Search Documents

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By Ting Liu, Qian Li, Peng Deng

The wastewater containing Hg2+ and Pb2+ does great harm to the environment and human bodies. Traditional wastewater treatment cannot fundamentally put a stop to heavy metals pollution for producing secondary pollution. In this paper, Hg2+ and Pb2+ in wastewater were removed and recovered by sulfide precipitation- flotation. Sodium sulfide was used as precipitant and butyl ammonium aerofloat was used as collector. Results indicated that Hg2+ and Pb2+ could be reduce to less than 0.03mg/L and 0.16mg/L respectively by both coprecipitation- floatation and fractional precipitation- floatation. In these two methods, fractional precipitation flotation could not only remove Hg2+ and Pb2+ from wastewater, but also could recover mercury and lead effectively. The infrared spectrograms showed that the adsorption between butyl ammonium aerofloat and mercury precipitate or lead precipitate is chemisorption.

Jan 1, 2015

By Toshihide Takenaka

The management of radioactivated stainless steel from a terminated nuclear reactor will become an important subject in the near future. The separation of the elements in stainless steel should be effective to reduce the management labor. In this study, the separation of the elements in stainless steel by an electrorefining tcchnique was investigated in an aqueous solution. The electrochemical reactions of the elements in stainless steel werc studied by voltammetry and potentio-static electrolysis was carried out. A stainless steel anode was dissolved electro-chcmically with good anodic current etliciency in a chloride solution. The residue, where Ni was concentrated, was found on the anode after electrolysis. The electrodeposit in a stainless steel cathode consisted mainly of Fe and Cr and the Ni content in it was less than 0.5wt% under suitable condition. It is concluded that an electrorefining technique is effective for the separation of the elements in stainless steel.

Jan 1, 2003

The Bagdad mill, built in 1977, was de-signed for a mill capacity of 36,300 tpd. An ABC (Autogenous Mill-Ball Mill-Crusher) grinding circuit was chosen. The original mill contained three completely independent grinding circuits, each containing one 9.75 m diameter by 3.96 m long fixed speed autogenous mill, one 4.72 m diameter by 6.71 m long ball mill and one 2.13 m diameter short-head cone crusher. Total installed power per grinding circuit was 8,464 kw with 5,966 kw in the autogenous mill, 2,237 kw in the ball mill and 261 kw in the crusher. (See FIGURE I--Major Equipment Flow Diagram.) The autogenous mills were designed to be able to operate semi-autogenously but were never converted to SAG. As a result of this design, only about 4,100 kw of the designed power is utilized in the autogenous mills. The grinding circuits are closed with 2.44 m by 6.10 m double deck vibrating screens. Screen oversize is returned, by a series of conveyors, underneath the mill coarse ore stockpile to feed the crushers. Variable speed belts feed the crushers and control power draw. Crusher product reports directly to the tail end of the autogenous mill feed belt. (See FIGURE 2--Typical Crusher Feed and Product Size Distributions.) Tramp iron in the autogenous mill-crusher circuit is handled in a unique way. A magnetic sensor detects the metal. This closes a gate which directs the crusher feed onto a separate belt which bypasses the crusher and returns the material to the autogenous mill feed belt.

Jan 1, 1992

By H. J. Rowley

THERE are many varieties of limestone, but for the general purposes of the pulp and paper industry, two classifications are sufficient: (1) High-calcium stone, which should be quite free from impurities and contain not less then 90 per cent calcium carbonate. (2) High-magnesium stone, containing not less than 25 per cent of magnesium carbonate. Before proceeding with detail on the use of limestone and lime in the industry, a few words regarding the pulp products made in Canada are desirable. By far the largest tonnage is made by grinding spruce and balsam logs on rotating sandstones or on artificial abrasive stones of the Norton or Carborundum types. This mechanical or groundwood pulp finds its largest use in the production of newsprint paper, of which it comprises about 80 per cent of the total fibrous substance employed-the remaining 20 per cent being unbleached sulphite pulp. No limestone or lime is directly employed in making groundwood pulp, as contrasted with the chemically prepared pulps, all of which require one or the other form of the base for their processing. Sulphite pulps comprise the next largest tonnage group. They are produced by boiling, under pressure and at elevated temperatures, spruce and balsam wood in chip form in solutions of bisulphites and sulphurous acid. The usual bisulphites employed are those of calcium and magnesium. Sodium, potassium, and ammonium bisulphites give progressively better pulps, but to date, in the absence of efficient recovery methods, cost has precluded their use.

