Search Documents

By D. Imeson, T. Grammatikopoulos, G. Pearse, M. Aghamirian, C. Mohns

"Spodumene mineral is a source of lithium for lithium ion batteries. Thus, the production of a spodumene concentrate with an approximate grade of 6% Li2O is targeted. Traditionally, spodumene is concentrated by froth flotation using fatty acid as the collector. Amine collector can also be used to float mica ahead of spodumene as required or feldspar from the spodumene tailings. Slimes have a negative effect on spodumene flotation and they are commonly separated by scrubbing and de-sliming prior to spodumene flotation. The main losses in spodumene flotation typically occur in cyclone overflow, scrubbing slimes, spodumene flotation tailings and mica concentrate. In recent years, dense media separation (DMS) is the main concentrating process in Australian spodumene operations. In these operations, DMS is efficient at generating coarse grain concentrates and rejecting large portions of silicate gangue, thereby directly reducing the milling cost. The ore should be crushed to 3/8” or coarser while further crushing is possibly necessary on the middling particles to scalp further spodumene. The DMS feed should be classified to remove fines (typically -0.5 mm particles). The final middlings and undersize fractions could then be processed by flotation. The main requirement in DMS operations is to have good spodumene liberation at relatively large grain size. This paper reviews the most significant DMS and flotation parameters in spodumene beneficiation. The treatments of different minerals in the spodumene ore are also addressed.INTRODUCTION A number of laboratory/pilot plant programs have been recently conducted at the SGS Lakefield site, sponsored by different clients. The main objective has been to develop a process flowsheet to generate a spodumene concentrate containing 6.0% or higher Li2O (~75% spodumene) suitable for producing lithium carbonate by a hydrometallurgical process. Depending on spodumene liberation size, dense media separation (DMS) can be an attractive option to produce a final high grade concentrate and to reduce the mass to be treated in the flotation circuit. In such a case, crushing would typically be performed in stages, with DMS separation to recover a spodumene concentrate and reject gangue minerals following each stage. DMS middlings and -0.5 mm fines can be processed by flotation to further recover spodumene. In the flotation process, coarse stage grinding minimizes the grinding cost and formation of slimes. In the majority of cases, a grind size (K80) of approximately 200 microns is sufficient for flotation. After primary grinding, mica, if present in an appreciable amount, should be floated to minimize interference with spodumene flotation. Desliming after scrubbing and high density conditioning are the key process operations prior to spodumene flotation. Spodumene can then be floated from silicate gangue minerals with a fatty acid or a mixture of fatty acid and petroleum sulfonate at slightly alkaline pH. Subsequently, feldspars can then be floated from the spodumene tailings."

Jan 1, 2012

By N. M. Stubina, P. J. Lind

Barrick Gold is in the process of building several new mines and implementing new processes at existing mines for which metallurgical technology is of key importance. The roles of the company's Strategic Technology Solutions team and the Barrick Technology Centre are discussed within the context of their responsibilities within Barrick's Operations Support group. The paper will present an overview of the development of the technology centre from the former Placer Dome Research Centre to its current form supporting strategic technology, capital projects, and operating sites. Novel approaches to research and development will be presented as well as an overview of some of the technologies developed from bench-scale to pilot-scale, and beyond.

Jan 1, 2011

Evver since it first displayed an autonomous mining truck at the 1996 MinExpo show in Las Vegas, NV, Caterpillar has been building the blocks to a fully autonomous mine. In May, the company unveiled another block in that progression, the new Cat MineStar System that it says is ?the industry?s broadest, most comprehensively integrated miner operations and mobile equipment management system.? The full system is comprised of five capability sets ? Fleet, Terrain, Detect, Health and Command ? to help operators define the size and scope of their management system based on the needs of their mining operations. Michael Murphy, technology and autonomy manager for Cat Global Mining, explained that the customers were not ready for an autonomous mining truck in 1996, but that many customers wanted the building blocks to eventually get to autonomous mining. After 15 years of work, Murphy said the building blocks have come together in the form of the Cat MineStar System.

