Search Documents

By J. R. Long

The Federal Bureau of Mines has pioneered the work of preparing ductile titanium on a large scale and has also determined the basic properties of this new and most interesting metal. A number of reports (1, 2, 3: 4, 5) have al-ready been published, and considerable interest has been aroused in a number of industrial and research laboratories. Some of these laboratories have also published results of their work on the pure metal. Although the properties of titanium itself are quite promising, it is apparent that considerable improvement may be expected by alloying titanium with other metals. That is, pure metals in general have shown relatively large improvements in properties when alloyed with other metals and titanium is not considered to be an exception to the rule. Therefore, the emphasis of the investigations now under way in the Federal Bureau of Mines Laboratories has been placed on the study of the alloys of titanium, particularly the titanium-rich alloys. While the main interest is in the properties of such alloys, proper direction and evaluation of the work require at least a rough outline of the phase boundaries of the alloy systems involved.

Jan 1, 1949

By N. D. Shutler

This paper describes a numerical mathematical model of the steamflood process that depends on fewer restrictive assumptions than models previously reported. The solution, however, is obtained economically. Example calculations are presented that, on comparison with experimental results, tend to validate the model. Results that expose certain process mechanics are discussed. The model describes the simultaneous flow of three phases — oil, water and gas — in one dimension. It includes the effects of three-phase relative permeabilities, capillary pressure, and temperature- and pressure - dependent fluid properties. Interphase mass transfer of water-steam is allowed, but the oil is assumed nonvolatile and the hydrocarbon gas insoluble in the liquid phases. The model allows heat convection in one dimension and two-dimensional heat conduction in a vertical cross-section spanning the oil sand and adjacent strata. The hydrocarbon-steam gas composition is tracked, but the effect of gas composition on water-steam phase behavior is neglected. The model is solved numerically in three separate stages. The three-phase mass balances are solved simultaneously using Newtonian iteration on nonlinearities occurring in the accumulation terms. The energy balance is solved separately by noniterative application of the alternating-direction implicit procedure. Separate solution of the composition balance is accomplished by straightforward solution of the finite difference equations. The method of effecting nonsimultaneous, stable solution of the mass and energy balances is the key to the success of the model. INTRODUCTION Mathematical tools as well as laboratory and field experiments are necessary to help us understand the complex steamflood process. A mathematical model can expose process mechanics and show the relative importance of process variables, but this ability is often limited by restrictive assumptions. Most known models of steam processes,l-5 with the exception of the model of Gottfried,6 are "simplified" in that they involve analytic approximations and require many restrictive assumptions. The primary utility of these methods lies in the routine use as an aid in engineering design. By contrast, the comprehensive model presented here is numerical and requires far fewer restrictive assumptions. It finds its primary utility as a research tool. It serves as an aid in understanding the nature of the process, in interpreting laboratory experiments and in evaluating and developing simpler mathematical models for engineering design. The major reason why previously presented models have been confined to the "simplified" class is evidenced by the one published exception. In 1965, Gottfried6 presented a numerical model for the combustion process of which the steam process is a subset. The result is a comprehensive tool (though it neglects capillarity and two-dimensional heat conduction) that is troubled with convergence problems and that requires 2 to 3 hours of IBM 7094 time to complete a calculation. Though our present model does not simulate combustion, it does consider capillarity and two-dimensional heat conduction and it overcomes the convergence and computer-time problems. MATHEMATICAL DESCRIPTION OF STEAMFLOODING FLUID FLOW The equations employed to describe three-phase fluid flow are of a familiar form. Darcy's. law provides expressions for the velocities of the three phases (oil, water and gas), which, when combined with oil, water and gas mass balances, give the partial differential equations governing flow of the

