Search Documents

To Install Waste Heat Boiler at White Pine White Pine Copper Co.'s smelter 18 miles southwest of Ontonagon, Mich., will have a six story high boiler utilizing what otherwise would be waste heat from a copper reverberatory furnace. Designed and under construction by the Babcock & Wilcox Co., the boiler will supply steam to a turbo-generator furnishing power for the projected development. The boiler will be in line with and following the reverberatory furnace. Using waste heat from the furnace in place of fuel for steam generation, about 50 pct of heat in the fuel originally supplied to the furnace will be recovered by the waste heat boiler. Exploration conducted over the past 15 years at White Pine, wholly owned subsidiary of Copper Range Co., has disclosed reserves of 309 million tons averaging 21.3 lb of copper per ton. Ore mineral is chiefly chalcocite (Cu2s).

Jan 5, 1953

By Goldney L. H

The authors review the literature and discuss the application of methods to the design of thickeners for ilocculated metallurgical pulps. The use and evaluation of flocculents is described. Experimental data show that design based upon laboratory settlingdata is acceptable. The economic aspect of design is also discussed.INTRODUCTIONFor many years there has been little change in the methods for the design of thickener installations. While modifications have been made in the method of applying the data all methods have been based on the observee settling rate of the solids. The development of a theoretical approach based on physical data would involve so many variables which affect the settling rate that the more practical approach of direct observation seems unlikely to be replaced as the basis of design.The advent of synthetic fiocculents has introduced a modification in operation which affects design and should be considered. The authors review the subject and attempt to bring it up to date with present day procedure. Until recently the original work of Coe and Clevenger (1916) remained the basis of thickener design. They described their observation of the different zones encountered in settling, namely clarification, feed, transition, and compression or thickening- zones. The solids pass through the transition zone in settling from feed density to some higher density where settling ceases and ·some compression or compaction effect controls. the density obtained. The point at which the settling zone ceases to exist is known as the critical point.

Jan 1, 1959

By W. M. Hart

The remote face loading and entry convergence monitoring systems, employed at some of the Cyprus Amax's underground coal mines, have been able to continuously record changes in face shield resistance across and entry convergence ahead of the longwall face at any moment during longwall mining. The instrumental data obtained from these systems plus in-situ observations during the mining operation can help us better understand the mechanism of overburden strata movement above a longwall face and verify the effectiveness of the current face and entry supports. This paper describes the functions of both the face and entry monitoring systems, and discusses our findings and the issues related to successful ground control for longwall mining.

Jan 1, 1996

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years ago were only laboratory curiosities.

Jan 1, 1941

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years a ago were only laboratory curiosities.

Jan 1, 1941

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative face positions are tabulated for 110 subsidence monuments. Measurements were taken twelve times during the eight months it took to mine the panel. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By AIME AIME

ROBERT F. MEHL was born in Lancaster, Pa., March 30, 1898 and graduated from Franklin and Marshall College in 1919. He then went to Princeton and was granted his doctor's degree in physical chemistry in 1924. Two years as head of the department of chemistry at Juniata College, followed by a like period as National Research fellow at Harvard, working with T. W. Richards and Albert Sauveuir, satisfied Bob's immediate affections for college and university life and prepared him to turn temporarily to other fields.

Jan 1, 1938

By Qiang Zhang

Hybrid composites are fabricated by adding two reinforcements into matrix materials so that the expected excellent properties can be achieved through the combined advantages of short fibers, and different size particles (micron or submicron), which provide a high degree of design freedom. In this paper, hybrid preforms were produced with the different size reinforcement of the Al2O3 particles and short fibers. The Al-Si alloy-based hybrid composites were fabricated by preform-squeezing casting route. The structure and performance of composite materials were studied with the Transmission Electron Microscopy (TEM), and Scanning Electron Microscopy (SEM). The results show that the reinforcements, both particles and fibers, distribute homogeneously in the matrix materials, and the properties of composites are found to improve in comparison with the matrix Al-Si alloy.

