Search Documents

Jan 1, 1882

By C. W. Davis

AN inclined shaft is usually more difficult to sink than a vertical shaft, yet it is often chosen because of the subsequent saving in cross-cuts required to reach an inclined ore body. This paper briefly discusses the factors which led to the choice of an incline and then describes the operations involved in the preparatory work and in the sinking. These operations included a programme of mining out the underground facilities and installing the structures required for a hoist-room, cable-raise, waste-pass, ore pass, two sets of skip dumps, and a collar station equipped with counterbalanced drop-rails. The shaft was sunk 1,000 feet and four stations were cut, each with loading pockets. As the sinking progressed, the rock changed from hard porphyries and dense cherts to blocky limestones and earthy rubble. These conditions called for a change in methods and it is to the red it of the shaft-sinking crew that they overcame the new difficulties as the shaft progressed, while maintaining a satisfactory monthly advance. The section mined out was nine feet six inches by seventeen feet overall. This gave room for three compartments: two skip compartments four feet three inches by five feet nine inches inside the timber, to handle two-ton skips, and a manway three feet six inches by five feet nine inches. The sinking began on December 16th, 1941, and was completed on February 15th, 1943.

Jan 1, 1945

By Richard A. Thomas, Liming Yuan, Wei Tang, JOHN SOLES

Lithium-ion (Li-ion) battery applications are increasing for battery-powered vehicles because of their high energy density and expected long cycle life. With the development of battery-powered vehicles, fire and explosion hazards associated with lithium-ion batteries are a safety issue that needs to be addressed. Li-ion batteries can go through a thermal runaway under different abuse conditions, including thermal, mechanical and electrical abuse, leading to a fire or explosion. The National Institute for Occupational Safety and Health (NIOSH) mining program is conducting research to prevent and respond to lithium-ion battery fires in battery-electric vehicles in the mining industry. In this study, experiments were conducted to investigate the effectiveness of different suppression systems including dry chemical, Class D extinguishing powder and water mist for lithium-iron-phosphate (LFP) battery pack fires. The effects of activation time and release time of the water-mist system on the suppression of the LFP battery (a type of Li-ion battery) fires were studied. The results of this study may be helpful for developing strategic firefighting and response plans for battery-powered vehicles used in mining.

Aug 1, 2024

Researchers at National Institute for Occupational Safety and Health (NIOSH) are investigating how fiber-reinforced shotcrete mix designs can be extrapolated from proven designs employing wire mesh. This paper explains the results of round determinate panel tests and relates the flexural strength and toughness of fiber-reinforced shotcrete to known energy absorbing properties of wire mesh. The energy absorbed with central deflection is strongly influenced by the amount of fibres. The higher the energy absorption the more load cracked shotcrete can support. Two types of fiber-reinforced shotcrete were investigated, one with steel fiber and another with polyfiber. The residual load supported in Round Determinate Panel Tests can be matched with the strength of wire mesh, thus providing equivalent bag strength values for fiber reinforced shotcrete panels. There is also evidence of a panel crack width comparison to the load holding capabilities of the fiber in the shotcrete mixes. In practice, this provides designers with a method for comparing the ground support provided by fiber-reinforced shotcrete with that supplied by wire mesh.