Jan 1, 1970

By J E. Everett

When ore is being selected from a regularised block model, a common procedure is to accept as ore any block whose iron content exceeds a cut-off value, and whose content in each contaminant analyte is below an appropriate cut-off value. This method defines a quadrant within the multidimensional analyte space, such that any block lying within the quadrant is accepted as ore and any block lying outside the quadrant is rejected as waste. The cut-off levels can be adjusted to maximise ore tonnage at a target grade (or analyte vector). When the method is applied to a project comprising multiple pits with systematically differing grades, it is found that ore tonnage at target grade is maximised if different cut-off quadrants are used for the different pits. This is apparently illogical, because it implies that an ore block from one pit may be accepted as ore, but an identical block from another pit is rejected as waste, even when ore from both pits is to be blended into the same product and there are no production cost differences between the pits. The paradox is an example of the ætheory of the second bestÆ: if there are multiple conditions for optimality and one condition is broken, then obeying the other conditions may not be the best policy. The problem lies with the quadrant cut-off method, which is shown to be inconsistent even for selecting ore from a single pit. A criterion that is inconsistent cannot be optimal. It is shown that a linear composite cut-off function provides maximum ore tonnage, and that a single composite cut-off criterion is consistent and optimal over multiple pits. Further, it is shown that a composite cut-off function not only maximises ore tonnage at a specified composition, but also can be used to select ore so as to maximise project value, if marginal costs and values are available.CITATION:Everett, J E, 2013. Selection of ore from multiple pits, in Proceedings Iron Ore 2013 , pp 185-192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Lo-Ching Chang, J. Chipman

C. B. POST*—Just what are you showing that has not been shown by fixing the attention on molecular species and choosing the molecular species to give you a perfect solution? J. CHIPMAN (authors' reply)—In general a fairly satisfactory thermody-uamic treatment of slag-metal equilibria can be worked out on the basis of assumed molecular species in the slag. This has been the method used by Shenck and more recently by White. Winkler and I also used it in studying dephosphoriza-tion. Darken and Gurry found that it did not fit satisfactorily in the case of their data on iron oxides. The ionic formulas used here conform to the data much better and probably correspond somewhat more closely with the actual structure of the slags. C. B. POST—It does seem to be similar to you? J. CHIPMAN—It is alternative, and may lead to a more complete understanding. C. B. POST—Have you had a chance to talk to glass technologists on this? Have they been using this type of set-up for glass solutions? J. CHIPMAN—Yes, and the ionic formulas have given them a little better understanding of what liquid glass is like. C. B. POST—Nelson Taylor always said we were going- about slag reactions from the wrong viewpoint when using molecular species. Evidently the glass technologists use ionic species exclusively when dealing with liquid glass reactions. J. CHIPMAN—I agree that it seems more rational and more accurate to use ionic rather than molecular formulas. We should be cautious, however, and not suppose that we really understand the structure of a slag just because we are able to fit its reactions by ionic equations.

Jan 1, 1950

By Robert F. Chaiken, Thomas H. Dubaniewicz, Gregory M. Green, Kenneth L. Cashdollar

Optical technologies have progressed rapidly in the past 15 years. One application of laser technology in underground coal mines currently under evaluation is the remote measurement of explosive methane gas. Federal regulations require that atmospheric monitoring systems used in gassy underground mines where permissible equipment is required shall be intrinsically safe. Mine Safety and Health Administration criteria for the evaluation and testing of intrinsically safe apparatus and associated apparatus contain no specific guidance for optoelectronic components such as diode lasers. The National Institute for Occupational Safety and Health is conducting a study to help provide a scientific basis for developing appropriate safety guidelines for optical equipment in under- ground coal mines. Results of experiments involving ignition of methane-air mixtures by collections of small heated particles of Pittsburgh seam coal and black iron oxide are reported. The inert but more strongly absorbing iron oxide targets consistently ignited methane-air mixtures at lower powers than the coal targets. Minimum observed igniting powers for laser energy delivered by 200, 400 and 800 pm core fiber optic cables and directed onto iron oxide targets in methane-air atmospheres were 0.6, 1.1, and 2.2 W, respectively. Comparisons with the results of other researchers are made. A thermal layer theoretical approach to describing the process is included as an appendix.

By Muhlis Nezihi Saridede, Burak Birol

"Plastic wastes become a huge problem day after day due to the growth of plastic industry. Hence, plastic wastes are used as a raw material for other industries to eliminate this problem. Polyethylene Terephthalate (PET), which is a commonly used for plastic bottles, may be used as a reductant for iron production because of its C and H content. In this study, composite pellets containing iron ore concentrate, flux and reductant were prepared. Crystallized PET bottles and coke were used as reductant after ground. The prepared pellets were reduced at 1400°C for 30 min. and iron nuggets were produced successfully. Usage of waste PET purely as reductant in composite pellets gives a higher metallization degree and proper carbon content than coke or PET and coke mixture.IntroductionPlastics can be seen everywhere, especially at packaging industry in our common life. The increase of plastic usage ends up with an important problem, the increase of plastic wastes. Many studies have been carried out about usage of plastics as reductant in blast furnace such as Ogaki et al.[1], Heo and Baek [2], Saridede [3], Minoru et al.[4], etc. Besides, Kato et al. [5], Nomura and Kato [ 6] and Rongfang et al. [7] have pointed out the use of plastics in coke ovens regarding to its calorific content. In EAF steelmaking, a mixture of coal/coke and plastics can be used as an energy resource instead of only coal or coke. [8] Also, the usage of PET and PC in self-reducing composite pellets increased the reduction rate. [12]PET (Polyethylene terephthalate ), which is commonly used for soft drink plastic bottles, is an important municipal waste due to its C and H content. Its molecular formula is (C10H8O 4)n. Demir and Dincer showed that PET can be crystallized at 250°C to have the ability to be ground to a size of -100 µm. [11]"

