Search Documents

By Stephen Buttling, Zhong Rui

"A single unit gas fired power station was being built on the edge of the Gulf of Thailand in 2001. The soil conditions consisted of very soft to soft Holocene Marine Clay, and the site was part of a coast line which had been subsiding below high water mark for some time. In order to provide access around the power station a road system in a figure-of-eight formation was required, and this also needed to be above the design flood level, allowing for future settlement. A ground improvement scheme was proposed and constructed, which consisted of two spacings of prefabricated vertical drains (PVD) over two depth ranges, vacuum consolidation and pre-loading, and rigid inclusions.During the construction phase, the vacuum consolidation was applied for 202 to 221 days in different zones, and monitoring allowed a prediction that the future settlement, including secondary consolidation over a period of 25 years, would be within the range of 175 to 355 mm, which met the contract requirement of less than 400 mm.The power plant was completed and became operational in 2003. Monitoring of the road levels continued, as did the settlement, and in early 2010 the total settlement since the end of vacuum consolidation had reached about 800 mm. The monitoring data both during the ground treatment and for the following 7 years is presented and analysed. This is supported by numerical analysis using 3D finite element methods which shows good agreement with the measured data, and allows a preliminary explanation as to why the predictions were so far out.BACKGROUNDAfter a period of bidding and negotiation, the Eastern Power and Electric Co Ltd (EPEC), an Independent Power Producer, entered into an agreement with the Electricity Generating Authority of Thailand (EGAT) in November 1997 to sell them power. In 1999 an Engineering, Procurement and Construction (EPC) contract and an Operation and Maintenance contract were signed with a supplier to provide a gas-fired (with oil as a back-up fuel) 350 MW combined cycle power plant in Bang Bo, Samut Prakarn Province, east of Bangkok. The site of the plant at Bang Bo is located immediately to the east of the Samut Prakarn Wastewater Treatment Plant, adjacent to the Gulf of Thailand (see Figure 1) in an area of very soft to soft marine clay (Bangkok clay) having low shear strength and potential for excessive settlement. The site layout comprises the main Power Plant components of generating block, cooling towers, fuel unloading area and storage tanks, switchyard and administration block, separated by access roads."

Jan 1, 1900

By Noakes M. J

Research and development into alternate gold and precious metals adsorbents has resulted in the development of a new technology named the AUROSAVE adsorption process (ARGOSAVE'" for high silver con- tent ores). Adsorbents called VITROKELE'" can be tailored for either Gold I (cyanide leach) or Gold III (halide leach) applications. VITROKELE consists of a chemically synthetic adsorbent carried on an inert substrate, often a polystyrene bead. It is suitable for both in- pulp and in-solution use. VITROKELE adsorbent offers certain advan- tages over both carbon and ion exchange resin adsorbents. This paper describes testwork on Australian ores and commercial solu- tions obtained from operating Australian plants demonstrating the kinetic loading characteristics, elution methods and other operating parameters of VITROKELE adsorbent in the cyanide system. Brief reference is made to VITROKELE in the Gold III system.

Jan 1, 1988

Jan 1, 1925

WMC Limited, owner/operator of Olympic Dam, the worldÆs largest underground uranium mine and the fourth largest underground copper mine has now completed an expansion that has been classed as a benchmark in the mining industry. To achieve a production increase from 3.4 to 9.25 Mtpa from an underground mining operation in two years was a major challenge, it was essential to review the overall materials handling system from æthe face to the stockpileÆ. The challenge was two-fold:How to deliver 30 000 tonne of ore per day to the processing plant, from a single underground mine? To provide the processing plant with a consistent metallurgical feed. This paper traces the transformation from the old to the new materials handling system at Olympic Dam.