Jan 1, 2010

By N. A. D. Parlee, I. D. Shah

The solubilities of oxygen in liquid Ag-Au, Ag-Pt, and Ag-Pd alloys have been determined in the range of 940° to 1200°C at 1 atm pressure of oxygen using an improved Sieverts technique. The additions of gold (0 to 57 pct), platinum (0 to 27 pct), and palladium (0 to 22 pct) to liquid silver continuously decrease the solubility of oxygen in liquid silver. Activity coefficients and interaction coefficients of oxygen in these alloys and have been calculated. The interaction coefficientscan be described by the following equations: Approximate second-order interaction coefficients (pM have been calculated. The contribution of the product, pMxNM, to In yo only becomes significant at high alloy concentrations. RECENTLY several investigators1"3 have redeter-mined the solubility of oxygen in liquid silver. In general the recent findings1" for Po, = 1 atm are in good agreement with the equation:4 log %O = 695.4/T + 1.086 [1] It is established1, 2 that the solubility of oxygen follows Sieverts' law reasonably well, at least up to 1 atm partial pressure of oxygen. It should be noted that a very slight deviation from Sieverts' law has been reported by Lupis and Elliott.3 Only recently has the solubility of oxygen in Ag-X binary liquid systems received much attention, and only the Ag-Cu, Ag-Au, Ag-Pt, and Ag-Pd systems have been studied. Par lee, Sacris, and zoellners reported that the solubility of oxygen in liquid silver increases progressively with the small additions of copper (0 to 0.5 pct) up to the point where the copper oxide phase appears. Lupis and ~lliott~ have reported that the solubilities of oxygen in liquid silver decrease progressively with the additions of gold, platinum, and palladium. However, their investigation was limited to 0 to 5 pct of these alloying elements, a range too limited to satisfy the requirements of the research program of this laboratory, where the solubilities of oxygen in the range of 0 to 30 pct were required for the calculation of chemical diffusion coefficients of oxygen in these alloys. The present paper deals only with the solubilities of oxygen in these alloys while another paper will deal with the diffusion of oxygen in these alloys. EXPERIMENTAL METHOD A Sieverts technique was employed which involved an improved design of the reaction tube, Fig. 1, as described briefly in a previous communication.4 Liquid melts (70 to 100 g) were held in Norton Alun-dum crucibles. The induction furnace used had a maximum output of 2.5 kw with very fine control. This induction system had excellent stability and the final equilibrium temperatures measured by calibrated Pt-Pt, 10 pct Rh thermocouples are believed to be within ±2C. These thermocouples were checked against the melting point of pure gold wire, and the results agreed with standard tables (±l°C). Each run involved a careful sequence of operations. The sample was heated to and held at about 900°C in vacuum for 3 to 4 hr with the thermocouple in a retracted position. After melting, the melts were usually exposed to a small amount of oxygen (0.5 to 2.0 cu cm) and then degassed slowly for 1 to 2 min to remove any oxidizable volatile impurities such as carbon and sulfur as CO, CO2, SO2, and SO forth. Argon gas was then allowed to enter the system. The protection tube containing the thermocouple was then

Jan 1, 1969

By Burton Atkinson, David Johnston

Evaluation of Ellenburger reservoirs in West Texas has been an uncertain matker at best because of the lack of cores and suitable core-analysis method. Large amounts of oil arc produced from sections from which sample cuttings are obtained that contain litile porosity and no oil saturation. It has long been realized that the formation in some areas contained numerous fractures and solulion cavities that probably contained the major part of the oil present but the magnitude of the porous system conltaining oil has been unknown. Diamond coring cquipmene, used in the mining industry lor many years, has been developed for oil-field use to obtain high core recovery in fractured dolomite that is not possible with conventional coring equipment. A 36ft section of the core recovered from a fractured Ellenburger reseivoir waS analyzed by a unique but simple method to obtain the first defmite evaluation of one section of the producing formation. The cores and the method of analysis used are described and the results arc discussed in some detail. Discussion The first successful known analyses of cores recovered from the Ellenburger formation in the Permian Basin area were made on cores recovered with the use of diamond core heads. Conventionul coring methods previously used have had lour core recovery and standard methods of analysis have proved to be inadequate for evaluation of those cores that were recovered. Core Descriplion The Ellenburger formation to be dis cussed was cored using diamond core heads and oil-base drilling fluid. Of the total 103 ft cored to a depth of 8893 ft in the Ellenburger, 99 ft or 96 pct was recovered. The dolomite cores were described as gray to white, crystalline to coarscIy crystalline, with chert and calcite inclusions. Occasional shale partings ? to ¼ in. in width were noted. A small amount of green clay was found in some of the coarsely crystalline material. So intergranular porosity was found by inspection in any of the cores. The core urns highly fractured over most of its length with not more than two continuous feet that failed to contain fractures. The fractures Were nearly vertical and varied in width from those harely visible to as much as one millimeter. Scattered solution voids, or vugs, as large as 3 cm in diameter occurred in association with same •a

