Search Documents

By Eric J. Pederson

The down hole hammer is widely used in specialty geotechnical construction. The common uses include tie-back anchor installation, micropile installation, and general soil/bedrock drilling operations. Veit used these techniques to develop a cost effective way of installing the foundation system for University of Minnesota Football Stadium. The soils present at the site of the stadium contained layers of concentrated cobbles and boulders. The geotechnical engineer recommended a driven pile system, and the base bid outlined in the project documents consisted of an H-Pile using a 14x73 pile section. Veit submitted an innovative alternate consisting of using a rotary percussion system to install a 12? O.D. pile. This paper will show that this pile type and installation method was the correct choice for the project. The design criteria for the compression, uplift, and lateral capacities and deflections were met, while eliminating pile damage. The method resulted in a significant cost savings to the University and maintained the project schedule.

Jan 1, 2008

By Thomas O. Glover

History of Underground Coal Mining in Illinois The production of coal in Illinois using underground mining methods, commenced early in the 1800's; however, the first shaft entrance was not sunk until 1842. The shafts range in depth from 16 feet (4.9 m) in Peoria County to 1,001 feet (306 m) in Christian County. The earlier mines were smell, private operations that worked outcrops and shallow seams at less than 100 feet (30.5 m) in depth. By 1975, there were reported 4,076 abandoned underground coal mines in 70 Illinois counties (Nawrot, 1977). There were many more mines; however, only 4,076 underground mines have been documented. Small mining operations characterize the majority of the underground mines. There have been no significant multiple seam operations in Illinois. The most extensively mined seams were the number two, five, and six seams. Number two seam was worked in the early 1900's by 252 mines in the longwall mining region of northern Illinois (Nawrot, 1977). Available records for 2,054 abandoned mines identify 1,043 as shaft nines, 700 as slope mines, and 311 as drift mines. Some operators began reporting annually to the State Department of Labor in 1879 and by 1882 all mine operators were reporting. Annual reporting still continues to date. The information is compiled by the State Department of Panes and Minerals in their "Annual Coal Report." By the end of 1974 there were 800,000 acres (323,756 hectares) of abandoned underground coal mine workings (Smith-Stall, 1975)2 Copies of abandoned underground coal mine maps may be inspected by interested parties in the State Department of fines and Minerals office in Springfield, Illinois, or at the office of any county recorder for mines within their county. Copies of active underground coal mine maps may be inspected at a State mine rescue station near the mine site or at the county recorder's in the county in which the mine is located. Copies of active underground coal nine naps shall be open to the examination of all interested persons, but such examination shall be made only in the presence of the State mane inspector or the recorder. At the present time, the Department of Mines and Minerals has 1,746 maps of abandoned underground coal mines in its possession. These maps cover the majority of

Jan 1, 1977

By O. Lashkari, A. Charette, R. Ghomashchi

Conventional casting at low pouring temperature was employed to produce semisolid metal, SSM, billets of A356 Alloy. The deformation behavior of the as-cast SSM billets was studied using parallel plate compression viscometry. The compression tests were carried out at different applied pressures, and fractions solid. The rheological studies were conducted assuming the SSM slurry behaving like Newtonian and non Newtonian fluids respectively. The calculated viscosity numbers confirmed pseudoplastic behavior of the SSM billets and were correlated to fraction solid and shear rate proposing the following empirical equation which is valid at low shear rates, less than 0.01 s-1, and fraction solid of0.33-0.46: 0 log77 =5.56-l.38fs -(l.56fs +0.14)logy Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by G. Dufour, F. Paray and J. Tessier 0.33<fs<0.46

