Search Documents

By Walter D. Holland

This study was undertaken to determine miners' breathing zone concentrations of diesel exhaust components, to investigate any relationships between these concentrations and vehicle type, the presence of emission controls, vehicle usage, and ventilation conditions, and to make recommendations for monitoring and ventilation requirements. Twenty-four mines including two con l mines were surveyed. Sampling was done for CON, NON, SOx, PNA, aldehydes, and particulates. hi most mines, concentrations of at least one contaminant exceeded one half the standard or TLV. The concentrations of gases arc probably sufficiently reduced by a minimum air velocity of 50 fpm. A sufficient reduction of particulate concentrations may require as high as 400 fpm air velocity. Vehicle age, type, or usage appear to have little or no effect on contaminant concentrations. PNA levels were below detection limits in all but a very few samples. Minimum requirements for routine monitoring should include formaldehyde, COx, NO2. It is further recommended that better definition of the minimum ventilation requirement be obtained.

Jan 1, 1978

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"The ever increasing number of automobiles and the consequential increase in consumption of tires have generated a pressing environmental issue, concerning the disposal of unserviceable tires. The worldwide disposed of waste tires is approximately 1 billion units per year and this amount is expected to increase by 2% each year. This work presents a microstructural characterization of nanomaterials synthesized in a catalyst system from the effluent of burning waste tire chips in a horizontal two-stage laminar-flow furnace. Controlled combustion of waste tire chips took place at temperatures of 900 or 1000 °C, and stainless steel meshes were used to synthesize the nanomaterials at 1000°C. Produced materials were analyzed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The catalyst meshes were covered by materials with diameters of 20 to 200 nm and lengths of about 40 µm. They possessed structures similar to those of carbon nanotubes.IntroductionThe motor vehicles on the road have been increasing annually. World motor vehicle production in 2009 approached 62 million units. Consequently, the consumption of tires has also been on the rise; about 1.4 billion units were produced around the world in 2007 [l]. The disposal of scrap tires is a serious environmental problem. The worldwide disposed of waste tires is almost 1 billion units per year with an expected increase of around 2% each year. However, less than 7% of produced waste tires are recycled (excluding reuse, retreading or incineration). The waste rubber tires are a thermoset polymer, which cannot be reprocessed like thermoplastics polymers, therefore the recycling of this material requires special techniques that demand big investments [2, 3].A solution to the disposal of waste tires is the sequential pyrolysis/combustion process. Past research showed that waste tires are an attractive potential fuel due the high heating value (29-3 7 MJ/kg), which is comparable, or even higher to those of typical bituminous coals [ 4, 5]. Pyrolysis is a process wherein the material is thermally decomposed at elevated temperatures at the absence of an oxidizing gas. Combustion is characterized by the addition of the oxidizing gases during the process. Several studies indicate that the pyrolysis and combustion processes for the tires treatment have a great energy conversion potential [4, 5, 6]."

Jan 1, 2011

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

By Albert Hill Fay

IN giving a sketch of the geology and mining of the tin-deposits of Cape Prince of Wales, a short description of the geographic and climatic conditions may be of special interest on account of this being a part of the world of which very little is known, even by the reading public. As shown in Fig. 1, the location of the Cape is lat. N. 65° 35' and long. W. 168°. It is bounded on the north by the Arctic ocean ; on the west by Bering strait and on the south by Bering sea. It is the western-most point of the mainland of North America, and to the west, across the strait, one can see East Cape, Siberia, which consists of a rugged, steep coast of granite cliffs. The climatic conditions are of interest because of the part they have had in the surface geology, and also because they affect mining from an economic standpoint. In connection with the climate and geography, it does not seem out of place here to quote a few lines from the prologue of The Wandering Jew, written by Eugene Sue, under the caption '1 The Land's End of Two Worlds."

Sep 1, 1907

By H. Sevim

Three transportation systems in surface coal mines: 1-Truck Haulage, 2-Belt Conveying, and 3-Coarse-Coal Slurry Transportation are compared from the operations and cost point of Views. Computerized design and cost models were developed and cost data banks were compiled for each system. These models can be used to evaluate transportation systems and layouts that are practiced in most of the U.S. surface coal mines. A typical midwestern area strip mine was considered for illustration purposes. Sensitivity analysis on critical parameters such as production rate, transportation, distance, etc. was conducted and the outcomes are presented.

