Search Documents

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

By G. L. Zhu, Y. F. Wu, H. Nagaumi

A novel eutectic-type alloy Al12Si-HTC with high thermal conductivity has been developed by strict chemical composition control and heat treatment. The thermal conductivity of the alloy is about 30 % higher than that of current commercial Al12Si alloy. The Al12Si-HTC alloy has a silicon content of 10~12 wt.%, which provides excellent castability. Trace element strontium or calcium is added to modify eutectic silicon, and contents of transition elements such as copper, manganese are controlled in a low level. By appropriate heat treatment, thermal conductivity of the castings increases by 7.5 % and finally reaches 172 W/(m·K). It is found that eutectic silicon modification which makes average particle size finer than 2µm plays a dominant role in improving thermal conductivity, as well as further spheroidization of eutectic silicon and reduction of lattice defects in a-Al microstructure in subsequent heat treatment process. The alloy is successfully applied to produce a certain communication enclosure with complex finned structure by die casting process in industrial scale. The results of numerical simulation and thermal analysis experiments show that when manufactured by Al12Si-HTC alloy, the surface temperature of chips in the enclosure is reduced by 2.0~4.5 ? and the temperature distribution is more homogeneous compared with traditional Al12Si alloy.

Jan 1, 2015

By M. G. Irish, E. E. Vidal, M. J. Jahraus, P. R. Taylor

An experimental system has been designed to monitor on-line variations of leaching parameters in a closed circuit of cyanide leaching solutions and gold bearing ores. Experiments performed to deter-mine variations in some important leaching parameters of the solution: pH, dissolved oxygen, free cyanide, oxidation/reduction potential, gold content, temperature, pressure and solution chemistry. By comparing results obtained when the leaching solution is allowed to become acid or kept basic, it was possible to infer the chemical reactions that occurred between the solution and the ores.

Jan 1, 2004

By K. Prashant Sarswat

Isotopes are critical to a variety of applications including physical science analyses, biology, medicine, pharmaceuticals, and national security. In most cases isotopes must be relatively pure or highly enriched before they become useful. Current isotope separation technologies are relatively inefficient, capital and labor intensive, and often produced by a limited number of suppliers. In the category of isotopes, lithium is among other important candidates. Lithium is found naturally in two isotopes, 6Li which accounts for 7.5% of all lithium, and 7Li which makes up the balance of 92.5%. Each of these isotopes is important to the nuclear industry. 7Li is often used in the form of lithium hydroxide which is used to control pH in pressurized water reactors. The current supply of 7Li is based mostly outside of the United States, and its long-term supply is uncertain. Apart from supply issues, the use of mercury for 7Li separation is also a concern in commercial processing using the most common and efficient approach [1–3]. Hence, a reliable, environmentally friendly, and efficient technique is needed to produce 7Li. In this line of investigations, the authors used a two-compartment system and significant separation was achieved. In this piece of research, some preliminary results are presented including cell design and actual isotope ratio after enrichment. Applying an electro-potential across two electrodes can be used to drive electromigration of Li isotopes. The electromigration is in addition to normal diffusion. Note that 6Li diffuses faster and hence there will be a lowering of the 6Li concentration near the positively charged electrode and an enhancement in 6Li near the negative electrode during the separation process. Similarly, 7Li will be more prevalent near the positive electrode and less prevalent near the negative electrode during the initial separation stage [1].

