Search Documents

By H. R. MacMichael

IN the Chihuahua district of Mexico the first smelting was that inaugurated by the early Spaniards for the production of silver bullion. The ores treated were high in silver and lead. Silver-lead bullion was first produced and the lead then cupelled to waste, with the slag produced running from 5 to 10 per cent in lead and about 25 to 40 per cent silica. The ore was mined by peon labor, often being carried out of the mine on the backs of the men, and then transported by burros. Furnaces were of primitive construction, adobe or rock being used in the earlier period and some iron later when it became available. Blast was originally supplied by bellows manually operated. Such smelting was carried on to a greater or lesser extent until the latter part of the last century, and so extensive was it that many hundred thousand tons of leady slag remained to be treated in modern furnaces. In 1908 a smelter was placed in operation at Chihuahua by the American Smelting & Refining Co. At that time the ore was practically all oxidized and by a little selection, self-fluxing mixtures could be made, but with an average lead content usually under 10 per cent and sometimes as low as 7 per cent. The bullion produced would carry from 150 to 300 oz. silver per ton. The slag made approximated 30 per cent SiO2, 42 per cent FeO, 21 per cent CaO, and perhaps 3 per cent Zn. The ores varied from hard, coarse material which was passed through a crusher, to a considerable quantity of fines which had to be smelted as it came, as crushing the coarse was the only preparation for smelting.

Jan 1, 1933

By K A. Campbell, K A. Rodgers

The Plumduff sinter occurs at Whenuaroa, near Puhipuhi, approximately 30 km north of Whangarei. It is one of three residual sinters in the southern portion of a mid- to late-Pliocene geothermal system. The deposit consists of many large sinter breccia boulders, including rudrocks (coarse breccias), scattered around the flanks and summit of the small conical hill of Plumduff. Three types of sinter breccia occur: (i) rudrocks consisting of large, angular to sub-angular clasts of layered sinter up to 0.8 m across, as well as smaller clasts of sinter (20 - 100 mm dia), and fragments of stromatolitic structures; all clasts are supported in a matrix of microcrystalline, transparent to translucent to milky quartz; (ii) fragments of layered angular to irregularly mottled sinter of white to grey or bluish hue supported in a translucent to opaque silica matrix; (iii) smaller, matrix-supported breccias with clasts both partially surrounded and/or penetrated, by a clay-like weathering rind, and sinter conglomerates with rounded to oblate clasts. Three principal types of fabrics constitute the bulk of the sinter: (i) stromatolites, including columnar, palisade and filamentous networks, showing progressive silicification, in fenestral, tufted to clotted fabrics; (ii) peloids and pisoids; (iii) plant-rich facies in which various silicified plant species occur in a silica matrix. All fabrics have counterparts in hot spring deposits in the Taupo Volcanic Zone formed at temperatures from 75¦C to 35¦C. Also present is steam-condensate-produced alteration: kaolinite and alunite as well as boulders of quartz lattice texture. Cinnabar only occurs in sinter on the north and south central slopes of the hillside. No quartz veins or geyserite were recognised.

Jan 1, 2001

By R. E. Dye

IF gold mining is to assume, or it might be better said to resume, a place of ' importance in the national economy of this country following the present war, then one must accept the thesis that gold will maintain the place it has for many generations held in the minds of men as a substantial and lasting emblem of material wealth-a metal in exchange for which men have always been ready to give up the possession of their worldly goods. The thought bas been advanced by some that gold is not necessary as a basis for exchange, that it has no real value anyway and, therefore, the world would wake up some morning to find that no one wanted gold and that, over night, its possession bad in some way ceased to be desired. Holding an equally extreme view there are those who advance the idea that, following the war, gold will in some mysterious way enjoy a fantastic increase in value. Neither of these extreme views can be successfully supported. To presume that by legislation or by general agreement gold would be or could be, over night, dethroned to the position of common stone is wholly beyond the realm of any possibility. The thought that this could come to pass is advanced by, and is attractive to, only those peoples who do not have gold and do r:ot have the means of producing it. To believe that the fundamental value of gold will suddenly change is likewise fantastic. I refer to the fundamental value, not the dollar price, of gold, for it cannot be denied that, with the colossal war expenditures now being made and with the huge national debts which are being piled up, there is a possibility, indeed per-haps a likelihood, that the dollar price .of gold may be revised upward. For the purpose of this discussion, however, that possibility is irrelevant and need not be considered.