Jan 1, 1990

By H. W. Byerlee

A contactor has been designed that avoids solvent loss due to coalescence and other causes. This consists of a column packed with grids. Slurry enters at the top and flows as films down the inclined surfaces of the grids. The solvent, which fills the column, flows counter currently to the slurry. Tests on, and modifications to the contactor are described. '

Jan 1, 1982

By J. R. Bell, W. J. Childs, J. H. Bucher, G. A. Wilber

A technique for determining recrystallization times as short as 0.10 sec was developed utilizing the "Gleeble", a commercially available testing system designed for the study of short-time, high-temperaLure themal and mechanical processes. The procedure consisted of heating a small tensile specimen to a given temperature of hot deformation, loading to a given reduction in area, unloading, delaying various intervals at temperature, and then reloading- to failure. The magnitude of the ultimate load obtained upon reloading decreased with delay lime as recrys-lallization proceeded. The technique was applied to austenite recrystallization in AISI 1010 and AISI 1010 uith 0.02 pct Cb steels. For each steel the reduction in area given the specimen on the first pull was mainlairred at 30 ± 5 pct and recrystallization times deterntined at various temperatures. The results indicaled a significantly slower rate of recrystallization for the columbium-modified composition, suggested the presence of- a recovery stage in the softening process , and indicated a greatly increased softening rate at a temperatuve where significant allotropic transformation to a partially ferritic Structure could occur. In recent years increasing attention has been paid to the fact that the process of recrystallization of austenite deformed at elevated temperatures is far from instantaneous at many practical hot-working temperatures.1-3 This realization has given rise to such terms as hot cold-working1 or warm-working,2 These terms generally describe processes where the recrystallization rate at the temperature of deformation is slow enough to have an appreciable effect on mechanical properties despite a relatively high deformation ternperature. The mechanical properties of interest can be either the properties at the deformation temperature as in hot-workability studies4 or the room-temperature properties after cooling as in the many recent studies of various thermomechanical processes172 where heat treatment and deformation are intentionally combined to give a unique set of room-temperature properties. Because of this interest in processes where the austenite recrystallization kinetics can be an important variable, the development of quantitative methods of following the course of short-time, high-temperature recrystallization has received increasing attention.l,3,5 The experimental methods to date have, in general, relied upon rapidly deforming the austenite, holding at temperature for various brief intervals, quenching as G.A.WILBER and W. J. CHILDS, Members AIME,are Research-Fellow and Professor, respectively, Rensselaer Polytechnic Institute, Troy, N. Y. J. R. BELL and J. H. BUCHER, Member AIME, are Research Engineer and Research Supervisor, respectively, Graham Research Laboratory, Jones & Laughlin Steel Co., Pittsburgh, Pa. Manuscript submitted March 13, 1968. IMD. rapidly as possible, and then using room-temperature measurements to follow the recrystallization process. Although such methods can be successfully applied to certain alloy steels, the existence of the allotropic transformation during cooling of plain-carbon or low-alloy steels tends to obscure the results. Thus, such room-temperature measurements as hardness and X-ray line widths do not correlate well with the extent of austenite recrystallization before quenching,5 and results based on room-temperature microstruc-tural observations are dependent upon the success in correlating the observed structure with the prior aus-tenitic grain structure.1,3,5 The purpose of the present work was to develop a quantitative method for the determination of short-time, high-temperature recrystallization rates, based on measurements made at the temperature of deformation. EXPERIMENTAL TECHNIQUE The basic technique consisted of heating a small tensile specimen to a given temperature of hot deformation, loading to a given reduction in area, unloading, delaying various intervals at temperature, and then reloading to failure. The data were obtained in the form of traces of load and elongation as a function of time. Due to the high deformation temperature, the strain hardening introduced during initial loading was progressively annealed out with holding time after unloading and the loads obtained upon reloading decreased as this softening proceeded. Although the value of the second load at any Consistent point On the load-elongation curve could have been used as a measure of the degree of softening, the most convenient to use was the ultimate load. The softening indicated by the decrease in the second ultimate load with time is essentially a process of annealing of cold-worked material at a high deformation temperature. Although some recovery grain growth may contribute to such a softening process, it is generally considered that the major softening which must take place to achieve complete removal of substantial Strain hardening will occur by the formation of new, stress-free grains. As the results of this work indicate that essentially complete removal of strain hardening did in fact occur. the primary softening process will be attributed to recrystallization, and specific reference made where it appears that other mechanisms may be contributing to the total observed softening. It would, of course, be of interest to attempt to correlate the results of this work with the actual austenite fraction recrystallized as determined by other techniques. This was not attempted in the present work because it would have required running a large number of additional specimens and, as discussed previously, there is limited assurance that the results would accurately reflect the prior austenite fraction recrys-

