Search Documents

By L. Seigle, R. Resnick

An inert-marker movement experiment indicates that the ratio of the intrinsic diffusion coefficients DC:DTa = 80:l in TaC at 2500°C. Measurements of the diffmion coefficient of carbon in nonstoichiometric TaC at temperatures from 1700° to 2700°C reveal that Dc increases with decreasing carbon content, but much less than expected from the probable change in vacancy concentration with carbon content. A diffusion process involving two simultaneously operating mechanisms is postulated, and shown to be theoretically feasible. The average value of the carbon diffusion coefficient is given by DC = 0.18 exp[(-85,000 ± 3000)/RT] sq cm per sec over the composition range 46 to 49.5 at. pct C. BECAUSE of their high melting points and hardness, the carbides of the IV, V, and VI group transition metals, along with those of uranium, have attracted considerable interest for applications at high temperatures. In these applications the reactivity of the materials is important, and, since rates of diffusion within the compounds influence reactivity, a knowledge of diffusion kinetics and mechanisms is desirable. While many investigations of the mechanical and electrical properties of these compounds have been made, only two fundamental investigations of diffusion in the carbides are known. Chubb, Getz, and Townleyl measured the diffusivity of carbon and uranium in UC, and Gel'd and Liubimov2 measured the diffusivity of carbon and niobium in NbC. This paper describes an investigation of the diffusion of carbon in tantalum monocarbide and, in particular, the influence of carbon deficiency on this process. Tantalum carbide melts at approximately 3800°C, which makes it one of the highest melting materials known. The compound exists over a rather wide range of carbon Content.3-7 At the peritectic temperature, 3240°C, the phase extends from about 36 to 50 at. pct C. Although the compound can exist with a substantial carbon deficiency, the high carbon phase boundary remains near the stoichiometric composition over the entire temperature range; i.e., no carbon excess is observed. The structure of TaC is the NaCl type wherein carbon atoms normally occupy the octahedral sites in a somewhat expanded fcc lattice of tantalum. Decrease of the lattice parameter with decreasing carbon suggests that the removal of carbon introduces octahedral vacancies into the lattice. I) EXPERIMENTAL DETAILS AND RESULTS Inert-Marker Experiments. In a compound such as TaC the interstitial element would be expected to diffuse more rapidly than the metal. This was confirmed by an inert-marker experiment, following Srnigelskas and irkeendall.8 Ideally, the markers should be placed at the interface between a slab of low-carbon TaC and graphite, and their movement during subsequent inter-diffusion measured. Unfortunately, no solid could be found which is unreactive in contact with carbon at the high temperatures employed in these experiments. In order to circumvent this problem, a specimen was designed in which the markers consisted of several small canals running just below the surface of a tantalum slab. This specimen was prepared by machining grooves on the surface of the tantalum slab and then diffusion-bonding a thin plate of tantalum to the slab over the grooves. The surface of the plate was then ground down until the distance between the canals and surface was as small as possible (about 0.01 cm). Thus, the canals would lie entirely within the TaC phase after a short period of diffusion. The diffusion anneal consisted of immersing the metal sample in high-purity graphite powder and heating for approximately 10 hr at 2500°C under vacuum. At this temperature, the vapor pressure is sufficiently high and the transfer of carbon from graphite sufficiently rapid to allow the surface of the diffusion sample to attain the stoichiometric carbon concentration very quickly. Conclusions regarding the relative diffusion rates of carbon and tantalum in the compound layers (TaC and Ta2C) can be drawn from the location of the canals after the diffusion anneals. If the growth of the layers is governed mainly by the diffusion of carbon, as expected, the canals should remain close to the sample surface. If the diffusion of tantalum contributes appreciably to formation of the compound layers, the distance from the markers (canals) to the surface should increase. Fig. 1 shows, diagrammatically, the appearance of the specimens after diffusion, and Table I presents the depth below the surface at which the

