Search Documents

By L. B. Pankratz

Heat contents were measured for Na2CaSi04 and Na2Ca2S02 between 298° and 1,300° K, for Na2Ca2Si309 between 298° and 1,500° K, and for Na4CaSi3O9 between 298° and 1,350° K. Copper-block drop calorimetry was employed. Reversible, first-order transitions were found for Na2CaSi04 and Na2Ca2Si309. The transition for Na2CaSi04 is at 830° K with a heat absorption of 160 cal/mole; that for Na2CagSi309 occurs at 750° K with a heat absorption of 1,550 cal/mole. Results for the other two silicates showed no irregularities. A table of heat content and entropy increments above 298.15° K and heat con-tent equations are included for use in thermodynamic calculations.

Jan 1, 1968

By T. Wulleman, M. Ansriou

Integrity testing is a primary quality control check on a product that is for the most part not accessible to visual examination. Their cost can be expensive when using direct methods of inspection (like coring a pile) or more economical when using indirect methods (e.g. acoustic testing). All indirect methods operate by “inference” which means that they do not directly measure the defect of integrity. Indirect methods measure the variation of physical values (temperature, impedance, speed, ect.) correlated to the integrity of the pile allowing the detection of integrity defects, although these methods do not allow for the characterization of the defect. 1. INTRODUCTION Cast-in-place piles are particularly prone to integrity defects. The reasons for this are multiple, including lack of high quality of contractor workmanship, experience and supervision necessary in construction, variable soil and groundwater conditions on site, etc. Furthermore, visual inspection of the finalized pile is usually impossible. Therefore, special care has to be taken both during the execution process and during the subsequent quality control campaign to detect any defects of executed piles. Today, a lot of methods do exist to assess pile integrity. It is thus essential to understand the mechanism governing those devices to both make an engineering choice of the pile integrity testing method and to interpret correctly the provided results. 2. QUALITY IN PILE FOUNDATIONS 2.1 Pile anomalies A pile having an anomaly is a pile which has a different behavior from what is normally expected. The presence of a pile anomaly does not necessarily imply that a pile cannot be used for its intended purpose (Gordon & Chapman 2004). An anomaly can be considered as a defect, or a “performance” depending on the ability of the pile to fulfil the following three criteria (3C): C1 - Meet the Service Limit State (SLS) requirement and support the proposed working load without settling more than admissible by the superstructure ; C2 - Meet the Ultimate Limit State (ULS) requirement and carry a specified load with an adequate factor of safety against failure ; C3 - Remain durable throughout the design life of the structure such that the pile is not affected by time dependent activities (chemical attack, corrosion of steel reinforcement, ect.), which would jeopardize its ability to maintain its compliance with the first two criteria.

Jan 1, 2019

By A. J. C. Paterson

High density slurry and paste tailings systems offer significant environmental benefits primarily related to reduced water consumption. However, these potential advantages need to be evaluated on a project-by-project basis. The successful design of a thickened or paste tailings system requires that the system is designed to accommodate the effect of the high density slurry on pumps, pipelines and the overall system operation. The transport system must be designed as an integrated unit and the interaction of all the components need to be considered. The transport system includes the slurry preparation plant, the pump station and the pipeline. This paper assesses the impact of increasing the slurry density in a platinum tailings system from conventional densities to thickened and paste tailings densities. As slurry density and rheology increase, there is a sharp increase in energy consumption for the additional water savings and this additional cost needs to be considered. A case study shows that there is a considerable benefit in increasing densities to the point at which tailings can be still be deposited in the standard manner. For existing systems, increasing density can result in an increased capacity at a marginal power cost, provided that the slurry is not too viscous. For a new system, a smaller pump and pipeline can result in lower capital costs and a marginally higher energy cost, if the optimum density is selected. Keywords: tailings, paste, pumping, slurry

