Search Documents

By Nabil F. Ismael

"Load tests were carried out to examine the ultimate bearing capacity of short, large diameter bored piles in connection with the construction of a multistory building on the Arabian Gulf in Kuwait. Testing included 0.45 m, 1.0 m, and 1.2 m piles installed through loose sand into a bearing stratum consisting of very dense cemented sands. All tests were carried out to failure. The base resistance and shaft friction were calculated using the Meyerhof method for a layered soil profile. The method employs the standard penetration test N-values. The results indicate that the piles are end bearing piles with a great portion of the pile capacity due to base resistance. The mobilized skin friction is small. The calculated pile capacities were very close to the measured values with the maximum difference not exceeding 10%.INTRODUCTIONShort, large diameter bored piles are used with increasing frequency for heavy structures in Kuwait, and the Gulf region where ground conditions indicate loose deposits of calcareous sands. The piles range in length from 8 m to 15 m with their base located in the dense-to-very dense, cemented sand bearing deposit. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on large diameter bored piles installed through loose calcareous sands into dense-to-very dense cemented or partially cemented sands are very limited at present. The results of three load tests carried out recently on bored piles at one site in Kuwait have become available. In these tests the failure load was either reached or can be extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers.This paper presents the soil conditions, pile installation details, and the pile load test data at the test site located in Shuwaikh, Kuwait. The site is facing the Arabian Gulf. Test results were directly analyzed and the point resistance, and skin friction were calculated. The ultimate capacities of the piles were calculated and compared with the measured values. The influence of the pile diameter on the settlement at ultimate and at working loads is examined"

Jan 1, 2017

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the sixth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Fayette County, Pa., which comprises the Uniontown and parts of the Brownsville, Connellsville, Donegal, Waynesburg, Masontown, and Confluence, Pa., Morgantown and Bruceton, W. Va., and Accident, Md., quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals ar.9 included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information.

Jan 1, 1951

By M Zaluski, D Bless

An innovative, biological treatment process has been designed by MSE Technology Applications, Inc to treat and control acid mine drainage (AMD). A field-scale demonstration is being conducted under the Mine Waste Technology Program using water flowing from a historic mine in Montana. A successful demonstration of an in situ process will allow it to be employed at numerous other abandoned or remote mines, which discharge AMD, an acidic, metal-contaminated water. Conventional treatment methods are costly and are often impossible to use at remote locations. MSEÆs technology uses a biological system to clean up AMD. The In situ Passive Biological Treatment Process utilises nonpathogenic bacteria, which are able to neutralise acidic mine water and remove contained toxic metals. These bacteria live within a series of pile-type reactors inside the mine. The bacteria are fed inexpensive waste products. The resulting discharge is clean water flowing from the mine. This presentation will show that this technology offers a natural cleanup method for the nationÆs numerous abandoned mines. Work on this project was conducted under Interagency Agreement No DW899388-70-01-1 between the US Environmental Protection Agency and the US Department of Energy (DOE), and was performed at the Western Environmental Technology Office through the DOE National Environmental Technology Laboratory (DOE Contract No. DE-AC22-96EW96405).

Jan 1, 2003

By Allen F. Agnew

Geologic studies for the Federal and State governments in the Wisconsin-Illinois-Iowa zinc-lead district were begun in 1835, and subse¬quent surveys were made in the three states at in¬tervals until 1916, see Table I. The current study of the district, Fig. 1, by the U. S. Geological Survey was begun in 1942 in the hope that a systematic investigation would help in¬crease production of zinc and lead, then in ex¬tremely short supply. Major emphasis of the USGS program was on detailed mapping of the geologic structure and ore deposits. Preliminary maps and reports covering localities of intensive mining ac¬tivity have been published during the course of this study, Fig. 2. By 1950 the objectives of the study by the USGS were revised; 7Y2-min quadrangles of relatively unprospected localities as well as inten¬sively mined localities are now being mapped in Wisconsin. Since 1945 the investigation in Wiscon¬sin has been made in cooperation with the Wiscon¬sin Geological and Natural History Survey, and since 1951 the geologic mapping of areas of particu¬lar interest in Iowa has been performed in coopera¬tion with the Iowa Geological Survey. At intervals since 1943 the Illinois State Geological Survey has mapped the geologic structure and ore deposits of localities in the Illinois part of the mining district, see Fig. 2.

