Search Documents

By F. C. Langenberg, J. Chipman

New data on the distribution of silicon between slag and carbon-saturated iron at 1600oand 1700oC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1700°C for slags containing up to 20 pct Al2O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A1203-SiO2 slags over a range from zero pct A12O3 to saturation with A12O3, or CaO.2A12O3. The upper limit of SiO, is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently, 4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/A12O3 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al2O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al2O3 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al,O3 and of A120,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO, (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2 The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

By I Gipps

A vision of what the future mine involves all aspects of mining, ie orebody access, ore stoping, material transport, processing and waste material disposal. This paper examines one aspect of the future mine: rock extraction, stoping, automated for remote operation, high productivity and low cost. Concepts for the future require a re-think of the mining process and ROES® re-examines how bulk stoping of ore can be undertaken and how this should be redesigned to accommodate the possibilities that exists with remote control and automated operations.ROES® is a new mining system for underground mines and quarries utilising a shaft located close to or within the stope for the ore breakage process. The system is designed to exclude personnel from contact with production drilling, explosive placement and detonation so all of these tasks are remotely controlled or automated. Survey of the shaft, stope back and broken rock within the stope will occur, following each blast, by remote control or automated techniques. The survey will include excavation geometry, rock fragmentation, geotechnical characterisation and estimation of ore grade. Blastholes will be surveyed before placement of explosives and, with the survey data, the optimal explosive placement and blast timing will be determined with the best available information.ROES® is designed for application in open stoping or sublevel caving in disseminated, geologically defined, thick tabular or narrow vein ore bodies. Technologies developed for ROES® will also have potential applications to caving operations, reducing the risk of frozen ore and poor fragmentation. In a typical sublevel open stope application, ROES® will reduce the stope associated development by half and will allow ore to be brought on-stream sooner and at lower cost. Other savings will flow with the centralisation of mining activities and operational data, reduction in mining fleet, reduction in ventilation requirements, improved occupational safety and reduced mine complexity.

Nov 22, 2011

By John J. Laffin

"Nova Scotia Department of Mines and Energy Throughout the history of Nova Scotia, trends in the production and use of its coal resources have resulted in major impacts on the economy and society of the province. Current trends in coal demand locally, nationally and internationally are having and will have an increasing positive effect on Nova Scotia over the next twenty years-in terms of energy supply, job creation and general economic development. Coal for electrical generation is an immediate and key objective of Nova Scotia's energy plan; and, in the long term, coal-derived fuels will meet the province's needs for transportation fuels. Demand for metallurgical coal is also expected to increase, especially if the merchant coke plant currently under investigation becomes a reality.Meeting these coal supply and utilization objectives in the face of increasing environmental, social and economic constraints poses a tremendous technical challenge. Work has begun on projects to expand coal production capacity and to adapt new technologies for coal preparation and utilization to the specific needs of Nova Scotia; much more work will be required in the coming decade in order to succesfully tap this resource.IntroductionThe energy problem facing Atlantic Canada has a few unique features not found in the rest of the country. Canada, as a whole, has access to a diverse mix of energy resources, including crude oil, natural gas, coal, hydro and uranium, with the result that crude oil supplies only about 40 per cent of Canada's primary demand. In contrast, foreign crude oil dominates Atlantic Canada's energy mix, supplying over 70 per cent of the primary energy demand.This results in important differences in various sectors. Nationally, about 5 per cent of the electricity is generated from oil whereas last year in Nova Scotia approximately 40 per cent of the electricity generated was from imported oil. Residential, commercial and industrial space heating, and industrial process heating in Atlantic Canada was almost 100 percent dependent on foreign oil. This is in sharp contrast to the situation in central and western Canada, which have access to secure domestic natural gas, oil and hydro electricity."

Jan 1, 1982

By C. C. Merrill

Studies were made to determine the amenability of yttrium to fused-salt electrorefining in a controlled atmosphere. Tests were conducted in a LiCl- YCl3 electrolyte system at 710° C. The major variables studied were the YCl3 content of the electrolyte, from l.7 to 13.4 mol percent, and the initial cathode current density, from 410 to 1,630 amperes per square foot. Vacuum distillation was employed to remove salt from the deposited metal. Metallic impurities, except for lithium, could be reduced to near or below their lower analytical limits, ranging from 10 ppm for Cu to 300 ppm for Ta; reduction of oxygen content, however, was accomplished only in metal produced from electrolytes with 5.4 mol percent YCl3 or less. Initial cathode current density had little effect on the purity of the product.