Jan 1, 1943

By Sarma S. Kanchibotla

In overburden cast blasting the explosive energy is used to move a significant percentage of overburden from the high wall to the spoil pile thus reducing the amount of material to be handled by machinery. However, the obvious trade-off between the extra explosive energy in the cast blast versus reduced dragline effort is complicated by an increased risk of damage to the underlying coal. This damage may not be obvious but inevitably leads to reduced coal recovery and may negate much of the benefit sought from cast blasting.

Jan 1, 1999

By James J. Dawd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the ninth of a series of reports giving results of studies by counties under part (1) of the investigation. (See Appendix.) This report covers Raleigh County, W. Va., which comprises parts of Bald Knob, Eccles, Beckley, Meadow Creek, Mullens, Flattop, and Big Bend quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, location of drill holes, bed and total coal thickness, and outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas. areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps, Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By Perry Harrison

THE increased use of sintering for the beneficiation of iron ores and the reclaiming of flue dust creates a lively interest in sintering costs and, economics. The character of material sintered and geographical location of plants so radically alter sintering costs and economics that it is well to understand at least the basic elements which control such changes. The following cost factors are believed to be roughly approximated for large-scale Dwight-Lloyd 'continuously operated sinter-machine installations located anywhere. PER CRUDE TON Labor, supplies and repairs 0.15 Power 6.5¢ X kw-hr. rate ? Plant overhead and administration 0.05 Depreciation per ton annual capacity 0.05 Fuel: 6 per cent coke breeze or equivalent minimum ? 1 per cent coke breeze additional for each 5 per cent free and combined water in ore or dust ? Ignition distillate at 0.6 gal. per ton ? PER SINTER TON Royalty on Ore 0.10 Royalty on Flue Dust 0.15 PER CRUDE TON "Winter expense"; i. z., the cost of the five months enforced idle . period for plants tied in to Great Lakes transportation season 0.03 Using the foregoing data, it is possible to roughly approximate the cost of efficient sintering at any location for. any ore, viz:

Jan 1, 1932

By Lon D. Santis

The Code of Federal Regulations Title 30, Parts 56, 57, 75, and 77 require that detonators and explosives be separated by four inches of hardwood or equivalents when transported together in mines. This standard was developed to protect the explosives from initiation by the more sensitive detonators. The research reported here is an attempt to quantify the fire protection offered by four inches of red oak and other materials. Boxes with a volume of 6.75 cubic feet were made from four-inch thick rough green oak (RGO), two-inch thick RGO plied, two-inch thick #1 common (dried) red oak plied, and a metal/plywood composite. These and boxes meeting the Institute of Makers of Explosives' (IME) Safety Library Publication No. 22 were tested in bonfires. The boxes were instrumented with thermocouples, filled with detonators, and placed over a kerosene fire imparting about 16 kilowatts per square meter heat flux for up to 3 hours. Tests showed that the wood boxes protected the detonators for over an hour with variations between the different trials. In the IME 22 container tests, detonators began exploding in as little as 17 minutes in one test and not for 2-/12 hours in another test. Detonators in the metal/plywood boxes began to explode in about 15 minutes but with minor alterations, were able to contain the detonators. The test results show that the exterior of an IME 22 container significantly affects its thermal properties. Defects in the form of cracks and the manner in which the container is closed have a significant effect on the performance of a detonator container in a fire.

By S. K. Wu, Ray Y. Lin, Sunil Annaji

Infrared joining of TiAI using aluminum foils as the filler material was investigated at temperatures between 1050 °C and 1350 °C in a flowing argon environment for times varying between 15 and 60 seconds. Using aluminum foils, the attempt was to form the Al3Ti phase in the joint as a result of reaction between Al and TiAI at temperatures above the melting point of Al. It has been found based on X-ray diffraction and TEM analysis that, Al3Ti, indeed is the product of infrared joining of TiAI using Al as the joining alloy. Al3 Ti was detected even in the joint processed at 1050 °C for only 15 seconds. Since the aluminum foil used in this study contains 27 at% Si, the t 2 phase in the Ti-Al-Si ternary system is believed to have also formed at the joint/base TiAI interface. Cross sectional studies on the joined specimens have shown different degrees of reaction depending on the temperature and time of joining. Micro hardness evaluations across the joint show that the hardness near the center of the joint is typically smaller than that near the joint edge next to the base material. However, as the joining temperature and time increase, the increment of the hardness at the center of the joint is faster than that around the periphery of the joint.