Jan 1, 1939

By Charles E. Hughes

HERBERT HOOVER had to sit through an hour and a half of eulogy of himself at Carnegie Hall last night, said the Sun and New York Herald of Feb. 19. When his turn to answer came he remarked that, although one of the speakers had referred to him as a modest man, he would never, in view of this experience, be able to prove it. The occasion was the presentation by the Civic Forum to Mr. Hoover of its medal of honor for distinguished service, the only recipients in past years having been General Goethals, Thomas A. Edison, and Alexander Graham Bell. Only by distortion of intent could there be said to be anything political in the affair, which was carefully described by the chairman, Charles E. Hughes, as non-partisan. Nevertheless, the praise bestowed on the former Food Administrator by the former Republican candidate for President, proved specially interesting to a much applauding audience which filled the hall to the uppermost gallery. A piece of real news was supplied by Horace V. Winchell, whom Mr. Hoover succeeded on Tuesday as President of the American Institute of Mining and Metallurgical Engineers. He said that Mr. Hoover, when in Europe after the . armistice, caused to be collected the literature of the war in all Europe.

Jan 1, 1920

By T. A. Klinefelter, O&apos, R. G. Meara, Glenn C. Truesdell, Richard W. Smith

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for' aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.' With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

By T. A. Klinefelter, Glenn C. Truesdell, Richard W. Smith, R. G. Meara, O&apos

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for' aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.' With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

By J. R. Woolsey

The cost of an offshore exploration project is mainly dependent on the size of the vessel engaged for the work and increases dramatically with increasing size. Of the various factors influencing vessel size, the type and size of the sampling equipment is typically the principal consideration. This scenario is particularly true of shallow sampling programs employing a vibracore system. The problem develops when certain bottom materials such as densely packed fine sand require sampling. This type of material being one of the most difficult for the standard vibracore systems, with integral core liner, to penetrate to a reasonable depth of some five to seven meters. The problem is mainly related to the excessive cross sectional area of the cutting bit required to accommodate the core liner. The typical solution has been to apply more power to the vibracore drive head which results in a considerable scale-up for the entire system with attendant increase in vessel size. In order to reduce operating cost, M.M.R.I. has developed several systems for deployment from vessels in the 20 meter range. Two systems are modifications to the basic vibracore and a third is a vibralift system. Basically, one of the vibracore units is employed where core liners are required, utilizing a special jet bit designed to reduce the cutting pressure on the bit while not affecting the integrity of the core. The other designed for core extrusion on

Jan 1, 1986

By Bryan C. Field

The proposed construction schedule for the St. Anthony Falls I-35W Bride challenged the abilities of the design-build teams to utilize the best and most efficient methods to meet Minnesota Department of Transportation?s deadlines and design requirements to restore traffic to the Interstate 35W crossing of the Mississippi River, along with a sense of normalcy, following the bridge collapse. The project team ultimately designed and constructed two foundation systems at various substructures for bridge support. Steel H-section piles were driven to bedrock for south bridge abutment support and drilled shafts were used for the north bridge abutment and piers for the Mississippi River Bridge. Drilled shafts we also used for the abutments for the three single span bridges carrying I-35W over 2nd Street. The design-build team used high-strain dynamic pile testing with a Pile Driving Analyzer (PDA) to verify H-Pile capacities and performed drilled shaft inspection on a 24-hour basis during installation over the winter months. The drilled shaft inspection process was a vital part of the project quality control program to maintain the necessary methods for proper drilled shaft installation. Ultimately, with an efficient design, quality construction methods and operation, and a rigorous inspection and quality control plan; the I-35W Bridge was opened to traffic 3 months ahead of the already accelerated schedule.

Jan 1, 2009

By Jaques A. L, Heinrich C. A

Mt Todd lies towards the south end of the Pine Creek Geosyncline, sandwiched between the Cullen Batholith and the Edith Falls Basin, in an area of regionally metamorphosed sandstones, siltstones and shales. The Batman deposit, some 3 km west of Mt Todd is a sheeted quartz vein system hosted within greywackes of the Palaeoproterozoic Burrell Creek Formation (Finniss River Group). The gold-bearing quartz veins, trending 010¦-020¦ and dipping 60¦-70¦E, are commonly 0.5 to 5 cm wide and occur at intervals which are from 10 cm to 1 m apart. Gold tends to be restricted to the quartz veinlets and immediately adjacent country rock. Grade Control utilises two 4 m 'collar' samples which are collected from each 8 m production blasthole. The irregular distribution of the quartz veins and erratic gold mineralisation has resulted in a disseminated 'salt and pepper' type of gold occurrence, with only a poorly defined footwall. Delineation of ore and waste blocks for mining uses an approach which combines the smoothing effect of kriging with a pragmatic view of the raw data. Large ore blocks with simple geometry help to minimise mining dilution, reduce block variance and give good reconciliations to interpreted ore tonnes and grade. Daily mine face advance is reported against truck counts and provides continual comparison with budgeted production. All data processing uses Gemcom software, together with Lotus spreadsheets.