Aug 1, 1955

By Brad Bjornson, Geoff Stevens, Mike Ashar, Cliff Britch

"LocationThe facilities are located 30 km north of Fort McMurray, Alberta (or 470 km northeast of Edmonton, Alberta).Brief Description of OperationThe operation includes the mining of oil sands, extraction of bitumen from the oil sands, and upgrading of the hydrocarbon fraction prior to shipment via pipelines to refineries.HistorySuncor was initially called Great Canadian Oil Sands. It was started by Sun Oil of Philadelphia. Construction began in 1965, with the first production coming on September 1967.Details of Present Milling Practice (Plant 3)Plant 3 recovers bitumen from the oil sand using the Clark hot water process. The basic steps in the process are conditioning, primary recovery, secondary recovery and tailings oil recovery.Oil Sand Feed SystemThe oil sand feed from the mine is transferred to the feed bin in extraction by two conveyor systems. Oil sand analyzers on each conveyor system measure the amount of bitumen and fines in the ore. Cones at the bottom of the feed bin distribute the oil sand to five process lines. Feed flow from each cone is regulated by an apron feeder which transfers the oil sand to conveyors that discharge into the conditioning drums. Weightometers on each of these five conveyors measure the rate at which the oil sand is delivered into the drums. The oil sand feed rate to each drum can be adjusted by varying the speed of the apron feeders."

Jan 1, 2000

By A. Brown

"The mining industry is no exception to the general rule that continuing research is essential to good management; in fact, because of the imperfect state of knowledge in regard to many important factors associated with a mineral extraction, mining research assumes a position of unusual importance. On the basis of a recent visit to mining research centres in a number of European countries, the author describes their organization and their role in the mining industries of these countries. Some observations are made on Canadian mining research efforts, with a view to indicating a more systematic basis of procedure."

Jan 1, 1960

By M Darby, B Burdett, F Lovell

The results of the process control improvement project aimed at improving the quality of Australian Bulk MineralsÆ (ABM) iron ore pellets produced by four vertical shaft furnaces are very positive. These results are achieved through process stabilisation and optimisation, improvement in process monitoring and taking early corrective actions when operating variables were outside the target ranges. A number of benefits are obtained from this project. These benefits include: More consistent and improved pellet quality. The average cold compression strength (CCS) value of pellets produced during the eight-month trial is 260 kg/pellet, which is 16 kg/pellet higher than that produced during the 12 months prior to the trial (244 kg/pellet). Reduction in the heat input by eight per cent, from 727 MJ/tonne to 668 MJ/tonne. Reduction in bentonite rate by six per cent, from 7.1 kg/tonne to 6.7 kg/tonne. Increase in the furnace throughput rate by four per cent and additional production of 10 000 tonnes per annum through process stabilisation. Better understanding of the process behaviour. This knowledge is valuable not only for setting the target operating conditions but also for developing the ABM expert system to control the process.

Jan 1, 2005

A decision by joint-venture partners Anglo American, Gencor, and the Industrial Development Corporation to proceed with the expansion of the Columbus Stainless Steel plant in Middelburg will contribute significantly towards the economic growth that South Africa needs so desperately. The expanded facility, expected to come on-line in 1995, will be the largest single-plant producer of stainless steel in the world, and the company will rank sixth overall in world production.

Jan 1, 1993

By N. C. Joughin

A simplified economic model is derived for the financial return from a new gold mining project. The model is used to analyze the effects of changes in the mining rate, capital costs, working costs, value of the reef and the stoping width. The most effective avenues for improving the return from a new project are indicated. It is shown that those technological innovations which would improve the return significantly, and therefore make it possible to open more mines, are the use of smaller mines, means for improving the mining rate to capital costs ratio for smaller mines, planning and control of mines by computer simulation, an improved mine valuation procedure and means for mining at a decreased stope tramming width.