Jan 1, 1996

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By J. Keith Seidler, David R. Lentz, Douglas C. Hall, Nicholas Susak

Abstract - The Ta-Nb-Zr-REE-rich McKeel Lake alkali granite pegmatite-aplite dike swarm is hosted within the late Silurian multiphase alkali granite intrusion (Welsford) near Browns Flats in southwestern New Brunswick. A steep easterly dipping series of pegmatite-aplite dikes trending 170º can be traced 150 m along strike; they are up to 40 cm wide, closely spaced (10-20 cm apart), and interconnected by narrow branching dikelets that generally trend perpendicular to the overall strike direction. The Welsford intrusion has mantle A-type affinities characterized by enrichment of Zr, Ta, Nb, Th, and rare earth elements (REE). Two separate sets of dikes have been identified: (1) an unmineralized fine-grained porphyry, which occurs at depth and seems to be the youngest intrusive phase; and (2) a mineralized pegmatite-aplite dike swarm (419 ± 20 Ma) that crops out at surface. The mineralized pegmatite-aplite dikes likely represent a late magmatic, highly fractionated phase of the Welsford intrusion. XRF and INAA data indicate that the Welsford intrusions and related pegmatite-aplite dikes show elevated levels of Ta (74-220 ppm), Nb (750-3,040 ppm), Zr (1,450-36,000 ppm), Y (540-3,070 ppm), Th (170-870 ppm), U (60-250 ppm), Ce (430-1,950 ppm) and Yb (110-290 ppm). Electron microprobe analysis of two samples identified Ta-Nb- and REE-rich phases: euxenite, fergusonite, aeschynite, (Y)-aeschynite, and a REE carbonate.

Jan 1, 2005

By Paul M. Jr. Musgrove, Donald C. Moore

Conventional Smelting Practice Conventional copper smelting practice varies from smelter to smel¬ter, but generally consists of some or all of the following unit processes: roasting, smelting, converting, and fire refining. Roasting. Copper sulfide concentrates can be smelted directly or after an initial roasting step. Roasting is used in some smelters because roasting prior to smelting increases smelting capacity, less energy is required to melt hot roaster calcines than wet sulfide concen¬trates, roaster off gases are high in Sot concentration, 5-15% SO2, and some volatile impurities are removed from the concentrate prior to smelting. However, many smelters do not use roasters, because the problems associated with handling hot dry calcines outweigh the advantages mentioned. Concentrate roasting is performed in multiple hearth or fluid bed roasters. If the moisture is low, roasting can be performed autogenously, usually at 500-600°C. High roasting temperatures are avoided because excess oxidation of the iron compounds may lead to magnetite formation. Magnetite is detrimental to reverb operation because mag¬netite can combine with refractory minerals to form a highly viscous slag. This slag prohibits efficient matte-slag separation and leads to excessive copper losses. Also, magnetite can settle through the matte layer, deposit on the furnace bottom, and consequently reduce furnace capacity. Roasting is carried out only on sulfide concentrates prior to smelt¬ing in reverb or electric furnaces. For smelting processes, such as the flash and continuous that rely on the exothermic heat of oxidation of the sulfur minerals, roasting is not practiced. Reverberatory Smelting. The predominate copper smelting fur¬nace for the past 50 years has been the reverb. These furnaces are typically 100-120 ft long, 30-35 ft wide, and 12-15 ft high. A typical furnace layout is shown in Fig. 2. Refractory brick linings cover all internal surfaces of the furnace. Originally the flame was directed to reverberate or reflect off the furnace ceiling and melt the feed material. Current practice is to direct the flame down the furnace length to melt the concentrate. A method of charging the concentrates or calcines, generally along the side walls to minimize refractory erosion, is incorporated in the furnace design. The copper concentrates, calcines, and fluxes charged into the reverb undergo a series of complicated reactions as the temperature of the mixture increases. The reaction of the iron and copper sulfides with the oxygen in the furnace produces a molten Cu25-FeS mixture called matte. Copper smelting metallurgy is based on the fact that sulfur has a greater affinity for copper than for iron and most other common metals. Therefore, in a system containing copper, the copper will preferentially remain as a sulfide compound until all of the other metals have been oxidized. The oxidized metals combine with silica to form a silicate slag that floats on the matte and is removed from the system. Reverberatory furnace smelting chemistry can be approximated by the following chemical equations: FeS2 + O2 - FeS+ SO2 (1) The formation of FeS ensures that any copper present other than as sulfides will be reduced by the relationship: CuO2 + 2FeS + O2 - CuS + 2FeO+SO2 (2) or 2Cu +FeS - Cu2S + Fe (3) As the molten charge travels down the furnace, continued oxida¬tion of the iron minerals and sulfurization of the copper minerals occurs. When all of the copper has been converted to sulfides, the iron sulfides can then be further oxidized as: FeS + (3)2 O2 FeO + SiO2 (4) The FeO reacts with the silica added as flux in the furnace charge. A simplified equation is: FeO + SiO2 -FeO SiO2 (5) The iron silicate slag formed is skimmed from the surface at the end opposite the burners. The copper content of reverb slag is usually less than 0.6% Cu and is discarded. Matte is removed along the side wall and is taken to the converter for oxidation of the remaining sulfur and iron. The main objectives in reverberatory smelting are to produce a molten Cu2S-FeS matte containing 30-60% Cu and a throwaway slag. Production of matte permits complete conversion of all copper minerals into copper sulfides, which can migrate because of specific gravity differences, through the lighter slag layer. Also, the molten matte droplets collect the noble metals, gold and silver, as the matte settles in the furnace. The large settling area of the furnace provides enough separation time to produce a low grade slag, which can be discarded without further processing. High heat losses are associated with reverberatory smelting be¬cause of the large volume of gases sweeping through the furnace. Therefore, an outside source of heat is required to keep the smelting reaction going. Natural gas, fuel oil, or pulverized coal are used as this heat source.