Jan 1, 2004

By C. M. G. Wortley

One of the major deliverables of the AMIRA P754 Project, which was sponsored by several major mining companies, was a code of practice and guidelines for metal accounting for the mining and metallurgical industry. These had the objective of improving the auditability and transparency of metal accounting from mine to product, thus assisting in good corporate governance. The overriding objective of mass measurement for metal accounting is to establish the mass of the particular material or component present at a specific time, or the mass flow of that component over a defined time period, to a defined accuracy suitable for metal balancing. As such, it is the first measurement in the chain that includes sampling, sample preparation and analysis, each of which introduces its own errors. Materials often contain moisture, the proportion of which must also be established in order to obtain the dry mass. They may also have to be measured as a volume or mass/mass flow of slurry, or in stockpiles or storage areas, in which case the relative density must be measured. Both the density and moisture measurement often introduce significant error. Whereas a great deal of effort has been directed at sampling, sample preparation and analysis to improve accuracy and establish the error, the same can seldom be said for the mass determination, including the moisture and density measurements. The possible major causes of error are highlighted and methods of reducing them discussed. Mass measurement can be classified into those measurements necessary for custody transfer and primary accounting of the input and output streams to a plant or operation, and measurements required for secondary accounting, or management control. The latter include intra company transfers and plant area performance, and those required for plant control only. This paper is concerned only with primary accounting measurements. The code and best practice state that the equipment should be certified (as sized) as is required for custody transfer. The most accurate and precise of the various possible methods is the static measurement of mass on a weighbridge, platform scale or a weigh bin. If static measurement is not possible, which is often the case for ore fed to a plant, possible alternatives are electromechanical conveyor belt weighers or in-motion weighing of rail trucks. In all cases the material must be adequately sampled to enable a representative moisture content to be determined to calculate the dry mass. Where material is flowing inside conduits, only certain types of the multiplicity of flow meters available may be used and, in the case of slurries, very few flow meters are suitable. As most flow meters measure volume or velocity, the density of the material must also be measured. The basic requirements in order to achieve satisfactory results for the mass, of the component of interest, are listed, as well as common problems and pitfalls encountered in practice. The measurement of the mass of stockpiles and in-plant stocks, often required for metal accounting, is often the largest source of error in metal balances. The reasons for this and methods for reducing and managing the effect are discussed.

Jan 1, 2009

By James F. Kemp

The iron ores of southeastern Cuba present a subject of exceptional geological interest. Their relations to the inclosing rocks are varied and in some cases unusual. The problem of their geological origin is not a simple one and for this reason has occasioned some divergence of views among previous observers. Profiting, however, by these earlier studies and by more detailed field and laboratory observations as well as by the experience of added years of mining, much more satisfactory descriptions and interpretations can now be prepared. Previous Work In 1884, interest in the southeastern coast of Cuba became active among the consumers of iron ore along the Atlantic seaboard of the United States. Active development was undertaken by the Juragua Iron Co., Ltd., a corporation affiliated with the Bethlehem Steel Co., and the Pennsylvania Steel Co. The property of the Juragua company, which is situated about 15 miles east of Santiago, was studied in June and July, 1884, by Dr. James P. Kimball, at the time Professor of Economic Geology in Lehigh University and one of the best known of American mining geologists. Dr. Kimball published on his return two papers, the first important descriptions which we have of the local geology.1 It is

Jan 1, 1916

By David S. Graham, Joseph D. Bailey, Paul J. Axtell, Michael K. Muchard

"Two instrumented test piles were simultaneously subjected to a static lateral load test by jacking the piles apart. One of the piles was loaded in axial compression via kentledge during the lateral load test. Both piles were constructed in an identical manner. These piles were constructed and tested as part of a construction-phase load test program for a floodwall improvement project along the Missouri River in Kansas City, Kansas. Details of the subsurface conditions, drilled pile construction, instrumentation, and load testing procedures are described. Data collected during testing of the piles are presented and compared. Potential effects of the axial compressive load related to observed differences in pile lateral response are discussed.INTRODUCTIONTwo instrumented test piles were simultaneously subjected to a static lateral load with one of the piles also subject to a combined axial load during testing. The load test program was part of a floodwall improvement project in Kansas City, Kansas. Known as the BPU floodwall, the floodwall runs along the south bank of the Missouri River at a Kansas City Board of Public Utilities power generation and water treatment facility. The project location is shown in Fig. 1.Drilled, 2-ft (610-mm) diameter piles were designated by the designer, the U.S. Army Corps of Engineers (COE), as the foundation type for supporting extended floodwall footings. The drilled piles are fully cased, cast-in-place concrete, reinforced with a steel 12x74 (310x110) H-pile. In order to test soil lateral response and pile structural response under combined loading, the COE required that both a lateral test and combined lateral and axial test pile be constructed and tested. In order to most efficiently test both piles and to allow for simpler comparison, the two piles were simultaneously laterally loaded by jacking the piles apart, applying a maximum lateral load of 195 kips (867 kN). A constant axial load was applied to the combined test pile by kentledge prior to lateral loading and was maintained for the duration of the lateral load test. The total weight of the kentledge was 61.5 kips (274 kN). Fig. 2 shows the test setup."