Jan 1, 1967

By L. "Andy" Anderson, Stephen N. Short, James E. Friant

Since the introduction of "boxhole" drilling in South Africa in 1973, the concept of a blind raise, drilled upward from below, has become an accepted mining practice. A combination machine, capable of constructing raises to a mining level below, or blind raising upward from a single setup position adds a further dimension in versatility. A machine with these dual operating modes was designated by The Robbins Company as the 53R and was introduced into the Western Deep Level Mines, South Africa in 1984. The unit is powerful (200 hp) and compact (18,000 lbs., in a 10 ft x 4 ft 5 inch x 4 ft 6 inch package). This paper describes the design considerations for the new machine, provides field data from early trials, and looks briefly at its overall market and potential.

Jan 1, 1985

By S. W. Parr, T. E. Layng

The low-temperature carbonization of coal involves the carrying out of the coking process under conditions wherein neither the coal mass nor any of the passageways through which the volatile products pass are heated above 700" or 800" C. For convenience in this discussion, the single number 750" will be used to designate the maximum range. This temperature is not selected arbitrarily; it is the result of certain natural conditions that are inherent in the substances involved. Two of these conditions arc sufficiently pronounced to suggest a line of demarcation at this point as follows: (1) Below 750°, all the heavy hydrocarbons are expelled, which means that, at these lower temperatures, the illuminants, the gases of high calorific value, and the condensible oils are discharged; above 750") there are given off the lean, non-illuminating gases consisting for the most part of hydrogen and marsh gas and having no condensible constituents present. (2) Below 750") there is substantially no secondary decomposition; above 750") the volatile products are readily decomposed, forming tars, naphthalene, free carbon, etc. It is not intended to maintain that no secondary decompositions occur below 750". Many recent studies have demonstrated the practicability, especially in the presence of catalytic substances, of cracking certain of the hydrocarbon compounds; but at these lower temperatures the step is a moderate one, as, for- example, from xylene to toluene or from toluene to an anthracene. These changes are moderate in amount. Not only do the reactions proceed slowly but they are subjected to the decomposing . conditions for only a short time. This is evident when it is recalled that at these initial temperatures the decomposition of the coal is very rapid and, if anywhere near a neutral pressure is maintained, the movement of the evolved gases is lively and reduces, correspondingly, the time for the retention of the gases in the passageways where these milder decomposing conditions exist. It is acknowledged that the maintenance of these temperature conditions at the present time has only an ideal and not a practical status. Actual operations under these conditions, as a? industrial accomplish-

Jan 1, 1920

By S. Ramachandran, L. A. Vazquez, N. L. Grauerholz

A novel process is described for the selective flotation of scheelite from low-grade (- 0.5% W03) tungsten ores having appreciable quantities of calcareous and siliceous gangue minerals. Specifically developed for the Tempiute, Nevada facility of Union Carbide, the process yields tungsten concentrates exceeding 15 percent W03 with at least 85 percent recovery. This condition was not achieved through conventional processes. This process consists of conditioning the ore pulp with judicious amounts of lime, followed by soda ash and sodium silicate as modifiers. The scheelite is then floated using a mixture of oleic and naphthenic acids as collector. Contrary to the common observation as to the deleterious effects of calcium in fatty acid flotation systems, lime addition is found to be beneficial in achieving satisfactory results. The process has also shown excellent results on a Brazilian scheelite ore.

Jan 1, 1976

By L. B. Hales

The advent of the process control computer with its capabilities of monitoring, storage, and real-time control has revolutionized control technology in the mineral industry. Initial efforts to introduce the computer into process control began in the early 1960's. However, it wasn't until the last decade with the introduction of integrated circuits and minicomputers that truly successful applications became visible. Computer hardware and real-time operating software have improved to the point that they rarely provide major problems in the implementation of successful control systems. At this time the most prevalent problems and obstacles affecting the successful implementation of a control system are as follows: (1) reliable and representative sampling systems; (2) rugged and reliable process sensors; (3) the availability of well-defined control strategies; (4) the willingness of plant management to provide the continuous support necessary to acquire and/or train appropriate personnel in the operation and maintenance of advanced control systems. Discussion of these problems and of the instrumentation required for the successful application of computers in minerals processing plants follows. In order to enhance this discussion the remainder of this subsection is broken up into individual mineral processing categories.