Jan 1, 1969

By K. Moriyamo

Operation improvement efforts at Hyuga Smelting Co., Ltd. have focused on calcining capacity in the reduction rotary kilns ("the kilns"), whose limited feed rate capacity had capped production at around 18,000t-NiN since 1995. To improve the kilns' feed rate capacity of 80 wet t/hr, attempts were made to increase the gas flow in the kilns by increasing the capacity of the off-gas fans. However, as the increased gas flow resulted in only limited improvement of the kilns' feed rate, a scoop feeder was installed on each kiln to add coal to the middle of each kiln's interior to gain a higher efficiency of thermal supply and conversion. With these gas flow and coal charge addition operations, the kilns' feed rate capacity increased up to 120 wet t/hr, with burner fuel efficiency increasing by approx. 10% (approx. 5% in total with the additional coal included). As a result, production was raised to a level of 22.000t-Ni/Y Keywords: reduction rotary kiln, scoop feeder, additional coal charge.

Jan 1, 2004

By H. Evans, L. A. Hunt

The raw materials used in the blast furnaces at the Geneva Works of U.S. Steel Corp. have a high degree of variability in size-consist and chemical content. To overcome the problems caused by the use of highly variable raw materials in the blast-furnace operation, large blending piles are used. An investigation of the blending system showed that variability was significantly reduced by the use of these blending piles. This paper describes the blending system, the method used to evaluate the effect of the blending system, and the results of the investigation. The remarkable improvement in blast-furnace performance since World War II has been in large measure due to the use of beneficiated burdens to reduce the variation of both chemical analysis and size consist. This practice allows the operator better control of his blast furnace, enabling him to operate more economically and to produce chemically uniform hot metal. Planning for uniformity usually begins during mining by extracting ore from several locations within a pit to produce a final product with a specified analysis. Another approach is to stockpile ores having widely varying analyses in individual piles and then drawing the required amounts from each stockpile to provide a blend with a predetermined analysis. A further improvement in blending procedures is to take ores from several sources, bedding them horizontally in layers and reclaiming by vertical slicing from the blended pile. The last procedure, when properly executed, is one of the best methods for achieving maximum uniformity with highly variable ores. U.S. Steel Corp.'s Geneva Works initially obtained iron ore for their blast furnaces from the Cedar City area of southern Utah. These ores were formed primarily by the replacement of limestone and siltstone formations with solutions containing iron and several other elements. The original iron content of the ores in the ground varied from a high of 70% to practically zero with a minimum acceptable iron content for shipping of 37%. Substantial amounts of silica, calcium, magnesium and alumina were found in the ores along with minor amounts of copper, lead, zinc, nickel, titanium, manganese, phosphorus and sulfur which were sometimes present in detrimental amounts. Iron-to-silica ratios varied considerably throughout

Jan 1, 1968

By G. E. Slagel

On August 3, 1987, a hearing was held by the House Subcommittee on Energy and the Environment to commemorate the tenth anniversary of the Surface Mining Control and Reclamation Act (SMCRA). Four panels of environmental/citizen group representatives went before the Subcommittee to report on the state of affairs (from their perspective) of the coal industry and the Office of Surface Mining, Reclamation and Enforcement (OSMRE) As expected, these groups had little positive news to report and continued to focus on glaring deficiencies within the surface mining program. They indicated that gross abuse of SMCRA has continued over the past ten years and the states have performed poorly. Congressman Udall's opening comments perhaps best characterized the mood of the group with his statement that "The Act has not accomplished what I or the people of the coalfields had hoped." and " ? a segment of the coal industry has continued in its bitter and implacable opposition to the most basic of environmental controls."