Jan 1, 2011

By Walter S. Bergholz, Michael L. Schreder

"Since Escondida began operations in fiscal 1991, a series of aggressive expansion projects have enabled market share to be increased and ever larger profits to be realized. This was possible due to the very large size of the ore body and its high grade - averaging 2.7% copper from startup through fiscal 1997. The situation has now changed: ore grade is falling rapidly and is projected to be only 1.55% by 2003. Since revenue is directly proportional to ore grade, while costs are proportional to quantity of ore processed, profits will begin to fall dramatically. The Phase IV Expansion Project is intended to forestall this drop in profits by increasing ore processing capacity by over 85%.The Phase IV concentrator is designed for a nominal capacity of 110,000 MTPD and the key to achieving this value is through the proper design of the grinding circuit. This paper presents the general design criteria for the grinding circuit, as well as a description of the facility.INTRODUCTIONThe Phase IV Expansion Project consists of a new copper concentrator located 8.5 km south of the existing operations, a new tailings disposal and water reclaim system, a new concentrate slurry pipeline to the coast, and added concentrate handling capacity at the port of Coloso. The new concentrator has a nominal capacity of 110,000 tonnes per day (MTPD), compared to the existing concentrator’s capacity of 127,500 MTPD. The Laguna Seca concentrator is based on using the largest and most efficient ore grinding mills now available.The concentrator has been designed for a 110,000 MTPD nominal capacity. The process design criteria for the Phase IV project were established from in-house operating information and from test work. Unlike a green field project, Escondida already had an operating plant and it processes ore from the same pit that feeds the Phase IV plant. It is expected that the current mineralization will be similar for the first 6 years of operation of the new project. Therefore, some of the current plant operating conditions were incorporated directly into the design criteria."

Jan 1, 2004

By P J. Howard, P Darvall, J H. Mainwaring

In less than a year, Atlas Iron’s Corunna Downs Project has moved from a new discovery to a substantial resource of high quality in an underexplored greenstone belt. Located approximately 170 km south-east of Port Hedland and 40 km south-west of Marble Bar, in the Pilbara Region of Western Australia, Atlas Iron Ltd (Atlas) has conducted extensive exploration work at Split Rock, Razorback, Runway and Shark Gully, consisting of geophysical surveying, field mapping, 464 reverse circulation and 16 diamond drill holes resulting in a current resource of 51 Mt at 57.3 per cent Fe (Atlas, 2014b).The Corunna Downs Project is interpreted to be hosted within the Cleaverville Formation of the Archaean Gorge Creek Group. Within the project area these rocks outcrop as subvertically dipping banded iron-formations (BIFs) and jaspilites, cherts, minor shales and meta-sediments forming a north–south trending plateau.Primary hematite-martite iron mineralisation is overprinted in the near surface environment by supergene goethite, and frequently capped with a thin laterite cover. The strongest enrichment areas have been discovered within topographic lows, proximal to fault zones, which coincide with a geophysical anolmaly. These characteristics were targeted, and the subsequent areas mapped in greater detail, allowing for efficient resource definition.Although first explored for iron in the late 1960s, it wasn’t until Atlas’ acquisition of the project in October 2012, that major strides were made to defining an economic resource. At present, Corunna Downs is Atlas’ best greenfields exploration discovery, both in terms of the potential scale of the resource and its blending capacity.The Corunna Downs prospect is emerging as a major new iron ore province in the Pilbara and includes 80 km of potential host stratigraphy. Corunna Downs sits strategically between Atlas’ Mt Webber and McPhee Creek tenements, and can play an important part in Atlas’ growth strategy as iron ore market conditions become more volatile and challenging.CITATION:Mainwaring, J H, Howard, P J and Darvall, P, 2015. Discovery of the Corunna Downs deposits, in Proceedings Iron Ore 2015, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Armstrong