Jan 1, 2014

By R. Brantley Sudderth

There are three broad categories in which most solvent extraction technology can be distributed?: 1) reagents, 2) equipment, and 3) systems. Reagents which are now used in commercial solvent extraction plants are of many chemical types, and each possesses certain properties which make it more economically desirable than another alternative. The equipment which is' used in solvent extraction plants for contacting the organic and aqueous phases and separating the same is varied. Most common to the industry is the mixer-settler unit which in itself, can be of varied design; but many new innovations in contacting and separating equipment have been recently introduced or are :now being studied. Each specific solvent extraction application will often dictate the type of contacting and separating equipment used. Obviously, the trend is toward smaller less expensive equipment which reduces the often expensive organic inventories necessary for most solvent extraction plants. The current thrust of .investigations in ancillary equipment is usually aimed at recovering organic from solvent extraction sludges or from aqueous streams exiting the process.6 This type of equipment helps to reduce the total organic losses from solvent extraction plants and thus reduce the operating costs. The term "systems" in solvent extraction applies to the manner in which a solvent extraction process is carried out. This manner is usually dictated by the properties of the reagent which is used, and it involves a tailoring of the equipment or the process flowsheet. Some of the things which can be tailored are: 1) The aqueous media -whether acidic or basic and what type of acid or base 2) Counter-current or single stage (co-current) contacting 3) EMF or pH control 4) Organic "crowding" alternative 5) Heating or cooling process streams Regardless of the type or extent of tailoring, efforts to do this are usually a result of the low cost of solvent extraction as a unit process.

Jan 1, 1977

By Kihong Park, Matthews C. Habjan, Arthur L. Miller

New Mining Safety and Health Administration (MSHA) regulations limit the mass concentration of airborne diesel particulate matter (DPM) or, more specifically, the concentration of elemental carbon (EC), in underground mines. The mine operators are responding by introducing a variety of controls to reduce DPM in the mines, potentially including the evaluation of new maintenance procedures to reduce underground mine vehicle emissions. There is currently a lack of an inexpensive and dependable method to directly measure the DPM concentration emitted from the vehicle tailpipe. To that end, this work demonstrated a simple field portable method for estimating the mass concentration of elemental carbon exiting the tailpipe of a diesel engine using a direct reading photometer. Simultaneous measurements of tailpipe exhaust were made with a Thermo Electron Personal DataRAM 1200 photometer (particulate mass concentration based on light scattering) and by analyzing PM2.5 and PM1.0 samples collected on quartz fiber filters using the National Institute of Occupational Safety and Health (NIOSH) method 5040 (mass concentration of EC via thermal-optical method). Results indicate surprisingly good correlation (R2 ) 0.97) of the two methods when the data are adjusted for relative humidity (RH) and corrected using an empirically generated calibration factor. Although preliminary, it may be possible to implement this method in maintenance shops to monitor emission trends and to compare emissions of various vehicles in a fleet. Such data will be useful for fleet planning to meet new air quality standards.

By Gupta R. C

Direct reduction of iron ore by solid reducing agents have been studied extensively and summarised by several authors (Otsuka and Kunii, 1969; Abraham and Ghosh, 1979; Frauhan, 1977; Rao, 1971; Kawasaki, Sanscainte and Walsh, 1962; Ghosh, 1970; Rao, 1979). While studying the reduction behaviour, it is generally agreed that the reduction occurs via gaseous intermediate, generated by carbon gasification reaction which involves mass transfer, heat transfer nucleation and growth, etc through a) reduction reaction occurring at solid reductant, and b) reduction reaction occurring at solid iron oxides, thus making the overall reduction process very complex in terms of clearly defining the reduction kinetics of the system. In addition to this, practical difficulties like correctness of reaction temperature, (Seaton, Foster and Velasco, 1983) difficulties in isothermal temperature studies of reduction, difficulties in monitoring the reduction process while using gaseous reductants and separation of reduction by volatile matter from overall reduction process make the reduction kinetics more complex (Misra).