Jan 1, 2000

By Michael S. Wieland

The work-principle from thermodynamics was used to formulate a model for predicting toxic fumes from mining explosives in underground chamber tests, where rapid turbulent combustion within the surrounding air noticeably changes the resulting concentrations. Two model constants were required to help characterize the reaction zone undergoing rapid chemical transformations in conjunction with heat transfer and work output: a stoichiometry mixing fraction and a reaction-quenching temperature. Rudimentary theory with an unsteady uniform concentration gradient was taken to characterize the combustion zone, yielding 75% for the mixing fraction. Four quenching temperature trends were resolved and compared to test results of ammonium nitrate compositions with different fuel-oil percentages (ANFO). The quenching temperature 2345 K was the optimum choice for fitting the two major components of fume toxicity: carbon monoxide (CO) and total nitrogen oxides (NOx). The resulting two-constant model was used to generate comparisons for test results of ANFO compositions with additives. Though respectable fits were usually found, charge formulations which reacted weakly could not be resolved numerically. The work-principle model yields toxic concentrations for a range of charge formulations, making it a useful tool for investigating the potential hazard of released fumes and reducing the risk of unwanted incidents. Keywords: Toxicity; Fumes; Explosives

By Norman Lecuyer, Jacque Nantel

"The Chadbourne Project, located within the limits of the town of Noranda, Quebec, will make use of backfill materials to fill the voids left by the mining of stopes and pillars. A series of tests were conducted on different mixtures of slag and pyrrhotite tailings materials to evaluate their properties. The tests are described and some pertinent results are given in the paper.IntroductionThe Chadbourne Project is located in the centre of the Town of Noranda, Quebec, with houses as close as 120 m from the blasting operations. The ore is mined using the vertical crater retreat method. The voids left by mining activities will be filled. A program of pillar recovery will follow.Considering the proximity of houses and the need to recover pillars, the backfill program must be carefully laid out. No subsidence can be tolerated on surface.With these objectives in mind, a test program was undertaken by Nantar Engineering Limited and Queen's University to evaluate the possible ba ckfilling alternatives available to Chadbourne. One of the possibilities retained was the use of a backfill composed of broken slag material from the Horne Smelter and pyrrhotite tailings deposited on the Horne's pond a number of years previously.The back fill used at the Horne Mine until the mine closed in 1975 was composed of a mixture of 97% granulated slag and 3% pyrrhotite tailings. The tests leading to its use underground at the Horne Mine were described by Patton in 1952. The structural properties of the Horne backfill were ""intuitively"" known; it was agreed by all at the Horne Mine that the backfill was behaving remarkably well. Some were labeling it ""the best backfilling material in the world"". Its strength was said to be that of a weak concrete. All of the preceding indicate that the Horne backfill had never had its structural and other properties determined in the laboratory."

Jan 1, 1983

By D. Tao

Coal is a major source of energy in the U.S. and more than 51% of the electricity used in the country is generated from coal. Coal cleaning prior to combustion is necessary and often accomplished using wet physical processes at coal preparation plants to remove impurities such as ash, sulfur, mercury. However, the resultant clean coal product still contains a significant amount of impurity due to the fact that impurities are not well liberated from coal particles ranging from several millimeters to inches in size at which wet cleaning processes take place. A cleaner coal product can be obtained if a cost-effective dry process is developed to further clean pulverized and thus better liberated fine coal at the power plants prior to its combustion. The benefit of such a process is a significant reduction in the cost of expensive post-combustion chemical cleaning processes such as flue gas scrubbing employed to meet the stringent environmental air quality regulations. In this study, a novel rotary triboelectrostatic separator (RTS) was investigated for its application to dry cleaning of fine coal samples acquired from the power plants in the state of Illinois. The pulverized fine coal contains well liberated ash and pyrite minerals and is an ideal feed to the triboelectrostatic separator for further cleaning without the use of water or any chemical reagents. The proprietary rotary triboelectrostatic separator (RTS) is characterized by an innovative high efficiency rotary charger, charger electrification, laminar air flow, and specially designed electrodes. Compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator offers significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range, etc. Testing with several fine coal samples has demonstrated that this technology can significantly reduce ash content with a process efficiency similar to or better than froth flotation. Important process parameters such as charger rotation speed, injection and co-flow rate, feed rate were investigated for their effects on separation performance.