Jan 1, 2009

By M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterite ores typically extracts 95% of the nickel and 91% of the cobalt. Impurity elements in the feed, such as iron, aluminium and chromium, also dissolve and can be detrimental to downstream processes. Rejection of impurities within the autoclave is highly desirable. Aluminium and iron hydrolyze, and then precipitate in the autoclave leaving only small amounts that are subsequently removed by precipitation in a neutralization step. The concentration of dissolved chromium can range from 200 to 2000 ppm, depending on the feed composition. Chromium in the liquid phase, usually in the hexavalent state, introduces many problems and can limit refining options. For example, chromium poisons the organics in solvent extraction making SX an expensive option. Also, hexavalent chromium must be converted to the trivalent state before it can be precipitated along with iron and aluminium. Bench-scale work confirmed that mixing small amounts of carbon-base additives, such as coke, with the autoclave feed significantly reduced chromium concentration in the autoclave discharge without any detrimental effects on paymetals recoveries and selectivity.

Jan 1, 2004

By D. R. BUDINSKI

Clinton Creek Mine in west-central Yukon produced 0.94 million tonnes of fibre from 15 million tonnes of asbestos ore between 1968 and 1978. The mine closed in 1978. The deposit lies along the margin of a medium sized ultramafic pluton that intrudes schistose and gneissic rocks of the Yukon Metamorphic Complex. Country rocks are metamorphic equivalents of a mixed sedimentary and volcanic assemblage deposited during Precambrian or early Paleozaic time. Movement along the north west-trending Tintina Fault System probably caused the fairly high meromorphic grade that altered the original rocks to schists and gneisses. The ultramafic pluton hosting Clinton Creek Mine is one of several bodies that were emplaced along a deep seated imbricate fault system parallel to the Tintina Trench. Most of rhe intrusions were hydrothermally altered to serpentinite, bur apparently only the one at Clinton Creek contains commercial quantities of asbestos. The Clinton Creek pluton was probably injecred slowly at relatively low temperatures into the crustal rocks as a "mush" that cooled gradually, allowing sufficient time for serpentinization and chrysotile fibre crystallizarion.

Jan 1, 1984

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi- [ ] fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Hideki Yarnarnoto

The simultaneous removal for NH4+ and PO43- in aqueous solution was carried out by using Ca type zeolite synthesized from coal fly ash. The effect of pH on the cation exchange capacity and adsorption properties of the obtained zeolite, the simultaneous removal of NH4' and ~04'. in various solutions and the mechanism of simultaneous removal were investigated respectivel? ,The Ca type zeolite used in this study can simultaneously remove NH4+ and PO43- In aqueous solution without releasing counter ion, and this method gives great advantage over the other ordinary removal methods.

Jan 1, 2002

Two outstanding features of the world's young orogenic belts are their very consistently developed suites of volcanic rocks and, it is now recognized, the rather distinctive types of mineralization they contain. Further,it is now known that these volcanic suites exhibit evolutionary patterns, and it is beginning to appear that this evolution in style of igneous activity is accompanied by a parallel evolution in style of mineralization. Specifically,podiform chromite and stratiform pyritic copper ores of Alpine ultramafic/submarine tholeiite association progressively give way to more zincian stratiform ores associated with andesites and dacites, "porphyry copper"deposits developed in quartz dioritic to dacitic plugs, and lead-zinc stratiform ores related to increasingly pyroclastic, rbyodacitic volcanism.This "coupling" is exhibited well in the volcanic arcs - the young orogenic zones-of the SW Pacific which, with tbeir abundance of youthful and commonly unmetamorphosed materials provide an opportunity for investigating, through a petrochemical approach, the possible significance of ores in the elucidation of mechanisms of lava formation. It is suggested as a working hypothesis that in the orogenic (voleanic arc) regime ores are associated with the cale-alkaline rocks because these cale-alkaline rocks are in part generated by exhalative loss, and the ores are among the manifestations of tbat loss.

Jan 1, 1978

By Ana Carolina Fernandes Reis

O objetivo do trabalho foi investigar a recuperação metalúrgica da flotação de sulfeto de ouro utilizando diferentes tamanhos de partículas, a partir de ensaios de moagem e flotação em bancada, visando analisar o melhor desempenho e seletividade do processo. O minério em estudo apresenta um teor médio de ouro de 5,28 ppm e 0,59% de S. Nos testes verificou-se uma correlação diretamente proporcional entre a recuperação mássica e metalúrgica, ambas mostraram-se inversamente proporcional a seletividade no concentrado. A granulometria com 90% passante na malha de 0,053mm obteve o melhor resultado de recuperação tanto do ouro como de sulfetos, em contra partida, apresentou o menor grau de seletividade.