Jan 1, 1967

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757' and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick 'needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,' are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed' by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke's law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

IT will be noticed, from the following contributed papers on the various plant, what an infinite number of parts are required to be kept in active operation in order to derive a resultant product of commercial value from the ores and materials received at the works. Crude ores and concentrates, in every degree of complex structure and resistance to treatment, are arriving daily from near and distant places, moreover their metallic contents are so varied that an outsider, unacquainted with the operations, would naturally wonder how it is possible that the rare elements are to be sorted out and classified into their true order, to meet industrial requirements.The proposition is necessarily not a simple one and owners of mining properties have naturally refrained from smelting their complex ores on account of the technical difficulties of attaining high efficiency and recovery of the metals, where limitations are imposed in procuring a variation of ores that lead to the best smelting and refinmg result. This difficulty obviously imposes many disabilities on the smelter, who is prepared to accept all such complex ores, and it may be said that were therenot available a large weekly supply of lead concentrates from the company's own mine at Broken Hill, of standard quality, much of the material being treated in the world today would certainly not be marketable.In order to sustain full efficiency, each section of the works must maintain its.true balance and synchronize with the requirements of such other departments as are dependent on its partially treated materials. This harmony of operations is not only imperative as regards tonnage output, but also relies on the condition of the resultant treatment by each plant, no large variations being permissible.The various officers are, therefore, dependent on one another to keep the order of the operations flowing regularly. This is accomplished by constant intercommunication and observation, as...

Jan 1, 1918

By Wei-Tong Du, Xiao-Ping Liang, Yu Wang

The structural properties for ternary molten CaO–SiO2–B2O3 system with varying B2O3/SiO2 ratios at a fixed CaO content were calculated by molecular dynamics (MD) simulation. The simulation results revealed that with the increasing of B2O3/SiO2 mol ratio, the bond length of B-O was approximately constant at 1.35 Å, and the coordination number for B (CNB-O) was observed to vary from 3.40 to 3.51, and the average angle of O-B-O increases from 105° to nearly 120°, implying that the geometric stability of structure is reducing sharply. AlsoQ3 andQ4 tetrahedral species (tetrahedron with three and four bridging oxygens respectively) decrease with the increasing of B2O3/SiO2 mol ratio, and the proportion of (Q3 + Q4) decrease linearly from 0.6 to nearly 0, suggesting that B2O3 may behave as a network-breaking basic oxide in the CaO–SiO2–B2O3 system.

Mar 1, 2017

By S. R. Smith, W. M. Voorhis, J. D. Young

The Tennessee Valley Authority (TVA) has conducted investigations to identify the major causes of coal pile inventory adjustments. This paper describes past and current attempts to improve inventory survey accuracy and reduce costly inventory adjustments. The unique interaction between accountants and engineers is also reviewed. Data and results of a recent field test wing downward-looking radar developed by Ohio State University are presented. These show great promise in determining coal pile depth and density, thus improving inventory accuracy. This electromagnetic remote sensing technique, if successful, would provide an optimum technical and economic method of surveying all 12 TVA stockpiles without costly borehole drilling or disrupting stockout and reclaim activity. The effect of changing coal quality to meet environmental standards has made accurate coal pile density measurement more important than ever in reducing the costs of electric power generation from coal.

Jan 1, 1984

By Leons Kovisars

Introduction Labor is the major cost element for most mining operations. Labor costs are continually increasing, both in nominal and constant terms. This is true in developed as well as less developed countries. There are two ways to control unit labor costs - labor costs per ton of ore mined. Replace labor with capital (increased mechanization) or improve productivity (reduce the labor force). Every miner is aware of specific inefficiencies at his or her particular operation. But the miner has no comparative measurement standards. So it is difficult to know whether these inefficiencies are major or minor. The miner may also be unaware of large-scale inefficiencies because ongoing labor practices may have caused management complacency. Met Research studied mining labor productivity. The firm collected pilot data by sending direct-mail questionnaires to 320 nonferrous mining operations around the world. The response rate was 27%, of which 78 operations provided full data on production and employment.