Jan 1, 2010

By Dennis Ofiara, Michael Lewis

An experimental 1.75 meter Shaft Boring Machine was designed and manufactured by The Robbins Company. The drill was used by contractor Drillcon Raise AB to drill test shafts at an SKB underground test facility. SKB is the Swedish authority responsible for safe management of nuclear waste materials. This “SBM1.8” Shaft Boring Machine was used to drill shallow test shafts ingranitic rock at SKB’s Aspo underground laboratory. The drill used a unique vacuum mucking system. The bored shafts were held to very strict tolerances for bore diameter, straightness, and verticality. This drill was launched and operated from a mobile launcher. Headroom and working space were limited. The SBM1.8 drill produced acceptable test holes. SKB will carry out several studies to determine the suitability of this geology, and of this technique, for safe nuclear disposal. In addition to future use at SKB, many applications are foreseen, particularly in the civil construction industry.

Jan 1, 2005

By J-P Franzidis

A technique for determining the recovery of attached particles across the froth phase in flotation that relies on measuring the rate at which bubble-particle aggregates enter the froth is used to investigate the selectivity of attached particles across the froth phase. Combining these measurements with those of other techniques for determining the froth recovery of attached particles provides an insight into the different subprocesses of particle rejection in the froth phase. The results of experiments conducted in a 3 m3 Outokumpu tank cell show that the detachment of particles from aggregates in the froth phase occurs largely at the pulp-froth interface. In particular it is shown that the pulp-froth interface selectively detaches particles from aggregates according to their physical attributes.

Jan 1, 2005

By Tom McDonald, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to soft material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessary as vertical presplit drilling produced wall failures.

Jan 1, 1997

By T. G. Madgwick, W. Calder

Production of petroleum increased again during 1929, thus maintaining the steady growth inaugurated by the bringing in of Royalite No. 4 in Turner Valley, Alberta, towards the end of 1924, prior to which a decline over a number of years had been experienced. The growth has been confined to the Province of Alberta, the older production in New Brunswick and Ontario showing declines, although in the latter case considerable activity in the search for new gas structures was maintained and during the last six months two wells were brought in, one at Howard in the Trenton at a depth of 1250 ft., giving 5,500,000 cu. ft., and the other at Tilbury in the Guelph or Salina at 750 ft. giving 9,000,000 cubic feet. As has been the case during the past five years, interest in the search for structure and in the following up and development of areas already recognized has centered in Alberta and adjacent portions of Saskatchewan. This was due in the first instance to the striking of wet gas in the Palaeozoic limestone (Madison) of Turner Valley, some 30 miles south of Calgary, in Royalite No. 4 in October, 1924. The bringing in of other wells of similar importance late in 1928 and in the spring of 1929 which extended the productive area 3 miles southwards led to greatly enhanced drilling activity throughout the structure and adjacent areas and in other parts of Alberta. As a result good strikes of heavy crude oil have been recorded during the year at Ribstone, Oyen, Skiff and Coutts, in each case at moderate depths and in sufficient quanitity to justify prolonged testing. The prospects of a satisfactory production of this grade of oil are very encouraging. Actual oil production in the west is still confined to the Province of Alberta and for all grades of oil totaled 997,359 bbl., which compared with previous years shows a gratifying increase. To this increase the naphtha obtained from the wet gas of Turner Valley has proved the principal contributant, heavy crude also showing an improvement, while the light crude, the product of the Cretaceo-Jurassic sands overlying the Paleozoic of Turner Valley, remains unchanged. This is largely owing to operators casing off these sands in their endeavor to reach the limestone, but, there is evidence that in future more attention will be paid to