Jan 1, 2006

By J. F. T. Agapito

Experience at Energy West Mines in the Wasatch Plateau Coal Field, Utah, has shown that longwall face bursts occur mostly near the tailgate when extracting the third adjacent longwall in a panel section where depths exceed 610 m (2000 ft). It is believed that this is due to a combination of cover depth and side abutment stresses created by the widening of a pressure arch formed by interlocking and bridging of large blocks of" very competent strata. The 60-m-thick (200 ft) Castlegate Sandstone probably plays a key role in pressure arching. This paper presents a back-analysis of the location and magnitude of the stresses associated with face bursts that occurred when mining the 7th Right Longwall at the Deer Creek Mine. Improvement of these conditions may be achieved by widening the longwalls to attain critical subsidence width sooner while mining the second long-wall, and to reduce stresses at the face. Wider longwall faces, however, increase the chance of sandstone channel interception often associated with bursts. Satisfactory mitigation of face bursts beyond cover depths of 610 to 670 m (2000 to 2200 ft) may be difficult without using destressing techniques. The hydraulic fracturing/liquid infusion technique seems to offer the best possibilities for application in longwall mining.

Jan 1, 1997

By Manuel Gomez

A lignite from Milam County, Tex., has been oxidized by air at temperatures from about 27° to 300° C. for varying lengths of time. The oxidized coal was carbonized at 500° C. in a laboratory assay unit, and the products of carbonization were measured and analyzed. The data presented suggest that, as lignite is progressively oxidized, tar yields are decreased and gas yields are increased in a ratio approximating 1:1. It is surmised that tar-yielding structures in the nonoxidized coal produce gas, principally, when the coal is oxidized. Char-yielding structures of the nonoxidized coal give rise to additional water of decomposition after oxidation and pyrolysis. As lignite is subjected to greater oxidation, the gaseous product evolved on pyrolysis becomes almost entirely carbon dioxide. Tar yields decrease with an increased degree of oxidation, so that the reduction in tar yield may be used as a qualitative measure of oxidation. Pilot-plant drying and carbonization, where air is used as the transport gas and where some air is included in the drying and carbonizing gases, induces some oxidation of the coal particle. The short residence time in a fluidized system with reference to the oxidation environment limits the oxidation.

Jan 1, 1956

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By AIME AIME

A CERTAIN area in the State of Indiana seems to be a breeding place for presidents and near president about eighteen miles southeast of Elwood is the little village of Daleville, and there, on April 9, 1890, John Robert Suman, newly elected President of the A.I.M.E., was born. It was not long before he migrated to California, however, where he went to the Los Angeles High School, then for two years to the University of Southern California, after which he went up to Berkeley

Jan 1, 1940

Consolidated Rutile Limited (CRL) was one of the best performing mining stocks of the turbulent 1980s, having a very high payout of franked dividends. In contrast to some other mining groups, it was not highly involved in the speculative lead-up to the 1987 sharemarket crash. Its base was firmly laid through a succession of decisions that were taken in the period 1982-1985. These decisions and the rationale behind them are outlined in this paper. CRL began the 1980s in a highly favourable position. It had successfully pioneered the transition to high-throughput mining of the high dunes on North Stradbroke Island (NSI), commissioning its 2100 tph cutter suction dredge at the Bayside reserves in 1978 at the time of rising prices, such that it was able to pay off its modest bank loan within 18 months. The June 1980 results showed a record after-tax profit of $5.6M, from total assets fo $26.5M and sales tonnages of rutile and zircon of around 50,000 tonnes each.

Jan 1, 1991

By Michael W. Oakland

This paper summarizes the analysis and design of a pile foundation system for two 400 ft. diameter, 500 ft. high cooling tower using a detailed finite element analysis package. The cooling towers are at the Brayton Point Power Plant in Somerset, Massachusetts. The design-build project will convert the power plant to a closed loop cooling system to reduce return of heated water to the bay. Each cooling tower is supported on a 5 ft. thick by 16 ft. wide ring beam with 44 columns oriented in a radial pattern. The allowable lateral movement on the thin wall shell was limited to only 0.5 inches. Lateral and tension resistance were the primary concerns for the large, but lightweight structure and the critical issue was the lateral response of piles and pile groups within the system. By constructing a detailed model of the foundation system including modeling each pile as an independent element, the contribution of each element was separately assessed and the system tuned to take best advantage of the load distribution afforded by the ring beam as well as the soil structure interaction created by tangential as well as radial resistance of the pile groups. The detailed model also incorporated the lateral resistance of interior piles supporting an equipment slab within the ring beam. Simpler models analyzed the pile groups independent of the complete structure and generally only relied on radial stiffness and generally resulted in large groups of piles needed at each pier. Through a series of trial configurations, the number of piles used was optimized. Confirmatory lateral, vertical and tension load tests were conducted and final fine tuning of the model completed.