Jan 1, 1979

The task of designing stable high walls and spoil piles in strip coal mines, and stable openings with controlled roofs and floors in underground collieries - within the constraints normally imposed by economics - depends upon a reliable assessment of rock mass strengths and rock mass reactions under a variety of stress conditions. Of the geological factors influencing internal friction and cohesion within rock masses, many may be determined qualitatively or empirically from bore-hole evidence. Rock types, descriptions and properties of intact rocks, location of boundaries, limits and degrees of weathering, potential for slaking or decomposition of rocks when exposed, bedding characteristics, the nature of rock anisotropy and the likely effects of water on rock mass properties can be assessed from bore- hole data. Discontinuities, whether they be major such as faults and dykes, or minor such as joints and fractures, present a greater problem, and in most instances the mine geologist must resort to additional techniques to describe or predict their occurrence, nature, frequency, intensity or physical properties. Information on ground water and seam gas is available from bore-holes within certain levels of reliability.

Jan 1, 1977

How to Evaluate Crushed Rocks for Concrete Production

Sep 13, 2010

By A. K. Martin

Adaptive management can be described as a structured, iterative process of robust decision making in the face of uncertainty, with a goal of reducing uncertainty over time through system monitoring. Adaptive management is a tool which can be applied to not only change a system, but learn about the system (Holling, 1978). Adaptive management has been used in ecosystem management for years and guidance is provided in a variety of handbooks and publications. Adaptive management can be applied to industrial facilities and mines through the use of an adaptive environmental management plan (AEMP) and associated practices. The goal of this paper is to provide an explanation of how the plans and practices support regulatory agency approvals and permitting, span the life-cycle of mines, manage uncertainty, and assist in addressing mining impact and legacy issues. AEMPs and associated practices are useful tools to address the uncertainties in identifying, evaluating, and managing impacts of proposed new and modified mining facilities undergoing environmental review. Once a proposed project is approved, the AEMP continues as a living document, being informed, revised, and adapted by the operations. The AEMP can serve as an ongoing management tool for describing and evaluating environmental impacts, continuing in operations into post reclamation. If initiated during planning and environmental review of a project (and in some locations such as the United States [U.S.], the preparation of an Environmental Impact Statement (EIS)), the AEMP becomes a basis to identify, monitor, and manage potential project environmental impacts. Development of an AEMP for an operating mine is also beneficial since there are generally developing and ongoing environmental issues at those facilities as well. Over time, the AEMP is adapted to changing requirements and conditions including those anticipated and unanticipated. Ever increasing scrutiny of mining projects and the complexities of the EIS process highlight the uncertainties inherent in impact predictions. In making the momentous decision of initial project approval, these uncertainties can discourage the regulatory agencies? actions and create stakeholder anxiety and controversy about a project. A well-designed AEMP can support the decision to approve an EIS and enable a project to move forward. Additionally, an AEMP can inform financial assurance estimates and revisions over the life of a mine providing all parties including the citizens of the surrounding communities with greater confidence that potential environmental impacts and risks will be well managed.

