Search Documents

By R Markoski, P Grealish

The requirement for rapid vertical development for underground ventilation is often a factor when dealing with dynamic mine plans, with short vertical developments being used to optimise ventilation systems. In an effort to increase the safety and efficiency of the constructions, a simple and effective sinking methodology is required that is both adaptable and repeatable. A modified shaft construction methodology is proposed that attempts to minimise risk to the personnel as well as be cost-effective. Readily available equipment is used to ensure adaptability to the various environments and shaft parameters.One of the greatest risks of shaft sinking is having personnel working suspended over open cavities or underneath suspended loads. Removing this risk, by ensuring all construction is done from solid ground, allows for safer sinking operations. As the process is repeatable, familiarity and confidence in its construction sequence will increase with each successive sink.A trial sink is performed with a 3.6 m diameter, 20 m deep shaft. The shaft was excavated using a conventional strip-and-line philosophy, with the shaft then being lined from the collar via the use of large diameter corrugated steel culverts. The annulus between the steel culverts and shaft excavation is then filled with a concrete mixture to secure it in position.The new process was successful, with no personnel at any time during the process being suspended above an open excavation. The installation had relatively low capital and operational costs and was completed faster than an equivalent, conventional concrete-lined shaft construction. Therefore when compared to conventional shaft-sinking methods, this process can be considered safer, more efficient and relatively cost-effective.Further research is required to determine whether this method can be expanded to larger vertical developments.CITATION:Markoski, R and Grealish, P, 2014. A new method for rapid vertical development of underground ventilation shafts, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 603–606 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S. Hodgson

Introduction The Red Dog zinc/lead deposit in northwest Alaska is the second largest zinc deposit ever discovered. Being developed by Cominco Alaska, with startup scheduled for early 1990, it will ultimately be the largest zinc mine in the Western World. Table 1 shows the reserves of the deposit. Bob Baker, a local bush pilot, discovered Red Dog in 1968. The US Geological Survey assessed the find. But the Red Dog site had been withdrawn from staking by provisions in the Alaska Native Claims Settlement Act of 1971 (ANCSA). Under the terms of ANCSA, the deposit was selected by the NANA Regional Corporation, one of 13 native corporations established by the Act. Then, in 1980, the US Congress confirmed this selection, in the Alaska National Interest Lands Conservation Act. In 1982, Cominco and NANA reached an agreement that has led to the development of the mine. Under the agreement, Cominco leases the property from NANA, develops and operates the mine, and markets the concentrate produced. In return, NANA receives royalties and, after capital recovery, participates in the net proceeds from the operation. The Alaska State Government is also playing a role in the development of the mine. Under the auspices of the Alaska Industrial Development Authority (AIDA), the state will construct, own, and operate the DeLong Mountains Regional Transportation System. This consists of a 84-km (52¬mile) road from the minesite to the Chukchi Sea. Located here are the port facilities necessary to store and ship the annual concentrate production and receive the mine fuel and supplies. For using this transportation system, Cominco will pay an annual toll fee. Over the anticipated 50 year life of the operation, the fee will provide a 6.5% return to the State of Alaska. In late 1986, Cominco's Board of Directors approved the Red Dog project. And, during the summer of 1987, road construction began. In February 1988, initial stripping began at the ore body and construction started at the millsite. Project setting The project site is approximately 1000 km (600 miles) northwest of Anchorage, 84 km (52 miles) east of tidewater on the Chukchi Sea, and 192 km (120 miles) north of the Arctic Circle (Fig. 1). The countryside consists of low, rolling hills that lead into mountains north and east of the deposit. The vegetation is typical tundra mat. And the site is in an area of permafrost. However, the permafrost is relatively warm and some areas have been found to be thawed. Examples would be creek bottoms and the site of the main waste dump.

