Search Documents

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By D. M. Metcalf

MOST PEOPLE think of peat as an inferior substitute for coal as a fuel, and will be surprised to learn that it is extensively mined in this country for use as fertilizer rather than as a fuel. Some years ago the Florida Humus Co. began producing it at Zellwood, Orange County, Fla., in a small way for local use. When, however, the company secured an Institute member, M. H. Cuise, to apply his wide experience in mining to the problems here it was found possible to decrease production costs 70 per cent and increase output tenfold. The obvious way in which to decrease costs was to replace shovel-and- horse methods with machinery, much of which, in order to keep down-invested capital, was improvised by remodeling second-hand equipment, changing the design where necessary to meet the special conditions involved.

Jan 1, 1932

By D. J. Parker

The ease of ignition and violence of explosion of Utah coal dusts, together with the large volumes of methane given off in some of the mines of the State, made it imperative to abandon obsolete equipment and obviously hazardous practices for up-to-date equipment and safer methods of mining if reasonable progress wore to be attained in fire and explosion prevention. Although much can still be done to improve safety conditions in Utah coal mines, considerable progress has been made in the past 10 years. The fundamentals of such progress include increased use of permissible electrical equipment in gassy mines, closed lights, rock-dusting, more liberal use of water at the face, butter ventilation, permissible explosives fired electrically both within and without the mine, partial inhibition of blasting while the shift is in the mine, 100-percent first-aid training, increased supervision and inspection, and mass safety meetings.

Jan 1, 1935

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, the National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By Woolsey Johnson

THE object of this paper is to, describe the several necessary characteristics of the zinc-retorting charge and to show how by certain improved methods; the large excess of coal, over that theoretically required, can be reduced, thereby effecting an increase in the smelting capacity of a retort plant as well as other economies. In the Southwestern zinc works a charge of roasted zinc ore with a side mixture of carbonates and silicates, analyzing on the average 50 per cent. Zn, is mixed with 55 or more per cent. of its weight of a mixture of coal and coke analyzing 60 to 70 per cent. fixed carbon. . The ore is of varying fineness and the coal and coke are usually crushed in a semi-moist condition through a 3/8 -in. screen. With ores of a slaggy nature, this coal proportion is increased, sometimes to as much as 100 per cent. of, the weight of the ore. With carbonate ores, or where anthracite screenings with higher carbon content are cheap enough, the percentage of reducing agent is cut to 45 per cent. or even somewhat lower. The average charge per retort for a monthly run of a plant on ore, as distinguished from retorts on blue-powder, ladle-skimmings and other between-products, runs from 60 to 66 lb., with a mean of 63 lb. for the Southwest with standard retorts of 8 ½ -in. inside diameter and 50 in. long inside, using roasted sulphide ores. Conditions will change these figures, but 40 lb. of ore per cubic foot of retort space is, I believe, an average in the better-operated plants. Since the rise in. the price of spelter, the tendency has been to overcharge. To remove the slag that is formed when retorts are overcharged, extra men are put on to "gum-chisel" the retorts to prevent "set" furnaces and "butchered, retorts." Taking the above conditions as premises, we find that from four to six times the amount of coal necessary for the reduction is used, as is evidenced by the fact that the residues analyze as high as 35 per cent, fixed carbon. There are good reasons why this excess of fixed carbon must be used and perhaps these can be best explained by a description of the metallurgical requisites of a zinc charge. We may enumerate these as follows: 1. High reducing power, especially at the end f the shift, to reduce any carbon dioxide to monoxide and bring about a good condensation

Jan 2, 1918

By Cínthia Toshimi Ogata

Processos de fundição de ligas de alumínio com altos teores de Mg são um desafio da indústria, uma vez que diferentes taxas de resfriamento ocorrem em geometrias diversas. Este trabalho tem como objetivo caracterizar a liga de alumínio AA5052 com variações em teores de Mg por meio de experimentos de solidificação direcional transitória, e compreender seus efeitos com relação a evolução de parâmetros térmicos, microestruturais, e propriedade mecânica. As leis experimentais de evolução do espaçamento dendrítico primário (?1) com relação a taxa de resfriamento resultam em: ?_1=640 ?T ?_L?^(-1/4) para a liga 5052 com 2,4%Mg e ?_1=300 ?T ?_L?^(-1/4) para a liga com 3,2%Mg. As leis de crescimento de espaçamento dendrítico secundário (?2) com relação a velocidade de solidificação resultaram em: ?_2=27 ?V_L?^(-1,1) para a liga 5052 com 2,4%Mg e ?_2=15 ?V_L?^(-1,1) para as ligas com 2,6%Mg e 3,2%Mg. Maiores teores de Mg na liga AA5052 proporcionaram uma expressiva redução no valor de ?2 para uma determinada VL. A evolução da dureza mostrou-se diretamente relacionada ao tamanho e a distribuição dos intermetálicos presentes, sendo ?2 o fator predominante neste controle.