This is a world of change and has been from the beginning. There are constant efforts on the part of natural forces to wear down the high spots and fill in the low spots. Wind and water over eons of time tunnel through obstacles and build windways and waterways to make movement of air and water easier and more efficient. It is a natural, never ending, ever changing continuing effort. Man in his struggle to survive, and to progress, has had to adapt the terrain of the earth to fit his needs the best he could. First, he used natural caves to protect him from the elements; then he learned how to build earth and rock-moving tools from antlers, bone, rocks, and sticks and adapted his cave to increase his security and provide better protection from heat and cold and from his predatory enemies. As his numbers increased, so did the necessity of further adapting his environment to accommodate his needs. Water was usually not available when and where needed, especially in the desert areas where civilization developed, and long tunnels were drilled to intercept ground waters and lead them to underground caves carved out of soft limestone. Most of the tunnels of early man were to bring water from where it was to where man needed it. Then, as now, as man increased his chances for physical survival, he turned to the quality of life -- and this reflected in the concern for life after death. This lead to the elaborate shafts and tunnels for the protection and prservation of the more affluent noblemen and pharaohs of the early Egyptian civilization. Man used the underground for the stable temperature and for protection and safety.

Jan 1, 1974

By R. T. C. Rasmussen

"INTRODUCTION The primary purpose of the Bureau of Mines electrolytic manganese pilot plant at Boulder City, Nev., is to improve the Bureau-invented electrowinning process and to determine the applicability of the process to the extensive domestic low-grade manganese ores with a view to making the United States dependent upon foreign sources of manganese. 3/4/ Incidental to accomplishing this purpose, the pilot plant has produced a substantive quantity of electrorytic manganese since the start of operations late in 1941; present cabacity about 1 ton a day of manganese metal. A second important purpose of the pilot plant is the supplying of electrolytic manganese for full-scale tests in cooperation with industrial users of manganese.The Rustless Iron& Steel Corp., Baltimore, Md., was the first steel company to cooperate with the Bureau of Mines in large-scale testing of electrolytic manganese. Arrangements were made with C. E. Tuttle, then president of the corporation, whereby the Bureau would supply electrolytic manganese to make a sufficient number of full-scale stainless-steel heats to demonstrate thoroughly its merits as a replacement for low-carbon ferro-manganese in the corporation's stainless-steel practice. The corporation's purpose in the investigation was to determine the possible advantages of electrolytic manganese resulting from its almost complete lack of phosphorus and caroon that might offset its then considerably higher cost per unit of manganese than low-carbon ferromanganese. The data presented herein are based upon reports of A. L. Field, technical director, and L. Weitzenkern, research engineer of Rustless Iron & Steel Corp.; they are supplemented by observation of the author who visited the plant during the tests."

Oct 1, 1945

By K. J. Fair, G. Van Weert, J. E. Schneider

"IntroductionCyanidation is the principal process for extracting gold from ores . Many primary gold ores, however, are partially or totally refractory in the conventional cyanidation process.Considerable success has been achieved with new gold leaching techniques, such as intensive cyanidation, pressure cyanidation, carbon-in-leach cyanidation, etc. These techniques however, do not offer substantial gains in gold extraction from refractory pyrites.The more drastic pretreatment processes such as roasting, chemical oxidation, autoclave oxidation, and bacterial oxidation all utilize oxidation to break down the structures of pyrite and arsenopyrite. This generally renders the gold amenable to cyanidation.Comparative cost studies indicate that the oldest commercial pretreatment method, i.e. high temperature roasting, is currently the least expensive option if the sulphuric acid can be sold. It operates with air at atmospheric pressure and is characterized by fast reaction rates. For an alternative hydrometallurgical con centrate treatment method to be competitive, it too should operate with air at atmospheric pressure and with fast reaction rates. The NITROX process meets these conditions."

Jan 1, 1986

By J. Marsden

Lift height, overall heap height and climate all play an important role in determining precious metals leaching rates, recoveries, operating costs and capital cost requirements for heap leaching operations. The effects of these factors are not easy to predict from testwork, and this can result in unexpected delays in metal production, lower recoveries than expected and higher capital and operating costs than necessary. This paper investigates the economic impact of lift height, overall heap height and climate on heap leaching and provides criteria to assist in the design and operation of leaching facilities. Descriptions of three heap leach operations in the western USA are provided to support the discussions and conclusions.