Jan 1, 1988

By G. E. McClelland

The Bureau of Mines investigated chemical methods for producing high- purity gold from precious-metal-bearing zinc precipitates and steel wool cathodes. Precious-metal-bearing zinc precipitates and steel wool cathodes are unrefined products from conventional cyanidation and heap leaching-cyanidation operations. The zinc precipitates contained 14,40 pct Au and 0.35 pct Ag. The precious-metal-bearing steel wool cathodes contained 20.65 pct Au and 4.84 pct Ag. The precipitates and cathodes were treated with dilute acid to solubilize the silver and/or base metals. The gold-bearing residue was leached in dilute aqua reqia to solubilize the gold. High-purity gold was precipitated from the aqua regia solution with oxalic acid, sulfurous acid, sodium bisulfite, and gaseous sulfur dioxide. The leaching-precipitation experiments recovered 99.9 pct of the gold. The gold precipitates ranged in fineness from 997 to 999 fine. The chemical refining method provides a viable technique for the smaller operator to produce high-purity gold without using pyrometallurgical refining methods.

Jan 1, 1985

By D Connelly

Magnetite ores can be used to produce very high-grade concentrates that are suitable feed for the direct reduction process route but the high sulfur content of some concentrates can cause substantial environmental issues. Processing of high sulfur magnetite ore is therefore increasingly problematic for the industry. Generally, the industry demands a concentrate with <0.05 per cent sulfur and <2 per cent silica. This paper reports the outcomes of a study to produce a concentrate with the requisite low sulfur content from a sulfur-rich magnetite ore. The main findings may be summarised as follows: if the sulfur is present in magnetite as nonmagnetic pyrrhotite or pyrite, it can be beneficiated using magnetic separation and hence, monoclinic pyrrhotite is magnetic and is magnetically recovered with magnetite leading to a concentrate that is too high in sulfur. X-ray diffraction and QEMSCAN analyses revealed that the magnetite concentrate was liberated at P80 30 microns and was associated with maghemite, pyrrhotite (magnetic), carbonates and hematite with very low amounts of chalcopyrite, sphalerite and arsenopyrite. Sulfur removal using flotation was the first stage of investigation and this required flash flotation in the grinding stage followed by column flotation of the initial concentrate to generate the final concentrate. At the same time, it was observed that oxidation of the pyrrhotite had a negative effect on its flotation requiring copper sulfate to activate it. Bioleaching and concentrate leaching were also considered and achieved over 90 per cent sulfur removal but were deemed unsuitable owing to the production of highly reactive wastes and high CAPEX. Reference is made to a number of operating magnetite producers and how they manage the sulfur in feed.