By A. A. Nourbakhsha

During the last few years, low cement castable refractories found more application in industry, because of good low and high temperature mechanical properties.In the case of alumina based castables ,usually fume silica or reactive alumina are used as superfines in the matrix to form mullite at high temperature which depends to source of alumina . Mullite network formation improves the hot mechanical properties and thermal shock resistance of bodies. The mullitisation of andalusite (so called primary mullite) also produces a certain amount of rich silica glass, part of it being expelled out of the grain. This phenomenon restrict the application of andalusite low cement castable in pig iron ladle. In this research, firstly 8 pig iron ladles from ESC(esfahan Steel company) with different conditions selected and monitored during usage to determine of main factors affecting on corrosion of refractories. Results showed that tap to tap time and undischarged pig iron are the main ones.Therefore monolithic refractories such as castables which increase thermal shock resistance could be substituted. Regarding to ternary phase diagram of Al2O3-SiO2-CaO ,fumed silica was selected as fine particle.After optimization of particle size distribution by using of modified andreasen equation and rehological properties ,different mixture were composed with andalusite ,fume silica, reactive alumina,secar 71 ,SiC and kyanite.All aggregates system components were mixed dry for 1 min in hobart mixer .After water addition wet mixing was continued until getting flowing about 4 min.The ready mixes were poured in the moulds of of 25mm X 25mm X 140mm with vibrations .After demoulding the samples were cured for 24 hrs and dried at 110OC/18hrsand then fired at 1100-1500OC. Physical ,mechanical ,phase analysis(XRD) and microstructure studies (SEM)were carried out according to ASTM standards. Results showed that by addition of kyanite ,more mullite phase formed through the matrix but,because of expansion occured during this phase transformoration, some cracks formed and mechanical properties decreased.By SiC addition the silica film on the surface of SiC lead to improvement of mechanical properties at high temperature

Oct 1, 2011

By Jon R. Maki

"EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer’s pellet silica requirements. In addition, the mine plan was moving towards a lower grade ore and funding was not available for plant improvements to compensate for the change in ore or improving quality. Small changes to optimize various processing equipment resulted in significant improvements in both quality and productivity; for example, productivity on one mill line increased by 10% while producing lower silica concentrate. This paper will provide the methodology that allowed EVTAC to improve quality and productivity through process optimization with little capital investment.INTRODUCTION EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer pellet silica requirements. In addition, the short-term mine plan was changing to a lower ore grade. Because of limited funds, EVTAC did not have the capital for investing in the plant to compensate for the ore change or to make improvements to lower product silica levels. Small changes to optimize process equipment resulted in significant improvements in quality and productivity; for example, one mill line feed rates increased by 10% while also producing a higher quality concentrate. These changes were sufficient enough to allow the mine to lower the target ore grade beyond their initial goal. At one time, a $3M flotation facility was considered as a way to meet quality with the new ore grade. However, the process changes were able to accomplish the same silica reduction with roughly a $50,000 investment in VFDs for sump controls. This paper will discuss some of the modifications that allowed EVTAC to meet the quality and production objectives with little capital investment. It also discusses the methodology used to make these process improvements."

Jan 1, 2014

By R. B. Porter

Bench-scale tests were performed by the Federal Bureau of Mines on lignite and subbituminous coal at pressures to 1,000 p.s.i.g. (pounds per square inch gage) in atmospheres of hydrogen or nitrogen to obtain information concerning the influence of pressure on carbonization of normally noncaking coals. The distribution of gaseous, liquid, and solid products as a function of processing pressure was determined. Except for special experiments, the carbonization was at 940° F. In a hydrogen atmosphere above 400 p.s.i.g., agglomeration of the solid residue (especially with lignite) became noticeable and increased directly with the processing pressure. Although in some instances the solid particles fused together, the mechanical strength of the agglomerate was always low. On the basis of visual inspection, the coals agglomerated in the following order of decreasing intensity: (1) Steam-dried lignite; (2) lignite; and (3) subbituminous coal. Addition of lignite tar in quantities to 25 percent by weight of charge did not increase agglomeration or change the carbonization characteristics of the coal.

