Search Documents

By C. H. Mahoney, P. E. LeGrand, A. L. Tarr

MAGNESIUM, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, on the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.1 Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point. It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-bearing group by raising the temperature of the melt after the refining treatment to some 25e C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730° C. (1350 F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (1600°F.) and 930°C. (I700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.2 It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying constituent-the binary alloy containing r.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery. During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack formation, as well as grain size, and a discussion without any definite conclusions on the theoretical aspects of superheating. A short article by Murphy, Wells and

Jan 1, 1945

In this study, the method of chemical co-precipitation?reduction?diffusion was developed for the preparation of magnetic SmCo5 alloy. In the chemical co-precipitation process, the effects of solution pH, the reactant concentration, the dispersant on the process were investigated. The optimum conditions of the process were determined, and the SmCo5 alloy oxide precursor particles with fine crystalline structure, narrow size distribution was obtained. Then, by reduction-diffusion treatment of the precursor particles, the SmCo5 alloy with high quality was produced. It is anticipated that the co-precipitation-reduction-diffusion is a novel method available for SmCo5 alloy production.

Jan 1, 2006

By Russel Delmar, Rick Everdell, Harry Charalambu, John Tait

Award of the Design/Build Agreement for construction of Ontario Power Generation’s (OPG’s) Niagara Tunnel Project was made after an intensive 8-month international procurement process. The 14.4-m diameter × 10.4-km long rock tunnel will divert 500 m3/s of water from the Niagara River to the Sir Adam Beck hydroelectric generating complex. The procurement process and Design/Build Agreement included features to address the owner’s requirements regarding risk allocation and cost and schedule certainty, while encouraging innovative ideas from the industry, both technically and commercially. The process included an international expression of interest and prequalification, followed by an invitation for design/build proposals to qualified proponents, and comprehensive proposal evaluations and negotiations with several respondent proponents. An honorarium was provided to the unsuccessful participants in the proposal stage. The resultant negotiated Design/Build Agreement includes Owner’s Mandatory Requirements, negotiated contract terms and conditions, performanceincentive bonuses and liquidated damages for schedule and water delivery performance, a multistaged Geotechnical Baseline Report, joint risk management, references to preexisting community impact agreements and measures to reduce impact on tourism. It also addresses regulatory approvals and permits, an owner controlled insurance policy that required reference to the International Tunneling Insurance Group (ITIG) Code of Practice for Risk Management as a condition of coverage, site specific safety, security and environmental plans, formal team building, a dispute review board, and escrow documentation.

Jan 1, 2007

By J. H. Rushton, L. H. Mahony

Principles of fluid motion and turbulence which have been found to be of use in mixing and agitation problems are discussed, as well as suggested applications in extractive-metallurgy processes. Various types of impellers are described, together with other conditions that affect flow pattern and turbulence. The choice of equipment for particular requirements is considered, and equations for power input are given. Modern heavy-duty mixing and agitation equipment can take an increasingly important part in such extractive-metallurgy processes as solids handling, crystallizing and leaching, chemical operations, and flotation. Application of mixing and fluid-mechanics principles to extraction methods can lead to greater process rates and a resultant saving in time and money. MIXERS are being applied with increasing frequency to problems in the metallurgical industries. The increase represents in part the modernization of mechanical equipment used through the application of unitized drives, modern electric motors and speed reducers, and recently developed materials of construction. Some applications have resulted from process changes and the use of techniques for operations similar to those that have been demonstrated and proven in the chemical industry. Still more applications are being developed through the use of fluid-dynamics principles not previously recognized as applicable to these operations. It is the purpose of this paper to describe those principles of fluid motion and turbulence which have been found to be of use in mixing and agitation problems, and to suggest applications for them in the extractive-metallurgy processes. Modern mixing equipment has been designed to provide the fluid motion consistent with that best suited to different operations.' When properly applied, these more efficient fluid-handling mixers result in lower process-production costs. Metallurgical operations usually involve large amounts of solids. The characteristics of the ore control the process and only enough liquid is added to provide sufficient fluidity for handling and processing. The reactive part of the ore, the mineral value to be extracted, is likely to be low in percentage, and the quantity of reagent required is similarly low, but excessive dilution makes additional reagent necessary and therefore is undesirable. Thus, the primary problems in minerals processing are to handle as high a concentration of solids as possible and to distribute reagents uniformly. These pulps, or slurries, are in a range of solids concentration where hindered settling rates apply, and care must be taken to agitate and mix sufficiently to maintain suspension and flow throughout the equipment. Such slurries have high densities which are the weighted average of the components and viscosities that are spoken of as "effective viscosities" but are difficult to evaluate. It is convenient to separate metallurgical operations involving mixers and agitators into three categories: solids handling, mechanical or physical operations, and chemical operations. In each of these categories fluid motion is required to maintain suspension, to distribute surface-active agents, to blend components and reactants, and to induce high rates of chemical reaction. After a discussion of some basic principles of mixing and agitation, examples of application to the three categories will follow. Fluid Motion The fundamental problems of mixing and agitation of liquids have to do with the mechanics of fluid streams and the means by which they are