Jan 1, 1995

By Bart Blanpain, Muxing Guo, Bin Yang, Fei Wang

An experimental investigation of the precipitation behavior of the Dy2O3 containing slag during cooling was carried out in this work. The slag with composition 45 wt% SiO2—49 wt% CaO—6 wt% Dy2O3 was equilibrated at 1673, 1773 and 1873 K for 24 h in an argon atmosphere, and then quenched in water to determine the phase relations. The composition and microstructure of the equilibrated phases of the systems were determined by EPMA/WDS. The precipitation behavior of the REEs containing phases during cooling was studied by using an in-situ confocal scanning laser microscope (CLSM) observation technique combined with an infrared imaging furnace heating (IIF). Data resulting from this work aims to support further investigation on separation of rare earths from metallurgical slags.

Mar 1, 2018

By Hossaini SMF

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Ramamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris: 611=1+B(63)O.825 acm 6cm where a1= axial compressive stress at failure, MPa; a3 = confining pressure, MPa; acm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (aim ) -0.185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By C. Sykes, E. Turner, M. Wyart-Remy

This paper follows that of the Milos Conf, 2002 and examines the collection and reporting of SDIs in the industrial minerals industry in Europe. It compares the characteristics of the GRI Reporting Guidelines, with its Metals and Mining Sector Supplement with those of the EU DG Enterprise Scheme, launched in 2001. The particular issue of SME's and companies which are not publicly traded is examined. The pros and cons of participating in such schemes is a central theme of the paper. The paper concludes that there and many business benefits for these companies in participating and submitting their data. The European Commission Scheme is strongly recommended for companies in the sector which are SME's and not-publicly traded as well as large firms who are listed on European Stock Exchanges.

Jan 1, 2005

By Andrew Budek

"Analytical and experimental work has shown that achieving the full inelastic lateral capacity of a pile may require the formation of a plastic hinge below ground level, in the pile shaft. The confining action of soil about the pile shaft was further been shown to greatly enhance the ductility capacity of the pile. An experimental program was therefore undertaken to build in the effect of external confinement through the addition of a GFRP jacket to the subgrade plastic hinge region. Two piles were thus modified, and compared to an unjacketed pile in a test rig which simulated a subgrade moment pattern and soil confinement. The ductility achieved by the jacketed piles was found to be substantially lower than an unjacketed control specimen. Failure mode of the jacketed specimens was also undesirable, involving complete tendon rupture and sudden loss in capacity IntroductionSeismic loading of concrete pile shafts can result in a demand for inelastic response. In the case of a superstructure supported by a single pile (i.e., a pile-column forming a single-column bridge pier, in which there is no rotational restraint at the top of the pile}, a plastic hinge will form below grade, at a depth which varies with soil properties and above-grade height of the center of seismic mass.In the case of a superstructure supported by multiple piles, there is rotational restraint, and the connection will experience inelastic action first. However, development of the full lateral inelastic capacity of the pile may call for the formation of a second, subgrade plastic hinge (fig. 1 )."

Jan 1, 2005

By A. L. D. Skury

In the synthesis of diamond, the precursor graphite must present a degree of crystallinity to assure optimum yield and quality for the transformed crystals. X-ray diffraction, SEM and TEM analyses were carried out to investigate the structural and morphologic transformations produced in natural graphite by high pressure-high temperature treatment. The present study had as its objective to characterize the morphological and structural changes suffered by a natural graphite that was subjected to high pressure and high temperature treatments in the region of diamond thermodynamic stability. The results indicate that the material that constitutes the gasket, for the deformable capsule, could act as catalyst in the graphite recrystallization process.

Jan 1, 2006

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By R Simonato

It is now recognised that rotary sample division is by far the best laboratory tool for extracting subsamples from a lot of material. In terms of sampling theory, rotary division, by virtue of the fact that it can extract many increments from the lot during the division process, radically reduces the variance due to distributional heterogeneity in the sample being divided. There are a number of occasions in sample preparation when it is necessary to extract a subsample of a target mass. To do this with rotary dividers taking a fixed fraction of the starting mass is a tedious task. In response to this problem, a variable split sample divider has been designed and built for the mineral industry. This paper discusses the utility of the device and presents test data showing that the machine is capable of making accurate mass split while overcoming segregation in the material being divided.

Jan 1, 2008