Feb 23, 2014

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By Hylton R. Brown

This publication, an abstract of a progress report covering an investigation of hazards in thermal coal-drying plants has been prepared according to the suggestions and recommendations of a committee6/ appointed by J. J. Forbes, Director of the Bureau of Mines, when the original report was reviewed at a meeting of representatives of the mining industry, operators of coal-drying plants, coal-mine workers, and the Bureau in Washington on May 6, 1955. The investigation on which the report is based was made in accordance with action taken at a previous conference in Washington on May 19, 1954, called by Director Forbes to consider what should be done to prevent explosions and fires in coal-drying plants. Scope of Investigation The investigation was planned to obtain information considered essential for properly appraising fire and explosion hazards in different types of coal driers. A questionnaire sent to Bureau personnel provided preliminary information on coal-drying facilities at more than 270 preparation plants. Information on methods used in operating different types of driers, with their furnaces, fans, cyclones, and other auxiliary equipment, was obtained by personal visits or conferences with the operators at 13 plants. Factual data on operating temperatures, composition of the drying gases, air flow, dust loading of the air or gas currents, use of water sprays, auxiliary air controls, and other factors were obtained by conducting full-scale tests at six different plants and making laboratory investigations with samples of dust and gas collected during the tests.

Jan 1, 1956

By T. S. Lovering

The use of geothermal energy is expanding very rapidly. This type of energy has proven commercially profitable for generation of electricity, for space heating, process heating, auxiliary heating of water in conventional steam power plants and for recovery of chemicals contained in natural hot water and steam. Two types of geothermal energy sources are recognized: 1) hot springs in regions of nearly normal heat flow that tap a deep reservoir through which water moves slowly to a hot springs conduit and then rapidly to the surface; 2) hyperthermal areas in which the water is heated by a relatively concentrated heat source related to volcanicity. If there is a geologic trap that provides a geologic analog to a steam boiler, as at Larderello, Italy, the hyperthermal area will have a convecting system that develops superheated water at relatively shallow depth and may provide natural steam in large quantities. If a hyperthermal area is to be productive for a long time, the underflow into the reservoir should be slow enough to allow the heat source and convective system to heat the underflow to the working temperature, and the production rate must not exceed this rate of underflow. A model based on a typical aquifer suggests that the rate of movement of water through the reservoir be such that a few years are spent in transit between isotherms that are spaced about 2°F apart. The possibility of finding blind geothermal areas is illustrated by discussion of the techniques developed in evaluating the subsurface temperatures in the East Tintic district of Utah where a map of isotherms at water level (2000 to 2000 ft below the surface) shows that a hyperthermal area may exist a short distance southeast of the mining district. Very nearly all of the energy that man currently uses comes ultimately from the sun's radiation. This includes water power, fuels such as wood, peat, coal and petroleum, the wind and all our animal power. In the paper summarizing a conference on solar energyl6 the average amount of solar energy received daily on the earth is taken at about 1 cal per m2 per min or slightly less than 2 pcal per cm2 per sec; this is almost exactly the amount of energy on the average that the earth liberates in regions of normal geothermal gradient due to its own internal heating. In many places, however, the energy released is many times the average and in some of these hyperthermal areas, geothermal steam is used for generation of electricity, and hot springs are used for heating buildings and private dwellings, process heating, auxiliary heating of water in conventional steam power plants, and chemicals may be recoverable from both hot water and steam. The use of hot springs waters for heating houses goes back hundreds of years but until recently was confined to a few dwellings close to the hot springs. In Korea, some houses had hot spring water channeled through conduits in the floor centuries ago and thus the Koreans can be credited with pioneer development of radiant heating. In Iceland at present nearly a third of the population uses natural thermal water for domestic heating." The Reykjavik system pipes hot spring water at about 94°C throughout the city and has devised insulated double pipes that allow the water to be piped for some 25 km with a drop of only 1°C for every 5 km. The actual cost to the Icelandic consumer is only one-third the cost of heating by imported coal and yet the industry is one of the most profitable in Iceland. The most profitable use of geothermal energy has been its conversion into electricity which can be transmitted economically much greater distances than hot water. The largest installation at the present time is that at Larderello, Italy, where the Count of Larderello began to experiment in the production of electricity from geothermal steam 60 years ago — in 1904. He installed his first steam turbine, with a capacity of only 250 kw, in 1912 as the result of a local quarrel with the power company which furnished the current required in the Larderello chemical industry - an industry that then dated back nearly a century. As experience was gained in drilling deep holes to tap geothermal steam and in converting it to electric power, the capacity of the installation of Larderello gradually increased, but was all destroyed by the Germans during their retreat from Italy in the closing