Oct 30, 2017

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems include: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of environmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental difficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 9, 1980

By James J. Bryja

The production capabilities of today?s longwall systems have resulted in significant increases in retreat rates. This has in turn resulted in a heightened demand on panel development rates to assure that subsequent panels are completed in time to avoid a longwall production outage. As a means of reducing the pressure on the panel development activity a trend has developed towards the use of wider face lengths. The aim of using a wider face is to reduce the longwall retreat rate without sacrificing productivity and thereby reduce the pressure on increasing panel development rates. However, as the face width increases so too does the number of hydraulically powered roof supports that are required to control the longwall face roof. This increase in the number of units inherently translates into increases in the level of required maintenance relative to the multitude of mechanical and hydraulic components, and an increase in the time required for tear-down and installation time during the moves between panels. An obvious method of mitigating the maintenance and move-time impacts of wider faces is to employ the use of individual roof supports having a wider center-to-center spacing. This practice would serve to minimize the number of roof supports and maximize the time availability for longwall face production. With this target in mind a joint research project with DBT was initiated in 1998 to study the feasibility of using 2 m wide shields to replace the then standard 1.75 m wide shields. After four years of comprehensive work, the technical team from DBT and RAG American Coal completed the design and development of a prototype shield that would later become part of the world?s widest longwall face employing the use of shields having a spacing of +2 meters. The final spacing of the shields actually became 2.058m in order to match the standard pitch of the rack bar shearer haulage elements on the conveyor. In July 2002, the 2 m wide shields were successfully installed in LW-46 panel at RAG Cumberland mine in the U. S. The authors in this paper summarize the design considerations of and operational experiences with the world?s widest longwall face using +2 meter wide roof supports.

Jan 1, 2008

By Edmonds W, Jeffcoat R

The completion of the first two open hearth furnaces in the new No. 2 open hearth plant at Port Kembla will increase Australian production of steel by 350,000 tons of ingots per annum.The paper gives an outline of the essential features of open hearth design and auxiliary equipment required to operate the two modern open hearth furnaces at present being installed.INTRODUCTIONThe increasing demand for steel required by Australian secondary industries led to the decision to construct and operate No. 2 open hearth plant at Port Kembla. Two basic open hearth furnaces of the most modern design are under construction and it is anticipated that these units will be commissi.oned in September 1956. Australian steel capacity will thereby be increased by approximately 350,000 tons of ingots per annum.PLANT LAY-OUT AND CONSTRUCTIONIn the design and lay-out of this plant the emphasis has been on efficient material handling with simplicity of design and operation. Overseas methods were studied and these studies, together with experience gained at Newcastle and Port Kembla open hearth shops, enabled this plant to be built to a standard which compares favourably with any other in the industry.Initially two furnaces, each of 2,75 tons capacity, have been built, but provision has been made in. the design and lay-out to enable expansion to six furnaces.The location of the new plant in relation to the existing units will be noted in Fig. 5. It is one of the first units to be built in an area which will dovetail into a pattern for...

Jan 1, 1957

By Raja V. Rarnani, Robert L. Frantz

More than 100 scientists from diverse professional backgrounds have contributed their expertise to the Dust Center as investigators. Approximately 50 researchers served as principal investigators, with responsibility for directing the work on Center projects, from experimental design and implementation in mines and in laboratories to coordination of efforts within the research infrastructure of the Center. The professional biographies which follow demonstrate the breadth and depth of research capabilities brought to the Center by its principal investigators.

Jan 1, 1995

By T. M. Gurr

Large quantities of phosphate rock are mined and processed in Central Florida (Figure 1). The phosphate rock from the mines is further processed in "chemical plants" to produce phosphoric acid (Figure 2). A by-product of the processing' of the phosphate rock to produce fertilizer chemicals is an impure form of gypsum referred to as phosphogypsum. For each ton of phosphate rock processed, approximately 1.5 tons of phosphogypsum is produced (Figure 3). The typical method to dispose of this by-product gypsum is to stack it in large piles, locally referred to as gypsum stacks or gypsum fields (Figure 4). These gypsum stacks have been the focus of many studies in recent years in an attempt to identify the potential for ground water and/or air pollution associated with the stacks. This paper attempts to discuss some of the ground water impacts and current attempts to minimize these impacts.

