Search Documents

By Joshua Micah Hoffman

While it is easy to state that meaningful involvement of the community can play a critical role for a successful blasting operation, following through with this involvement is not an easy task. Structured Public Involvement (SPI) is a developed protocol for involving communities in project planning decisions and could be readily applied to the blasting industry. SPI was developed for the purpose of collecting quality public input about public transportation projects. The purpose of SPI is to bring about stakeholder satisfaction with potential projects by allowing controlled input from the stakeholders. It was designed and intended for democratic societies that have come to expect a voice in public projects. While blasting operations are not always in the domain of public projects, the fundamental process outlined by SPI can be useful for collecting feedback from the immediate public around blasting operations.

Jan 1, 2014

By Ken-ichiro Uemura

"The DIOS process has been developed for eight years since 1988. The research project was started with the element studies carried out by each of the five integrated steel making companies in Japan, the final two and half years were spent for the pilot plant studies. Operation were conducted in the entirely closed and pressurized system successfully as planned. From the result, the DIOS process was proved to be viable as a future iron-making process substitutable for the conventional blast furnace. In addition, a lot of findings were obtained. Hot metal productivity was primarily determined by a oxygen flow rate, and a coal consumption varied depending on the productivity. The post combustion ratio was a little lower than expected from the result of the element study. It was supposed to relate the gas-reforming with coal or volatile matter in the free space of the furnace. Hot metal carbon content seemed to depend on the char content in slag.INTRODUCTIONThe JISF's DIOS pilot plant (DIOS=Direct Iron Ore Smelting Reduction Process) has finished its last campaign of the operations in January 1996. The project was started in 1988 as a joint research of the Center for Coal Utilization, Japan and the Japan Iron and Steel Federation (JISF) with a subsidy for promoting coal productions and utilization technologies from the Agency of National Resources and Energy, the Ministry of International Trade and Industry(MITI). Throughout the pilot plant test, a total of over 20,000 tons of hot metal was produced for more than 2,000 hours of the operation. Recorded production rate was 538 ton/day for 3 days at a specific coal consumption of approx. 1,000kg/hmt. Long-term operation was carried out in the fifth campaign for 18 days, which has proved that the entirely closed and pressurized DIOS process works well as planned. In Figure 1 is shown the representative operational performance obtained in the first five campaigns. The project is going to be finished by the end of March this year after investigating the technical viability and economic potential of the process, and completing the conceptual design of the DIOS commercial plant. In this paper, the system and facilities of the DIOS process are first introduced and some of the results of the pilot plant test are detailed later."

Jan 1, 1996

By Abbas Zaidi, Betty L. W. Ou

Wastewaters generated during the extraction of gold from the ore can contain a variety of contaminants such as cyanide, heavy metals and arsenic. Proper management of these wastewaters is therefore necessary to minimize the negative impact of gold mining and milling operations on the environment. The Wastewater Technology Centre (WTC),located in Burlington, Ontario, Canada, has been involved in several studies related to the evaluation of various effluent treatment technologies which are relevant to the treatment and proper management of gold mill effluents. These studies have included bench and pilot scale tests, and the evaluation offull-scale systems. Furthermore, the WTC staff developed protocols for cyanide analysis in gold mill effluents, and a mathematical model for predicting the degradation of cyanide in tailings ponds. The information generated by the WTC staff has been referenced in several reports and papers published over the last ten years (Schmidt et.al. 1982, Simovic & Snodgrass 1989, Whittle et.al. 1989, Zaidi et.al. 1989, Zaidi et.al. 1991). Recently, the WTC has started to develop a micro­computer based expert system for use by decision makers in the gold mining industry and relevant government agencies who are involved in process design, process evaluation, costing, evaluation of the best practicable technology, approval of suggested effluent management systems, and so on. This paper presents some relevant background information and a discussion of the latest version of the expert system being developed by the WTC.