Jan 1, 1994

By Tsuyoshi Hirajima, Hideyuki Okamoto, Himawan .. T. B. M. Petrus, Keiko Sasaki

"Flotation of arseno bearing minerals from their copper ore has been an interest due to the increasing awareness on protecting the environment by minimizing the possibility of exposed arsenic compound. Some approaches have been proposed, but the mechanisms of separations have not yet fully understood. In this study, oxidation using oxygen was applied. Instead of the complex copper ore flotation results, pure single mineral of tennantite and chalcopyrite foatability was conducted using Hallimond tube. Resembled with the flotation results of copper concentrate containing tennantite, the separation possessed the best result at alkaline condition (pH 11) at where the arsenic content was reduced from 3300 ppm to 1800 ppm. In order to be able to understand the mechanism of the separation atomic force microscope (AFM) was utilized. AFM images showed changes in morphology and behavior when minerals were treated in both acid and alkaline condition. It was found that the morphological change showed the reaction products representing the rate of reactivity of tennantite and chalcopyrite. From the measured force of adhesion, it can be observed that in alkaline condition the surface of both minerals is more hydrophilic than that in acidic condition possessing higher value. This is in accordance with the X-ray photoelectron spectroscopy (XPS) spectra in which hydroxide moieties occupied the mineral surface in alkaline condition while elemental sulfur is in acidic condition."

Jan 1, 2014

By G. H. Robbins

"Originally presented at TORONTO 94, CIM-AGM, this paper has been updated to reflect the present status of business development for theSO2/AIR process. The paper reviews the back-ground leading to the invention, discusses the process chemistry and historically tracks the commercial development. Engineering and cost considerations are presented.IntroductionThe year 1994 was particularly significant in terms of the technical and business development of the INCO SO2/AIR cyanide destruction process. The year marked a decade of service to the world mining community since INCO acquired the Canadian patent in 1984. In that time period, the technology had become widely recognized as the state-of-the-art process in the field of cyanide detoxification and today we enjoy the distinction of having licensed the process at over 50 project sites worldwide. The application for the process has mostly been in the mining industry in precious metal recovery plants where it offers treatment for a wide range of waste streams such as: CIP/CIL slurries, Merrill-Crowe barren bleed solutions and/or re-pulped filter cakes, tailings pond water recycle or discharge, make-up water to flotation circuits and feed to underground backfill plants. The process also applies to the treatment of high cyanide rinsewaters from metal plating shops. More recently the process is being applied to the rinsing and abandonment of heap leach pads where it has proven to be a very cost-effective application of the INCO process. The distinct advantages that have led to the success of the process are the ability to work on slurries as well as solutions and the significantly low cost of sulphur dioxide products. The process is safe and easy to manage and uses all forms of SO2(liquid, gas or salts) which gives the process tremendous versatility with respect to geographic application. Having more than ten years of service"

Jan 1, 1996

By Yanli Huang, Qiang Sun, Jixiong Zhang, Yuzhuo Jiang, Dan Ma

Mining accidents due to inrushing water are caused by sudden changes in seepage owing to structural damage to key strata of the aquiclude. The backfill mining method can be used to control the movement of the strata, weaken the evolution of fractures owing to damage by key aquiclude strata (KAS), and control the channel for inrushing water. This study develops a mechanical model of a composite beam on a non-uniform elastic foundation of the KAS by analyzing the coupling relationship between the filling body and the key water-resisting layer of the aquiclude. Equations of the deflection-induced deformation, bending moment, and maximum tensile stress of the KAS are analyzed, formulae to calculate the allowable tensile stress and backfill materials’ compaction ratio (BMCR) to ensure structural stability are derived, and are used to provide the critical BMCR for their structural instability. The results of field measurements show that the subsidence of the roof was 600–700 mm with an average BMCR of 80.63%. Damage to the overlying strata was controlled to ensure safe mining and the disposal of solid waste from the aquifer. The research here is useful for ensuring safety during mining while protecting water resources.