Jan 1, 1990

By Edward J. Zeigler, John T. Miller

INTRODUCTION Construction of Phase I, Section A, of the Baltimore Region Rapid Transit System required that six underground stations be built using a cut and cover excavation technique. For five of these stations, soldier piles, used as support of excavation, were installed with tip elevations well below the bottom of the excavation. However, in the case of the sixth subway station, the Mondawmin Station, soldier piles were installed only through soil and decomposed rock, with the tips of the piles being stopped well above the bottom of the excavation in partially decomposed rock. Below the tips of the soldier piles, and below a cut slope where piles were not installed, the sides of the excavation consisted of partially weathered and fresh rock and were supported by a combination of rock bolts, wire mesh and shotcrete. An extensive installation of geotechnical instrumentation permitted detailed monitoring of horizontal and vertical movements of the soldier piles and the walls of the excavation. Preliminary studies indicated that the excavation support system selected for the Mondawmin Station would have several advantages over a conventional system consisting of soldier piles extending to the bottom of the excavation, braced with prestressed struts. These advantages included lower cost of installation, a decreased time required for installation, and a more open excavation for the contractor during construction of the station. The Mondawmin Station is situated in the northwestern quadrant of Baltimore City, approximately 6.4 km (4 miles) from the center of the City. The station lies midway in a project 12.9 km (8 miles) long identified as Phase I, Section A, of the Baltimore Region Rapid Transit

Jan 1, 1981

By T. L. Joseph

The extent to which hot metal from the blast furnace affects open-hearth practice and the quality of steel produced has been discussed widely. Open-hearth operators have attributed difficulties experienced in making satisfactory steel to characteristics of the pig iron not disclosed by ordinary analysis. The commonest criticism of the iron has been that it is "physically cold" or "dirty." Often when the blast furnaces are working irregularly the quality of the iron is questioned. A cold hearth, slipping and hanging, the use in the past of unsintered flue dust, and the use of ores difficult to smelt have been associated with the production of iron of poor quality. The difficulty of the situation is that we have no proven yardstick for quality aside from ordinary analysis. Uniformity in analysis is recognized as being important, but the difficulty of changing the open-hearth practice when the iron analysis varies widely may not always be fully appreciated. Although the problem of correlating the characteristics of steel with those of pig iron is admittedly obscure, the effort of producers of quality steel to investigate all factors that may have a bearing on the final product is justified. This report contains data on the oxides in several hundred casts of basic iron produced in a furnace during the course of normal operation on Lake ores. Incidental to the study of the oxides in the iron, it was desirable to follow closely the temperature of the iron. The effect of temperature of the iron upon the silicon and sulphur present is discussed. A general relation between the basicity of the slag and the sulphur in the metal was developed. The amount and composition of oxides in the hot metal and in the steel bath during various intervals between melt-down and tap are discussed. Heats of rimmed steel, killed steel, and semikilled steel were investigated. The hot metal on individual heats was either all taken from a mixer or consisted partly of direct metal and partly of metal from the mixer. Samples of the iron for oxide determinations were