Jan 1, 1992

By John Hall

SOME months ago one of the authors was asked to write a paper on the heat treatment of steel castings that would be more comprehensive than other matter lie had published; this is an attempt to present in condensed form the results of experimental work and actual practice carried out for the most part in 1907, 1908; and 1909. It is not a laboratory research and the work done was carried out for the express purpose of putting in practice the processes discovered as fast as possible. Most of the tests are the result of commercial practice and not of bars annealed in our laboratory; most of the micrographs were made for our own records and not for publication. Certain of the micrographs, therefore, are not as clear as we may wish but they were good enough for our purpose at the time they were made. The tests and micrographs are selected from several thousands in our files. All of these micrographs are magnified 60 diameters. These experiments were conducted almost entirely on steel made in a 3-ton bottom-blown converter, and most of the steel illustrated analyzes about 0.05 in phosphorus and sulfur. Unfortunately, a certain number of specimens are shown of which we do not have the complete analysis, but in most cases in which the phosphorus and sulfur vary much from the figure just given that fact is noted. For purposes of comparison, we have included a certain number of micrographs and tests of steel made in the electric furnace, some of which were from specimens made in other shops and some in our own shop, and some tests of acid open-hearth and tropenas steel.

Jan 9, 1919

By Marvin B. Thompson

"The depositional model for major Illinois Basin coalbeds is well documented and defined on a regional scale. The model was a driving force during past exploration for lower sulfur and thicker coal deposits. The most attractive coal reserves were known to lie along the flanks of contemporaneous sandstone filled stream channels and were overlain by thick silty gray shale roof. At various distances away from the channels, the depositional model transitioned to black shale I limestone roof, sulfur content of the coal bed increased, and the coal bed often thinned. Understanding the character of roof rock types associated with this depositional model is essential to predicting ground control factors on both a regional scale, and on resolving roof control problems at the mine-site. Additionally, horizontal stress and overburden depth are significant factors that impact roof rock quality and ground control in Illinois Basin mines.Determining the character of several rock types, and defining the primary horizontal stress direction were crucial to a recent successful project at New Future Mine, located in southern Illinois. An inclined slope was constructed from the Illinois No. 5 Coalbed up to the Illinois No. 6 Coalbed through strata that ranged from extremely weak ""stackrock"" and a weak underclay unit, to a massive sandstone unit. Engineering geology, operations management, and Jennmar technical services personnel teamedup to select and install roof support for each strata transition. The project was completed with no injuries and no roof falls.INTRODUCTIONAbundant published information concerning coal deposition, geographic distribution, quantity, quality, and mining conditions exists for Illinois Basin coal reserves. The State of Illinois, through its State Geological Survey (ISGS), has provided decades of research, record keeping, and service to the coal industry. Other excellent sources of Illinois Basin coal information include the Indiana Geologiq1l Survey and the Kentucky Geological Survey. Past research by the U.S. Bureau of Mines (USBM) supplemented the work by the geological surveys, especially in the area of horizontal stress and mining hazards. The National Institute for Occupational Safety and Health (NIOSH) continues to produce publications focused on roof control issues common to many coal basins, including the Illinois Basin. Many of the illustrations in this paper originated in ISGS and USBM publications."

Jan 1, 2010

By Z. Zborovszky

The feasibility of using the nucleation properties of combustion generated particulates for the identification of their sources was investigated, using the Cloud Condensation Nuclei (CCN) Spectrometer. The Investigated materials included coal, wood, belt materials, electrical insulation, brattice cloth, and diesel exhaust. The materials were heated In an oven using filtered air flow, and their time, temperature, and the critical supersaturation spectrum of condensation nuclei (also referred to as the CCN spectrum) produced by the combusting material were recorded. Some data was obtained on a typical metal-mine background containing blasting products. The data was processed and analyzed In an attempt to specify parameters and limits that would allow the identification of the combustion sources. It appears that under controlled test conditions It Is possible to Identify the source on the basis of data derived from the CCN spectrum. More general use of the Idea for fire detection under uncontrolled practical circumstances in an actual mining environment does have potential but would require further research.

Jan 1, 1978

By Audrey Wagenaar

Introduction ?? Rising public pressures are being placed on companies worldwide to protect the environment and the health and safety of their workers and local communities. ?? International bodies and shareholders want to make sure developments and companies can meet internationally acceptable standards for EHS. In 2005, Golder Associates was asked by the IFC to conduct a comprehensive review and update for their Environmental Health & Safety Guidelines including the mining sector.