Jan 11, 1983

With rapid development of Chinese iron & steel industry, it is of significance to intensify the utilization of domestic complex iron ore resources. The tin, zinc-bearing complex iron ores are typical polymetallic and intractable ones because of the complicated intergrowth relations among the multi-elements, and they have not been efficiently utilized, presently. Based on the thermodynamic analysis of iron, tin and zinc oxides reduction by CO, the technological conditions of tin and zinc recovery and pellets preparation from tin, zinc-containing iron concentrates by selective reduction roasting are studied and a new comprehensive utilization process is developed in this investigation. Under the optimum conditions, the tin and zinc volatilization is respectively in excess of 80% and 70%, and the compression strength of roasted pellet is more than 2500 N/P. Moreover, the residual tin and zinc in the finished pellets is below 0.06%. The finished pellets can be used as high quality iron-making burdens for large-scale blast furnace.

Jan 1, 2014

By Richard E. Sylwester

Evaluating surface and subsurface conditions for marine foundations (bridges, causeways, terminals, etc.) is often done with a limited amount of data. Subsurface information for these projects is primarily acquired using traditional methods, such as boreholes, test pits or divers, which tend to be expensive and limited in the area of coverage. A number of geophysical methods, including precision bathymetry, sidescan sonar, and seismic reflection or subbottom profiling are extremely cost-effective and obtain significantly more data than can be acquired using traditional intrusive methods. These geophysical methods provide detailed surface images and continuous profiles of the subsurface stratigraphy. This information can be invaluable for selecting the best location for geotechnical boreholes and to map potential geohazards such as submarine slides and filled or open scour holes. Offshore investigations conducted for a proposed highway bridge (Knik Arm Bridge, Cook Inlet, AK), the retrofit of two existing bridge (Antioch and Dumbarton Bridges, CA) and a proposed cruise ship terminal (Ketchikan, AK) used a combination of geophysical methods to map water depth, detect and map debris on the seabed, map the thickness of unconsolidated sediment, determine the depth to bedrock and identify potential geohazards such as scour holes. The results of the geophysical investigations will be used to select locations for obtaining geotechnical borings, to extrapolate geologic information between existing or proposed boreholes, evaluate the potential depth of scour and design a pile support pier. Geotechnical engineers, offshore contractors and bridge designers are realizing the importance of the early use of offshore geophysics for (i) site characterization, (ii) to reduce the uncertainty of geotechnical conditions thus avoiding designs that may be overly conservative and thus more expensive and (iii) to assist in selecting locations for geotechnical borings.

Jan 1, 2013

By P. M. Kelly, E. P. Butler

Four Mn-CLL alloys, containing 60, 70, 80, and 90 pct Mn, respectively, have been examined in the quenched and the quenched and aged conditions using electron microscopy and electron, neutron, and X-ray diffraction. After certain heat treatments the alloys transform from fee to fct and in the tetraom1 condition show a domain structure parallel to {101} planes. Neutron diffraction indicates that the domains are antiferrornagnetically ordered. The domain boundary contrast has been examined using bright- and dark-field microscopy, and the contrast effects observed under favorable conditions have been used to deduce the c axis orientation in each domain. The domains are extremely mobile and can be nucleated at precipitate particles and screw dislocations. The domain mobility is responsible for the high damping capacity. In the aged material a Mn precipitates in the Kurdjumov-Sachs orientation and results of both electron microscopy and neutron diffraction indicate that the matrix separates into two components—one rich in manganese and the other rich in copper. ALLOYS of manganese and copper have the unusual combination of a high damping capacity and good mechanical properties and have been the subject of a number of investigations as part of a general interest in high damping capacity alloys for engineering purposes.&apos;,&apos; SO far, however, there has been no reported electron metallographic study of these alloys. The Mn-Cu system has an extensive range of solid solubility at high temperatures, and the equilibrium phases are expected to be y (fee) and a Mn. The high damping capacity is associated with a metastable tetragonal structure of variable c/a ratio, which forms from the high-temperature y phase. This latter phase becomes more difficult to retain as the manganese content increases, and alloys containing more than 82 wt pct Mn undergo a reversible martensitic fcc — fct transformation on quenching. The X-ray work of Basinski and christian3 showed that the Ms temperature for the transformation was below room temperature for alloys in the range 70 to 82 pct Mn and increased linearly with manganese content. When quenched from the y region, alloys in the range 50 to 82 pct Mn are cubic at room temperature, but become tetragonal if aged at temperatures between 400" and 600°C. The martensite transformation occurs on cooling from the aging temperature. Tetragonal alloys have a banded microstructure and the bands analyze to be traces of (110) planes. Similar microstructures have been observed in In-Tl4 and in other manganese-base systems, such as Mn-Au5 and Mn-Ni.6 The mobility of the bands in Mn-Cu alloys can be demonstrated by optical examination of a polished specimen surface subjected to a cyclic stress.7 The bands appear and disappear as the stress is varied, and X-ray measurements of the (200,020) and (002) peak intensities confirm that a reversible reorientation of the tetragonal structure occurs. Meneghetti and sidhu8 investigated the magnetic structure of Mn-Cu alloys and found antiferromagnetic ordering in furnace-cooled alloys of composition >69 at. pct Mn. Magnetic super lattice reflections occurred at the (110) and (201) positions and the proposed structure was fct with the spins along the c axis. A more complete investigation by Bacon et al.9 confirmed this structure. The magnetic ordering temperature Tn was found to increase linearly with manganese content in the same way as the Ms temperature, and at any composition, Tn > Ms. This relationship suggested that the magnetic ordering was responsible for the cubic — tetragonal transformation in the manganese-rich alloys. The purpose of this investigation was to study the mechanism of high damping and the structural changes that occur on aging. The main technique used was transmission electron microscopy, but X-ray and neutron diffraction experiments were also carried out. EXPERIMENTAL Materials and Heat Treatment. The four alloys, provided by the Admiralty Materials Laboratory. were of nominai composition 60, 70, 80, and 90 Mn and all had low impurity levels, <0.05 pct C, <0.2 pct Fe. This material was cold-rolled to 200-µ strip with intermediate annealing and then given a final heat treatment of 24 hr in the range 800° to 900°C followed by water quenching. An identical heat treatment was given a length of 3/4-in.-diam bar of the 70/30 alloy from which the neutron diffraction specimens were machined. It was suspected that the tetragonal structures would be metastable at room temperature, and so the alloys were not aged until required for experiments. After aging in a salt bath the alloys were water-quenched. Thin Foil Preparation. Initial thinning to 50 to 75 µ was possible in a solution consisting of: 50 ml nitric acid 25 ml acetic acid 25 ml water The surface deposit and grain boundary etching was removed by a final electropolish at around 20 V in an electrolyte consisting of:

Jan 1, 1969

By Walter E. Montgomery

ACCIDENT-PREVENTION work in years gone by has been carried on by many mine managers as a philanthropic movement, but in recent years they have come to realise that Safety is good business and pays tangible dividends. Let us begin with the word itself. We are told that an accident is "any-thing occurring unexpectedly, undesignedly, or without known or assign-able cause&apos;. It is further explained that it is any &apos;unpleasant or unfortunate occurrence involving injury, loss, suffering, or death", and, finally, "any unintentional or non-essential circumstance". We admit that accidents are unfortunate, unpleasant, unintentional, and they generally happen undesignedly and to a great degree unexpectedly, but to say that they happen "without known or assignable cause" leads us to believe that the word &apos;accident&apos; is often misused. Would it not be more correct to say that a man suffered a "personal injury"? The word &apos;accident&apos; in its proper sense implies something over which no one has any control, but when the majority of all so-called accidents are analysed we arrive at the incontestible fact that some act or action, previous or present, was the underlying cause. As long ago as the year 1556 this fact was mentioned by Georgius Agricola, who, in writing a paper on metallurgy, aptly stated, "It remains for me to speak on the ailments and accidents of mines, and of the methods by which they can guard against these, for we should always devote more care to maintaining our health, that we may freely perform the functions of our body, than to making profits". Farther on, Agricola relates in more detail, "Sometimes workmen slipping from ladders into the shafts break their arms, legs, or necks, or fall into the sumps and are drowned; often, indeed, the negligence of the foreman is to blame, for it is his special work both to fix the ladder so firmly to the timbers that they cannot break away, and to cover so securely with planks the sumps at the bottom of the shafts, that the planks cannot be moved nor the men fall into the water; wherefore the foreman must carefully execute his own work. Moreover, he must not set the entrance of the shaft-house toward the north wind, lest in winter the ladders freeze with cold, for when this happens the man&apos;s hands become stiff and slipping with cold, and cannot perform their office of holding. The men, too, must be careful that, even if none of these things happen, they do not fall from their own carelessness&apos;.