Jan 12, 1988

Council for 2003/2004 President T.R. Stacey President-elect F. M. G. Egerton Vice-presidents Senior W. H. van Niekerk Junior R.P.H. Willis Immediate Past-president S.J. Ramokgopa Honorary Treasurer J.A. Cruise

Jan 1, 2004

By S. M. Rupprecht

"SynopsisThis paper is intended to document recent personal thoughts, opinions, and debate around the South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code) (2009) and its current usage by Competent Persons. Admittedly, some debates are as old as the SAMREC Code itself and have been ‘parked’ as no consensus could be reached by members of the SAMREC Working Group.Some of the more critical issues currently under examination are the definition of Competent Person and the potential registration of Competent Persons, the current re-write of the Code, and the introduction of reporting of Exploration Results, Mineral Resources, and Mineral Reserves on an ‘If not – why not’ basis, noncompliance with the Code and discipline, the role of the Johannesburg Stock Exchange Readers Panel, and the valuation of mineral assets based on scoping studies.IntroductionThis paper is intended as a personal memoir of recent thoughts and debate around the South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code) (2009) (‘the Code’). Admittedly, some debates, such as reporting of Mineral Reserves inclusive or exclusive of the Mineral Resource, are as old as the SAMREC Code itself and have been ‘parked’ as no consensus could be reached by members of the South African Mineral Resource Committee (SAMREC) Working Group. The author, who has been involved with the SAMREC Working Group since 2007, offers observations in his personal capacity as a professional mining engineer with the intent of getting practitioners to contemplate the influence of the Code on the mineral industry. Current practices in the compilation and reporting of Exploration Results, Mineral Resources, and Mineral Reserves are often deficient in adhering to the Code and a conscious effort must be made by the mining sector to improve the standard of public reporting, in particular Competent Person Reports (CPRs) and Public Reports issued by listed mineral exploration and mining companies."

Jan 1, 2015

By W. E. Hale, G. J. S. Govett

An orientation survey was conducted over a known disseminated copper deposit and a Au-Cu vein deposit and employed geological, geophysical, and geochemical methods. Geochemical techniques proved the most effective and economical means of locating and defining areas underlain by these types of mineralization. Six additional, widely separated occurrences were also investigated and mineralization was confirmed by determination of cold-extractable copper in stream sediments. The length of anomalous drainage varies from several to 16 km and depends on the type and tenor of mineralization. Despite generally marked relief and extreme physical and chemical weathering, cold-extractable copper anomalies in soils appear to reflect closely variations in the ore mineral content of immediately underlying rocks. Threshold values vary with local geological conditions and type and grade of mineralization. Significant thresholds in stream sediments are about 65 ppm and 10 ppm for cold-extractable copper in disseminated and vein copper occurrences respectively. Similar differences are encountered in soils. This necessitates the use of a scale of threshold values at progressive stages in each exploration program. Dis-seminated copper occurrences are presently the major source of mineral production m the Philippines. Much potentially productive ground remains to be investigated and applied geochemistry appears to offer the best available approach. The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Program (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature and involved both orientation and exploration. During approximately six weeks, an orientation survey, involving geological mapping, geophysical surveying and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Santo Nino (Fig. 1). This study demonstrated the economic and technical feasibility of geochemical ptospecting, relative to the other methods tested, for the location and delineation of a typical disseminated copper occurrence characteristic of those that represent the major source of metal in the Philippines.' Geochemical techniques, similar to those tested at Santo Nino, were then applied in a second orientation study of a vein occurrence at Suyoc (Fig. 1). The results of these two orientation studies suggest that, in reconnaissance work in this region, stream sediment analyses, combined with the determination of pH in the same streams, can be used to indicate areas underlain by rock containing anomalous concentrations of copper, whether it occurs in the large tonnage, low grade, disseminated deposits or in the comparatively small tonnage, higher grade, gold vein occurrences. Furthermore, the orientation surveys demonstrate that soil sampling and analysis serve effectively to outline more closely the mineralized zones within the generally anomalous areas identified from the stream reconnaissance. To further test the methods selected from the two earlier trials, six additional, widely separated prospects were investigated. The geological and geochem-

Jan 1, 1970

By K Aikawa, M Ito, K Mitsuhashi, Y Ebisu, J V. Satur, I Park, N Hiroyoshi, T Suto