Sep 18, 2023

By Amitava Gangulee, Michael B. Bever

The effects of changes in short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions have been investigated. The heats of formation at 273°K of several alloys after two different thermal treatments were measured by liquid metal solution calorimetry. Their electrical resistivities were measured at temperatures ranging from 4° to 773°k. Tensile tests and microhard-ness measurements were carried out at room temperature. An effective short-range order parameter and an effective interaction energy are defined. The measured changes in the properties are interpreted in terms of these quantities. The short-range order parameter is evaluated separately from calorimetric and X-ray data; the results are in fair agreement. Increasing short-range order lowers the resistivity of- the silver-rich Ag-Mg alloys but does not measurably affect the temperature dependence of the resistivity. Short-range order increases the yield stress of these alloys but does not affect the ultimate tensile stress. Changes in the effective short-range order parameter independently obtained from measured changes in the heat of formation, resistivity, and yield stress are in fair agreement. THE thermodynamic, electrical, and mechanical properties of solid solutions have been investigated as functions of composition in many alloy systems, but the effects of configurational variables, such as short-range or long-range order, on these properties have received much less attention. The silver-rich terminal solid solutions in the system Ag-Mg are well-suited for the investigation of the effects of order. The composition of these solid solutions may be varied over a range extending to about 27 at. pct Mg.1 Appreciable short-range ordering is likely to take place in these solid solutions; the degree of short-range order can be varied by suitable thermal treatments. In the alloy Ag3Mg long-range ordering is possible.2 This paper is primarily concerned with the effects of short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions.-The long-range ordering transition is the subject of a concurrent paper.3 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Ag-Mg alloys containing up to 26.4 at. pct Mg were prepared by melting 99.99 pct pure Ag (obtained from Baker Chemical Co.) and 99.99 pct pure Mg (obtained from Eastman Chemi- cal Co. or Johnson Mathey & Co.) in graphite crucibles under molten potassium chloride. The solidified ingots were homogenized at 823°K for 10 days in evacuated Vycor capsules. A surface layer 6 in. thick was then removed by machining. The ingots were swaged into rods (2.5 mm diam) which were drawn into wires (1.0 mm diam). The wire specimens were annealed at 773°K for 24 hr in vacuum and either quenched into iced brine or cooled to room temperature over a period of 15 days. The average grain diameter (obtained from the linear intercepts) was about 0.1 mm. 1.2) Calorimetry. The heats of formation of the alloys were measured in a tin solution calorimeter as the difference in the heat effects of alternate additions of samples of an alloy and the mechanical mixture of its component elements. The additions were made from 273°K to the bath at about 623°K. The heat effect on addition of the alloys was approximately 5.5 kcal per g-atom. The procedure and the method of calculation have been described.4 1.3) X-Ray Diffraction. Short-range order parameters of two alloys were calculated from diffuse scattering intensities,&apos; obtained with briquettes made from powdered specimens. A GE-XRD 5 diffractometer with filtered copper radiation was used. The absolute intensities were based on calibrations with paraffin. 1.4) Resistivity Measurements. The electrical resistivities were measured by a potentiometric method in which the potential drop across the specimen was compared with that across a standard resistance. For measurements below room temperature, the specimens were immersed in liquid helium (4°K), liquid nitrogen (78°K), dry ice and trichloroethylene (195°K), or ice and water (273°K). Measurements above room temperature were made on specimens held in a furnace under helium or in vacuum. The resistivity measurements were reproducible to ±0.5 pct or less. 1.5) Mechanical Tests. Tensile tests were carried out at room temperature with a Tinius-Olsen XY elec-tromatic Universal testing machine. Wire specimens (nominal gage length 1 in.) were used. The strain was measured with an extensometer, which had a sensitivity of 4 x 10-5; the strain rate was 10-3 min-1. Microhard-ness measurements were made with a square-pyramid indenter and a 100-g load.11 2) RESULTS AND DISCUSSION All measurements were made on two parallel sets of specimens, one quenched and the other slowly cooled from 773°K. The reported values are the averages of at least three measurements. In the range of magnesium concentration substantially below that of the composition Ag3Mg, quenched alloys have less short-range order than slowly cooled alloys. As the magnesium concentration approaches that of Ag3Mg, slow cooling develops long-range order. Quenching sup-

Jan 1, 1969

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat, A. J. S. (Sam) Spearing

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. Initially, ASTM A615 grade 60 steel roof bolts, which are the most commonly used bolt material in the United States, were tested with and without stresses in a simulated underground coal-mining environment for approximately six months. This paper mainly discusses the test system, protocol and system shortcomings, and makes recommendations based on the observations and results.

By Saurabh Kundu, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Manikanta Nallamilli, Shaik Mahaboob Basha, Neha Gupta, Srinivas Dwarapudi, Dhiraj Madhukar Kadhe

Iron ore pelletizing using compressive and shear action on wet mixture feed has been studied. The physical properties, namely, moisture content, drop strength, green compressive strength (GCS), dry compressive strength (DCS), porosity, and cold crushing strength (CCS), have been studied. Pelletizing tests were carried out on four different types of ore, namely, hematite ore, magnetite ore, goethite ore, and sinter return fines. The inference of shear forces on silica distribution index in dry pellet has been studied using optical and scanning electron microscopy. Significant improvement in physical strength was observed due to compressive and shear forces on the pellet mixture feed. However, decrease in moisture content and ball porosity has been observed. Silica distribution index improved by 1.72 times for hematite ore, 1.47 times for magnetite ore, and 1.68 times for goethite ore. It has been found that bubble cavity has been reduced which is good indicator in terms of physical properties.

Jan 29, 2022

By Thomas V. Falkie, R. Venkataramani

Underground coal winning operations can broadly be classified as conventional, continuous, and longwall mining. In conventional mining, the operations of cutting, drilling, blasting, loading and hauling, and roof support are performed in that sequence in each working face in a work area. The major difference between continuous and conventional mining is that the coal is cut and loaded by a continuous miner in the former, thereby combining the unit operations of cutting, drilling, shooting, and loading into one. Longwall applications have been viewed with great interest in recent years, and although at the end of 1970 there were only 37 longwall installations in the U. S. with combined production of less than 4 percent of underground total, there is no question about the growth potential of longwall in the United States. Increased capacity, versatility, and power characterize continuous miners today. Although continuous miners have outsold conventional gathering-arm type loading machines for some years, the latter, in the new extra-high capacity types, are continuing to find wide use. Whether the mining system is continuous or conventional, the haulage units may include six-wheel articulated shuttle cars, tractor-trailer units, or extensible belt and bridge-conveyor systems, all tending to increase the productivity of the face units. The decision as to which to choose - continuous or conventional mining - is complicated, and both systems are capable of high production rates. Most continuous miners in use today have a revolving pick-mounted drum to cut the coal and a gathering arm loading unit. Functionally, there is little difference between the loading unit in a

