressure Grinding Roll (HPGR) is efficient equipment in comminution process. HPGR could be a good option for preparing ball mill feed at the first stage of grinding due to its high efficiency and low energy consumption. Closing with a screen, these mills are utilizing as one of the principle parts in mineral processing industries, especially for iron ores. Recently, HPGRs are working as primary mills at 4 developing lines in Gol-e-Gohar Iron Ore Processing Complex, Iran. Different mechanism of particle crushing in compare to the other tumbling mills makes the HPGR as certain equipment with its own particular controlling parameters. Hydraulic pressure, roller speed and level of material inside feeding hopper are the most important variables influencing grinding efficiency of the HPGR. To figure out how they impress the process and operation situation, different industrial tests were carried out and the best result (d80 about 8 mm for HPGR discharge) was achieved at 180-190 bar pressure (P), 300 rpm speed (S) and 50% of hopper level (L). It is worth noting that this finding has been observed through past pilot test too. We also used design expert method (DX7 software) to develop the best design and analysis the test results, as well. According to the mechanical restriction of HPGR and process limitation in the plant (based on the industrial results), we adjusted value of each parameter in a logical range. Therefore, 20 industrial tests were conducted, as DX7 recommended, and the various impacts of the parameters and their interaction were identified based on statistical analysis. As the authors expected, it was revealed that after presser, roller speed is a critical variable because of its significant role in residence time of the particles between the rollers. The function below has been determined to explain the relation between different parameters and the response.

Jan 1, 2018

By J. Shen

Direct methanol fuel cells have been the subject of considerable research in the last decade. Performance levels realized in cells, stacks, and systems show that this technology is a promising power source for a wide range of portable applications. A direct methanol fuel cell (DMFC) operates directly on a methanol fuel stream typically supplied as a methanol/water vapour or as an aqueous methanol solution in liquid feed DMFCs. The fuel streams in DMFCs are usually recirculated in order to remove carbon dioxide and to re-use the diluent and any unreacted fuel in the depleted fuel stream exiting the DMFC. The concentration of methanol in the fuel circulation loop is an important operating parameter because it determines the electrical performance and efficiency of the direct methanol fuel cell system. The methanol concentration in the circulating fuel stream is usually measured continuously with a suitable sensor, and fresh methanol is admitted in accordance with the signal from the sensor. There are many factors to consider in developing a methanol sensor suitable for DMFCs. These factors include sensitivity, cost, size, simplicity, reliability, longevity, concentration range, and dynamic response. In particular, reliability and low cost should be addressed. Methanol concentration sensors measure methanol concentration by means of detecting the variations of physical/chemical properties of the solution. In this work, methanol concentration sensors based on electrochemistry, electric-capacitance measurement, infrared sensing, ultrasound sensing, and other techniques are reviewed to discuss their advantages and disadvantages.

Jan 1, 2005

By Cliff Holloway

The past year has been difficult for Canada's primary industries. The mining, oil and forestry industries have been hit by low prices and a reduced demand for natural resources. Foreign competition, militant environmentalists, the breakdown of the Asian and European economies and Canada's shrinking dollar have all put additional pressures on the commodity purchaser to buy smarter. It is easy to appreciate why operations and maintenance supervisors want the best performing product. It makes good sense. The challenge is to source that quality product while staying within the budget. The bottom line (price), however, often becomes the control- ling factor, usually at the expense of quality and performance. This is short-term thinking, often with expensive consequences.

Jan 1, 1999