Jan 1, 1999

By Rodrigo Abreu, Nilson Luiz Biccas, André Luiz Bonelar dos Santos, Odilon José da Silva

A Coqueria no contexto siderúrgico é a área responsável pela produção de coque metalúrgico para os Altos-Fornos. O coque geralmente é obtido em fornos verticais, que tem a finalidade de aquecer a mistura dos carvões minerais até a temperatura de pirolise, através da queima controlada de um combustível. O objetivo deste trabalho é apresentar as alterações realizadas no Controle de Combustão das Baterias de Coque da ArcelorMittal Tubarão para garantir a estabilidade operacional e o maior controle do tempo líquido de coqueificação. O aprimoramento do modelo matemático ajustado as condições atuais do processo, trouxe benefícios tais como a obtenção de uma melhor distribuição de calor ao longo das paredes de aquecimento e consequentemente a redução das resistências aos desenfornamentos, consumo de calor e emissões de poluentes, preservando a estabilidade operacional das baterias de coque e contribuindo para o prolongamento da vida útil.

Oct 1, 2019

The effects of additives, sodium hydroxide, sodium carbonate, sodium oleate, oleic acid and polyacrylic acid, on stirred media milling of limestone have been investigated. The results are evaluated in terms of specific surface area, specific energy and energy efficiency as a function of additive dosage, polymer molecular weight, solids concentration and relevant operating variables. Use of additives generally results in changes in specific surface area and energy efficiency, while under certain conditions a more than 100% increase in these parameters can occur. Relevant interfacial properties have been measured and milling mechanisms involved are explored particularly in terms of the effect of additives on the flow patterns at higher solids concentration.

Jan 1, 1996

"Discrete Fracture Network (DFN) modelling has increasingly being used in many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to provide updated guidelines that address the collection of discontinuity data in the specific context of DFN models. In general terms, the generation of a DFN model requires collecting information on i) fracture orientation, ii) fracture intensity, iii) fracture length and iv) fracture terminations. The International Society of Rock Mechanics (ISRM) suggested methods for the quantitative description of discontinuities in rock masses directly include most of these parameters. However, there are important differences engineers should be aware. To what extent discontinuities can be sampled and which limitations are inherently introduced in the analysis by the sampling methods being adopted represent important aspects that should drive the collection of discontinuity data for DFN analysis; this will require the introduction of a more appropriate set of guidelines bridging the gap between the current, very practical, ISRM methods and the data requirements imposed by the use of new DFN technologies.INTRODUCTIONThe last decade has seen a major increase in use of the Discrete Fracture Network (DFN) approach, both as a stand-alone tool or integrated within more complex geomechanical simulations (Rogers et al., 2014 and Elmo et al., 2014). In particular, the DFN approach offers the opportunity to maximise the use of fracture data collected from mapping of rock exposures and to construct synthetic rock mass (SRM) models. However, the potential of DFN based modelling is limited if there is insufficient care in collecting the necessary structural data at the required engineering scale. DFN models are also subject to the process of data calibration and validation (Hadjigeorgiou, 2012). With DFN modelling becoming an almost integral part of many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to review the process of collecting fracture data in the specific context of DFN modelling.The value of the DFN model depends directly on the quality and quantity of available field data. For example, fracture length (persistence) is an important parameter in DFN modelling; however, this parameter is either seldom available at the pre-feasibility stage due to a lack of exposures (man-made or natural), or engineers have access to limited length data collected along exploratory drifts. Characterisation of rock exposures should also take into account limits of window/scanline mapping techniques with respect to both trace length bias and the effect of cut-off assumptions inherent in the mapping methodology."