Jan 1, 1949

By Harrison Schmitt

The definitions of the terms commonly used in connection with metamorphism at elevated temperature near igneous contacts are re-examined. As the study of tactite zones associated with igneous contacts progresses, more and more emphasis is put on the localization of the ore by structural forms. The generally early age of the silicates and late age of the sulphides is well established. Postsilicate structural deformation is likely to localize ore bodies. The silicates are often replaced by the ore minerals. we may not be far from proving that the elements involved in the formation of silicate aureoles are merely normal "volcanic" emanations, that silica, lime, magnesia, and alumina, and probably soda and potash, are likely to undergo local transfers only. The work of Newhouse suggests the agents of the formation of sulphides in deposits of various classifications are the volcanic emanations. Introduction The purpose of this paper is to define the terms commonly used in connection with the subject, to briefly review and discuss the broad features of the aureoles, to indicate some of the features lately recognized: to discuss the genesis, and to suggest how the associated ore deposits can best be studied and developed. When developing a subject in mining geology one is soon conscious of the vast amount of pertinent literature and that most relevant ideas, no matter how obscure, have been considered. One can only hope to make some small contribution in point of view, a few confirmatory observations, or, perhaps, suggest a small new idea indebted to the most recent data. It is nearly impossible, also, to give specific credit, and adequate credit, to all the contributors to a given subject. This study, furthermore, was not intended to cover the field exhaustively, nor is the bibliography complete. Definition OF Terms There is much confusion in the use of the broad terms concerned. Needless to say, metamorphism means change of form; metasomatism, change of substance. The term contact metamorphism, however, has been widely misused possibly by a majority of economic geologists and engineers. As originally adopted by European investigators it meant changes effected largely by heat (thermal effects) in the rocks invaded by plutonic intrusives, but did not include those local changes usually at the immediate contact brought about by the addition of substance, i.e., by metasomatism. The term has become clouded. In Europe it has

Jan 1, 1949

By Harrison Schmitt

The definitions of the terms commonly used in connection with metamorphism at elevated temperature near igneous contacts are re-examined. As the study of tactite zones associated with igneous contacts progresses, more and more emphasis is put on the localization of the ore by structural forms. The generally early age of the silicates and late age of the sulphides is well established. Postsilicate structural deformation is likely to localize ore bodies. The silicates are often replaced by the ore minerals. we may not be far from proving that the elements involved in the formation of silicate aureoles are merely normal "volcanic" emanations, that silica, lime, magnesia, and alumina, and probably soda and potash, are likely to undergo local transfers only. The work of Newhouse suggests the agents of the formation of sulphides in deposits of various classifications are the volcanic emanations. Introduction The purpose of this paper is to define the terms commonly used in connection with the subject, to briefly review and discuss the broad features of the aureoles, to indicate some of the features lately recognized: to discuss the genesis, and to suggest how the associated ore deposits can best be studied and developed. When developing a subject in mining geology one is soon conscious of the vast amount of pertinent literature and that most relevant ideas, no matter how obscure, have been considered. One can only hope to make some small contribution in point of view, a few confirmatory observations, or, perhaps, suggest a small new idea indebted to the most recent data. It is nearly impossible, also, to give specific credit, and adequate credit, to all the contributors to a given subject. This study, furthermore, was not intended to cover the field exhaustively, nor is the bibliography complete. Definition OF Terms There is much confusion in the use of the broad terms concerned. Needless to say, metamorphism means change of form; metasomatism, change of substance. The term contact metamorphism, however, has been widely misused possibly by a majority of economic geologists and engineers. As originally adopted by European investigators it meant changes effected largely by heat (thermal effects) in the rocks invaded by plutonic intrusives, but did not include those local changes usually at the immediate contact brought about by the addition of substance, i.e., by metasomatism. The term has become clouded. In Europe it has

Jan 1, 1949

By Mario Sanchez, Jose Palacios, Fernando Parada

Carbon steels have less than 0.02% copper and have low atmospheric corrosion resistance. The addition of at least 0.20 wt% Cu improves this property. Also, 0.8 wt% Cu in steel shows a hardening potential for developing high strength corrosion resistant steels. Copper slags containing 42–45% of iron, silica and minor amounts of copper were used for producing Fe–Cu alloys by reducing the oxides contained in the slag to obtain a Fe-0.84 wt% Cu alloy, which could be suitable as feeding material to manufacture a corrosion resistance steel, and also would be an alternative for minimizing the copper industry ’s environmental impact, and to introduce the application of the Circular Economy concept to the natural resources exploitation, especially in countries where their economy is strongly based in mining and metallurgical extraction.