Jan 1, 2017

By S. N. Kalyakin, D. S. Flett, M. A. Mulagaleeva, N. V. Gudkova, S. S. Serdyuk, V. I. Kuzmin, Institute of Chemistry and Chemical Technology SB RAS, O. A. Logutenko, V. N. Kuzmina, V. G. Lomayev

"The Chuktukon niobium-rare earth elements ore deposit is located in Siberia (Russia). Weathered carbonatite crusts are the basis of the ore deposit. The deposit itself is 3.5 km in length, about 800 to 1400 m in width and up to 200–300 m in thickness. The ores are composed of iron-manganese oxides (hydrogoethite, hematite, psilomelane, pyrolusite) and contain 3–7% of rare-earth phosphates (florencite, monazite) and 0.5–1% of niobium oxide (pyrochlore). The ore is completely finely dispersed and consists of oxide particles formed of compact, dense aggregates which makes ore dressing as well as leaching of the rare and radioactive elements very difficult. Several options for processing of these ores have been considered: 1) reduction of the iron oxides to magnetite followed by beneficiation with magnetic separation to produce a rare metal concentrate; 2) processing of the rare earth elements (REE) containing minerals by direct alkaline-acid treatment; 3) processing of the ores using nitric acid leaching in an autoclave.INTRODUCTIONThe Chuktukon niobium-rare earth metal ore deposit is located in Siberia, in the Krasnoyarsk region, 110 km from the Boguchan hydroelectric power station which has recently been commissioned. This mineral raw materials is capable of providing impetus for the modernization of the Russian rare metal industry because of its qualitative and quantitative characteristics. The deposit is located in a region of promising industrial development and is a part of the territoriy where the Russian Federation’s Program “Complex Development of the Lower Angara Region” is currenly being realized. The main program directions are creation and development of industrial activities in sectors such as power, metallurgy, oil and gas, gold, rare-metals, and timber. The program will aid the development of the niobium and rare-metal resources of the Lower Angara and neighbouring regions as well as increase the national production of REE and therefore import substitution (Lapin, 1997; Lomaev & Kuzmin, 2003; Lomaev & Serdyuk, 2011; Serdyuk, Lomaev, & Kontorovich, 2000)."

Jan 1, 2016

By L. Andrews

Mineralogy, traditionally associated with concentrator studies, is being increasingly applied to problems in pyrometallurgy. Such investigations commonly make use of a number of techniques, and the results are combined for a meaningful interpretation, which can lead to a successful solution for the problem. Mineralogical techniques are described for various pyrometallurgical operations. Examples are given of studies and investigations involving mineralogy in chemical-looping combustion, feed monitoring to platinum-smelting furnaces, and losses to slag in base metal and platinum smelting.

Jan 1, 2011

By J. P. Sheehan, W. R. Hibbard, M. Baeyertz

This paper deals with molybdenum modifications of 5140 steel that have the same hardenability but a better tolerance for phosphorus than the AISI-SAE 5140 grade. Lack of toughness in steels with higher than normal phosphorus contents is well known to metallurgists. This problem is troublesome even within normal phosphorus ranges, if the heat treatment or the design of the part or the service is critical. Under such unfavorable conditions and also in the case of phosphorus contents toward the upper side of the commercial range, the use of molybdenum to replace a part of the chromium in 5140 steel provides a factor of safety. The toughness of steel is variously exhibited in different mechanical tests; broadly the term is applied to the capacity of the steel to deform prior to fracture. Defined in this way, toughness is considered to be an inherent quality that depends upon the composition and structure of the steel, and also upon its temperature during deformation and fracture in the test. In the present state of our knowledge, the type of mechanical test needs to be included in any discussion of toughness, because the revelation of this quality in steel depends on the stress state and rate of stressing imposed by the test. In comparing the toughness of one steel with another by laboratory testing, it has long been customary to use notched tests that impose severe constmint to deformation, and then to test over a range of temperatures to obtain the so-called transition. At temperatures above the transition, the steel fails after considerable deformation and absorption of energy. Below the transition, less energy is absorbed as the steel fails largely by cleavage. The transition range itself is characterized by a more or less abrupt change in energy absorption and type of fracture. The conventional V-notch Charpy impact test has been used exclusively in the work covered by this report. For the steels under study, rather sharp transitions are obtained with this test, at testing temperatures that are easily obtained in the laboratory. The position of the transition on the testing temperature scale provides a rather sensitive index of the toughness of the steel, when the steels under study are similar in character as they are in this work. Turning to the metallurgical reasons for the greater toughness of one steel as compared to another, the authors propose to limit the discussion to the small field under study. Only one structural state is considered, tempered martensite of a hardness of about 28 Rockwell C or 269 Brinell. The study deals first with the loss of toughness in AISI-SAE 5140 steel caused by increasing the phosphorus content from about 0.020 to 0.040 pct. A second part of the work deals with counteracting this loss in toughness by replacing a part of the chromium by molybdenum. A series of molybdenum modifications was studied, in each of which the chromium was reduced sufficiently to duplicate the hardenability of 5140 steel. Phosphorus affects the toughness of steel in two ways. An inherent lack of toughness of phosphorus-bearing ferrite as compared to low phosphorus ferrite has often been noted. Jolivet and Vidall have shown that phosphorus has the same effect in tempered martensite in chromium steels. The other well known effect of phosphorus is to make steel susceptible to temper embrittlement. Temper brittleness is a loss in toughness brought about by tempering steel within a limited temperature interval somewhat below the A1 temperature. In most of the standard AISI-SAE alloy steels, this temperature interval is approximately 850-1100°F. Either of these types of loss in toughness is easily followed by the shift in the transition temperature obtained with the notched-bar impact test. The data to be presented show the beneficial effect of substituting molybdenum for a part of the chromium in 5140 steel with either moderate (0.020 pct) or high (0.040 pct) phosphorus contents. Both the inherent lack of toughness of phosphorus-bearing steel and temper brittleness are counteracted by this use of molybdenum. The work of Jolivet and Vidal mentioned above shows the detrimental effect of phosphorus on the toughness of tempered martensite in the absence of temper embrittlement, as well as the temper brittleness caused by phosphorus. They used two steels, essentially 0.25 pct C-1.4 pct Cr, with 0.044 and 0.013 pct P, respectively. The nonembrittled state was obtained by quenching in oil from 1610°F, then tempering for one hour at 1200°F and quenching in water. In this state the transition temperature range of the low phosphorus steel in the notched-bar impact test was below that of the steel with 0.044 pct P. An additional treatment of 24 hr at 975°F (that is, in the embrittling range) caused both steels to lose toughness, but the high phosphorus steel showed the greater embrittlement. Recently Hollomon2 has published a comprehensive survey and bibliography of the literature on temper brittleness, to which the reader is re-