Jan 1, 1955

By H. Suharyono

The results of an experimental study of polymer-induced flocculation of clay suspensions in continuous, stirred-tank reactors are presented. The effects of polymer dosage, mixing time and mixing intensity are shown to be generally similar to those observed for equivalent batch systems, but flocculation appears to be generally less effective in the continuous process. Settling rates are lower and supernatant turbidities are higher for the continuous system. It is postulated that non-equilibrium effects due to simultaneous polymer adsorption and floc growth can be exploited so as to enhance flocculation in batch systems. The nature of the continuous process, however, offers less opportunity for taking advantage of such effects. Conditions in a continuous flocculation system inherently lead to a closer approach to equilibrium.

Jan 1, 1994

By John E. Husted

Quantities of kaolin in Georgia in-contiguous or single bodies had been established by previous work to be sufficient for an alumina industry. The need for characterization of this kaolin to determine its suitability as an ore of aluminum resulted in the studies described herein. It was determined in an area roughly 7 x 27 miles, known as the Wrens district that approximately 5.9 billion short tons of kaolin averaging 35.55 percent A1203 exist in an essentially continuous clay body. The Macon-Sandersville district consists of discontinuous kaolin bodies averaging 35.28 percent A1203 with an average thickness of 28 feet. Tonnages for this district are not available. One hundred and twenty core samples of kaolin were analyzed for K20, CaO, MgO, Al203, T102, Cr203, Fe203, Si02, P205, and F. The P205 and F were analyzed by wet chemistry methods and the others by electron microprobe. Seventy-nine of the samples were from the Wrens district forty from the Sandersville-Macon district and one from the Andersonville district. Emission spectroscopic analyses were also made to qualitatively determine all elements present for each core. X-ray diffraction studies were made of each core to determine mineral species present. Scanning and transmission electron microscope pictures also are given for each I' core sample. Elevations, overburden thickness, and kaolin thickness are given for each core site as well as map locations. Isopachs for over-burden and kaolin thickness are given for the Wrens district.

Jan 1, 1983

By N. Brown, H. Green

The effect of quenching temperature and of aging temperature and time on compression stress-strain curves of ß brass was investigated. Age softening occurs at a rate which decreases with decrease of quenching temperature below the critical temperature for ordering. The activation energy for softening is 15,400 cal per mol. No matter how rapidly brass is quenched or what the temperature from which it is quenched, practically complete order is obtained at room temperature. It has been demonstrated that with respect to the specific heat,',' electrical resistivity," X-ray diffraction, and microstructure, the slowly cooled and rapidly quenched specimens are the same and that complete long range order exists in both cases. However, Smith" showed that the hardness of ß brass depended upon the cooling rate and the temperature from which brass is quenched. Smith showed that the hardness was a maximum for specimens quenched from about 445 °C and that the as-quenched structure softened at room temperature at a rate depending upon the temperature prior to quenching. This softening after quenching is in this paper referred to as age softening. The results of this investigation are qualitatively the same as the findings of Smith. However, a more detailed analysis of these phenomena has been possible since the stress-strain curve offers a more sensitive index of the state of the metal than hardness. It is the purpose of this paper to show how the mechanical properties are related to the ordering of ß brass. A 200-lb ingot made from electrolytic copper and electrolytic zinc was extruded to 1/2in. rod. Chemical analyses at frequent intervals along the rod showed that the alloy contained 51.5 pct Cu with the greatest impurity being iron, at 0.01 to 0.001 pct. To obtain a constant test material, the 1/2in. extruded rod was warm-rolled to % in. diameter at 200°C and then recrystallized to a grain size of 2.0 mm. The specimens for the compression test were % in. high and % in. in diameter. The specimen ends were polished on 600 metallographic paper and coated with Molykote for a lubricant. The compression rig consisted of an anvil resting on the machined table of the Baldwin Southwark testing machine and a plunger fixed to the movable cross