Jan 1, 1937

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The effects of ternary and quaternary additions of aluminum, oxygen, and carbon on the mechanical properties of high-purity titanium-molybdenum alloys were studied for several microstructural conditions. Heat treatments were designed to produce 1) ß-quenched, 2) equiaxed ß) transformed (acicular) and 4) stabilized -P microstructures. Tension, impact, and hardness tests were performed. Transformations from the ß phase were followed by hardness measurements and metallography. The ß-to-w transformation was slowed by aluminum additions; carbon and oxygen additions increased the transformation rate. In addition to solid-solution strengthening, these solutes may increase or decrease strength by altering the /3 transformation kinetics. Aluminum additions promote the formation of strain-induced martensite, and lower yield strengths at compositions near 12 pct molybdenum.. a-P alloys are more ductile with equiaxed than with transformed microstructures. High strength levels can be reached by aging in many cases. Strength levels of the aged specimens usually are lowered slightly by straining prior to aging. ALLOYS of molybdenum with titanium form an iso-morphous alloy system which has been the subject of several investigations. Additions of substitu-tional and interstitial -stabilizing elements provide means of improving mechanical strength and con- trolling the heat-treatment response of the binary alloys. The work reported here forms a part of a continued study of the effects of microstructure on the mechanical properties of high-purity titanium alloys. Previous papers have considered the various binary alloys (Ti-Mo, Ti-Al, Ti-C, and Ti-0) that form the bases for the ternary and quaternary alloys included here. The compositions were selected to correspond with the previous binary alloys. Further, the high purity of the alloying components was maintained, so that direct comparisons with earlier work can be made. The total research program included a large number of compositional, microstructural, and testing variables. The data reported here have been selected to provide a reasonably complete and representative summary of the results. The reader is referred to the original Air Force Report for a complete tabulation of the results. EXPERIMENTAL PROCEDURES All the alloys used in this work were prepared from high-purity electrolytic titanium produced by the U.S. Bureau of Mines. A typical furnished analysis showed the following impurities in wt pct, balance This analysis is equivalent to that of iodide-refined titanium. In addition, hardness, tensile, and impact tests made using unalloyed electrolytic titanium showed it to have properties equivalent to those obtained with iodide titanium and suitable for these studies of high-purity base alloys.

Jan 1, 1962

By G. M. Steed, A. O. Oyinloye

The deposit lies in amphibolite-facies biotite granite-gneisses of Proterozoic age, 4 km east of a major crustal break known as the Ifewara-Zungeru fault. Gold mineralisation is contained in a zone of quartz-carbonate (mainly calcite) veins and hydrothermally altered gneisses with associated small-scale intrusions along a steeply dipping second-order fault zone that roughly parallels the main fault. Gold is present mainly at grain boundaries between quartz and carbonate as discrete particles up to 100 micrometres in size, in general association with sparse, scattered pyrite, pyrrhotite and some base metal sulphides. Adjacent to the gold-bearing zone the granite-gneisses have been hydrothermally altered with minor volume increase, most notable enrichment being in K2O, S, Pb and Cu (and Au). High concentrations of Th, Y, Ce and Zr in the granite-gneisses imply derivation from S-type granites. It is likely that their high heat production capacity maintained the high temperatures needed to transport gold in the hydrothermal systems. It is most probable that the mineralisation dates from the Pan-African orogeny (650-450 Ma)

Apr 1, 1996

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems in¬clude: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of en¬vironmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental dif¬ficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 1, 1980

By Gerhard Derge

THE chemical and physical properties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use, These processes are carried out at high temperatures and involve such complex chemical systems that fundamental scientific knowledge of the properties and behavior of these slags is inadequate. Various hypotheses have been proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenck1 and the recent papers of Chipman and co-authors.2-5 Another proposal is that these compounds dissociate by completes or partial ionization, the evidence for which has been reviewed by Martin and Derge.7 Whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: I, Studies of solidified slag samples by X-ray diffraction, petrography, and similar methods that can be used at room temperature, The correlation of this information with the high-temperature properties of the molten slag is uncertain, 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature, However, even these data present problems of interpretation because they require a complete knowledge of the metal phase, 3, Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret, Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information, The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems CaO-SiO2 and CaO-A1203-Si02 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1946

By J. M. Mutmansky, A. Wang

This paper defines the elements of a basic economic model for decision-making when considering a methane drainage system for an underground coal mine. A drainage system will require significant capital and operating expenses; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision-making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision-making are provided for an actual mine decision.

Feb 24, 1997

By Megan Badonie, Devlon Shaver, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Critical minerals are becoming more important in our technological society because they are used in many of our electronic devices, batteries, and magnets. In New Mexico, low to moderate concentrations of critical minerals are found in Late Cretaceous coal and related strata in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, REE, and Critical Minerals) program. The New Mexico coal, humate, and clinker deposits are relatively low in REE (<325 ppm TREE), Li (<90 ppm), V (<168 ppm), Co (<51 ppm), Ni (<108 ppm), Zr (<557 ppm), and many other critical minerals compared to normal economic deposits. Some of these rocks are enriched in Al2O3 (<40%) and Sr (<3740 ppm), both critical minerals. Common minerals hosting the critical minerals in these rocks include clay minerals, zircon, and rutile/anatase. As the demand for some of these elements increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Ultimately, economic potential will most likely depend upon production of more than one commodity, maybe even from coal, humate, and clinker deposits.

Feb 1, 2024