Jan 1, 1961

By K. V. Raj, T. Bhowmick

"Control of fugitive dust in high latitude open-pit mines is challenging due to unique atmospheric phenomenon resulting in complicated flow regimes, and atmospheric inversion due to lack of adequate solar insolation during prolonged winter seasons. In this study, two idealized (One conical and one trapezoidal) three-dimensional open-pit mine geometries are simulated for differing seasonal conditions using the CRADLE-CFD package. The airflow is modeled using Standard Kappa-Epsilon Turbulence Model solved by RANS equations. The concept of particle tracking is used to predict the flow pattern of dust particles. For various climatic conditions, and two different pit geometries, fugitive dust particles varying in size (PM0.1 to PM10) and concentration are generated at various locations of a mine and dispersed by the airflow pattern inside the open-pit mine. The amount and location of dust particles inside the pit is reported at various time intervals. The development of atmospheric inversion during the winter season significantly affected the amount of dust retention inside the open-pit domain. While during the summer, airborne dust particles were transported outside the open-pit domain in a short time. INTRODUCTIONComputational fluid dynamics (CFD) modeling of open-pit mines is challenging. In a recent paper, Bhowmick et. al. [1] presented different constraints and challenges in developing a 3-Dimensional CFD model. In order to obtain realistic results from a simulation, however, appropriate values of various inputs are required. Simulation results of a 3D non-hydrostatic model by Shi et al. [2] showed that both the mechanical and thermal forcing are important mechanisms, controlling the development of the atmosphere inside an open-pit. Alvarez et al [3] used a CFD model for predicting dust dispersions in a medium sized limestone quarry, and presented several iso-surfaces of varying dust concentrations using ANSYS CFX. A similar study by Torno et al [4] introduced a more sophisticated parameterization of the dust sources. Flores et al. [5] used an OpenFOAM CFD simulation package to simulate and predict pollutant dispersion in an idealized and an actual open-pit mine in Chile with an intense insolation condition. The model was simulated for three different conditions: (i) air advection (10 m/s) driven mechanical turbulence; (ii) surface heat flux (240 W/m2) driven thermal buoyancy; and (iii) both air advection and surface heat flux driven conditions. The results of the simulations showed that the buoyant currents contribute to the removal of a large percentage of the dust particles. The buoyant currents modify the purely mechanical-turbulence induced flow pattern and reduce the particle residence time, commonly observed in a purely mechanical turbulent flow (non-buoyant case)"

Jan 1, 2015

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of U.S. coal mining companies are beginning to develop coal seams previously thought to be coo deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas contained in coal beds increases with depth, and ventilation requirements are much more stringent for deep underground coal mines than for shallower mines. When the longwall mining method is used at great depths, ventilation, ground control, and operational considerations must all be addressed in the design of longwall panels. This paper examines the influence of these factors, particularly ventilation and operational considerations, upon the feasibility of two, three, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1986

By V A. Maltsev, V I. Panin

The question of prediction and prevention of dynamic events û rock bursts (RB), tectonic rock burst (TRB) and mining-induced earthquakes (MIE), induced by large-scale mining, are discussed. The mine itself and the host geological environment are taken as a natural-technical system (NTS) whose evolution is characterised by alteration of the adaptation-bifurcation (catastrophes) periods. So, to predict TRB-MIE means to predict the limiting NTS states that are determined from the NTS geological monitoring data, and to prevent the said events means to control the processes of rock deformation and failure within the critical zone. The study considers particular examples of how TRB-MIE-events are predicted and prevented in apatite mines, Kola peninsula, Russia.

Jan 1, 2000

By B. Jin

Removal of fluoride and chloride by alkaline washing from direct lead smelting dust which originated from an Ausmelt furnace is reported. The results show that the fluoride removal efficiency increases with an increase of alkaline concentration, alkaline washing temperature and time. The L/S ratio has little effect on fluoride and chloride removal efficiency. A new flow sheet for removal of fluoride and chloride from the dust was successfully proposed according to the results. Fluoride and chloride removal efficiencies are more than 53.68% and 63.18% respectively using the flow sheet under the optimum parameters of temperature 338 K, L/S ratio 3:1 and alkaline washing time of 1.5 h. The contents of fluoride and chloride in the alkaline washing residues can meet the standard of zinc purity as hydrometallurgical materials for zinc processing.

Jan 1, 2014

By Paulo Santiago

Redução dos custos de operação e a produção de aço com menor impacto ambiental são diretrizes unânimes na siderurgia atual. A tecnologia das Turbinas de Recuperação de Topo (Top Recovery Turbines – TRT) é um aliado importante para seguir nessas direções. As TRTs produzem energia elétrica a partir do gás de alta pressão proveniente do topo dos Altos Fornos, gerando energia elétrica sem impacto em emissões. Durante a campanha de operação da turbina, a mesma pode perder eficiência operacional devido a, dentre outros, deposição sobre as palhetas. Com o intuito de melhorar o desempenho da turbina estabilizando sua geração durante toda sua campanha, foi desenvolvido um trabalho de dosagem de polímero dispersante na água de spray da turbina (para turbinas com tecnologia de água de spray na admissão do gás). A dosagem do polímero dispersante visa reduzir a deposição e incrustração nas palhetas, reduzindo assim a perda de performance durante a campanha causadas pelo incremento de massa nas palhetas. Os resultados alcançados em um teste de campo em uma siderúrgica no Brasil foram um incremento de 52% na geração durante a campanha onde o polímero dispersante foi aplicado. Com a aplicação do polímero, uma melhora significativa na confiabilidade e performance da turbina assim como a possibilidade da redução no consumo de água foram atingidos