Jan 1, 1954

By M. J. Beus

This paper will describe the research approach being initiated by the Spokane Research Center to assess hazards and design criteria to prevent ground and muck falls in and around ore passes in hard-rock mines. The major goal of this research is to compile detailed information about ore pass processes and hazards, identification and testing of prevention strategies, and development of computer-based measurement and design methods. Recent ore pass failures have underlined the lack of OE pass design capabilities and standards available to both mine engineers and MSHA personnel. Design criteria and ore pass hang-up prevention and remediation strategies will include the effects of internal ore pass loads, blasting to relieve hang-ups, and rock mass stress redistribution and structural interaction from nearby mining. New visualization and three- dimensional analysis methods will be presented as an extension of existing ore pass design and analysis techniques. A sophisticated particle-flow analysis program will be used to simulate the response of various ore pass designs to a wide range of loading conditions driven by rock mass deformation, muck flow, ore pass blockage, and blasting in both nearby stopes and the ore pass. Analysis techniques will be calibrated and design criteria validated at the Spokane ore pass test facility. These tools will serve to reduce research costs by limiting the number of experimental field tests required.

Jan 1, 1996

By A. A. Angelov

This paper presents a unique method of monitoring the effectiveness of the planning process as well as the execution of mine plans. The method primarily determines the degree of deviation from the original mine plans by comparing actual mined areas to initially planned mining areas. The performance of mining operations is also measured by comparing actual and planned tonnages for a particular period. Once the degree of deviation from mine plans has been established the cause/s of the deviation can be determined through a simple fault tree analysis. Accurate identification of the reasons of deviation can aid the mine in selecting possible methods to correct the deviation. It is, however, beyond the scope of this paper to discuss the methods employed in correcting such deviations, as each mining operation will have unique causes of plan deviation and methods of remedying them. Deviations from the plan greatly affect the yields obtainable, which in turn affects the life of mine, thus having negative economic and financial implications. Accordingly, this paper presents a project management method which aims to reduce risk by improving planning systems to ensure optimum overall extraction of coal reserves.

Jan 1, 2010

By T. V. Philip, R. E. Lenhart

When commercial silicon iron sheets of varying magnetic quality are isothermally annealed at high temperatures, extremely large grains develop in the material having good magnetic properties. These grains are of the (110) [001] orientation and are formed by secondary recrystallization. The primary driving force for this secondary recrystallization is grain boundary free energy. For the secondary grains, activation energies of 103 kcal per mole for nucleation, and of 75.5 kcal per mole for growth, were obtained. The activation energy for nucleation of the secondary grains is consistent with a model involving redistribution of a precipitate acting as the primary grain growth inhibitor. SINGLY oriented silicon iron sheet was first produced in 1935.1 The material as commercially produced today has a very highly developed preferred orientation or texture; up to 95 pct of the grains are crystallographically oriented with their (110) planes in the plane of the sheet and their [loo] directions parallel to the rolling direction. This texture, usually written as (110) [00l], is referred to as the "GOSS" or the "cube-on-edge" texture. Because the magnetic properties of this material are superior to those of the nonoriented sheets in the direction of rolling, the oriented silicon iron has acquired tremendous industrial importance especially in the manufacture of transformer cores and other electrical equipment. The commercially produced material is essentially an iron-silicon alloy containing about 3 1/4 pct Si with minor impurities totaling less than 0.15 pct. The silicon steel heat is melted in the open hearth or electric furnace. The ingots are hot rolled, with or without being slabbed, to strips of 0.100 to 0.080 in. thickness. They are then cold reduced to an intermediate thickness, recrystallized, cold reduced to final thickness, decarburized, and finally annealed at a high temperature. During this high-temperature anneal, extremely large grains with the cube-on-edge texture are produced in the sheet. Several papers have appeared in the literature2-10 relating to the production of the Goss-textured material. Most of these describe the textures produced on cold rolling and on subsequent annealing of single crystal or polycrystalline silicon iron. May and Turnbull11,12 have recently shown the necessity of a second-phase dispersed impurity in the material for the production of the Goss texture. However, none of these papers describes in detail the nucleation and growth kinetics of the (110) [001] grains during the final high-temperature anneal.* The present work, therefore, is an attempt to understand the nucleation and growth kinetics of the cube-on-edge grains in the silicon iron sheet during the final high-temperature anneal.