Mar 1, 2018

By K. Gao, R. Dry

"Carbon boil, which results in excessive spitting and even complete destruction of a metal drop, could significantly influence the efficiency of direct smelting processes. Carbon boil has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure, and melt area/volume ratio. The time of carbon boil was determined using a CCO camera coupled with a time/date generator connected in parallel to a video recorder and a computer. The time of carbon boil was in the range ~5 - 15 seconds under the conditions in this study. A mechanism for carbon boil has been proposed.IntroductionThe occurrence of carbon boil in molten iron drops can result in excessive spitting and sometimes even complete destruction of a metal drop. In direct iron smelting processes, this could significantly influence the decarburisation of liquid metal and the post combustion and hence may influence the efficiency of smelting processes. The generation and consequent ejection of metal droplets into the gas phase occurs due to the intense turbulence in the bath which results from the injection of gases and coal. The aim of this investigation is to understand the fundamentals governing the carbon boil phenomenon under direct iron smelting conditions to assist control of process efficiency.Carbon boil phenomenon has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure and melt area/volume ratio. The time for the occurrence of carbon boil has been determined in this study at 1440 °C using a novel approach which includes utilisation of a CCD camera coupled with a time/date generator connected in parallel to a video recorder and a computer. This arrangement permits the capture of the entire sequence of events leading up to carbon boil and therefore the determination of time of boil which is in the range -5 - 15 seconds under the conditions in this study."

Jan 1, 1996

By W. M. Kidd

INTRODUCTION Uranium mine inspection in Canada forms one element of the enforcement of the Atomic Energy Control Act; it is under this Act that all Canadian uranium mines and mills are licensed to operate. Inspection duties are carried out by a small core staff of federal government inspectors (working for the Atomic Energy Control Board (AECB)) largely supplemented by provincial mine inspectors working on behalf of the AECB. Unlike most resource extraction in Canada, uranium mining is under federal jurisdiction and consequently it was the AECB who decided in 1975 that changes in the Canadian uranium mining industry, particularly its expansion and the expanding role of the mine inspector in the limiting of exposures, warranted the offering of a special radiation protection training course. The Uranium Mine Inspector Training Course (UMITC) was first conducted in 1976 at the Elliot Lake Centre in Elliot Lake, Ontario. Subscription for the course was not limited to mine inspectors to enable union stewards, management personnel and provincial/federal labour inspectors to attend. This paper will present an outline of the course content, the format of its presentation and non-curriculum aspects of running a course of this type in uranium-producing community. The core lecturers for UMITC are drawn from the Radiation Protection and Uranium Mine Divisions of the AECB. In addition, guest lecturers are invited from universities and medical research centres together with industry professionals and government researchers. In all some twenty-four plus presentations are made over the first five days of lectures. The program topic areas, hazards, controls, measurements, record-keeping and health effects are preceded by an intensive half-day session on radiation fundamentals. TOPICS Hazards [Dust] A review of the dynamics of airborne particles including the effects of particle size, gravity and wake-turbulence on the behaviour of dust clouds. Associated topics are migrational aspects of dust particles and specific dust-generating mine operations. [Radiation] Canadian uranium mines are increasingly diverse in nature ranging from large scale low-grade underground operations in Elliot Lake to smaller high-grade open pits in Saskatchewan. Papers are presented on assessments of internal and external exposure, the metabolic pathways of ingested or inhaled radiation and the specifics of mine and mill hazards. Radiation hazards are further broken down into gamma surveys of uranium mines, radon daughter concentrations and problem areas. Controls The relationship between mining methods and the operating environment is critically important to ensuring safe working conditions. This refers to both the selection of machinery/devices, etc., and to engineering controls which are instituted to remedy problems created by new technology. UMITC examines a number of possible mining techniques, their criteria for selection and impact on the working environment. Control measures, ventilation practices and design, the need for continuous water misting and special open-pit precautions are presented. These lectures frequently conclude with suggestions for better operating guidelines for mine ventilation systems and the need for greater co-operation between the ventilation department and the underground crews. Measurements Uranium mining regulations stress the need for a high standard of exposure monitoring, statistical planning and record-keeping. [Statistics] Although many course participants are well versed in statistics, certain fundamentals are repeated and include, the concepts of mean, variance, standard deviation and standard deviation of the mean. Confidence levels, decision-making based on sample statistics and statistical records are also discussed. [Dust Measurement] Dust measurement is particularly critical in the mines where the high silica content of the ore body, such as those at Elliot Lake, results in the continuous generation of dust. Sampling practices, filtration, impaction, thermal impaction and electrostatic precipitation are explained together with the methods of counting samples to determine free silica. Konimetric and gravimetric techniques for dust sampling are compared and contrasted. [Radiation Measurements] Both collective and personal dosimetry systems are used in the Canadian uranium mining industry and lectures are presented on each. Techniques and possible sources of error are discussed for a variety of radon and radon daughter measurement methods - Lucas method, Tsivoglou and modified Tsivoglou, Kusnetz, Rolle. Instant working level meters and personal alpha dosimeters are explained in terms of calibration, maintenance, readout and estimation of accuracy. A lecture outlining dose estimation by means of bio-assay, whole-body counting and the use of TLD's concludes the topic. Record-Keeping An overview of the problems of changing limits,