Oct 30, 2017

By Mattos J. L. C

Drilling and blasting with explosives in mining operations near communities require careful planning to mitigate socio-environmental impacts. Ground vibration, noise emission, flyrock, and dust dispersion are factors that may trigger conflicts with local populations. However, large-scale operations demand high productivity and intense material handling, making it essential to balance operational performance with impact control. The adoption of best practices, combined with advanced monitoring and mitigation technologies, enables sustainable mining even in proximity to inhabited areas. This study proposes the use of double and triple-deck blasting techniques with large-diameter boreholes (12 ¼” – 311 mm), addressing the sizing of charges and decks, as well as measures aimed at reducing noise perceived by nearby communities. The approach seeks to maintain the use of large drilling rigs already present in the operation, avoiding costs related to premature equipment replacement or expensive alternatives, while minimizing environmental and social impacts and promoting a more balanced and responsible mining model.

Jan 26, 2026

By Ann G. Kim, Thomas R. Justin, John F. Miller

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, PA. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic test and subsurface temperatures was not significant.

Jan 1, 1992

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul-road conditions can have a positive impact on mine operations, resulting in heightened safety, productivity gains, longer tire life and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain Mine, monthly site severity studies, ad hoc inspections by frontline supervisors or operator feedback reporting are used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

By E. J. Matson

Under the investigation for critical and strategic minerals the Kaiser mine, formerly the Baxter fluorspar property, in northeastern Mineral County, Nev., was explored. The work comprised excavating 32 trenches averaging 90 feet in length, 8 feet in width, and 1 1/2 feet in depth. The trenches were excavated across the strike of the ore body to enable the engineer to spot the diamond-drill holes; 7 such holes were drilled, aggregating 3,276 linear feet. A total of 20 core samples and 107 sludge samples was taken. The work under this program indicated that the fluorspar southwest of the deposit extended laterally and also at depth at least 250 feet below the 400-foot level. INTRODUCTION The Kaiser fluorspar deposit is in the northeastern portion of Mineral County, Nev. Mining was begun about 1928, and the property has been a consistent producer of both Acid- and Metallurgical-grade fluorspar. The mineralized zone has been developed along a strike length of about 2,000 feet and to a depth of over 700 feet along the dip.

Jan 1, 1957

By J. Drelich, J. Pletka

Lost foam casting patterns are foamed polystyrene shapes glued together into the shape of the part to be cast and are coated with a refractory material consisting of a mineral mixture and binders. Prior to casting, a significant number of the patterns are damaged and inevitably land-filled. In this study, a process is developed for the recovery of foamed polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and density separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene.