Aug 16, 2017

By Marc Dondelinger

Interlocking H sections with deep webs and high section modulus are being used for cofferdams and shore enclosures where pressures are excessive. The H sections can be as much as a meter deep; they can be used as continuous interlocked wall. A steel saving alternate is spacing the H and driving deep for stability then filling between with shorter interlocking sheet piles. Templates provide for exact positioning.

Jan 1, 1985

By Jay L. Hodkinson

Replacement of an aging twin span river crossing in Vermont required a temporary bridge to accommodate traffic during construction. Soils beneath the temporary approach embankment consisted of very soft organic clayey silt underlain by interbedded, loose alluvial fine sand and silt/clayey silt. Reinforcement was required for the southern temporary approach embankment to limit settlement and to increase global stability factors of safety. A ground improvement design was developed using Rammed Aggregate Pier® reinforcement and was included in the contract documents as an FHWA Category II Experimental Feature. Instrumentation intended to document the performance of the supported embankment was installed. Piers were then constructed and monitoring commenced as embankment and bridge construction occurred. Weekly instrumentation data reports indicated continuing excess pore water pressure, settlement, and lateral deformation of the subgrade soils as the embankment and temporary bridge abutment was constructed. In response to the unanticipated monitoring results, further investigation indicated that significant deviations from the conditions and basis upon which the ground support design was developed were made during construction. This paper discusses these deviations and their specific impacts to embankment support performance, how these deviations occurred, the role that the ground support system played in maintaining global stability, measures taken to limit further detrimental impacts to the embankment, and provides recommendations for contract document preparation and construction oversight to prevent similar situations from occurring on future projects.

Jan 1, 2011

By RUSSELL S. DAVIES, Andrew Allan, John W. Buch

This is a progress report for the period February 1, 1949, to August 15, 1949, covering experiments with lightweight shearing machines for developing thin, steeply pitching anthracite beds. The over-all objective at the time an underground test section was established on July 30, 1946, was to improve mining above the gangway by developing methods for mechanization of pitch mining. Following the preliminary cutting tests in the gangway with the German machines, it became evident that the use of machines of this type indicated advantages for development work that could not be overlooked and warranted investigation. An agreement was reached with the cooperating company that this be done. Thus, the objectivo in the period covered by this report has been to obtain operating data to uso in comparing hand and machine methods of driving development openings. In obtaining the machine-mining data, 78 feet of gangway, 108 feet of heading, and 80 foot of chute work were driven. Hand-mining data are authentic for the mining condition. It has been shown that full mechanization is two and one-half times as fast as conventional hand methods on a lineal-feet- advance-per-shift basis and costs but little more than one-third as much. Tho machines are air-powered; there is less shattering of the coal bed by blasting; water sprays are used to allay' dust; coal is loaded by machine; no rock is taken; timber is not dislodgod by heavy blasting charges; and it may be said, except for the development of a means for transporting timber to the face, that the tasks for the miner are less arduous, and the working face equally as safe, or safer, than in driving by hand. Face timbering remains the greatest time- consuming cycle item, and steps are being taken to correct this. More than 50 percent of the cycle time is now usod for face-timbering work.