Jan 1, 2010

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The effects of increasing hydrogen content, introducing a notch, and changing the strain rate on properties of titanium and one of its alloys were investigated over a range of testing temperatures from —196° to 200°C. Both high purity and commercial purity A-55 titanium were used as representative a materials, while a commercial Ti-8 pct Mn alloy was used for an a-P alloy. It was found possible to analyze the data, using the ductile-to-brittle transition temperature concept. Increasing hydrogen, the presence of a notch, and increasing the testing speed raised the transition temperature for the a materials. The presence of hydrogen and notches raised the transition temperature of the a-B alloy also. However, increasing the testing speed generally decreased the transition temperature of the a-p alloy. IN previous papers, the authors have shown that hydrogen is most detrimental to the notch-bend impact toughness of a-titanium&apos; and to the tensile ductility of a-B titanium alloys.&apos; These general effects have been confirmed by Kessler and co-workers," and by Kotfila and Erbin." Kessler showed that the slower strain rate in notch-rupture tests was a more sensitive measure of hydrogen embrittle-ment of a-B alloys than the tensile test. In the present paper the authors cover, with tensile and notch-bend tests, the effect of testing speed, notches, and testing temperature on hydrogen em-brittlement. High purity and commercial purity titanium, examples of u materials, and a commercial a-,f3 Ti-8 pct Mn alloy were investigated. The purpose of the investigation was to correlate the factors producing embrittlement. Materials The high purity titanium for this investigation was obtained by arc-melting crystal bar from Foote Mineral Co. into 1 Ib ingots. As-cast hardnesses for these ingots ranged from 60 to 90 Brinell. The arc-melted ingots were forged to % in. diam rods at 1470°F. These rods were swaged to & in. diam at room temperature prior to machining of the specimens for hydrogenation and testing. The commercial A-55 titanium and the Ti-8 pct Mn alloy were obtained from Rem-Cru Titanium Inc., as % in. diam rod. The A-55 titanium was hot swaged to 1/4 in. diam at 1300°F prior to machining of the specimens for hydrogenation and testing. The a-p C-11OM alloy was hydrogenated prior to hot swaging to 1/4 in. roc1 at 1300°F. Hydrogenation prior to fabrication permitted testing of the a-P alloy in the equilibrated and stabilized condition. The equilibration and stabilization treatment used was an air anneal for 1 hr at 1300°F, followed by furnace cooling to 1100°F and then air cooling. Hydrogenation was done in a Sieverts apparatus described previously.&apos; The hydrogenation treatment consisted of heating for 1/4 to 1/2 hr at 820 °C in purified hydrogen, slow cooling to 680"C, holding 1 hr for homogenization, and rapid cooling to room temperature. Intended hydrogen levels for the a-tita-nium materials were 0.05, 0.5, 1.0, 1.5, and 2.0 atomic pct—about 15 to 430 ppm. For the Ti-8 pct Mn alloy, the intended hydrogen levels were 0.05, 0.5, 1.0, 2.5, and 5.0 atomic pct—about 15 to 1100 ppm. The material for the 0.5 atomic pct level of hydrogen was vacuum annealed prior to hydrogenation to increase the accuracy of the addition. Vacuum annealing to remove hydrogen consisted of heating for 6 hr at 820°C, and resulted in a hydrogen content of about 10 to 15 ppm. When hydrogen contents were above 0.5 atomic pct—100 ppm—the hydrogen was added without prior vacuum annealing.