Copper concentration using flotation is becoming more difficult, because of an increase in ore complexity accompanied by smaller grain sizes of copper minerals than usual, requiring finer grinding in order to liberate them. Project Arqueros, located at the mid northern part of Chile, is a copper mine project with an orebody consisting of various sulfides such as chalcopyrite, chalcocite, and bornite. Some of the copper minerals in Arqueros show low floatability mainly because of their fine grain size and resulted fine grinding size, and also because of the complex mineralogical composition. For example, chalcopyrite in Arqueros floats less than the other copper sulfide minerals. In this study we carried out some kinetic flotation tests with the Arqueros ore using a laboratory-scale forced air type flotation machine by varying the regrinding size. The products were assayed and mineralogically analysed to compare the minerals in their flotation behaviour with respect to size classes and liberation classes. The results were compared with a model calculation according to bubble size measurement. From the flotation testing and mineralogical analysis, it was found that copper minerals of the same size and liberation class floated at the same rate even with different regrinding size. At the same time the comparison between experiment and calculation showed that the fine particles of less than 5 µm size floated faster in actual than in the model applied. These results suggested that interactions among minerals of different species and of different sizes had positive impacts on the flotation rate of the fine particles. It indicates that this phenomenon can be applied to improve copper recovery in the project.

Aug 24, 2022

By Ross Glanville

The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR cam also be expressed as the Optimum Mime Life (OML) in years since the expected mime life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mime life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mime life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low¬-tonnage mines (such as many underground gold/silver deposits) often lead to sub¬optimal results. In fact, am apparently uneconomic deposit at am arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mime' properties based on arbitrary production rates.

Jan 1, 1984

"The application of telerobotics to mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa, and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place, a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run?A Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University to investigate these questions and many more through a series of experiments in a telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian College’s eDome. The laboratory supports many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments, and some preliminary results."

Jan 1, 2005

By R. L. Grayson

Conventional mine safety wisdom states that "the most efficient mines are also the safest." Since the 1980s, small mines (and contractors) have been targeted as the most dangerous ones because of their fatality records. Statistical testing of 1993 West Virginia safety and production data indicated that the most efficient WV mines were not the safest ones, considering correlations between the severity measure and tons per employee-hour, except for very small mines. This paper will present the results of an extended analysis of WV mine safety using 1993 and 1996 data, concluding with the method used to suggest current priorities for focusing interventions.

Jan 1, 1998

Conventionally, a combined system consist- ing of a dry or wet pulverizer and kneading mac- hine is applied to the pretreatment of fine mat- erials for agglomeration, especially for pellet- izing. However, treatment cannot be expected to be satisfactory owing to the complexities of the process. A new process was developed to over- come the defects inherent in the conventional process. This new process treats certain fine materials having a moisture content somewhat lower than that suitable for pelletizing in a ball or rod mill. The mill is of special de- sign in which grinding and strong kneading are performed to give an extremely homogeneous ball- ing material with appropriate size distribution and pelletizing characteristics. The most serious problem in this process is the choking of sticky materials in the mill. A specially designed rubber lining was installed in the mill to overcome this trouble. This paper presents actual results from our iron ore pelletizing plant relating to the pelletization of other fine materials.

Jan 1, 1974

By Ernt. W. D.

A membrane based mixed extractant process was developed for selective removal of copper from waste acidic cupric chloride etchant solutions found in printed wire board manufacturing. The process uses a mixture of Adogen 381 (tri-isooctylamine), MOC®-45 (ketoxime) and MOC® 55TD (aldoxime) in a kerosene diluent. The mixed extractants recover the copper from a hydrochloric acid medium and transfers it to a sulfuric acid medium. The process also utilizes unique wetted membranes to separate the aqueous and organic phases. The driving force for these membranes is not pressure but the difference in surface tension between the two phases. By using these membranes, complete phase separation results. There is no physical entrainment contamination as found in conventional systems. The only cross contamination is the solubility concentration of one phase in the other. This however is less than 10 mg/l.