Sep 1, 1972

By D. A. O'Keefe, M. M. Wong

To obtain beryllium metal of higher purity , flakes produced from electrorefining scrap metal were used as cell feed for a second cycle of electrore fining at 500 ° C in an electrolyte composed of 51.7 mole - percent LiCl , 36.9 molepercent KC1 , and 11.4 mole - percent BeC¹ · Metallic impurities in the flakes totaled more than 108 ppm , the metallic impurities in the metal obtained from the two - cycle electrorefining were , with the exception of 35 ppm of calcium , below the spectrographic determination limits .

Jan 1, 1964

By Max Y. Seaton

THE scope of this paper will be limited to finished materials that contain a large preponderance (around 80 per cent or more) of magnesium oxide. The large and commercially important production of refractory dolomite and modified dolomites is not discussed here, and the production of magnesium basic carbonate for use as a heat insulator is barely mentioned. The discussion is confined mainly to magnesias produced in comparatively great quantity by direct processing of naturally occurring raw materials and hence excludes secondary or highly purified products such as pharmaceutical products or U.S.P. light and heavy calcined magnesias of commerce. NOMENCLATURE The nomenclature of the magnesia products that will be discussed is somewhat confusing, in that it is customary in the trade to designate as "calcined magnesite" the materials that result from the calcining of magnesite to temperatures that remove the contained carbon dioxide. The finished product, therefore, is not magnesite at all but simply a more or less pure magnesium oxide or magnesia. Furthermore, partly for statistical and partly for commercial reasons, it has been customary, during recent years, to classify as "calcined magnesite" products that result from the heat-treatment of magnesium hydroxide precipitated from magnesium-containing brines; products that, obviously, have no relationship whatever to magnesite. In the listing of magnesia-containing materials, tonnages of which are regularly reported by the Bureau of Mines, reports ordinarily are made under two headings: "caustic calcined" magnesite, in which all of the varieties of products treated at relatively low temperatures are lumped; and "dead-burned" magnesite, in which are included both high-purity and low-purity, and particularly both high-iron and low-iron, materials that have been so heat-treated that the magnesium oxide occurs predominantly as crystalline periclase-materials used almost entirely for refractory purposes. In 1940 the apparent domestic consumption of "caustic calcined" magnesite was approximately 17,000 tons, about 95 per cent of which was produced in this country. The apparent consumption of "dead-burned" magnesite was approximately 172,000 tons, some 82 per cent of which was domestically produced. In both total quantity and percentage of material produced within the United States, these figures are record highs for many years past. UTILIZATION As indicated by these figures, the major tonnage outlet for magnesia is the refractories industry, in which magnesia is employed principally in three ways: (I) as dead-burned grain magnesite for the construction and maintenance of the hearths or bottoms of basic open-hearth furnaces; (2) in the form of refractory magnesite bricks and shapes; and (3) as a chemical