Jan 1, 2001

By R. H. Atkinson, R. N. Rhoda

An improved technique has been developed for the deoxidation of palladium with aluminum which is especially suitable for use in making small castings with an induction-melting and casting machine. The effect of various crucible linings on the efficiency of the residual deoxidizer and accompanying oxide film in protecting palladium against oxidation during remelting also has been examined; the preferred crucible lining consists of zirconia cement. THE objective of this work was to develop a simple method of deoxidizing induction-melted palladium which would be suitable for use by manufacturers of jewelry and other small castings. In a common method of deoxidizing torch-melted palladium a piece of aluminum foil is dropped on the surface of the molten metal. If a film is present, which is usually the case, it must first be removed by oxidizing the molten metal thoroughly because it would interfere with the entry of the aluminum into the melt. Removal of the film is probably facilitated by a mild fluxing action of the silica crucibles which are used for torch-melting. However, removal of an alumina film from molten palladium in the crucibles normally used for induction melting is a much slower process and it became necessary to modify the de-oxidation procedure. In the modified procedure the charge is simply melted and the desired amount of aluminum, crimped to one end of a tungsten wire, is plunged through the film into the palladium and the wire immediately withdrawn. The trace of tungsten which dissolves along with the aluminum can be avoided, if considered objectionable, by using a palladium wire. In view of the persistence of the alumina film under the conditions of induction-melting it also was decided to ascertain the efficiency of this film in protecting palladium against oxidation during repeated remelting and casting. Melting Equipment and Materials The equipment used for melting and casting consisted of an Ecco GC:6, 6 to 8-kva high-frequency converter and an Ecco M34B centrifugal casting machine. This unit is being increasingly used for making jewelry and dental castings and it also has been found useful in making exploratory melts of a variety of nickel alloys, for which purpose it is well suited on account of its speed of melting and economy of material. A description of the machine and its operation will be published elsewhere.' A common palladium jewelry alloy, 95.5 palladi-um-4.5 ruthenium (referred to as "palladium" in the trade), was selected for the deoxidation tests. It was available as melting stock which had been melted in air to free it from oxidizable impurities, and also as clean scrap from previous melts which had been deoxidized with aluminum. The latter was thought to be typical of clean "palladium" scrap to be found in a manufacturing jeweler's establishment and it is also similar to one brand of "casting palladium." By the same token, the oxidized melting stock corresponds to "casting palladium" after the latter has been melted and thoroughly oxidized: Pure aluminum wire (99.9 pet), 0.032 in. diam; 1 in. = 0.036 g. Scrap tungsten wire, 0.014 to 0.020 in. diam. Argon, commercial water-pumped; 99.9 pet pure Experimental Procedure Samples of about 50 to 75 g of the palladium alloy were melted in a crucible lined with a proprietary refractory alumina cement. Some charges were melted in air, others in argon. The oxidized melting stock was melted and solidified a number of times in order to remove as much oxygen as possible before deoxidizing, but this treatment was unnecessary in the case of scrap. In either case the metal was deoxidized with aluminum (0.01 to 0.05 pet) by the

Jan 1, 1959

By D. François-Bongareon

"In previous publications by the author, significant advances and generalizations of the theory of sampling of broken ores, prompted and confirmed by experimental results, have been presented. This paper shows how to implement these theoretical results in practice. The models to be used are reviewed, with a description of the various sampling parameters involved. Then the methodology for the experimental assessment of those parameters, including segregation factors, is described in simple and practical terms, along with the use of handy sampling protocol charts. Finally, the particularly important case of processing data from a sample-tree experiment is detailed, and examples of applications covering all situations and types of experiments are provided.IntroductionThe reliability of a sample of crushed material , i.e. the expected (average) deviation between its true grade and the true grade of the lot it comes from, mostly depends upon six factors:• the size (mass) of the sample (and to a minor extent, for small lots, the size of the lot);• the size of the rock particles (degree of comminution)• the nature of the mineralization at microscopic scale (i.e., within even the smallest particles);• the geological nature of the mineralization and mineral of interest;• the grade of the lot in the mineral of interest; and• in some cases, the state of segregation of the lot.In practice, one should first disregard segregation problems, and assess sample variability in the segregation-free case. Once the numerical parameters governing this variability have been assessed, then segregation factors can be assessed in turn. In the case of laboratory standard sample preparation procedures, segregation can usually be disregarded altogether."

Jan 1, 1993

By R H DAVIES

Peak Gold Mine is a new gold and base metal mining project being developed by Enterprise Metals (a 100 per cent subsidiary of CRA) at Cobar in the centre of New South Wales. The Cobar district has a long history of copper and gold mining operations stretching back to the 1870s. Extensive gold and base metal mineralisation was discovered at the Peak in 1981 below a series of gold mines which had been active around the turn of the century. Evaluation of the deposit through the 1980s led to CRA's decision to develop the project for production at a capacity of 450 000 tonnes per annum in late 1992. The project has been developed with a green fields approach despite the long history of mining in the local area. This approach has lead to several innovative ideas being trialed at the site which are expected to result in the operation being a low cost producer of gold and base metals.

Jan 1, 1992