May 1, 2008

By B. T. McKenna, H. Nirschl, P. Morsch, B. Fränkle

Generally, filter media used in filter presses have a limited operational life. Besides mechanical damage, there is a growing deposition of fine particles with increasing filtration cycles, the so-called blinding, inside the filter cloth. The resulting decreasing pore diameters not only affect the efficiency of the filtration process itself by increasing the filter medium resistance, but also make it more difficult to regenerate the filter press between the individual cycles, e.g. leading to an insufficient cake discharge. Since tailings filtration requires handling of large process flows containing a significant fraction of particles in the lower micrometer range, an investigation into media rejuvenation is of interest. Keywords: Tailings filtration, filter fabric resistance, filter media regeneration, filter cleaning, intraweave contamination

Jan 1, 2020

By Chris Harris, Kamal Adham

The use of HCl acid is gaining momentum among hydrometallurgical processes. However, the issue of environmentally efficient and economically viable ways to regenerate HCl acid (from various metal chloride intermediate products) remains a technology and operational challenge. The authors provide a state-of-technology review based on Hatch’s years of testing, design and commissioning experience with high-temperature units (fluid bed and spray roasters), plus the recent efforts in the area of low-temperature HCl regeneration.

Jan 1, 2014

By Silver EA

The Finisterre Range on the north coast of Papua New Guinea is the uplifted forearc riagio.n. of a modern arc-continent collision. The core of the range is composed of the P- nisterre Volcanics, an Oligocene''-arc terrane. The southern flank of the range consists of a clastic sedimentary sequence which is an uplifted accretionary wedge and collision complex. This clastic sequence can be subdivided into three distinct units. To the south of aiid structurally below the Finisterre Valcanics are the Mebu beds, an Oligocene- $arly Miocene sequence of volcanolithic turbidites. The Erap Structural Complex is south of, and structurally below the Mebu 43eds. , It consists of three subunits; the 3rly Pliocene micaceous turbidites of the Sukurum unit, contemporaneous pillow basalts AF{ the Basalt unit, and Late Pliocene to Pleistocene volcanolithic turbidites of the -Nariawang unit. The Quaternary Leron Formation, a fluvial to shallow marine 'clastic unit, is the southernmdst. and structurally lowest unit of the clastic -sequence The Finisterre Range is dominated by a fold-and-thrust belt with most thrusts "dipping steeply N. Melange fabric _ is developed in the vicinity of major thrusts. "ffle thrust belt strikes NW, oblique to the regional convergence direction, but no strike-slip motion is observed along NW striking faults.

Jan 1, 1991

By Q. X. Yun

This paper presents a new approach to optimize the transportation system in open-pit mines. The new approach employs artificial intelligence, fuzzy sets, dynamic programming and CAD technique to determine the transportation system. The determination consists of 4 phases: initial selection, road alignment, final decision .and open-pit drawing.

Jan 1, 1992

By S. K. Shaha, A. Gryguc, S. B. Behravesh, B. Williams, M. Wells, H. Jahed

Warm forging to near final product geometry shows promising benefits in terms of microstructure refinement and texture modification. In the present study, Semi-closed die forging was performed on extruded AZ80 magnesium alloy at a forging temperature of 400 °C and various forging ram speeds. Compression tests were performed to investigate the influence of forging at various deformation rates on the performance of extruded AZ80 magnesium alloy. The microstructural analysis showed that the extruded AZ80 possesses a grain structure typical in wrought magnesium alloys, with sharp basal texture. In contrast, the forged samples had a recrystallized microstructures and a spatially varying textures and crystal orientations resulting from the complex flow behaviour within the closed die forging. Furthermore, once forged, a significant increase in the material isotropy, homogeneity as well as failure elongation were observed. An increase in UCS of 9% was observed in the forging direction, while the UCS in the extrusion direction was similar to that before forging. The changes in UCS can be attributed to both the refined grain microstructure and crystal reorientation. Successful microstructure recrystallization occurs for strain rates which traverse several orders of magnitude, and in general, UCS isotropy increases with increasing strain rate. It is believed that forging cause’s grain refinement and texture modification which act to enhance the mechanical performance (UCS, fracture strain and superficial hardness) for the forging conditions investigated in this study.