Jan 1, 1930

By R. H. Gautschi, F. C. Langenberg

Rare-earth additions were made to laboratory heats of Type 310 stainless to observe their effect on as-cast ingot structure, nitrogen and sulfur contents, and nonmetallic inclusions. Lanthanum had a grain-refining effect in 30-lb ingots, but results with 200-lb ingots were inconsistent. Cerium, lanthanum, and misch metal lowered the sulfur content when the sulfur exceeded 0.015 pct and the rare-earth addition was greater than 0.1 pct. The rare-eardh content in the metal dropped very rapidly within the first few minutes after the addition. The size, shape, and distribution of nonmetallic inclusions was not changed in 30-lb ingots, but changes were noticed in larger ingots. RARE-earth* additions have been made to austenitic Cr-Ni and Cr-Mn steels to improve their hot workability. The high alloy content of these steels often results in a considerable resistance to deformation and inherent hot shortness at rolling temperatures, particularly in larger ingots. Rare earths in the metallic, oxide, or halide form are usually added to the steel in the ladle after deoxidation although they can be added in the furnace prior to tap or in the molds during teeming. The literature- indicates that the effects of rare-earth treatments on these stainless steels are not consistent, and sometimes even contradictory. Since no mechanism has been presented which satisfactorily accounts for the claimed improvements, the effects of rare earths are a qualitative matter. The work described in this paper was initiated to expand the knowledge of the effects of rare-earth additions on melting variables such as ingot structure, chemical analysis, and nonmetallic inclusions. REVIEW OF LITERATURE Ingot Structure—Rare-earth additions to stainless steels have been reported to cause a change in primary ingot structure in that there are fewer coarse columnar grains. However, the results are inconsistent. While one investigation1 has shown a large reduction in coarse columnar crystals, another2 has been unable to observe this effect, particularly when small ingots were poured. Post and coworkers3 observed ingot structures for a number of years and found that the columnar type of structure is not definitely a cause of any particular trouble in rolling or hammering, provided the alloy is ductile. Knapp and Bolkcom4 found rare-earth additions to be quite effective in preventing grain coarsening in Type 310 stainless steel. Chemical Analysis—Many effects of rare-earth treatment on chemical analysis have been claimed in the literature. Russell5 observed that some sulfur is removed by rare-earth metals, and that a high initial sulfur content improved the efficiency of sulfur removal. Lillieqvist and Mickelson6 report that rare-earth treatment causes sulfur removal in basic open-hearth furnaces, but not in basic lined induction furnaces. Knapp and Bolkcom found no sulfur removal in acid open-hearth and acid electric furnaces, probably because the acid slag can not retain sul-fides. snellmann7 showed that sulfur could be lowered apprecfably with rare-earth additions; however, a sulfur reversion occurred with time. Langenberg and chipman8 studied the reaction CeS(s) = Ce(in Fe) + S(in Fe), and found the solubilit product [%Ce] [%S] equal to (1.5 + 0.5) X 10-3'at 1600°C. Results in 17 Cr-9 Ni stainless were about the same as those in iron. Beaver2 treated chromium-nickel steels with 0.3 pct misch metal and observed some reduction in the oxygen content. He also noted an inconsistent but beneficial effect of rare earths when tramp elements were present in amounts sufficient to cause difficulty in hot working. It is not known whether rare earths reduce the content of the tramp elements or change the form in which these elements appear in the final structure. No quantitative data are available concerning a possible effect of rare-earth treatment on hydrogen and nitrogen contents. However, Schwartzbart and sheehan9 stated that additions of rare earths had no effect on impact properties when the nitrogen content was low (0.006 pct), but served to counteract the adverse effects of high nitrogen content (0.030 pct) on these properties. Knapp and Bolkcom4 analyzed open-hearth heats in the treated and untreated conditions and found the nitrogen content (0.006 pct) to be unaffected. These two results lead to the speculation that rare-earth additions can reduce the nitrogen content to a certain level. Decker and coworkers10 have observed that small amounts of boron or zirconium, picked up from magnesia or zirconia crucibles, increased high-tem-