Jan 1, 2011

By C. Ek

Tailings originating from the gravity concentration of a gold ore containing about 14 g/t Au have been treated by various beneficiation methods. These tailings have been screened on the 147 and 74 micron sieves and the two coarsest fractions have been separated on shaking tables with unsatisfactory results, but the concentrates have been examined in polished sections for mineragraphic analysis. Very simple flotation flowsheets have been applied to collect most of the gold, recovery and grade varying with the regrinding time in a ball mill. Cyanidation tests have shown that this type of treatment is also applicable to such tailings.

Jan 1, 1991

By P G. Gaylard

P754 has been an unusual project in that its main aim was to develop a code of practice for metal accounting with the following key objectives:Development leading to an agreed industry standard at corporate governance level Significant improvement of the credibility of metal accounting from deposit to saleable product Development of guidelines for data collection, data analysis, reporting and audit A data analysis toolbox which provides go/no go testing for metal balance data Promotion of industry adoption of these guidelines to improve transparency and financial credibility. Over time, these guidelines may evolve into a code and eventually into a standard Develop and train engineers to become expert in metal balancing and reporting. Papers like this one and the workshop which follows this conference are part of promoting the code for adoption by industry. Developing a code of practice has traditionally been the provenance of professional bodies associated with particular industries û often on a voluntary basis. Given todayÆs industry pressures, it was felt that funding key input might accelerate the development process as well as offer opportunities to research some of the problems and to train some post graduate students in a difficult discipline. In fact, the project has brought together six industry sponsors from a wide range of process types, three research providers, and funded students in South Africa and Australia. The project has also attracted input from the financial community. A textbook to support the application of the code has also been written. The industry sponsors have made the Code and Guidelines available on request to help to facilitate its use by the mineral industry beyond the sponsor group. The Code and Guidelines have already been translated into Spanish and Portuguese which suggests that industry acceptance may happen quite quickly. The main thrust of the code is to integrate commercial and technical performance to a much higher degree. The Check in-Check out (CI-CO) method has been chosen as the vehicle for this combined approach. The mass and metal values used for CI-CO are 'absolute' and provide the basis of financial transfers. The CI-CO process occurs at each transfer of custody - whether between divisions within a company, or between companies. This approach means that measurement of mass and metal flows becomes the critical element of the process and that a quantitative knowledge of measurement accuracy and precision is also essential. This knowledge allows technical differentiation between differences which are within the expected margin of variation and those which must be formally identified as discrepancies and subject to a process of investigation and sign off. Hence, the application of the code for most companies should be more evolutionary than revolutionary, but with substantially more emphasis on measurement and definition of measurement error. Where this can be achieved, it should bring the mineral industry more into line with other industries competing for investment funds, community acceptance and future employees.

Jan 1, 2008

By R. L. Solmer

During 1959-61, the Bureau of Mines investigated the strain and deformation induced in rock and concrete linings around mine openings by retreat panel caving at the Climax Molybdenum mine. Two concrete-lined slusher drifts on the Phillipson level of the mine were instrumented with both electrical strain gages and extensometers. Changes in strain and deformation were recorded over an 18-month period during the undercutting and caving of the mining panel. General agreement was found between the strain and deformation measurements and the hypothesis that the vertical component of the stress field on the openings is almost completely removed by undercutting. This phenomenon is a possible explanation for the structural failures that occur in the slusher drifts during the undercutting cycle.