Mar 1, 2017

By J. Gniel, L. King, C. Gaudin, C. O’Loughlin

"This paper presents some recent advancements in centrifuge modelling, which enable the installation of displacement piles to be performed in-flight while measuring ground responses. Details and results are provided from a series of experiments where 21 full-displacement piles were installed into a sample of consolidated kaolin clay at 40g. The piles were pushed into the sample at a constant rate of penetration, with installation reaction loads and pore pressures measured. Insight into the installation effects of the full-displacement piles was obtained by undertaking in-situ testing pre- and postinstallation of piles. The findings show that centrifuge testing has the potential to play an important role in furthering the current understanding of displacement pile behaviour and installation effects.INTRODUCTIONDisplacement piles and displacement ground improvement columns cause soil to undergo significant distortion and shearing during installation, which alters the soil properties. It is essential to consider these changes in soil properties to estimate the behaviour of pile foundations with higher degree of accuracy. However, the installation effects of displacement piles are widely considered as one of the most difficult geotechnical mechanisms to model, both analytically and numerically, and experimental data is needed to advance the current state of knowledge.Theories, analytical and semi-analytical, have been developed to describe the displacement pile installation process. Randolph et al. (1979) applied the cylindrical Cavity Expansion Method (CEM) to model the installation of a displacement pile in a fine grained cohesive soil. However, cylindrical CEM only considers the field variables in radial coordinates, and hence the soil-pile interface can only be modelled as a frictionless material. Baligh (1985) introduced the Strain Path Method (SPM), which assumes soil flows around the tip of a displacement pile. SPM was shown to model the stress and strain fields, particularly within close proximity to the pile, more accurately compared to the cylindrical CEM. While these methods account for the installation effects of a displacement pile and can be used to estimate a resulting ultimate bearing capacity, they are unable to describe the load-settlement behaviour of such piles. With the added complexity of group effects, existing analytical methods do not provide a means to accurately calculate the ground response to the installation of a group of displacement piles in a cohesive soil.The advancement of computational power, numerical techniques and constitutive models has improved the accuracy of numerical analysis, particularly in regard to modelling pile installation. However, even with advanced techniques, Finite Element Method (FEM) suffers a number of disadvantages due to the large deformations, which results in mesh distortion and tangling. Mesh-free methods such as Discrete Element Method (DEM), Smoothed Particle Hydrodynamics (SPH) and Material Point Method (MPM) are the next generation of computational techniques that are able to deal with large deformation problems. However, these advanced techniques are computationally expensive, complex and yet to be incorporated into commercial packages. Such methods are considered to still be in the development stage and are yet to provide a complete solution to pile installation problems."