Jan 1, 1962

By Ian J. Duckworth, Pierre F. X. Mousset-Jones

A detailed heat flow project was conducted at the Homestake Mine in Lead, South Dakota. This paper presents results obtained from a stope sensor system installed in the mine. The design and installation of the system are described in detail in a previous paper (Duckworth et al., 1992). The major project objective was the construction of a comprehensive heat flow data base to allow the design and testing of a new climate prediction model applicable to irregularly shaped underground excavations in non-homogeneous surrounding rock types. A mechanized cut-and-fill (MCF) stope contributes a substantial overall heat source in a mine, and the effect of this source on the working environment must be considered when planning future ventilation and refrigeration requirements. The relative magnitudes of the component heat sources encountered with the MCF mining technique are presented, having been computed from actual stope beat flow data collected over a one-month study period. The percentage of the overall heat load that is removed from the scope for each component heat sink is evaluated, and the overall energy balance is analyzed. A one-month study length was considered a sufficient period of time to allow stope monitoring for a complete range of mining conditions.

Jan 1, 1993

By W. R. Davison, C. A. Brown, J. P. Carstens

INTRODUCTION The phenomenon of heat-weakening of rock with 10.6 micron radiation from a continuous-wave C02 gas laser has been investigated in detail at the Massachusetts Institute of Technology for over 5 years. The programs at MIT have explored the basic nature of the heat-weakening phenomena and rock fracture caused by heating (e.g., Refs. 1 and 2), and have resulted in quantitative estimates of the relationship between the amount and parer level of heating and the resulting decrease in the modulus of rupture of a rock beam in a three-point bend test (Ref. 3). Results of the tests reported in Ref. 3 indicate a greater than 90% reduction in the modulus of rupture for granite beams heat-weakened by a laser. These results prompted the U. S. Department of Transportation to seek an assessment of the expected feasibility of employing the heat- weakening concept in a full-scale tunnel boring operation. Present- day continuous rock-tunneling machines have demonstrated tunneling time and cost savings over drill-and-blast methods, when used in rock types that are easily broken by the cutters. However, cutter bits have not yet been developed which can easily penetrate very hard rock

Jan 1, 1971

By A. W. Asman

The problem of balanced design in a belt conveyor has been under constant study. Increased use of this method of transport in recent years has stimulated investigations. Conveyor belt, power transmission and other machinery should be adequate to perform the required service. All components of the belt conveyor should work as an efficient unit moving its load continuously between terminals. As part of a long term research project on belt conveyors, Hewitt-Robins established in 1954 a 2-year grant at Pennsylvania State University. Under terms of the grant, certain fundamental phenomena were to be studied. This work evolved a new concept in belt conveyor power determination based on the principle of belt tension. The Penn State contract furnished the foundation for later more detailed studies. From these most recent investigations, more specific factors were defined. In the final analysis, all of the data collected has been worthwhile in belt conveyor design. Units now operate over long distances at speeds of over 800 fpm. Long high lifts are commonplace. Where vertical or inclined shafts were the rule, belt conveyors receive first consideration. Although belt conveyors have moved forward rapidly, the future will see a tremendous gain in their use. The ideal test belt conveyor would be several thousand feet in length and have a maximum tension of at least 70,000 lb., Also, this conveyor should be horizontai and have a variable feed rate of more than one material. Data from such a field belt conveyor combined with laboratory information would permit accurate analysis. Since this type of conveyor was not available, many field locations were visited: An alternate would have been to erect a closed circuit system in the laboratory. Either method had limitations and the first was selected as having the best possibilities. Manufacturers of conveyor belting and machinery basically have been using the same horsepower formula. As more information became available from field installations, factors in the basic formula were modified. Practically all conveyors are designed today by adding together the horsepowers required to move the empty belt, move the load horizontally, and elevate the load. In selecting size of drive motor, the first two elements are relatively unimportant if the last is large. However, it is the combination of