Jan 1, 1998

By Bagley A. S

The accuracy and precision of rutile analyses are discussed. Comparison is made between the wet chemical and X-ray fluorescence spectrographic methods of. estimating Ti02 in commercial rutile. Various allotropes of 'I'i02 are identified by diffractometry and a comparative analysis of the coloured varieties of rutile is given. For X-ray fiuorescence . analysis, specimen preparation is critical and sample grinding and pressures. for pellet making are discussed in detail.Cellulose bonded and backed pellets are shown to be subject to relaxation with increasing age.INTRODUCTIONTo date much of the analytical work on commercial samples has been done by wet chemical methods.This led to various discrepancies in results, which are of particular importance when certificates must be issued for overseas shipments. The present work reviews the nature of rutile and compares the results of Ti02 estimation by wet chemical methods and those obtained by X-ray fluorescence spectrographic analysis.In the rutile industry the results from different analysts and even those from the same analyst are not always consistent. To the analytical chemist this should not be surprising.Fairbairn (1951) showed the results obtained from 34 different analysts on a specially prepared sample of granitic rock. It is of some interest to note that the Ti02 content as determined by the 34 analysts using unspecified methods ranged from 0-17 per cent to 0·30 per cent. Fairbairn (1953) found that1. replicate analyses from the same analyst give a high order of precision,2. analyses by different analysts using the same procedures give reasonable precision, and...

Jan 1, 1965

By Christopher Snee

??care has to be taken that the design is driven by sound geological reasoning and rigorous engineering logic rather than by the very attractive images that appear on the computer screen.??Hoek 1999 Design of a cavern is inextricably linked to the engineering geology of the site. The importance of sound geological reasoning will be illustrated by transportation projects in New York City where there are proposals for at least 11 caverns. These caverns have been the subject of advanced exploration techniques and geological interpretation but even so the raw data falls short of the sophistication of modern numerical methods. This paper will give geological explanations for the engineering characteristics of the rock in New York City which will provide guidance for practitioners when approaching cavern design in New York and elsewhere.

Jan 1, 2008

By N. L. Wimmler

The Metaline mining district was examined in 1942 by Bureau of Mines engineers with the cooperation of geologists of the Federal Geological Survey. Because the demands of war production were rapidly depleting reserves in some of the older zinc-lead producing districts of the United States, it was decided that an attempt should be made to increase the proved or indicated ore reserves of the Metaline district. With this objective, certain areas to be explored by diamond drilling were selected. The Bureau of Mines began work on this program. January 15, 1943; work terminated September 8, 1945. Forty-five holes were drilled in seven areas, The holes ranged from 154 feet to 2,050 feet in length. Their combined length was 38,150 feet. Thirty-three of the holes were drilled in. the North Pend Oreille and the West Bella May areas.

Jan 1, 1949

By D. Racicot, T. Hanel, E. H. Chown

Over thirty plutons in the Chibougamau-Desmaraisville belt were examined briefly in the field and sampled, in addition to the few masses that have been studied in detail. The survey indicates that the intrusions may be conveniently grouped in four main categories, based on their time of intrusion. These are; remobilized basement domes, pre-kinematic intrusions, syn-kinematic intrusions and postkinematic intrusions. Basement domes, as exemplified by the Lappa rent Massif, are composed of migmatized tonalite-diorite gneiss that has undergone at least two periods of mafic dyke intrusion and at least three major deformational periods. The rise of the basement domes was accompanied by extensive mylonitization and the intrusion of syn-tectonic plutons. Pre-kinematic plutons, such the Chibougamau pluton, are diori te-tonalite in composition, and were intruded into the supracrustal pile and partly eroded before the main deformation of the belt. Syn-kinematic plutons occur principally as marginal intrusions bordering the belt (Barlow), or as discrete intrusions along structural highs (La Dauversiere), and are either hornblende monzodiorite or tonalite in composition. Post-kinematic plutons, such as Muscocho, are principally granodiorite and often porphyritic intrusions locally deforming the enclosing rocks. The close relationship between mineralization and high-level intrusions such as the pre-kinematic and some of the post-kinematic plutons is discussed.

Jan 1, 1984

By Alan L. Sangster

Abstract -Auriferous, bedding-parallel veins occur in zones of carbonaceous, argillaceous and sulfidic turbidites in the Lower to Middle Cambrian sandy flysch of the Goldenville Formation. The ?34S values for vein and wall-rock arsenopyrite and pyrrhotite, and for regional pyrite and pyrrhotite, are highly positive. The values are similar to those from Cambro-Ordovician sediment-hosted deposits of other types, and display trends that increase upward in the stratigraphic sequence. The similarity in composition of vein and wallrock sulfides indicates a seawater-sulfate source for sulfur, derived from the enclosing rocks at the time of vein formation. The upward increase in ?34S values is consistent with closed system sulfate reduction in the anoxic portion of a stratified water-column. Published ?18C and ?18O values for Meguma Group vein carbonates are unlike those of other gold-vein carbonates, but are similar to those of diagenetic-metamorphic carbonates from the Meguma Group and elsewhere. These data indicate that the source for the vein-related sulfides and carbonates may be the host strata; possibly the arsenic and gold were derived from the same source.