Jan 1, 1957

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale), Condition C (Rolling Sandstone with Shale in Pockets) and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were used to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 1, 1978

By André L. de Vegt

Soil and groundwater beneath a zinc production plant in The Netherlands are contaminated with metals and sulfate. To avoid contamination of nearby drinking water aquifers, a hydro-geological containment system and a biological treatment plant for the extracted ground water have been installed. Currently about 5000 m3/day of groundwater is extracted from a combination of 12 shallow and deep wells. Heavy metals and sulfate have to be removed from the extracted water before it can be discharged into a river. Several water treatment methods have been studied and pilot tested at the site. The preferred and selected process is based on the activity of sulfate reducing bacteria (SRB) and combines sulfate removal and heavy metal removal in one single installation. Anaerobic bacteria reduce sulfate to sulfide resulting in the precipitation of metal sulfides. Excess sulfide Is biologically converted to elemental sulfur. A full scale biological treatment system was started up in May 1992. Design, start-up, commissioning and operational experiences are reported in this paper. Concentrations of metals and sulfate in the SRB water treatment plant effluent are well within the limits set by the Dutch Authorities for discharge to surface water.

Jan 1, 1995

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By Xiaoting Li, Richard Adasiak, Benjamin Mirabile

Pumpable J-Crib stopping walls and Jennmar high-strength (HS) stopping panel walls are widely used for resisting high-ventilation air pressures and roof support in underground mines due to their installation efficiency, convergence allowance, and better performance than traditional concrete block stopping walls. Based on the different entry dimensions and required maximum ventilation air pressures of up to 36-in. water gauge, 24-, 27-, 30-, and 36-in.-diameter pumpable J-Crib stopping walls, or 18- to 30-in. thick Jennmar HS stopping panel walls can be designed, and their support capacities and convergence allowances are evaluated for better roof control. Pumpable J-Crib stopping walls consist of 0.187-in.-diameter steel wire reinforced, JCrib material-filled bags, and non-wire-reinforced filler bags in between. Jennmar HS stopping panel walls consist of two, 20-gauge (0.04-in.-thick), galvanized, cold-formed steel panels with J-Seal materials pumped in between. Based on the fundamental structural design principles and specifications of ACI 318-19(22), the compression and flexural strength, and shear resistance of the walls can be checked to be compliant with the codes and specifications following the load and resistance factor design (LRFD) method. Specifically, the 0.187- in.-diameter steel wires in the pumpable J-Crib walls and 20-gauge steel panels in the HS stopping walls are integral parts of the walls and are considered to effectively confine the J-Crib or J-Seal materials. These steel elements play a significant role in reinforcing and improving the strength or support capacity of the stopping walls from a structural design perspective. Because of the high ductility of low-density J-Crib/J-Seal materials and steel elements, these walls are good at accommodating or absorbing the roof convergence (≥5% entry height), which cannot be matched by a traditional concrete block stopping wall (Figure 1). Based on the successful design and application of these stopping walls in different mines for improving roof stability and avoiding the air leakage, the authors have formulated the design methodology and verified independently by the finite element analysis (FEA) simulation technique. This design methodology combines the fundamental structural design principles with specific wall dimensions and material properties, facilitating mine engineers and government agencies to understand the in-depth working mechanism of these stopping walls.

Jul 1, 2023

By Charles H. Atkinson, Robert T. Johansen

Tremendous volumes of petroleum ( crude oil and natural gas ) at present cannot be recovered economically . The feasibility of using nuclear explosions for production stimulation therefore has been investigated . Data from underground nuclear tests conducted by the Atomic Energy Commission were reviewed , and the physical effects were evaluated for stimulating petroleum production . Calculations of the effect on ultimate recovery of increasing reservoir temperature with nuclear explosives showed disappointingly small increases . Production increases caused by fracturing of massive low- permeability reservoirs appear technically and economically promising . Petroleum reservoirs that might be converted from submarginal to commercial production are being located and evaluated as to potential reserves and as a location for a field test .