Jan 1, 1981

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006

By Jeffery L. Kohler

A method of monitoring production, information, i.e., raw tonnage and machine state, from each working section has been developed. The method is based on the sensing of electrical parameters in each section load center, and the reporting of this information through the existing mine-wide monitoring system. A decision-theoretic type of pattern classification technique has been used to define the machine states. The basis of the method is presented in this paper, along with a proposed hardware and software implementation scheme. Information issues central to the development and use of the proposed production monitoring system are also discussed.

Jan 1, 1988

By James J. Bryja, Thomas M. Barczak, Dennis R. Dolinar, Joe Bower, Thomas P. Mucha

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial and error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground, reaction behavior based on the support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health (MOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate -- application of alternative roof support systems or to design in- mine trials such that a fair and equitable comparison of different support systems can be made. A case study if the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to conventional wood and concrete cribbing historically used at this particular mine.

By F. M. Doyle, Robert G. Robins, E. Peters

Stability diagrams for the Cu-S-H2O system have been widely applied over many years. Stability diagrams for aqueous systems generally, have been generated by computer, but with the programs for Potential-pH diagrams in particular, a common routine leads to error in multi-element systems. In this paper these errors, and some misinterpretation of diagrams are considered. In most of the published diagrams for the Cu-S-H2O system there has been no account of the sulfide complexes of copper. Here, the free energies of formation for the various species in the system have been re-evaluated for consistency, and some diagrams for the Cu-S-H2O system ( generated with the program DIASTAB Vers.5 ) are presented.

Jan 1, 1993

By S. P. Song

A computational methodology based on the coupled finite element and boundary methods is developed to predict the free surface shapes of electrically conducting liquids supported by the electromagnetic field. The work is an extension of our previous FEIBE model for induction calculations. The free surface algorithm is developed using the Weighted Residual Method, the very same used for nonlinear finite element formulation. This allows the treatment of field computation and free surface prediction in the same manner, thus making easier the formulation of the magnetically-supported free surface problems. Like other nonlinear algorithms, the boundary/finite element free surface scheme is also iterative owing to the fact that free surface shapes are unknown a priori. But the numerical scheme is robust and efficient and is capable of handling rather complex free surface deformations. Computational algorithms will be given and are tested by comparing with other solutions whenever available. Computed results of magnetically-supported free surface shapes are presented for magnetic levitation under microgravity and floating zone refining processes under normal gravity.

Jan 1, 1996

By J. Keith Haddock

"IntroductionThe Bienfait Mine is operated by Bienfait Coal Company Ltd., one of the Luscar Limited group of companies. Situated 5 km southeast of the town of Bienfait, Saskatchewan, it can produce 2.0 million tonnes of lignite annually in addition to 158,000 tonnes of char from a carbonization plant located on the property. Geology The economically mineable coal seams of the Estevan area are found in the Ravenscrag Formation. The lignite-bearing sands, silts and clays were deposited in Early Tertiary age, in an inland sea centred in the Williston Basin of North Dakota. The top of the Ravenscrag is an erosional surface, overlain by Tertiary or Quarternary sands and gravels or glacial till. The regional structure is a gently plunging syncline which dips to the southeast at about 0.3 degrees. There are minor undulations in the Bienfait area which are due to differential subsidence during deposition. Sporadic faulting is probably a result of glacial pressures, and preglacial and glacial channels are responsible for washout zones and the abrupt irregular subcrop found in the area. There are two economic coal seams in the Bienfait area, an uppe; seam locally known as the Roche Percee, and a lower seam, the Estevan. Both seams have been extensively mined since lignite mining began in the area in the late 1800s. The Roche Percee remains only in a small portion of the Bienfait Mine and comprises a very minor portion of the reserves. It averages 1.74 m thick under 8.1 m of overburden. The till rests on top of the Roche Percee and due to weathering the seam is generally of poorer quality. The Estevan seam comprises the majority of reserves at Bienfait. The main seam which is being worked on consists of an upper bench averaging 2.75 m, a carbonaceous parting of 0.21 m, and a lower bench of 0.92 m. Overburden depth above this seam varies from 21.0 m to 38.0 m."