Jan 1, 1950

By C. E. Arnold

A BRIEF description of this installation was included in a recent paper by H. Kenyon Burch.1 The purpose of the present paper is to amplify Mr. Burch's description, as it is felt by the writer that the subject merits more than passing attention. In making a comparison between the common method of hoisting men in mine shafts, and elevator practice in high buildings, the former shows to great disadvantage both as regards safety measures and smoothness of operation. It is surprising that in view of the inducements offered, the step of applying the building equipment direct to the mine shaft has not been taken before, as in many respects the conditions of service are similar, and the objects to be attained are identical. Even without doing this, it is certain that safety to life and limb in the usual method of hoisting men underground can be greatly enhanced by the application to the mine hoist, of some of the features of the building elevator. In the case under consideration, the elevator cage runs in a vertical, concrete-lined shaft compartment 5 ft. 11 in. by 5 ft. 6 in. (1.8 by 1.68:m.) in section and 585 ft. (178 m.) deep, while the counterweight runs in the pipe and ladder compartment of a twin shaft 102 ft. (31 m.) distant. The section of the division of this compartment occupied by the counterweight measures 2 ft. 4 ¼ , in. by 3 ft. 10 ½ in. (0.72 by 1.18 m.), and the counterweight is made in the form of a small cage which. suffices to carry two men for the purpose of making inspections or repairs in the pipe and ladder way.