Jan 1, 1964

By Wilfred Walker

Much is known of the geography of the Alpine orogeny because it has now ended and all geosynclines are in their terminal, cordilleran form. The principle of sea floor spreading, continental drift, and mantle cells has gained general acceptance, but the number and position of the cells, even during the Alpine orogeny, is controversial. The oceanographers have demonstrated the uprises and in this paper it is suggested that downflows are marked by island arcs in the oceans and geosynclines (now cordillera) in the continents, for a total of about a dozen cells. Major mineral deposits associated-with the Alpine downflows are porphyry copper, molybdenum, nickel, chrome, lead-zinc-silver, gold, mercury, tungsten, and tin. Amore precise environment is known for some of these metals, for example, nickel, chrome, and mercury in flysch (which flanks mantle downturns), Ten major orogenies have taken place from 3500 m.y. to the present, Their re¬construction and metallogenesis is the subject of a continuing study.

Jan 1, 1971

By O. E. Brown

The measurement principle of the Coulter Counter for particle size analyses is described. The application of the Coulter Counter to cement particle content and size analysis and to the size distribution of clinker from standard grindability tests are described. Methods of calibration, sample preparation and data reduction are presented. The results of the analyses obtained are compared with characteristics associated with performance showing both concordance and non-concordance of test data., Future uses of the Coulter Counter for particle size analysis in research and plant control adaptations are indicated.

Jan 1, 1960

By F. W. Wellmer

"I would like to comment on the classification scheme of ore reserves based on geestatistical and economic parameters as proposed by Wober and Morgan in the CIM Bulletin, January 1993.In principle, a classification system that combines quantitative data for levels of confidence and errors with economic expectations must be welcomed. I would like to point out, however, two aspects of the proposed classification system which might create ambiguities, and therefore problems, by working with two levels of confidence and two kinds of block sizes. A normal classification scheme reflects the information density, the highest reserve category such as class A, or proven, or measured reserves having the highest density. This is not necessarily the case in the scheme of Wober and Morgan (1993), unless the definitions are amended.I. Assuming, as the authors do, that the estimation errors show an approximately normal clistribution, at the 95% confidence level, the standard deviation has to be multiplied by about 2 for the error and, at the 84% confidence level by about 104. Reserves (or resources) with the same or even higher information density than class A reserves, which at the 95% confidence level would not fulfill the required economic criteria at the threshold level, i.e. not qualify as ""ore"" at all, could be retained ""on paper"" to class B reserves by just multiplying the standard deviation by the factor 104 instead of 2, thereby narrowing the error.This statistical ambiguity was partly inherent in the old German classification scheme which used varying confidence levels and errors (GDMB 1956; Jahns 1959). In the new German scheme, which was later adopted in Austria in a moclified version, the level of confidence was therefore fixed at 90070 for all reserve categories (Wellmer 1983; ONORM 1989)."

Jan 1, 1993

By T. F. Torries

Market data commonly perceived as being useful to industry for decision making include prices, production and trade quantities, production and transportation costs, stocks, customer&apos;s needs, and competitor&apos;s qualifications. Costs and factors affecting costs are particularly important in determining competitive positions and possible future prices. These costs include relative cost of production as well as cost experienced by the buyer in making the final product. Care must be taken to calculate costs in a consistent manner to achieve meaningful analyses.

Jan 1, 1987

By C. K. Kocsis

A study was undertaken to evaluate the thermal environment and determine the contributing heat sources within the existing 153 Orebody of Coleman/McCreedy East Mine which would then enable the prediction of the climatic conditions in the mine?s future 170 Orebody. The study entailed continuously monitoring, for a 2-week period, the dry-bulb temperature, humidity and barometric pressure along the existing intake airways from surface down to the 4810 Level and throughout an active mining area on that level. Furthermore, the mining activities and associated equipment that could be responsible for any changes in the temperature and humidity conditions within this mining area were also monitored. These data were then used to develop and validate a climatic simulation of the mine?s mechanized cut and fill mining method. This climatic model was then transposed to the future 5700 Level in the deeper 170 Orebody, to determine the environmental conditions within its production workings and along the main haulage route ascending from that area. Based upon the simulations performed it was shown that the level of ventilation planned for the new orebody should be able to maintain adequate environmental conditions. However, this study did emphasize the importance of the appropriate distribution of airflow in workplaces that used auxiliary ventilation in order to sustain a suitable thermal environment.

Jan 1, 2009