Jan 1, 2015

By Walter V. Knopp, Laurence Delisle

INTRODUCTION THE aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixture of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion corresponding to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low cost material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, i.e., finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemental powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: 1. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. GENERAL PROCEDURE The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1948

By Paul M. Tyler

The alkali metals , sodium and potassium , and more particularly sodium , occur abundantly in chemical combination with other elements . The elements themselves are available in metallic form but are so active chemically that they oxidize rapidly in contact merely with the air . Potassium will even catch fire spontaneously in air , and both the metals will decompose water with explosive violence . Inasmuch as they are almost as soft as wax they are not suitable for the structural or other mechanical uses characteristic of ordinary metals , and consequently the uses of these elements even in the metallic condition are based upon chemical rather than physical qualities . Sodium metal is used largely as a commercial reducing agent , but potassium metal is rarely found outside of chemical laboratories . Numerous salts and other compounds of these elements enter largely into world trade and are commercially very important , but none of these compounds except sodium peroxide and sodium cyanide are made economically from the metals . Sodium is generally considered as rather an uncommon metal , but in point of annual tonnage produced it is far more important than mercury , magnesium , molybdenum , bismuth, cadmium, cobalt , gold , silver , or the various rarer metals .

Apr 1, 1932

By Julie Dénommé

Today few in business would argue with the idea that we are living in a world that is Volatile, Uncertain, Complex, and Ambiguous. Coined VUCA by the US Army War College, these four words define the ?turbulence? and ?continuous white water? that the business literature has been documenting for the last decade. This VUCA world became even more relevant to business in 2007 when the Institute for the Future fellow Bob Johansen published the idea of transforming VUCA into Vision, Understanding, Clarity, and Agility. We call this VUCA Prime (VUCA'), and place an infinity loop (8) between them to show their dynamic interaction. This paper presents an exploration of the impact of VUCA 8 VUCA' on business and the conditions under which these dynamic forces help to successfully navigate change.

Oct 1, 2010

By E. Allain

Extraction of basic metals from sulfides by conventional pyrometallurgical processing leads to the emission of SO2. To avoid this inconvenient, low temperature selective chlorination of sulfide concentrates could be an alternative. However, such process generates hazardous chlorides SxCly. A part of sulfur chlorides such as SCI2 can be recycled as a chlorinating agent of metal sulfides. Hydrolysis of sulfur chlorides, using a solution containing Na2S.9H2O, led to the recovery of more than 90 pct of elemental sulfur. Reduction of SxCly by hydrogen was investigated between 300 °C and 800 °C. About 70 and 90 pct of elemental sulfur were recovered from SC12 and S2C12, respectively. A flow sheet for the chlorination of metal sulfides and the treatment of sulfur chlorides was suggested.

Jan 1, 1998

By G. T. Brookman, P. B. Katz, D. K. Martin, J. A. Ripp

With the increasing emphasis on using American fossil fuel resources, more facilities are evaluating coal conversion. In addition, those facilities now using coal are considering better coal storage procedures to minimize negative environmental impacts. For example, rainfall and snowmelt on a coal pile produce a drainage stream high in acidity, suspended and dissolved solids, iron, sulfate, and trace metals. Usually, the characteristics of the runoff stream do not allow for direct discharge to streams and lakes. Detention in a holding pond and pH adjustment are traditional methods of treating coal pile runoff before discharge. Historically, this treatment methodology has been performed inefficiently without a good data base to assess how much runoff treatment is needed to meet effluent guidelines. A model was developed to simulate runoff volume and pollutant loadings under different rainfall conditions. This model will be used to size and design treatment works for coal pile drainage. The Ohio State University (OSU) version of the Stanford watershed model was selected as the base model. The OSU model simulates overland runoff in a rural area. It includes factors such as soil moisture, depression storage, infiltration, and flow to a ground water reservoir. TRC also used the OSU co-model for acid production in coal refuse piles as the basis for qualitative modeling work. A number of modifications were made to the OSU models to make them applicable to coal storage piles. The physical/chemical reactions included in the models are described in more detail in the project report. In addition, the models were altered so that a standard NOAA magnetic tape of historical meteorological data can be used as data input instead of requiring the user to create a data file. The resulting TRC coal pile drainage model is actually two models - a quantitative model, termed H2OTRC, and a qualitative model, TRCCOAL.

Jan 1, 1984