Jan 1, 1900

By F. W. C. Boswell, R. L. Cunningham, H. M. Weld

Chemical analysis shows the partition of the magnesium addition between the metal and the graphite is independent of whether the graphite is in the form of nodules or flakes. The bright central spot observed in nodular graphite polished sections is shown to be due to the structure of the nodules. DURING the past few years numerous papers have been published on the production1-7 and heat treatment" of nodular cast irons. However, very little information is available on the structure of the nodules and the reason for their formation. It would appear that an explanation of the phenomenon of nodulation must await a detailed knowledge of the nature of the nodule. Disagreement exists among various workers on such a fundamental point as to whether or not a nodule actually contains a microscopically visible, nongraphitic nucleus.9-11 Work was initiated with a view to obtaining definite information on this and other aspects of the problem. Chemical Separation and Analysis Microscopic appearance had indicated9-11 that a nongraphitic core might exist in nodules (Fig. 1). It appeared that a chemical comparison of separated nodules and flake graphite would be profitable, for if the core is nongraphitic a relatively large amount of certain elements would be found in the nodules as compared to the flake. This comparison could best be made by obtaining nodules and flake from the same melt of cast iron, part of which had been in-noculated with a suitable addition reagent for the formation of nodules. A 300 lb melt was produced. About half of this was innoculated in the ladle with an Fe-Si-Mg alloy to produce nodules and cast into keel blocks; the remaining half of the melt had silicon added in an effort to compensate for the silicon in the innoculant used in the other half of the melt and this was cast into similar keel blocks. The analyses of the resultant irons are given in Table I. Nodules and flake were chemically extracted from 2 kg samples of metal as described in the appendix. While this method dissolved the iron and chromium carbides, it did not dissolve the titanium, vanadium, and molybdenum carbides. These latter carbides could have been removed by nitric acid, but in other experiments it was found that it attacked pools of metallic iron entrapped in the nodules which had, until the nitric acid treatment, been protected from the attack of the sulphuric, hydrochloric, and hydrofluoric acids. It will be shown in the next section that entrapped iron exists in nodules but not in flake. On microscopic examination many tiny irregular particles were observed to accompany both the nodules and the flake. These were identified by tabling a sample of nodules from which a sufficient fraction was obtained for X-ray analysis. A good pattern of titanium carbide was obtained indicating that this was the predominant compound present. Since it was not possible to determine how completely the carbides could be removed mechanically and since their removal from flake is much more difficult, it was decided not to resort to any separation as this would render further comparisons more difficult. The samples were ashed in a combustion

Jan 1, 1953

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

Jan 1, 2006

By Ruiling DU, Xiao YUAN, Keng Wu, Daan XU, Changyao CHAO

To utilize low grade coals to produce high quality semi-coke which can be used in blast furnaces, the pyrolysis of low grade coals was studied in this paper. According to the characteristics of coal pyrolysis process, the temperature range was divided into three parts. The interfacial chemical reaction model, random pore model and the internal diffusion model with the shrinking volume of resultant were established to describe the different ranges of pyrolysis process respectively. The results showed that the experimental data was fitted well, and all the correlation coefficients (r2) exceeded 0.97. Finally, the kinetic parameters for each temperature range have been calculated, which laid a necessary foundation for the simulation and expanded production.

Jan 1, 2016

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By Oswald J. Heinrich

THE great improvements which have been made in late years in the different systems and instruments used to perforate the crust of the earth for purposes of testing and exploring for mineral resources or for other reasons, by means of bore-holes of greater or less diameter and to greater or less depths, are manifold. It may therefore be of interest to make an impartial comparison of them, or of such as are most commonly used. Being well aware of the difficulties which are encountered in such a task, a reasonable allowance must be made in such a comparison. It is a rare instance when even two decidedly different systems or instruments have been used in the same locality, penetrating identically the same strata to the same depth. The diameter of a borehole as well as its greater or less depth must also be considered in regard to its cost per foot, etc. But for practical purposes, for ex¬ploration at least, we may assert this rule Any borehole, of whatever diameter, which allows the means of examining the strata most carefully and completely, will be sufficient for this purpose, but that one which will do it most economically and in the least space of time, must be considered the best for it. It will, therefore, partially depend upon circumstances, what system, in spite of other superiorities, may be the best in each case, and the following remarks may aid in deciding this question. To make the attempt here to review all that has been published upon the different systems and means of boring would be out of place. Reference can be had to the able publications treating upon this subject. A difference in this respect exists in regard to the use of the hollow rods in connection with the diamond drill, used for that purpose. The great future, which appears to be evident for this instrument, will be warrant enough for any one, who has had the opportunity to test it, to give his experience to the public. Only in this way can we bring this system to such perfection, as it seems to deserve and * The drawings illustrating this paper are one-half the size of the tools represented, with the exception of the instrument used to reverse the current in the bore-hole (Fig. 17), which is one-third the actual size.

Jan 1, 1874

By R. L. Veenstra

This paper explores the connection between the stresses observed and the failure mechanisms present in the modelled cemented paste backfill. In order to look at this connection, the authors have used a previously developed model to conduct a sensitivity analysis of the model?s strength and permeability input parameters. The results from the sensitivity analysis were then compared to determine what causes modelled stresses and failure mechanisms to vary. Increased insight into the behaviour of the modelled paste will help clarify how paste behaves in the field.

Aug 1, 2013

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998