Jan 1, 1985

The Project ? $1.4 billion project ? 59,000 tonnes of nickel and cobalt ? Large resource base ? First production end of 2004 The Place ? Half the size of Vancouver Island ? Population 210,000 ? 43% Melanesian, 37% European, 12% other South Pacific groups, 8% other nationalities ? Tourism principal industry ? 1/3 of world?s nickel resources The Politics ? French Overseas Territory ?1998 Noumea Accord: increased local control over domestic policy ? Referendum on independence in 2014 ? Seeking more economic autonomy, less dependence on French support

May 1, 2002

By R. K. McGeary, B. Lustman

Orientation relationships and rates of annealing of 97 pct cold rolled zirconium have been studied by X-ray techniques, metallography, and by hardness measurements. The process of annealing occurring by the formation of domains, and their subsequent growth without recrystallization, is demonstrated. NUMEROUS investigators1-' have revealed sub-grain formation after annealing cold worked metal single crystals and have generally described the results in terms of a dislocation mechanism of polygonization.5,6 in heavily cold rolled polycrystal-line aluminum the first stages of heating cause an apparently spontaneous subdivision of regions of the deformed matrix into a great number of slightly disoriented domains followed or accompanied by rapid growth of certain domains to form a recrystallization texture.7,8 In the present investigation the isothermal rate of annealing of cold worked polycrystalline zirconium has been studied by X-ray techniques, metallography, and by hardness measurement. It will be shown that, rather than by the usual nucleation and growth mechanism,"12 the process of annealing can best be explained by the formation of domains early in the annealing treatment and the subsequent growth of these domains without recrystallization. Experimental Procedure All the experimental work was performed on an arc-melted ingot of high purity zirconium crystal bar made by Westinghouse in a production scale deBoer unit. The weight percentage of impurities in the zirconium were as follows: C, 0.04; Fe, 0.05; Hf, 0.014; W, 0.01; Ti, Ni, and Al, 0.003; Si and N, 0.002; Cr and Cu, 0.001. Metallographically the zirconium showed only a single phase. The 4 in. diarn ingot was forged at 760°C to a 1 1/2x3 in. plate and was then rolled at 760°C to 0.150 in. thickness and annealed at this temperature for 20 min to produce an equiaxed grain structure of about 0.1 mm average grain diameter. The hot rolled plate was roller-leveled, surface ground to 0.135 in., cold rolled 83 pct reduction in thickness on a two-high mill, and then to a total reduction of 97 pct on a Sendzimir mill. The 0.004 in. strip material so produced received no subsequent mechanical treatment. Specimens % in. square were sheared from the rolled strip and isothermally annealed at 104 mm Hg in an all glass vacuum system equipped with a Vycor furnace tube. The temperature data presented are the average temperatures during the runs and did not vary more than about k3"C. X-ray Diffraction Methods: When zirconium is drastically cold rolled, a high degree of preferred orientation results in which prism poles, {1010}, are perpendicular to the rolling direction. After fully annealing this material an entirely new texture develops which corresponds to a 20" or 40" rotation of the deformation texture about hexagonal axes of