Jan 1, 1965

By Joseph Hamuyuni, Fiseha Tesfaye, Daniel Lindberg

E-waste management through traditional methods such as disposing in landfills, burning in incinerators or exporting abroad for disposal are no longer options due to the strict environmental regulations. Fortunately, the presence of valuable metals in the e-waste and increasing demand for the metals as well as complexities of the currently available primary raw materials make recycling an attractive and viable option both environmentally and economically. Moreover, it is efficient in terms of resource management by closing the loop of metals. Consequently, urban mining such as the recovery of precious metals from e-waste streams through sustainable recycling processes have emerged. The sustainable recycling practices address the scarcity of primary resources and reduce consumption of energy for metals production while managing environmental issues related to hazardous materials from the e-waste streams. In this paper, valuable metals recoveries from e-waste streams through pyrometallurgical and hydrometallurgical processes are critically reviewed. And, innovative ideas for different steps of the thermochemical processes in the valuable metals and energy recovery from the e-waste streams are discussed.

Mar 1, 2017

By Nicholas J. Grant, Robert H. Kane, Bill C. Geissen

The platinum-rich section of the Ta-Pt Phase diagram was worked out by metallographic and X-ray techniques, using twenty alloys; solidus temperatures and solid solubilities were determined. Besides s phase, four intermediate stoi-chiometric phases were found: TaPt (high-temperatzrre phase, structure unknown); TaPt2 (ortho-rhomhic, new type); a TaPt3 (orthorhombic, TiCu3 type); ß TaPf3 (monoclinic, new type). TaPt2 and TaPt3 melt congmentlv; two eutectic, two beritec-tic, and one eutectoid reactions occur in the inuestigated range. THE Ta-Pt system was examined as part of a study of the phase diagrams and the intermediate phases of niobium and tantalum with Group VIII transition metals. Since the main scope of this work was the relation among the ordered close-packed phases occurring in the concentration range from AB to AB3 (A = Nb, Ta; B = Pd, Pt, and so forth), only the platinum-rich side of the diagram was worked out thoroughly, while spot checks were made to determine the approximate outline of the tantalum-rich portion. The system has not been thoroughly treated in the literature; Greenfield and Beck1 in their survey of refractory metal intermediate phases found a o phase between -18 and 37 at. pct Pt which coexists at higher platinum concentrations with an unidentified intermediate phase. Browning2 worked on the range between 55 and 100 at. pct Pt; however, this preliminary study did not cover temperatures >1500°C, and included no conclusive crystallo-graphic data. More recently, a study of the platinum-rich section of the Ta-Pt system has been carried out by Ray,3 while Hartley, Parsons, and steedly4 have studied the tantalum-rich section. The crystal structures of TaPt2, a TaPt3, ß TaPt3, and others have been reported in abstracted form by Giessen and Grant.5 EXPERIMENTAL METHODS The methods of alloy preparation and processing and of the metallographic and X-ray procedures follow very closely those described by Ritter, Giessen, and rant' for other refractory metal-noble metal systems, and will not be repeated except where significant differences exist. Starting materials were: tantalum rod of 99.95 pct purity, supplied by National Research Corp., and platinum sponge 99.9 pct, supplied by The International Nickel Co. An oxygen analysis of the tantalum rod showed 30 ppm O; other impurities were C, N, Si, Nb, Mo, none of these exceeding 50 ppm, and 100 ppm W. Homogeneous buttons were readily prepared as follows: ingots of 5 g were weighed and arc-melted under welding grade argon, followed by two remelts after inverting the button. Between 40 and 100 at. pct Pt, weight losses during the first melt rarely exceeded 0.1 pct, in which case the alloy was rejected, and were nil on subsequent remelts. Since the vapor pressure of platinum far exceeds that of tantalum, the small evaporation loss could be assumed to consist of platinum; therefore, a corresponding amount of platinum was added on the second melt. Since it was confirmed on pure tantalum samples that no weight gain through oxygen or impurity pickup occurs (see Ref. 71, it could be assumed that the uncertainty in the composition did not exceed ±0.1 at. pct for the range 40 to 100 at. pct Pt. For the four control melts from 0 to 40 at. pct Pt, an error of ±0.5 at. pct was calculated. Microscopic examination of the whole buttons after melting showed no inhomogeneity other than local coring. This was eliminated by a homogenization heat treatment. A total of twenty-three alloys were prepared. Heat treatments were carried out in a tantalum