Jan 1, 1965

In preparing a paper such as this it was thought that the Newstan Colliery Company Ltd., being comparatively new, would need some introduction to mining people in general.The Newstan Company was formed by the Joint Coal Board in December, 1948 during a period of acute coal shortages. The Company took over the holdings of what were known as the Olstan and Northumberland Collieries, situated at Fassifern, alongside Lake Macquarie and adjacent to the Great Northern Railway, within easy rail access of Sydney and Newcastle, as shown on the locality plan (Fig. 1).The Company was developed in order to produce steaming coal for the power house trade and has continued its activities in the steaming coal trade since its inception. The Olstan and Northumberland collieries were together producing some 300 tons per day when the Company was formed, and it was from this foundation that the colliery was built. The planned development of the Company has been along the lines of producing coal by modern, highly mechanised methods, together with the preparation of theproduct for the consumer, to the highest degree possible consistent with up to date methods.In the comparatively short time of 5t years the mine has developed from a small hand-won coal unit to a high capacity modern mine, one of Australia's largest producers, with an output capacity as high as 3,000 tons per shift.

Jan 1, 1954

By Thais Cristina da Costa Caldas, Alline Sardinha Cordeiro Morais, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

"This work has as its objective to evaluate the firing behavior of a kaolinitic clayey body from Campos dos Goytacazes-RJ incorporated with flat glass waste (FGW) from civil construction. Incorporations of the waste, with a particle size less than 74 µm (200 mesh), were performed in the red ceramic in the following amounts: 0, 2.5, 5 and 10 wt%. Specimens were prepared by uniaxial press-molding and then fired at 850 and 1050°C. The characterization of FGW was done by X-ray Fluorescence. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The microstructure of the fired ceramics was evaluated by optical microscopy (OM). The obtained results showed that the flat glass waste can be used as a component of ceramic bodies once it was noticed tolerable modifications of technological behavior.IntroductionBrazil is one of the world’s largest producers and consumers of clayey ceramic. Campos dos Goytacazes is located in the north of the State of Rio de Janeiro, southeast of Brazil, it’s known as a large producer of red ceramics. It is estimated that the production of bricks can reach 1 billion pieces per year [1].Nowadays, recycling processes became more and more important, due the generation of wastes in large scale and the preoccupation with environmental. The amount of glass waste has been exponentially growing with the growth of the population. It is estimated that the amount of discarded glass as bottles, construction windows, packing and other glass waste represented in 2006 an amount of 7.5% of the total weight of the world´s domestic garbage [2]."

Jan 1, 2012

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state-of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-term underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results froman extensive series of Schmidt Hammer tests found that the shotcrete increased in strength by 70% during the humid summer months.

By J. C. Watts

Ball mill grinding circuit control has received increasing emphasis in the past few years due to such factors as declining ore grades, increasing production costs, and advances in analytical devices and minicomputer technology. Since ball mill circuits have been a traditional bottleneck in mineral processing plant throughput, control systems often improve through- put without requiring additional processing equipment. In addition, much of the variability of the grinding product size and consistency is often removed, allowing better process operation downstream. Among the problems which arise in designing and implementing a process control strategy for ball mill circuits are circuit constraints imposed by processing equipment and local management, proper instrument selection, installation and maintenance, and use of calculated or inferred variables for process measurements. This paper discusses these problems and attempts to identify valid approaches to their solution.