Jan 1, 1961

By Jie-qun Zhai, Jian Jia, Ke Yang, Xiao-lin Xie, Yu Zhang

"With cities’ development, underground space exploitation presents a need for bigger and deeper constructions now. Technical problems founded during the construction of deep foundation pit support become more and more important. The supporting system has to cut or partly cut off hydraulic connection outside and inside the foundation pit, control the ground settlement caused by dewatering and make sure safety of foundation pit and its surroundings. Some preliminary study and application of ultra-deep soil reinforcement methods have been conducted in Shanghai’s deep excavation engineering. On the basis of engineering practice of ultra-deep foundation pit in Shanghai, some field and laboratory test, this paper analyzes effects of different ultra-deep soil reinforcement methods and their influence characteristics of surrounding environment. It also summarizes these methods’ sealing effect, construction and economic efficiency and concludes their characteristicsINSTRUCTIONShanghai is formed from marine sedimentation. In Shanghai, from earth’s surface to 30~40m underground, soil is mainly consist of soft clay with 40% moisture content. There are also many thin silty-sand layers in the earth, so the soil is both soft and permeable. Under 40m, soil is mainly thick silty-sand layers and fine-sand layers with medium density and confined groundwater whose water head is about 7m high.With the rapid development of Shanghai’s municipal construction and high-rise buildings in the recently ten years, the number of underground structure including subway station, tunnel and high-rise building basement are constructed rapidly. Due to the permeability and softness of Shanghai’s soil, it is necessary to reinforce soil to make sure the safety and high construction rate of engineering project in Shanghai.Because of deeper excavation depth and bigger excavation area in Shanghai, ultra-deep soil reinforcement is used preliminarily in Shanghai. Combining with engineering practice of ultra-deep foundation pit in Shanghai and employing field and laboratory test, this paper analyzes effectiveness of different ultra-deep soil reinforcement methods and concludes these methods’ characteristics and their applicability. All this can guide further application of these methods."

Jan 1, 2015

By Tim J. Boyd

Gregg Marine, Inc. (headquartered in Signal Hill, California) has recently introduced an innovative seafloor drill system for offshore geotechnical site investigation and seafloor mineral exploration. The system is capable of working in water depths of up to 3,000 meters and is rated to drill to a depth of approximately 150 meters below mudline. The remote operated system integrates established drilling technology with proven Schilling telemetry and controls. The flexible nature of the patented wireline drilling technology enables the use of standard sampling systems (up to PQ-size core and 3? thin-walled tubes) as well as downhole testing systems (including CPT testing, vane shear testing, downhole sensors and borehole geophysical tools). The modular nature of the seabed drill system and the accompanying launch and recovery system (LARS) enables the use of local vessels of opportunity for projects resulting in reduced project costs and improved mobilization responsiveness times. Keywords: seafloor, seabed, geotechnical, drill, drilling, core, coring, sampling, CPT, cone penetration testing, borehole, logging, survey, exploration, ROV, remote sensing

Jan 1, 2011

By D. W. Holliday

The major deposits of anhydrite and secondary gypsum in Jamaica occur discontinuously at a single horizon within the Lower Eocene succession of southeast Jamaica. They are not intruded from other horizons of different age, as has previously been supposed. The gypsum and anhydrite occur in a regressive sequence at the junction between marine (Richmond Formation, Halberstadt Volcanics, Halberstadt Limestone) and overlying non-marine (Wagwater Formation) sediments. They are thought to have been formed in an arid supratidal (sabkha) environment. A variety of 'nodular' structures occurs in the gypsum and anhydrite which can be related to early diagenetic processes and compaction effects. All gradations exist between single isolated anhydrite nodules and structureless anhydrite due to closer packing and coalescence of nodules. The structures and textures in the anhydrite are thought to be consistent with penecontemporaneous formation from gypsum crystals rarely more than 2 cm in diameter. Single anhydrite nodules are not usually larger than 2 cm; nodules of greater size are compound, due to the coalescence of several smaller nodules. Some large compound nodules may have developed from single sand crystals or rosettes. Compaction of anhydrite appears to have been largely mechanical, but some rocks have an aligned fabric, suggesting later flowage