Jan 1, 1965

By Charles W. Bloomquist

The profitability of miscible flooding in a hypothetical target oilfield is examined. The major costs, including Windfall Prof it Tax, are identified and their re1ative importance are discussed. The sensitivity of profit to important physical and economic variables is evaluated and discussed, including variance in oil recovery, oil price, injectant requirements, injectant cost, and capital requirements. Economic sensitivities to important development and operating decisions such as timing, Spacing, Slug size, and gas recycling are also analyzed. The Windfall Profit Tax (WPT) as it applies to gas miscible EOR projects is reviewed. The effect of WPT on each of the various project cases is analyzed and the effect of reduced WPT on remaining production from existing operations is evaluated. Tax implications are compared for integrated vs. "independent" controlled projects and the alternative of expensing vs. capitalizing tertiary injectants is also evaluated. The impact of the Net Income Limitation in reducing WPT. during early and late project life is determined and discussed.

Jan 1, 1982

By R. Rodgers

The Pinto Valley concentrator of BHP Copper Inc. restarted its sulfide mining operations in September 2007 to produce copper and molybdenum concentrates. During the plant production ramp up, the copper/molybdenum circuit quickly reached the copper grade and recovery targets, but the production and quality of the molybdenum concentrate continued to be a challenge. Even though several improvements in the molybdenum circuit were completed, the final molybdenum concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns were chosen. The column design and construction were done using in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing molybdenum concentrate to the required specifications, that is, high molybdenum tenors and low copper and iron content. The Pinto Valley operations, are comprised of the Pinto Valley concentrator, the Pinto Valley dump leaching and a solvent extraction/electrowinning (SX/EW) plant. The concentrator operated from 1972 to 1998 when mining and milling operations were curtailed for economic reasons. The SX/EW plant continued operations for copper cathode production. After a cessation of mining operations of almost 10 years, Pinto Valley operations began a restart project in January 2007, to bring the mine and the concentrator back into production. Copper concentrate production started in October 2007 after refurbishing and upgrading the facilities with a new DCS system and filter plant. The daily targets of the concentrator were to treat 56.7 kt (62,500 st) of ore, produce 762 t (840 st) of copper concentrate containing 27.5 percent copper at recoveries of 86 percent and produce 2.2 t (2.5 st) of molybdenum concentrate containing more than 80 percent MoS2.

Jan 1, 2010

By T. D. Parris

Within a 30-mile radius of Sudbury, Ontario, the Ontario division of the International Nickel Co. of Canada, Ltd., operates nine underground mines and two open pits. Prior to 1966, ore removal from the underground workings was mainly by scraping, using 125-hp electric slushers in blasthole and caving mining, and 30-hp or less air-operated slushers for fill- method mining. The development and evaluation of low-profile, diesel-powered front-end loaders, designed specifically for underground operations, was followed with keen interest during the period 1964-1965.

Jan 6, 1969

By Stig Eriksson

In Switzerland two major railway systems as shown below in Figure 1 has recently been completed or is under construction: ¦Lötschberg, south of Bern which was commissioned in 2007 ¦Gotthard, south of Zurich which is scheduled to be commissioned in 2016The aim is to increase the transport capacity of the railway system and to transfer more transport of goods to the railway by offering transport of trailers and lorries on the new railway systems. It will have a positive environmental impact but also improve the congested traffic situation of the highways in north-south directionThe Gotthard tunnel is totally 57 km (35 mile) long and the Lötschberg tunnel is 35 km (22 mile) long. Both tunnel systems consist of two parallel single track tunnels connected with cross tunnels at every 333 m (1 093 ft). Additionally there are cross-over tunnels and caverns for installations and operation. In the Lötschberg tunnel, the majority of the excavation has been by Drill & Blast and in Gotthard tunnel the major part is being excavated by TBM.