Jan 1, 1954

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By W. Grell

"In this paper, two methods of standardizing mill language are proposed; one is based on metric units and the other on English units. Tentative procedures for chemical and screen analysis based on published methods are proposed.Standard procedures for determining work index, and for leaching, flotation, and classification tests are outlined.Objects of Standardization:(1) to improve communication -(a) among gold metallurgists(b) with other branches of mineral dressing(c) with mineral dressing in other countries(d) with general scientific procedure(2) to improve mill control by -(a) standard methods of analysis (i)(ii)(iii)(b) standard methods of calcula tiort(c) standard accounting proceduresin the plantin the mill laboratoryin the assay office(3) to improve mill test work and investigationAreas of Standardization(1) Nomenclature or terminology(2) Measuring techniques(3) Test procedures(4) Accounting procedures"

Jan 1, 1966

By T Ladinig

Raise caving is a novel cave mining method, which has been proposed for mass mining at increasing mining depths in LKAB operations. The method makes use of the raise mining technology and an active stress management approach. For the implementation the method is split into two phases, namely a de-stressing phase and a production phase. In the de-stressing phase, a slot-pillar system is established. The purpose of slots is to provide stress shadows and the purpose of the large pillars is to control stress and seismicity. The production phase follows after the de-stressing phase. Required infrastructure in the production phase is developed delayed in stress shadows and bulk extraction takes place in de-stressed zones. Eventually the pillars crush and they are extracted in the production phase. A comprehensive research and development program has been launched to develop the raise caving method towards implementation. As part of this program a full-scale test site of raise caving will be conducted as well as raise caving operations are planned for depth extensions in LKAB mines. This paper discusses the design of raise caving operations in practice at the LKAB mines. In particular, the purpose of the paper is to focus on requirements for the development and design of a raise caving operation. The development of raise caving is discussed from a systems engineering perspective as well as from a management perspective. The functional requirements in the destressing and production phase are outlined and discussed in the paper. The discussion is on basis of the main elements of the raise caving system, such as slots, stopes, pillars and infrastructure. Critical rock engineering design requirements in the de-stressing and production phase are highlighted and dependencies between individual main elements are identified. The analyses show that pillars are especially important for the success of the mining method. Overall, the analyses show that raise caving is a complex system and that its development demands a multidisciplinary approach.

Mar 29, 2023

By V. G. Papangelakis, G. A. Moldoveanu

The use of anhydrite (AH) seed, control of acidity levels and ageing were assessed as means to promote the conversion of freshly produced metastable gypsum generated in-situ to the less soluble anhydrite phase and force deposition of calcium sulphate on seed as opposed to on equipment as scale, while achieving lower terminal aqueous calcium concentration as well. It was found that moderate sulphuric acid levels (0.25M) and ageing in the presence of AH seed accelerated the gypsum-AH conversion, achieving 100% transformation of the metastable gypsum generated in situ to the more stable, less soluble AH in 6-7 days, while lower/nil acidity did not promote more than 30% AH conversion for 10 days, even in the presence of AH seed. These findings indicate that anhydrite seeding, ageing and incomplete neutralization are beneficial for scale control as well as achieving lower calcium levels, thus rendering the resulting solution more amenable for recycling.

Jan 1, 2015

By A. M. Esteves

This paper offers an overview of local content policies and practice in the mining sector. Specifically, the paper aims to answer the question of how national and regional governments, industry and civil society can work together to seek an optimal outcome while pursuing their diverse objectives. The paper begins by defining local content and its scope at the subnational level. Specific recommendations for the design of local content policies to mitigate social, economic and governance risks are developed. The document then offers some recommendations regarding the role of partners in design, implementation, monitoring, and enforcement of local content policies.

Aug 1, 2013

In exploiting the ultra-deep, narrow reef ore bodies of the Witwatersrand, the ventilation and cooling systems within the stopes play a critical role because of high concentrations of active workers. This paper examines the heat, ventilation and cooling effects of a number of different stoping layouts for narrow reef mining in ultra-deep operations in very hot rock. The stope ventilation and cooling needs are driven primarily by the difference between the air temperature and that of the rock front being excavated. These needs depend on the face utilization, geometry, face advance (rate and direction), layout, backfill, use of water and machinery1,2,3. Detailed studies of different stoping configurations have been undertaken for mining operations extending to depths of 5000m below surface, where virgin rock temperatures approach 70°C. Extensive work has been completed with regard to evaluating ventilation and cooling requirements to maintain air reject temperatures of 28°C wet-bulb and better. This knowledge is being used to determine overall cooling requirements, reduce operational costs and maximize the efficiency of cooling systems. These issues are important when considering both the local and regional air conditioning systems and the most effective application of in-stope chilled water.

Jan 1, 2001