Jul 12, 2022

By E. M. Norris

THE Western phosphate deposits extend over a large area in the Rocky Mountain region, comprising portions of south central Montana, southeastern Idaho, northeastern Utah, and southwestern Wyoming. A limited acreage of these deposits passed into private ownership prior to Dec. 9, 1908, at which time 7000 sq. mi. of land in these phosphate fields was withdrawn from public entry by direction of the Secretary of the Interior. Under the Act of Feb. 25, 1920 (41 Stat. 437) title to all phosphate lands in the public domain was reserved to the United States with provisions for leasing portions to citizens, corporations, states, etc. The above act, in effect, created by law a Western phosphate reserve of approximately 2,269,055 acres.

Jan 1, 1944

By Shahab Alizadeh, Ahmad Khodadadi Darban, Mehdi Mohseni, Mahmoud Abdollahy

This study probed the selective separation of lanthanum and yttrium in a nitrate medium in the presence of aluminum and calcium impurities using di-(2-ethylhexyl) phosphoric acid (D2EHPA). The factors studied in a central composite design (CCD) included extractant concentration, pH, concentration ratio of total impurities to rare earth elements, and interaction of these three factors. The extraction mechanism and types of extracted metal-containing species were delineated by the slope analysis method. The obtained thermodynamic data showed that lanthanum and yttrium extraction by the D2EHPA extractant was exothermic. The extraction of both rare earth elements was accompanied by an entropy reduction. The negative magnitude of ΔS in yttrium extraction reaction suggests stronger D2EHPA-Y(III) complexation relative to La(III). As entropy decreased and enthalpy increased, the extraction process became unspontaneous. Using the proposed flowsheet, lanthanum and yttrium products with > 90% purity were obtained.

Aug 10, 2021

By Mark A. Krall

The Conda Partnership's Dry Valley Phosphate mine is a thinly bedded, multiple seam, open pit mining operation where selective mining techniques are used to recover phosphatic shales. The mining methods used are truck/shovel and scraper/ dozer operations. The ore that is mined is shipped 32 km (20 miles) by rail to a beneficiation facility which upgrades the ore via washing and calcining. The mine and beneficiation complexes are owned by the Conda Partnership. The Conda Partnership is a joint venture between Beker Industries Corp. of Greenwich, Connecticut, and Western Co-Operative Fertilizers (U.S.) Inc. of Alberta, Canada. The Conda Partnership operates as a separate entity from the two partners.

Jan 1, 1984

Three high-grade limestone ores (CaO content over than 53 %) with different geological origin have been characterized for the synthesis of aragonite precipitated calcium carbonate. Limestone ores examined in this study showed different crystal particle size that cause difference in disintegration degree and surface area of the synthesized slaked limes. The limestone ore with smaller crystal particle size showed higher disintegration degree and also yielded slaked lime with smaller surface area, which is good for the synthesis of aragonite precipitated calcium carbonate. The synthesis of aragonite PCC using the limestone with a small crystal particle size was yielded needle-shaped aragonite with the aspect ratio of about 14. Keywords: limestone, lime, slaked lime, precipitated calcium carbonate, aragonite, accelerated carbonation

Sep 1, 2012

By R. E. Wilmot

The problem of corrosion of reinforcement in concrete structures is internationally recognised and represents the single biggest expenditure in the preservation of steel reinforced concrete structures. While the corrosion protection of the reinforcing steel is no substitute for design and the placement of good quality concrete, it does provide for a viable and economical extension of structural integrity and service life in the day-to-day and practical environment in which concrete structures are constructed. The mechanism of corrosion attack and consequent deterioration of reinforced concrete structures is well understood and documented. New structures can be designed and built to withstand corrosion. However, due to short-term economical restraints, many new reinforced concrete structures continue to suffer as a result of corrosion damage, which results from the corrosion of the steel reinforcing. This paper explores the economic and practical benefits offered by the application of hot dip galvanizing as a viable means of protecting reinforcing steel concrete structures. The paper also discusses technical misconceptions that exist with respect to the application and performance provided by the use of hot dip galvanized reinforcing steel.

Jan 1, 2006

By Jan Svoboda, Toyohisa Fujita

The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation in magnetic separation are identified, advantages of this technology in comparison to other physical methods of material manipulation are discussed and reasons for its failure to live up to its potential and expectations are indicated. Derailers that were responsible for the implementation failures are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.

Jan 1, 2003