Jan 1, 1979

By A Rantala, C Cruickshank, I Muzinda, O Haavisto, J Timperi

The production at First Quantum Minerals’ (FQM) Kevitsa Mine, located in northern Finland, commenced during the second quarter of 2012. Presently, the mine processes approximately five and half million tonnes of ore annually, producing nickel, copper and platinum group metal (PGM) concentrates. In order to support fast production ramp-up and optimise the performance of flotation thereafter, an extensive advanced flotation control solution was implemented by Outotec in collaboration with FQM Kevitsa.In addition to basic process instrumentation and process control, each of the 14 Outotec 300 m3 and another 26 cells, ranging from 20–160 m3, have been equipped with state-of-the-art systems providing froth image analysis and automatic froth speed control. Also, the flotation cell levels are stabilised with advanced feed-forward level control.The online analyser provides key feedback information of the process performance for the advanced process control (APC) system. Based on this information, APC system defines grades and recoveries according to rules defined by Kevitsa process metallurgists. This system executes the control strategies for optimising the production of concentrates.Throughout the implementation and support phases, specific and intensive attention was paid to ensure plant personnel gained full understanding of interacting with the system and how to incorporate their process experience and skills to optimise the APC strategy. This level of expertise is also a valuable asset in understanding the APC system’s contribution to the overall performance of the plant as well as providing the ability and confidence to define key performance indicators used for continuous assessment. The experiences and results from site achieved so far are discussed in this paper.CITATION:Rantala, A, Muzinda, I, Timperi, J, Cruickshank, C and Haavisto, O, 2014. Implementation of advanced flotation control at First Quantum Minerals’ Kevitsa mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 369–378 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R. Addison

This is the story of the Carlton Mill. But first-a little geography. For those who do not know where the Carlton Mill is, or, perhaps, have only a vague idea, its location is indicated in Figure 1. The plant is situated on the road between the two old mining towns of Cripple Creek and Victor, 10 the west of Colorado Springs. From Denver, it's about 110 miles by road. The story of the Carlton Mill began with the discovery of gold at Cripple Creek in 1890. This discovery set off a major boom such that, by the turn of the century, there were 450 separate operating mines in the district. Gold production boomed early and declined rather rapidly as indicated by the graph in Figure 2. Significant factors affecting production are shown on the graph-the raising of the gold price in 1934 from $20.67 to $35.00 per ounce and the government executive order L-208 in 1942 requiring the closure of all gold mines.

Jan 1, 1983

By Maurice A. Ponti

The D.C. Water and Sewer Authority is implementing the Anacostia River Projects component of its Long-Term CSO Control Plan, including 21 kilometers of 3.7- to 7-meter-diameter CSO near-surface diversion storage/conveyance structures and flood relief, pressurized-face, soft ground tunnels at a maximum depth of 65 meters. This paper describes a project-specific soil grouping system that is primarily based on soil characteristics for tunneling derived from tests including Atterberg limits, grain size, swelling, mineralogy, triaxial, pressure meter, and consolidation, which differentiates the project from past area tunnel projects using descriptive systems based primarily on area geology.

By K. Kabezya

A study on slag dispersion in a model of bottom-blown bath smelting converter was undertaken at room temperature. The aim was to investigate the behaviour of the dispersed slag phase at various operating conditions with very high gas flow rates in low slag volume (10%) systems. For simulation purposes water, paraffin-oil, and air were used to represent the bulk steel, molten slag, and gases respectively in a one-fifth cold model of the commercial 100 t Creusot-Loire-Uddeholm (CLU) converter used in the manufacture of stainless steel in South Africa. Dimensional analysis was done to correlate mathematically the dispersed phase holdup with the operating conditions and the modified Froude number. The overall expression of the holdup revealed that the dispersed slag phase decreased with the vertical distance from the original interface between the liquid phases. The dispersed phase also decreased with the radial distance in the water plume zone toward the sidewall. The holdup was apparently much higher on the side of the reactor where there were no tuyeres. The modified Froude number ensured the correlation between the model and the prototype.

Jan 1, 2014