Jan 12, 1917

By B. S. Hickman

Using primarily quantitative single crystal X-ray techniques studies have been made of the precipitation of the metastable w phase in alloys of titanium with Mo, Mn, Fe, Cr, and Nb. It is shown that, in agreement with earlier work on the Ti-V system, the composition of the w phase during aging approaches a constant; the value varies from one system to another in a systematic manner with the electron concentmtion. Results relevant to the mechanism of w precipitation during quenching and during aging are presented and discussed. Results are presented to confirm that the w phase is coherent and the nzorphology of the Necipitates is described and discussed. PRECIPITATION of the metastable w phase in alloys of titanium is of interest because of its severe embrittling effect and also because of the enhancement of the superconducting properties which accompanies precipitation.1 The general features of w phase precipitation have been discussed by cuillan and by Bagaratskii et d3 The work described in this paper forms part of a general study of w phase precipitation which was undertaken to elucidate various unknown or controversial features of the process, namely: i) What is the mechanism of formation of the phase ii) How does its composition, morphology, volume fraction, and particle size vary with the type and content of the alloying element and with the heat treatment conditions? iii) What is the relation between the w phase and the equilibrium a phase? In a previous paper4 the results of a detailed study of w phase in Ti-V alloys were presented. It was shown that: U During aging the composition of the w phase approached a saturation value of 13.5 to 14.0 at. pct V. ii) w precipitated as cube shaped particles and once precipitation was complete, particle coarsening did not occur. iii) a phase formed initially by direct conversion of w-phase precipitates. In this paper similar measurements are reported on Ti-Mo alloys and some more limited data given on the Ti-Cr, Ti-Fe, Ti-Mn, and Ti-Nb systems. The results i.1 the six systems are then compared. It has been shown previously by electron microscopy that the w precipitates as ellipsoids in both the Ti-Nb system,&apos; and in i-o.&apos; Blackburn and williamsz3 have reported the precipitates in Ti-Fe, Ti-Cr, and Ti-Mn are cubic, i.e., similar to the Ti-V system.476 EXPERIMENTAL METHODS 1) Specimen Preparation. Samples of the compositions shown in Table I were prepared by arc melting. High purity electron beam zone refined titanium (Materials Research Corporation Grade I—total impurity content =250 ppm) was used; the other source materials are given in the table. A commercial Ti-8 wt pct Mn alloy was used for studies of this system. After homogenization the materials were rolled or cut into strip approximately 1/4 in. by 2 in.; the strip was then heated at temperatures of 1200" to 1300°C for several hours by passage of a direct current through the strip in an ultra high vacuum system (<10-torr) and then quenched by admitting high purity helium and switching off the current. This treatment resulted in crystals up to 2 in. by 2 in. by A in., almost all of which had a [100] direction nearly perpendicular to the plane of the strip. The crystals were cut from the strip by spark machining and their composition checked by lattice parameter measurements supported by chemical analysis. 2) X-Ray Diffraction Methods. Lattice parameter measurements were made using a modification of the single crystal spectrometer described by ond. In this technique the crystal angles for reflection on either side of a highly collimated primary beam are measured. Generally the 400 CuK, or the 400 CuKp reflections of the bcc lattice were used. In the as-quenched crystals a precision of 1 in 105 was obtained, but due to line broadening the parameters in aged materials could only be measured to 1 in lo4. This accuracy was, however, quite adequate for the purposes of these experiments and enabled the composition of the p phase to be obtained to 10.1 pct in all systems except Ti-Nb where the lattice parameter change with composition is very small. The precipitation and growth of the w phase was examined using a single crystal goniometer attached to a Phillips diffractometer. The relative intensities and line shapes of b-phase and w-phase reflections

Jan 1, 1970

By R. W. Hagemeyer

By way of background. it is important to keep in mind that the information presented in this paper relates specifically to synthetically produced precipitated calcium carbonate (PCC) fillers. Natural calcium carbonate fillers manufactured by grinding limestone, marble and chalk, though having similar chemical and physical analyses to PCCs, normally contribute somewhat different performance properties in paint, paper and polymer systems. Many factors have been cited and numerous theories have been proposed for the observed differences. Particle size parameters, surface chemistry and particle morphology are the items most frequently mentioned. A discussion of this subject is beyond the scope of this paper.

Jan 1, 1989

By S. Neogy, M. Gupta, D. Srivastava, V. Kain, S. Roychowdhury, R. C. Prasad, G. K. Dey

"Austenitic stainless steels are an important material of construction for Boiling Water Reactors (BWR). These stainless steels are amenable to strengthening by strain hardening. Various deformation modes at different test temperatures and strain become active. In the present investigation type 304LN stainless steel was used in the annealed and strain hardened condition. Thin foils were prepared from gauge section for transmission electron microscope (TEM) investigation after tensile testing at room temperature and at 288°C. TEM investigation reveals that twinning is the major mode of deformation for the tests done at room temperature while dislocation cross-slip is the major mode of deformation at higher temperature. Stacking faults were also observed to a limited extent. The extent of twinning was much higher for the tests done using the rolled material. The formation of martensite in the stainless steel due to straining was investigated by the analysis of selected area diffraction patterns.IntroductionAustenitic stainless steels (type 300 series) are an important material of construction in Boiling Water Reactors (BWR). These stainless steels cannot be heat treated but can be strengthened by cold working [1]. Nitrogen alloying of these stainless steels result in high strain hardening rates and higher strength without any loss in toughness [1]. Stress Corrosion Cracking (SCC) in BWR of these types of stainless steels have been attributed to surface strain hardening and strain hardening ofregions adjacent to constrained weldment [2].The test temperature [3, 4], prestrain [5] and nitrogen level [5] has been reported to affect the deformation mechanism during tensile testing. Byun et al. [3] have reported the formation of martensite, dislocations, stacking faults and twinning during tensile deformation, the extent of each depending on the test temperature. Strain localisation has been reported to occur during tensile deformation in irradiated stainless steels [ 6]. The behaviour of rolled material during tensile testing is similar to that of irradiated material to a large extent [3]. Austenitic stainless steels are low stacking fault energy (SFE) materials in which various types of microstructures have been reported to form during tensile deformation and the strain is also highly heterogeneous in nature in these stainless steels which aides SCC in BWR environment to a large extent [7]. During cold working of austenitic stainless steels second order twinning has also been reported [8]. Knowledge about the deformation mechanisms operative in the strain hardened austenitic stainless steels during tensile testing at different temperatures is essential to understand the material deformation behavior and the present study aims at enhancing the existing understanding."