Dec 1, 1971

By Naiyang Ma

Along with fast growth of EAF steelmaking, better ways of treating EAF dust have been continuously pursued for better environmental protection and better economic benefits. In this contribution, various ways of collecting EAF dust in EAF off-gas cleaning systems are reviewed, and generation of dust and concentration of zinc in the dust from various collecting devices are examined. Accordingly, recycling of EAF dust through source separation is discussed.

Mar 1, 2018

By Igor E. Mikhaltsev

The goal of investigation of the midwaters and of the bottom of the world - ocean versus technological possibilities. Manned vehicles and maximum depth decision. The methods of solving of the problem. The science and technology alloy. Mutual venture of Academy of Sciences of the USSR and, Rauma-Repola Oy of Finland. MIR-1 and MIR-2 - as twins. No reasons of copy "Sea Cliff" and "Nautilus". Six landmarks of specificity of "MIR"-type submersibles. The manned spheres and three ballast spheres are made of maraging steel; the electric power resource (100 kwh) and maximum underwater speed (5 knots) is two times more than of the analogous vehicles while the batteries are of NiFe type; the MIR submersibles have the seawater ballast (and trim) system which means practically unlimited vertical manoeuvrability ; and the weight in air is equal to "Nautilus" - 18,6 tons (in case of equal energy resource the weight of MIR-1 or MIR-2 would be 17 tons). Some remarks on standard life support (248 man-hours) safety systems and specificity of launch & recovery system.

Jan 1, 1988

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By A. Suzue, T. H. Okabe, Y. Taninouchi

Methods for the physical separation and enrichment of platinum group metals (PGMs) from autocatalyst scrap were studied in order to develop an environmentally friendly and efficient recycling process. In general, an autocatalyst has a honeycomb-structured ceramic substrate that is coated with a catalyst layer containing platinum (Pt), palladium (Pd), and rhodium (Rh). Therefore, physical separation of the PGM-containing catalyst layer directly from the ceramic substrate is favorable for upgrading the autocatalyst scrap. In this paper, the authors present a scrap-upgrade process consisting of electroless iron plating and magnetic separation techniques. Iron was plated on the surface of a catalyst sample used to represent an autocatalyst, which was then crushed and magnetically separated. The Pd in the catalyst sample was successfully extracted and concentrated in the magnetic powder. Under certain conditions, the process increased the Pd concentration by a factor of 4 and recovered 89% of the Pd in the autocatalyst sample.

Jan 1, 2014

By L. Kühnel, H. Lieberwirth

Confined bed comminution in High Pressure Grinding Rollers (HPGR) and Vertical Roller Mills (VRM) is gaining substantial attention in many applications. Previously used mainly for milling coal or construction materials, HPGR and VRM have started to complement or even replace tumbling mills in ore beneficiation. Materials like coal or clinker are relatively homogenous, however, in comparison to metal ores and wall rocks. This characteristic poses a new challenge to the confined bed comminution but also an opportunity. Fuerstenau and Abouzeid have investigated the selectivity in comminution of a mixture of particles of different strength in a particle bed. The median particle size and particle size distribution (PSD) of the two constituents used were kept constant. Only the proportion of the two constituents was modified. The competence of a material is, however, also a function of particle size. Smaller particles tend to be more competent than larger ones of the same material. If selective comminution is applied on ores, this size influence has to be understood. The paper presents research results on this topic based on experimental investigations with model materials as well as with natural particles, which were stressed in a piston-die press. It appeared that the comminution result depends substantially on the material characteristics and the composition of the mixture. Conclusions will be drawn for the application in future applications of selective comminution in mineral processing. Keywords: Confined bed comminution, HPGR, VRM, piston die press, particle size

Jan 1, 2020