Jan 1, 1942

By Shiou-Chuan Sun

THE presence of an excessive amount of tough froth in the flotation of minerals, particularly coals, may create trouble in dewatering, filtering, and handling. Froth is also a nuisance in many chemical industries.&apos; This paper presents a study on the destruction of extremely tough froths with intense high-frequency sound. The data indicate that sound waves can be employed for continuous atandsoundwavescan instantaneous defrothing. A powerful high-frequency siren was used in obtaining the data. Also tested was an ultrasonorator of the crystal type with a frequency range of 400, 700, 1000, and 1500 kc per sec and a maximum power output from its amplifier of 198 w. The results, not presented, indicate that as now designed this machine is not suitable for defrothing. Although the sound generators of the magnetostriction type2,3 and of the electromagnetic type&apos;.&apos; were not available, it is beelectromagneticlieved they are capable of producing the required sound intensity for defrothing. The use of ultrasonics for defrothing was suggested by Ross and McBain1 in 1944. Ramsey8 reported in 1948 that E. H. Rose mentioned a supersonic device that broke down flotation froth but with low capacity. The writer has not been able to find any published literature containing practical experiments. Theoretical Considerations The mechanism of defrothing by sound is attributed to the periodically collapsing force of the propagated sound waves and the induced resonant vibration of the bubbles. The collapse of froth is further facilitated by the sonic wind and the heat of the siren. Sound waves can exert a radiation pressure&apos;," against any obstacle upon which they impinge. When a froth surface is subjected to the periodic puncturing of sound waves, the bubbles are broken. According to Rayleigh9 and Bergmann,12 the radiation pressure of sound, P, in dynes per sq cm is given as: P = 1/2 (r+1)i/v where r is the ratio of the specific heats of the medium through which sound is traveling and is equal to 1 on the basis of Boyle&apos;s law; i is the sound intensity in ergs per sec per sq cm, and v is the sound velocity in cm per sec. In this case, the accuracy of the formula is only approximate, because a perfect reflection can hardly result from a column of froth. In addition to the radiation pressure, the propagated sound waves cause the bubbles of the froth to have a resonant vibration.&apos;" he vibratory motion of the bubbles causes collision and coalescence, thereby weakening if not breaking the bubble walls. Sonic wind and heat were also generated." The sonic wind can exert pressure on the froth surface, and the heat can evaporate the moisture content of the bubble walls as well as expand the enclosed air. Apparatus The defrothing apparatus, shown in Figs. 1 and 2, consists of a powerful high-frequency siren, a glass or stainless steel beaker of 2-liter capacity with 12.4 cm diam and 17.1 cm height, and a metal reflector. The beaker was placed 2 in. above the top point of the siren. The metal reflector was adjusted to reflect and focus the generated sound waves into the central part of the beaker. Fig. 2 shows the crystal probe microphone used to measure the acoustic intensity and the mandler bacteriological filter employed to introduce compressed air into the beaker for frothing. The apparatus was enclosed in a soundproof cabinet equipped with a glass window. The siren, shown in Fig. 3, consists of a rotor that interrupts the flow of air through the orifices in a stator. The rotor, a 6-in. diam disk with 100 equally spaced slots, is driven by a 2/3 hp, Dumore W2 motor at 133 rps. The frequency of the siren can be varied from 3 to 34 kc. The maximum chamber pressure is about 2 atm, yielding acoustic outputs of approximately 2 kw at an efficiency of about 20 pct. The siren itself is relatively small and can be operated in any orientation. A detailed description of the siren has been given by Allen and Rudnick.11 Collapse of Froth To study the sequence of the collapse of froth, the glass beaker was partially filled with 920 cc water, 100 g of —150 mesh bituminous coal, 0.3 cc petroleum light oil, 0.2 cc pine oil and 1.54 cc Pyrene foam compound. This mineral pulp was agitated for 5 min and then aerated through a mandler filter until the empty space of the beaker, approximately 9 cm high, was filled completely with min-

Jan 1, 1952

By W. WANJUKOW, H. O. Hofman

(New York Meeting, February, 1313.) I. INTRODUCTION. IN the metallurgical treatment of most metallic sulphides it is usually necessary to carry on a roasting-operation. In some cases the raw ore will have to be roasted.; in others the intermediary product, matte, produced in smelting the ore; again, both ore and matte may have to be subjected to oxidation at elevated temperatures. Most metallic sulphides, when given an oxidizing-roast, pass through the state of sulphate before they are converted into oxides. All metallic sulphates are completely decomposed by heat, with the exception of those of lead and bismuth, but the temperatures at which decompositions take place vary with the metals. Some metallic sulphates are converted directly into oxides, others first form basic salts. Alkali-earth sulphates show a behavior similar to that of metallic sulphates, while alkali sulphates do not part with their sulphur trioxide even at elevated roasting-temperatures. The older data on the decomposition of metallic sulphates by beat are only approximations. Thus Kerl 1 gives the order in which metallic sulphates are decomposed with increasing temperatures as (Ag2, Fe, Cu, Zn, Ni, CO, Mn, Pb) SO4. More recent statements give definite temperatures and modify the formerly accepted order of decomposition. But the temperatures given by various observers do not agree. The reasons for this are to be found mainly in the method and manner of carrying out experiments. Four methods have been used: 1. Heating in an evacuated tube; 2, heating in a tube closed at one end, without air-cur-

Sep 1, 1912