Jan 1, 2011

By Richard F. Sliwoski

The Virginia State Capitol was designed by Thomas Jefferson and constructed in 1785. The Capitol is of great historic and architectural significance to not only the Commonwealth of Virginia but to the nation. It is the oldest operating Capitol in the U.S. and required a total restoration/renovation as well as an expansion to continue to remain functional. Site conditions dictated that the expansion (a new visitor center) be placed underground on the south side of the Capitol building, requiring a 40-foot deep excavation approximately 5 feet from the Building. Because of its historic significance, every measure had to be taken to ensure the safety and function of the Capitol during construction. The construction techniques that were used to make the deep excavation and protect the historic Capitol included a tied back concrete slurry wall, jet grouting, compensation grouting, and instrumentation monitoring. This paper describes the history of the Capitol building, the techniques that were employed for construction of the deep excavation, results of the latest movement monitoring, and factors contributing to meeting the restrictive movement goals.

Jan 1, 2006

By Rami Abousleiman, Gabriel Walton, Sankhaneel Sinha

"Although conventional coal mine designs are conservative regarding pillar strength, local failures such as roof-falls and pillar bursts still affect mine safety and operations. Previous studies have identified that discontinuous, layered roof materials have some self-supporting capacity. This research is a preliminary step towards understanding these mechanics in coal-measure rocks. Although others have considered broad conceptual models and simplified analogs for mine roof behavior, this study presents a unique numerical model that more completely represents in-situ roof conditions. The discrete element method (DEM) is utilized to conduct a parametric analysis considering a range of in-situ stress ratios, material properties, and joint networks to determine the parameters controlling the stability of single-entries modeled in two-dimensions. Model results are compared to empirical observations of roof-support effectiveness (ARBS) in the context of the coal mine roof rating (CMRR) system. Results such as immediate roof displacement, overall stability, and statistical relationships between model parameters and outcomes are presented herein. Potential practical applications of this line of research include: (1) roof-support optimization for a range of coal-measure rocks, (2) establishment of a relationship between roof stability and pillar stress, and (3) determination of which parameters are most critical to roof stability and therefore require concentrated evaluation.INTRODUCTIONRecent studies on pillar design have suggested that the assumptions utilized in traditional methods such as tributary area theory (TAT) (i.e. overburden has no self-supporting capacity, infinite pillar array, and CHILE material properties) are invalid in many geo-mining conditions (Esterhuizen, Mark, and Murphy, 2010; Frith and Reed, 2017). Although TAT is conservative with respect to pillar loading, and mine fatalities have steadily decreased since 1990, roof-falls and pillar bursts still occur and injure hundreds of miners per year (Mark, Pappas, and Barczak, 2011). Even though large-scale global mine failure has not occurred in a US coal mine since 2007, the mechanics of global and local stability as governed by the relationship between geologic parameters, mine geometry, and engineering design are still not well-constrained.Numerical methods are a highly effective tool that can be used to gain further insight into these relationships. When using such an approach, calibration to existing empirical relationships is imperative to ensure that numerical model results are realistic. In this study, we utilize the discrete element method (DEM) approach in Itasca’s Universal Distinct Element Code (UDEC v. 6.0) (Itasca, 2010).DEM accounts for explicit separation and contact of individual deformable blocks (Jing, 2003) and captures how discontinuities can affect system behavior. Discontinuous and anisotropic rockmass properties are typical features in coal-measure rock which contain various horizontal (bedding) and sub-vertical (joints) fractures depending on their depositional environment, diagenesis, and historic and current stress states."