Jan 1, 1961

By David L. Rife

Introduction Our society is currently experiencing a change in civil philosophy toward US industrialization. We have become increasingly bent on the pursuit of a nirvanic state of zero risk. The money supply has become inversely proportional to its sources. And most mining companies, traditionally conservative, have become increasingly risk conscious. Rising taxes, high inflation, and decades of a steadily decreasing gross national product (GNP) - coincident with moral decay and disarmament - have eroded America's economic health. Psychology of US metal markets has shifted across the economic spectrum to disillusionment and discouragement. The sagging national economy, expanding governmental debt, and a backward mineral policy in concert with worldwide unrest and turmoil have caused great volatility in the metal markets. Congressional inaccessibility of US resources has contributed to its loss in strategic leadership and dependency on foreign suppliers and the common market. Large scale mining activities are now on the decline. And there is an overall slump in mineral exploration in this country. America now faces the sobering reality of almost total importation of 13 key mineral commodities and total dependence on foreign sources for five of them. There is a growing dependency on 21 of the 34 minerals vital to the US economy. And virtually everything needed can be imported directly from third world countries. Almost 85% of the free world's supply or production of vanadium, chromium, platinoids, manganese, and titanium - an essential to the aerospace industry - comes from South Africa. That country now plays a forefront position in supplying the West with minerals. The Soviets have become increasingly aware of this situation. They have made key moves in procuring for their own purposes major raw materials markets, particularly in South Africa. This is obviously threatening to the US' direction and brings about vulnerability to shortages and cutoffs. In spite of these developments and the overall change in the mining industry, there is good opportunity for growth ahead. The way has been paved for the smaller mining companies, particularly the more bullish of these. Smaller mining organizations possess a tight management and strong sense of direction. They can easily adapt to and cope with change. "Windows" that exist in the industry directly depend on a number of factors. These include the busi¬ness climate, market research and planning, management and human resources, applied appropriate technology, favorable hunting ground, and entrepreneurship. Mining as business Mining (and exploration) as a business is by its very nature highly speculative. It involves greater risk for a longer period of time than most other businesses. The entire mineral estate in the US continues to shrink. This is primarily because of various legislated wilderness measures. Consequently, the probability of finding an economic ore deposit in the US has decayed to less than 1%. Although the risk is high, the stakes far outweigh the gamble and are larger than most other businesses can offer. Mining properties, as investments or business opportunities, can provide effective hedges against long-term inflation because the real price for selected commodities, such as gold, may sometimes rise faster than inflation. Recessionary periods seem to provide the best climate for entering the mineral business or for a particular mining organization to expand its activities. Looking ahead and seizing opportunities during a depressed market will pay off. Property payments and royalties are likely to be lower. And the potential for an upward shift in prices for a given commodity is very positive. The decision to invest in a prom-

Jan 9, 1985

By Huber A. L

Research and development into alternate gold and precious metals adsorbents has resulted in the development of a new technology named the AUROSAVE adsorption process (ARGOSAVE'" for high silver con- tent ores). Adsorbents called VITROKELE'" can be tailored for either Gold I (cyanide leach) or Gold III (halide leach) applications. VITROKELE consists of a chemically synthetic adsorbent carried on an inert substrate, often a polystyrene bead. It is suitable for both in- pulp and in-solution use. VITROKELE adsorbent offers certain advan- tages over both carbon and ion exchange resin adsorbents. This paper describes testwork on Australian ores and commercial solu- tions obtained from operating Australian plants demonstrating the kinetic loading characteristics, elution methods and other operating parameters of VITROKELE adsorbent in the cyanide system. Brief reference is made to VITROKELE in the Gold III system.

Jan 1, 1988

By Alexander Sutulov

El presente trabajo señala el éxito de la mineralurgia latinoamericana en el aumento de producción durante la década del 60 a través de una estudio estadístico donde se muestra una alza productiva en un 88% de su valor y 60% de su producción física. Empero, este eventual progreso no coincidió con las exportaciones que se desarrollaron en el período señalado puesto que hubo un mayor consumo de minerales por las industrias nacionales y se eliminaron algunos productos latinoamericanos en los mercados internaciones, alcanzando solo un 20%. En esta perspectiva, es necesario que el desarrollo de la producción se mantenga al ritmo del consumo y la demanda en mercados internacionales ya que América Latina no dispone de sufiente capital como para financiar su desarrollo en niveles programados al tiempo y necesita un financiamiento exterior. Asimismo la década del 70 se convierte en un espacio de desafío puesto que Latinoamérica debe preservar los intereses nacionales, así como la atracción de capitales extranjeros en condiciones aceptables.

Nov 20, 1972

A comprehensive axial test program has been undertaken at the WASM Dynamic Test Facility on the performance of 20mm threadbar. The threadbar tests had a double embedment configuration, with variation to the encapsulation lengths, debonded length and surface hardware and fixtures to examine failure mechanisms. Performance was significantly affected by the collar embedment length and type of fixture nut used. Results ranged from thread shearing occurring between the nut and bar at 1kJ of energy dissipated, to control plastic deformation of a central debonded length dissipating 22kJ.