Jan 1, 1985

By Christina Viklund-White

Life Cycle Assessment has been used to compare the environmental performance of landfilling versus recycling of the zinc used for galvanizing steel. Hypothetical process routes were com-posed involving four different EAF dust treatment processes; Waelz kiln, DC-furnace, EZINEX and slag fuming, as well as scrap dezincing. The study shows that recycling of zinc used for galvanizing steel has environmental benefits in that it saves zinc resources. However, zinc recovery does not necessarily decrease the potential impact on global warming and acidification. The magnitude of these two impact categories is tightly correlated with the amount and type of primary energy consumed in a process. Due to the high electricity consumption in the dezincing process, this route has the highest impact on Global Warming Potential as well as Acidification Potential. The major part of the energy requirement for the production of zinc from primary and secondary sources is consumed in the reduction of ZnO to Zn. The consequence is that the theoretically possible savings in primary energy by recycling zinc-containing materials are relatively minor. The impact categories "land use" and "waste generation" are not considered in this study, but most likely the evaluation of such impacts would further increase the potential environmental impact of the landfill alternative. The results also show that the location of an electricity-intensive process highly affects the potential environmental impact. Comparing process and material alternatives in LCA studies where branch average data is used, is considerably more complex than when LCA is used within a company.

Jan 1, 2000

By Mariana H. Staia

The present communication reports the results obtained by applying different concentration methods, at laboratory level, to the black sands from Estado Bolivar, Venezuela, with the aim of obtaining an adequate ilmenitic concentrate for the subsequent chlorination process. Sizing analysis was performed and plasma emission spectroscopy method was used to determine the chemical composition. It was found that from the two hydrogravimetric methods used, the Humphrey spirals is much more effective than Wilfley tables, leading to a 85% recovery. The most convenient particle size group for these concentration methods was the one corresponding to ASTM 40-140 mesh. When magnetic concentration was applied to the concentrate, obtained as a product from Humphrey spiral, a recovery of ilmenite more than 90% was obtained in the first step. It has been shown that the ore would respond to the separation techniques employed, giving individual minerals: ilmenite, zircon and silica as concentration products.

Jan 1, 1995

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"Direct digital manufacturing offers promise as a technique for fabricating complex hydrogen purification membrane support structures. Free form fabrication methods can produce parts with complex structures, and sintering parameters can be controlled to adjust the density, pore structure, pore pathways and strength in catalytic substrate constructs. Efforts are underway to define the influence of selected process variables on the chemical and mechanical properties.IntroductionThe Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production. Because hydrogen readily passes through palladium, a structurally sound palladium-based membrane is capable of separating relatively pure hydrogen from other gases. In order for this technology to succeed, a suitable substrate material must be identified.High purity hydrogen is produced by various means. A common method involves a two-stage process for separating hydrogen from a hydrocarbon gas stream: 1) hydrogen-rich syngas is produced by the catalytic reaction of natural gas or another light hydrocarbon gas with steam, and 2) hydrogen is separated from the other syngas components by pressure swing adsorption (PSA) (US. Energy Information Agency, 2011). In PSA, gases enter a column that is packed with a material that absorbs gases as the chamber is filled and pressurized. As the pressure is slowly relieved, the absorbent material releases hydrogen at a higher pressure than the impurity gases. PSA processes produce 99.99% pure hydrogen at a high recovery rate. These systems typically demand a high capital investment due to the high pressure and multiple stages (columns) needed to attain high hydrogen production rates.Research geared toward reducing hydrogen production cost is focused on the development of improved catalysts and adsorbent materials as well as more effective single-stage separation processes. An interesting method combines hydrogen reduction catalysis and filtration. Nascent hydrogen is separated from other gases as it selectively permeates the filter. Catalyst filters may be made of gold, silver, platinum, palladium or precious metal alloys (Davis, 2009)."

Jan 1, 2012