Jan 1, 2019

By O. J. C. Runnalls

"Canada became the world&apos;s largest uranium producer in 1984. That leadership position is likely to be maintained for many years into the future because of a firm production base, many undeveloped known deposits with commercial promise, and a large geologicalpotential for new discoveries.There are some uncertainties on the horizon, principally because of restrictive actions in process within the U.S.A., which are aimed at preserving a deteriorating domestic uranium industry. Should such actions result in import restrictions, for example, there would be a negative effect on foreign producers at least in the short term. Canada may avoid such difficulties under a tentative U.S.-Canada free-trade agreement where restrictions on the import of Canadian uranium into the United States would be eliminated. Over the longer term, demand for Canada&apos;s uranium resources will grow because of the foreseen growth in the world&apos;s installed nuclear power capacity. IntroductionSince the phenomenon of nuclear fission was discovered in 1938, the utilization of uranium has grown substantially. Initially, the principal use for uranium was in the production of nuclear weapons. However, once civilian nuclear power reactors began to be built in the 1950s, an increasing fraction of uranium output was directed to the production of fuel elements for use in electricity generating stations.The cumulative uranium production by those countries in the World Outside Centrally-Planned-Economies Areas, WOCA, during the period 1938 to 1985 exceeded 800 000 tonnes of uranium. Some 60% of that was mined in the United States and Canada, as indicated in Figure 1. In 1986, nearly 80% of WOCA output came from five countries, Canada, United States, South Africa, Australia, and Namibia, as indicated in Table 1 and illustrated in Figure 2.During the past decade the world annual consumption of nuclear energy has more than tripled (Fig. 3). As of December 31, 1986, the world total of nuclear power reactors had reached 394 with a total net capacity of 270 GWe. The thermal output from nuclear power plants in 1985 exceeded 60% of the energy contained in all of the oil produced that year in the Middle East. Thus, nuclear power has already become an important component in the world energy supply picture."

Jan 1, 1988

By Stanley Dempsey

INTRODUCTION The mining industry has been under- going a significant restructuring for the past several years. Some firms have been liquidated. Some have been merged with other firms. A number of mining divisions of larger firms have been spun off, in some cases in leveraged buyouts by management. Recently, there have been a number of spin outs of gold subsidiaries. There are also a number of start-up situations where new firms are emerging as significant gold producers through mine development or acquisition. This restructuring has created an attractive market for specialized mining finance firms, and a number of firms have recently entered that field in the United States. These firms provide financial advisory and valuation services to mining firms and project developers, and access to venture capital. In some cases, they invest for clients or for their own account. I have been asked to describe how our firm works, and what kind of information we expect to receive when mine developers seek our assistance in financing a project. HOW WE OPERATE Denver Mining Finance works for both mine developers and investors. We also provide expert advice on mining issues to governments and to firms who are in litigation over mining issues. A lot of our work involves valuing mineral interests for various purposes. Our principal expertise is in the technical, commercial, and financial area. We help put mining deals into shape commercially so that they can be financed, and we help investors get into mining deals that are commercially sound. We work on projects, but we also advise mining firms on the structure of their business and how to make the most out of one or several mines that they might own. In addition to our work for clients, we are also prepared to invest in mining projects for our own account, and to recommend gold properties for acquisition by our parent company, Royal Gold, Inc. We are, to some extent, a venture capital firm, in that we sometimes work with projects that are not "bankablerV1 and are prepared to invest in attractive early-stage situations in mining. However, I want to emphasize that our principal focus is on development of commercially attractive mining projects that can be brought into production in the best possible financial terms. If we can make a project qualify for a project loan from a commercial bank, we will not advise the developer to use high cost venture capital. For the purpose of this paper, I will focus primarily upon our functions with respect to development of precious metal projects. In a typical case, a firm with an advanced-staged project approaches us for help with financing the final feasibility study, and construction and operation of a mine. In some cases, the developer has already developed a financing plan and wants only our access to investors. If we agree that the project is sound and that the financing scheme will be attractive to investors, we will help the developer reach investors on a commission basis. In such cases, we are particularly insistent that the financing plan and our participation meet all regulatory requirements, particularly compliance with state and federal securities laws. In most cases, however, the developer asks us for advise both on how to structure the financing, and how it can be implemented. Here we work for fees based on hourly rates for advisory work,

Jan 1, 1987

By Steven W. Hunt, Isabelle Lamb, Steven B. Fradkin

Groundwater control is generally an important consideration and significant source of risk during most tunneling projects. Proper baselining of groundwater conditions requires: 1) a thorough understanding of the geological environment; 2) a focused site investigation; 3) identification of construction and adjacent property damage risks associated with inflows and short and long term piezometric level changes; and 4) consideration of contractual issues including restrictions on means and methods and pay items for associated work. This paper provides an overview of groundwater baselining issues and risks based on selected design studies and construction case histories.