May 1, 2009

By E. A. Barnard

ARSENIC is a very old substance. The ancients speak of it in their writings, and its use has developed very little until recent years. The ancients used it in making pigments, in medicine, and for poison. They also tell of the difficulties of handling it-an experience which is very similar to our own. Until about 10 years ago, arsenic was very cheap and was a drug on the market. About that time the boll weevil began making serious inroads on the American cotton crops, and after much investigation the Depart-ment of Agriculture developed a very successful poison for this pest, consisting of calcium arsenate. The weevil pest has continued, and as the cotton planters have become convinced that calcium arsenate is the best material to use against the weevil, the demands for it have been steadily increasing, resulting not only in a rising price of arsenic but in a very serious shortage so far as our country is concerned. So serious has this shortage become, and so vital is it to the cotton growing industry, that Congress has appointed a committee to investigate and report on the situation. A meeting of arsenic producers and consumers was held in New York last December to take stock of the situation and to see what could be done. The extreme increase in, the market price of arsenic-from 6 c. to 15 c. per lb. in less than a year-has been very harmful to the producers as well as to the consumers. Some very interesting' data were brought out at this meeting, as follows: CONSUMPTION PER YEAR, SHORT TONS Arsenate of lead 2,000 Paris green 1,200 Proprietary mixtures 750 Sheep dips : 1,000 Weed killers 1,500 Glass : 2,000 8,450 1922 Consumption as calcium arsenate 4,000 12,450 1923 Estimated consumption as calcium arsenate... 12,000 Estimated 1923 consumption 20,450

Jan 8, 1923

By Launa Mallett, Charles Vaught, Michael Brnich, ROBERT PETERS

Interviews of 48 miners who escaped underground coal mine fires revealed that none of them had ever, before that incident, worn their self-contained self-rescuer (SCSR) either in training or in a real emergency. Consequently, they were ill-prepared to use this emergency breathing apparatus. One persistent problem stemmed from the fact that miners had no notion of breathing resistance, nor of the fact that it would get more difficult to breathe the longer they wore their device. As a result, many of those who were interviewed had simply removed their mouthpieces and breathed ambient air. This is obviously behavior that should be trained out of the workforce. Unfortunately, because of high costs and difficult logistics, miner training is unlikely to ever include donning and wearing an apparatus on a regular basis. In order to give workers a better idea of what to expect from their devices, therefore, the National Institute for Occupational Safety and Health researchers developed a tabletop (paper and pencil) simulation based upon actual predicaments evacuees had reported encountering. The simulation is designed to emphasize important points related to donning and wearing a self-contained self-rescuer in a mine fire escape, and, by doing so, to bring miners' expectations more in line with what their actual experiences would be. The simulation was field tested in six training classes at three different mining operations. In all, 99 individuals were involved in completing the exercise and rating its properties. In their ratings 88% of the respondents indicated they thought the scenario could definitely happen in real life, and over 80% agreed they had learned something new. From the field test data it was concluded that the simulation had authenticity and potential value as a teaching tool. The simulation was therefore used in a pre-test/post-test control group experiment to determine whether it led to improvements in miners' scores on a true-false test of their SCSR's functional capabilities and proper usage. Eighty-three miners were included in this part of the study. As expected, miners who had participated in the training exercise scored significantly higher on their post-test than miners who had not.

By Alan G. Galley

"Advances in our knowledge of the petrochemical attributes of deposit environments and of the character and extent of hydrothermal systems associated with certain deposit types has resulted in increased application of lithogeochemistry to exploration programs. Lithogeochemistry can be used to vector an exploration program toward an area of high potential through the use of a series of collapsing scales of analysis from a tectonic subprovince down to a particular stratigraphic segment. In the case of volcanogenic massive sulphide (VMS) deposits this involves the recognition ofsuitable volcanic domains, and the identification of subvolcanic intrusions and cogenetic felsic extrusive complexes. The recognition of chemical vectors within regional-scale alteration zones and associated chemical sedimentary rocks allows the geologist to identify the stratigraphic units with the most potential for hosting a base metal deposit.An integrated lithogeochemical program requires the judicious use of major, trace and rare-earth element and isotopic analysis. Standard discriminant plots may be employed to identify suitable tectonic and lithologic environments. Analysis of the chemical and mineralogical variations in broad-scale, semi-comfortable alteration zones provides a useful set of vectors to VMS mineralization. These may include contouring raw data, element ratios on XY plots, normalizing data against known rock values, or calculating mass changes in alteration zones."

Jan 1, 1995