Jul 1, 1951

By Gary Brieley

Until well into the 20th century, most construction work was performed under the auspices of a master builder or in a manner that would be described today as design-build. In addition, many civil engineers served as ?interns? under the tutelage of a master builder in order to learn how to design and construct a certain type of structure. This was certainly the case for tunneling projects with various individuals having been identified as tunneling experts as a result of successfully completed projects The master builder approach began to change in the early 1900s to a model that would be referred to today as design-bid-build. A design-bid-build approach to project procurement gives the owner more control over the final product and al-lows the contractor to know exactly what is expected of them before the work is constructed. As a result of this transition in project procurement, civil engineering schools placed a greater emphasis on the training of ?design? professionals. This article will document how the training of tunnel design professionals progressed within the United States. Although it is difficult to generalize about the hundreds of tunnels that were constructed in the first four decades of the 20th century, there is one project that stands out as having resulted in a university program related directly to tunneling and that is the Chicago Subway. During a visit to the United States in 1938, Dr. Karl Terzaghi met a student named Ralph Peck who was then studying at Harvard University in a pro-gram established by Arthur Casagrande. Shortly thereafter, Terzaghi traveled to Chicago for a lecture and was asked to consult on the Chicago subway project that was then under construction. The Chicago subway was being constructed in clay, and the owners were worried about possible settlements to nearby buildings. Terzaghi asked Peck to serve as his field engineer for that project. Thus was established one of the most productive relationships in the history of civil engineering in the United States. Peck, who would become Dr. Peck, moved to Chicago in 1939 to participate in an extensive research project that con-tinued until subway construction was halted in 1941 because of World War II. During that time, the cost of subway construction in Chicago was reduced substantially as a result of Peck?s observations and Terzaghi?s recommendations. In fact, it was reported that subway construction in Chicago cost less than one-half of similar projects in London even though the clay in London is considerably stiffer compared to Chicago. Upon the completion of his work on the Chicago Subway, Peck accepted a professorship with the University of Illinois in Champaign/Urbana.

Jun 1, 2010

By Alicia Esther Ares, Carlos Enrique Schvezov, Alejandra Silvina Roman, Claudia Marcela Méndez

In this paper the structure of aluminum based alloys and their corrosion behavior by using different electrochemical techniques as characterization methods are considered. Currently, it becomes imperative to know the role of the Al2Cu against the susceptibility to corrosion of these alloys. The present work aims to studying the electrochemical behavior of aluminum base alloys with the following compositions: Al-1wt.%Cu, Al-4.5wt.%Cu and Al-15wt.%Cu (with different grain structures), in 1M NaCl solutions, at room temperature. Cyclic potentiodynamic polarization tests were performed and were found that the alloys with more than 1wt.%Cu in the matrix have an unstable behavior and without tendency to reach passivity. The equivalent circuits derived from electrochemical impedance spectroscopy technique (EIS) generally showed two capacitive contributions. The susceptibility to corrosion becomes a complex function, not only of copper concentration and structure, but also with interdendritic spacings and distribution of phases in the alloys.

Jan 1, 2015

By D J. Williams

Tailings management is typically constrained by many factors that are taken as given. These include the tailings production rate that must be accommodated, the desire to deliver the tailings cheaply and easily as a slurry using centrifugal pumps, and a tailings footprint limited by the desire to minimise capital costs leading to a rapid tailings rate of rise and a low settled density. Other constraints include wall raises being delayed due to limited capital, inadequate tailings water and rainfall run-off management, and the net present value (NPV) approach to capital expenditure that puts off expenditure at the expense of performance. All of these constraints result in the tailings occupying much more volume than is necessary, being difficult to rehabilitate, and not being capable of supporting a beneficial post-mining land use or function. Ultimately, such constrained tailings storage facilities will assume very large dimensions, but each will typically be developed as a series of smaller storages that are filled rapidly and added to progressively. The optimal stage to efficiently recover process water is in the process plant, but this is limited by the desire to use centrifugal pumps rather than the more costly positive displacement pumps, which also require greater management of tailings deposition. Process water can also be recovered from the tailings storage facility (TSF) decant. Tailings water that is not recovered from the plant or the decant will be lost to entrainment within the tailings, seepage to the foundation or through the wall, or evaporation. However, tailings water is not always suitable for reuse in the plant, particularly when it becomes contaminated by the processing, and it may simply be stored on the TSF. This will exacerbate the seepage of contaminated water to the environment, and will limit the densification of the tailings that would otherwise occur due to desiccation of the tailings on exposure. If a larger tailings footprint were developed early, cycling of tailings deposition in thin lifts between a number of cells could occur, maintaining the dormant cells dry to enhance desiccation and densification, and ultimate rehabilitation. The end result would be a much reduced stored volume of tailings, the potential for upstream raising, and ease of rehabilitation to a high level. The higher initial capital cost would be overtaken by reduced ongoing capital, operating and closure costs.CITATION:Williams, D J, ?2014. An alternative whole-of-life approach to tailings management, in Proceedings Life-of-Mine 2014 , pp 285–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014