Jan 1, 2005

By L. M. Abrantes, A. P. Paiva

"A brief review of some innovative methods for the direct recovery of metals from loaded organic phases is presented; emphasis is given to electroreductive stripping and cementation, which are described and illustrated by examples: of current research. The recovery of silver using a two-phase electrolysis - by direct application of an electrical potential to a mixture of a metal loaded organic phase· containing Cyanex 471X, obtained by solvent extraction, and a stabilized sodium thiosulfate solution - is more extensively discussed. The overall efficiencies are analyzed and compared with data obtained by conventional stripping procedures. Some preliminary results achieved for the recovery of the precious metal using galvanic stripping, applied directly to similar organic solutions and involving zinc and iron powders as reducing agents, are also evaluated.Introductory ReviewThe application of hydrometallurgical methods to the recovery of metal values from ores and concentrates has been receiving a growing interest, either from researchers or from the mining industry [1].For the concentration / purification of the relatively low concentrated metallic solutions resulting from the leaching of those raw materials, solvent extraction (SX) is a well established technique [2]; the loaded organic solvent is then conventionally contacted with a suitable aqueous solution, the metal in its final form being usually recovered from this solution by electrowinning.As an efficient and / or selective stripping is sometimes difficult to achieve, depending on the specific characteristics of the system under consideration, some alternative procedures have been analyzed in order to overcome this problem. One of the chosen routes, mainly developed by Hirai and Komasawa, is to promote the reduction of the desired metal species in the organic phase, in such a way that the stripping stage becomes feasible; for the selective stripping of vanadium from a solvent containing a mixture of vanadium and molybdenum, the authors successfully used reductive [3], electro-reductive [4,5] and photo-reductive [6] techniques. The two latter methodologies have also been applied to the recovery of europium from a solvent containing europium, samarium and gadolinium [7,8].However, further processing is necessary to recover the metal in its solid state; therefore, methods causing the direct reduction of the metal species in the organic phase to their fmal metallic form would be of interest, as an intermediate step would be avoided"

Jan 1, 1997

By Stanley W. Ivosevic, Mark E. Emerson

Introduction Metals exploration activity is moderately intense in the US despite the 1981-82 recession in the mining industry. Although exploration expenditures are significantly less than the 1981 peak, quality and goal orientation of current exploration are high. Major foreign and domestic mining companies as well as nonmetal companies had been attracted to invest in minerals in the US. Its capital markets, political stability, and open-door policy are attractive for hard mineral explo¬ration, particularly in the West. The approach was to either acquire fully or partially developed ore bodies through merger and acquisition, or to fund large scale exploration programs in search of bulk-tonnage deposits. The acquisition avenue has not proved the panacea envisioned for overcoming lack of substantive mineral development. Nor has the decentralized approach to exploration that was adopted proven cost-effective. The emphasis on gold, to the exclusion of all other commodities, raises questions regarding the direction of exploration in the US for the rest of the 1980s. Overview More than 300 companies are active in metals exploration in the US. These range from established, well-known domestic and foreign corporations to hurriedly incorporated, unknown companies financed by having promoted mineral prospects or occurrences of questionable quality. Junior companies tend to be oriented toward property entrepreneurship, rather than the development of minerals resources. These companies have helped maintain mineral lands from prospect to production by holding blocks of property intact during periods of exploration inactivity. This was done through promotional efforts, even though few properties that attracted major venturers proved to have real merit. Exploration objectives of senior and junior exploration companies currently embrace only a few commodities. Arranged in approximate descending order of priority, these are: precious metals; base metals in monometallic or polymetallic deposits; strategic metals, such as tungsten, tantalum, and tin; unconventional commodities, such as diamonds; ferrous metals; and commodities such as beryl, zeolites, and barite. Prospectors are important in searching for these targets. In the US, where they have been financed by major and junior companies, prospectors have proven a useful and low-cost means of locating gold prospects (e.g. the Alligator Ridge property in Nevada). The tenacity and persistence of independent prospectors have been factors in discovering properties rejected or overlooked by professional geologists (e.g. Lornex mine in British Columbia). This has been realized by the provincial government that grubstakes bona fide prospectors. Exploration interest in commodities has always been cyclic with price. Gold is one of the few metals that has experienced a price increase of such magnitude to warrant attention. The potential for realizing adequate operating margins for the Nevada open-pit "no-see-um" gold deposits is great. The present declining gold price, however, may indicate that this emphasis on gold, to the exclusion of other commodities, is shortsighted. Mining companies have been the last to react to price increases, opening new mines based on unrealistic market expectations. A scenario could develop where plummeting gold prices bring recession to the gold industry, as lately occurred in uranium, molybdenum, and copper. US Exploration Climate The US is attractive for exploration due to its strong mineral po-

Jan 4, 1984