Jan 1, 1938

By P. Christmann

"In June or July 2005, the European Commission will present its Thematic Strategy on the Sustainable Use of Natural Resources proposal to the Council and European Parliament, one of the seven Thematic Strategies to be developed and implemented under the 6th European Environment Action Programme in support of the European Union’s Sustainable Development Strategy defined by the European Union’s Head of State at the Göteborg European Council, in June 2001. The time scale for this Thematic Strategy is 25 years (2005-2030). This paper discusses some of the key issues related to the EU minerals and metals industry that needs to be addressed by the Strategy. These are: - the need for access to mineral reserves in the EU and abroad; - the need to strenghten the capacity of developing countries to sustainably promote and regulate the use of their mineral potential; - the need for an EU mineral resources intelligence capacity. There are additional important needs, which are not discussed in this paper, such as: - the need to foster further innovation in mining, ore beneficiation and metallurgical technologies; - the need to integrate and simplify the exisitng complex regulatory framework applicable to the EU mining industry and to effectively implement existing legislation."

Jan 1, 2005

By Paulo Roberto Gomes de Sousa

O trabalho mostra a analise de energia e exergia de uma unidade termoelétrica, esta planta consiste em um ciclo regenerativo. Serão comparados os nivéis de irreversibilidade dos componentes que compõem a unidade. A escolha do ciclo regenerativo com a referência em análise, é devido sua eficiência global. Isso é proporcionado através do aquecimento da água de alimentação da caldeira, com isso, consequentemente ocorre uma diminuição da necessidade de energia imposta na caldeira. A análise realizada também mostra as irreversibilidades da planta através da análise de exergia.

Aug 17, 2017

In order to do the discharge estimation better, it is valuable to find out appropriate formulas for estimating discharge in various pits, based on accumulating data, summarizing discharge patterns applying optimum seeking method and principle, by seeking redical exponent with help of the method of exhaustion, as well as testing and making statistics, in accordance with the quality standards established by our practical experience.

Jan 1, 1988

New and more cost-effective methods of haulage and hoisting will be needed to develop the underground mines of the future. A review of the development of technology since the 1950s shows that once mechanised equipment became available it took 25 years for appropriate mining methods to be developed and the equipment made reliable, then a further 25 years to reach todayÆs level of automation and reliability. Suggestions are made about possible areas for ongoing research with the observation that there is little research worldwide into disruptive technologies. A call is made for better organisation and presentation of the opportunities and potential benefits of new underground mining technologies.

Jan 1, 2005

By S. G. Malghan, V. K. Pujari

Detailed characterization of all the powder constituents during powder processing is necessary for the reproducible manufacture of ceramic components that will perform reliably in intended applications. In this paper, selected physical and surface chemical techniques for characterization of silicon nitride powder are evaluated. The characterization data are discussed in the context of how these data, through their influence on powder processing unit operations, can affect the final microstructure. In the forming of ceramics, some of the major variables of injection molding are evaluated. Accurate measurement and control of these variables is emphasized for manufacture of Si3N4 ceramics with a high degree of reliability.

Jan 1, 1990

By R. Lepsoe

THE basic products of the Company are lead and zinc. Around 950 tons of these metals are produced each day. In the last decade, the production of by-products has increased to such an extent that they are now nearly as large an operation as that of the base-metals. Of the many by-products, the most objectionable, and up to a few years ago the most useless, was the sulphur. The sulphur comes in the ore from the Sullivan mine. It is in the ore chiefly as lead, zinc, and iron sulphide. By selective flotation, these three sulphides are separated into the lead concentrates, the zinc concentrates, and the mill tailings. These mill tailings contain the bulk of the iron and the sulphur. Of the 6,5CO tons of ore treated per day, about 5,000 tons are wasted to the mill tailings dump, and, while now valueless, will in future years undoubtedly be used as a source of iron and sulphur. There are about 1,500 tons of sulphur and 2,200 tons of iron per day in the tailings, and about 400 tons of sulphur left in the total concentrates. In the recovery of lead and zinc in the pure form, the first step is the roasting operation. Here, most of the sulphur is driven off as sulphur dioxide in the gases. It has always been apparent that this sulphur should be. recovered and utilized if possible. At the same time, this would cure the smoke nuisance. Because, in spite of the low concentration of sulphur dioxide and the fact that it was discharged from stacks at an elevation of 400 feet above the plant, some damage to vegetation close to the plant had been experienced.

Jan 1, 1937

Our ultimate resources come from the Sun and the Earth System. At this time we face a world crisis in energy, water and soil resources. Global pollution problems are increasing in almost all nations. There is an urgent need to use our vast knowledge with a new wisdom and this requires new integrated teams of experts to provide the best alternatives for the needed new development problems. These teams must include economists, engineers and a broad spectrum of scientists. Today it is possible to produce clean energy, stop soil erosion, clean water and reduce and use wastes of many types.

Jan 1, 1995