By Erwin K. Roesner

The difficulties encountered while sinking deep shafts for Potash Mines in southern Saskatchewan have been the subject of several papers in the past. Geological and hydrological conditions of the strata overlying the potash deposits require special techniques for ground and water control during shaft sinking. The easily soluble potash ore requires the lining of these shafts to be virtually watertight to assure long term and safe operation. This paper describes the construction of the most recently completed potash shaft for the Potash Corporation of Saskatchewan. The shaft was designed and constructed by Thyssen Mining Construction of Canada Ltd. and it is located near Lanigan, approximately 110 km east of Saskatoon.

Jan 1, 1980

Eliminate the need for roof bolter operators and their helpers to work under unsupported roof while setting or removing temporary supports before or during the roof bolting cycle-a task that annually accounts for approximately 20 percent of all roof fall fatalities. Approach The Bureau of Mines designed, built, and field tested an auto-mated temporary roof support (ATRS) that can be carried from place to place on the drill head of a single, fixed-head roof bolting machine (squirmer) used in low coal seams (less than 42 inches thick). How It Works The ATRS is designed for installation on any streamlined squirmer. It consists of a ten? foot-long, steel, wide-flange beam supported by two double-acting, telescoping hydraulic cylinders. A steel sleeve, mounted on the bottom center of the beam, is designed to fit over top of the

Jan 1, 1983

By Gary Pattrick

A new class of spongy Au catalysts is studied for the selective catalytic reduction of NOx by propene under leanburn conditions. The spongy catalyst is an unsupported powdered Au that consists of micrometer particles (~5 microns) that have nanometer scale (~10 nm) internal skeletal structures. The effects of alloying 1 ? 50 atom % platinum group metals (M= Pt, Pd, Rh) and 5 wt% first row transition metals (M = Ti, Mn, Fe, Co) were studied. Even low additions of PGMs (1 at.%) cause significant shifts to lower temperature regions of activity and the largest shift is obtained for Rh. For Rh this is interpreted as a strong synergistic interaction between Rh and Au. Possibly related to the Rh effect, Co is the only other metal studied that lowers the temperature of NOx reduction. The other first row transition metals inhibit the reduction reaction.

Oct 1, 2003

By James R. Welty

Heat content values were experimentally determined for yttrium metal between temperatures of 400° and 1,300° K and for iron pentacarbonyl between 301° and 380° K. The drop technique was used; that is, a sample of material sealed in a protective capsule was heated to 3 desired temperature in a furnace and then dropped into an ice calorimeter. A revised technique for determining heat content values from calorimetric data is described. Heat content and corresponding entropy-increment data above a reference temperature of 298.15° K are presented in tabular form. Equations for heat content and heat capacity as functions of temperature were derived for each substance. These equations are [Y (c): HT-H298.15 = 1.2041T 1 3.393 x 10-3T2- 0.4176 x 10' T"1 + 739.9 cal/mole Cp = 1.2041 + 6.786 x 10-3T + 0.4176 x 106-T-2 cal/deg mole Fe (CO) E, (1) : HT - H298.15 = 55.636T - 16,588 cal/mole Cp = 55.636 cal/deg mole]

Jan 1, 1963

By Arcy R., D&apos George

Removal of S02 from smelter gases is being investigated, using an innovative technique that results in the almost simultaneous recovery and production of elemental sulfur. S02 is removed from the gas stream by scrubbing with suitable aqueous salt solutions or high-boiling organic fluids. The S02-laden liquor is then reacted with H2S Crystalline, high-purity sulfur is instantly precipitated and, after filtration, the regenerated liquor is recycled. The H2S required for the process is produced by reacting a portion of the recovered sulfur with hydrogen or with methane and steam. The chemistry and results of preliminary laboratory research are discussed.

Jan 1, 1969

The Directional Drill Monitor (DDM) is an advanced instrument for real time in hole surveying. It was developed by Du Pont (Australia) to suit Australian gassy coal mining conditions. The instrument consists of three units: i. Down hole transmitter ii. Acoustic transducer iii. Data receiver processor unit (i.e. up hole unit). This paper describes the function of each unit in detail and highlights the importance of the DDM in long hole drilling efficiency. Surveying is carried out independent of hole depth. Each survey takes 2-3 minutes to complete, the frequency of surveying to control borehole trajectory is determined by the accuracy required for a particular hole.

Jan 1, 1992

By B. M. Kunar, C. S. N. Murthy, B. Rao K

Rock particle size has a very important significance in the mining industry, starting from blasting till the mineral processing. The present study was carried out to understand the particle size distribution in various sieves after conducting the ball milling process. The time of the grinding process was varied at different intervals. It was observed that 80% of the particles of both granite and marble rock samples passed through the 4800 μm sieve when subjected to grinding time of 40 minutes. Also, it was observed the number of particles that were retained in the smallest sieve of <75 μm was higher in the case of granite sample when compared to a marble sample. INTRODUCTION India is a major exporter of granite and marble stones. The major use of marbles and granites are constructing walls and floors. There are several machining processes that are applied before it is used as floors and walls. During this process, wastes are produced these wastes are used in various ways. These include use of powders for clay products (Segadães, Carvalho, & Acchar, 2005), as an additive in cement production (Aruntaş, Gürü, Dayi, & Tekin, 2010), to enhance the properties of brick ceramics (Saboya, Xavier, & Alexandre, 2007), in constructing bricks (Bilgin et al., 2012) and as an additive in concretes (Aliabdo, Abd Elmoaty, & Auda, 2014). Usually, the powder form of marble and granites are used as an additive in the above-mentioned applications. Powders of marble and granite are obtained through the grinding process. One such process of grinding is the ball milling process. In the ball milling process, a quantity of samples along with the charge quantity consisting of steel ball is subjected to a grinding process within a closed chamber as shown in Fig. 1. An even particle size can be obtained through sieving the material after subjecting it to grinding. The present study is planned to understand the particle size distribution in various sieves due to varying time and charge quantity in the experiment. Only time was varied to understand the amount of particle distribution in the case of granite and marble rock samples and a comparison is drawn. A statistical model was developed for marble rock specimen considering the data obtained by varying time and charge quantity in the ball mill experiment.

Jan 1, 2019

By John M. Marek

INTRODUCTION This paper is for the mining manager, generally meaning mine superintendent, chief engineer, and others who have control over the mine operation responsible for feeding the insatiable beast called the mill or processing plant. The author is not from mine management but from the field of technical mine engineering consulting. This fact illustrates the authors gross inadequacy to comment on this subject. On the other hand, the consulting profession allows visits to many mine operations, worldwide, supplying many different commodities. The common complaints and misunderstandings that have been heard worldwide will be shared within the following few paragraphs. In order to discuss optimization, one must first define it. There certainly will be many papers in the following sessions that claim to optimize something, or other, based on a technical definition of cost, efficiency, throughput or some other quantifiable basis. DEFINE OPTIMIZATION Actual optimization of an operation is not as easily achieved as most of us in the technical world would like. Borrowing terminology from the technical world, the boundary conditions and the optimization function are usually not well defined. The problems in many cases do not lend themselves to quantification. Typical management procedures are to establish goals or strategies that set the approach or general boundary conditions to the overall plant. Three simple cases are listed below as possible corporate strategies to optimization of a mine-process plant complex. 1) Maximized discounted cash flow 2) Minimized long term cost of product 3) Maximized resource utilization This list seems simple when presented in the above context, uncluttered by constraints such as market position, capital availability, or environmental limitations. Sometimes the best approach is a prioritized combination of the above items. Typically, the Board or CEO has established these strategic priorities. They may

Jan 1, 1991