Jan 1, 1992

By Charles W. Huggins

A study of the high magnification of some inorganic fibers which are found in nature or produced in the laboratory, has been conducted with the electron microscope. This series of electron microqraphs shows the important morphological differences exhibited by potassium-lead silicate, lead-aluminum silicate, chrysotile, wollastonite, silicon nitride, potassium titanate, cobalt chrysotile, magnesio-fluor-richterite, fluor-richterite, refractory oxide fiber, silicon carbide, massive serpentine, and palygorskite. A ribbon or a thin lath 250-2500 A. wide is the structural form of potassium-lead silicate and lead-aluminum silicate. Chrysotile, cobalt chrysotile, and massive serpentine all have a tubular structure and a fairly uniform (150-300 A.) diameter. Wollastonite, potassium titanate, fluor-richterite, and magnesio-richterite crystals have a lath shape, and potassium titanate laths are laminated ribbons. Single fibers of silicon nitride and palygorskite are ribbons, and the silicon nitride sample contains many twins (branching fibers). Palyqorskite fibers are highly flexible and have cross-sectional measurements of 150-300 A. Silicon carbide fibers differ from other fibers because their structure consists of several different forms. The sample used in this study had, predominately, a margarite-type structure. The refractory oxide fiber lost, all its apparent fibrosity after being prepared for electron microscopic examination, and only irregular fragments are visible in the electron micrographs.

Jan 1, 1962

By Shuangsuo Yang

Based on field observations and physical modeling of simulated materials, the dynamic equilibrium principle on the whole interaction process between the surrounding rocks and support of large deformation roadways in coal mines has been developed. It explains the methods of forming the bolted strata and its changing load capacity with deformation. It also points out the factors and conditions for forming the bolted strata as follows: (1) many entries in coal mines are subject to large deformation. During their service life, it goes through the following process, elastic > plastic > fiacture > broken > loosening, etc. During this dynamic process, the mechanisms of supporting structure are changing and therefore the interaction between support and rocks experiences a process of dynamic equilibrium. Furthermore, the required supporting force for stabilizing the surrounding rocks shows overall decreasing trend; (2) the bolted strata is a special supporting structure consisting of bolt, rock skin protection devices and rock strata within the bolted horizon. As deformation increases, the supporting structure of the broken strata within the bolted horizon experiences a process of periodic change, from equilibrium > not equilibrium > equilibrium. Corresponding to this change, the supporting capacity of the bolted strata also fluctuates and gradually decreases; (3) under the bolted strata, the stability of a large deformation roadway is dynamic and step-wise; and (4) the formation of bolted strata, especially bolted broken strata depends on the existence of compressive force. Supporting the bolted strata is not constrained by the quality of the surrounding rocks. It has broad range of application.

Jan 1, 2005

By C. C. White

Although many notable scientific investigations relating to roof control have been made, roof control still must be considered one of the more baffling problems confronting the miner. Each year contributions are made to our understanding and techniques in dealing with various single phases of the overall problem, however, an equation considering all the variables involved in roof control, if formulated, would indeed be hopelessly complex. Among the factors to be considered is first, gravity which is always acting but which is sometimes less of a problem than lateral forces. There are lateral forces due to expansion, resulting from the weight of overlying rock; to these must be added lateral stresses of orogenic or tectonic orgin, which may be enormous. Stresses due to plastic flow of beds, water pressure, gas pressure, expansion due to absorption of water, faults, joints, fractures, pot heads, and the like may complicate the solution. Therefore, we must base decisions on roof control, and roof bolting in particular, largely on experience, and far too often on few "knowns" and many "unknowns", The development of "in situ" roof trusses may prove of benefit because, they unlike roof bolting, promise positive calculable roof support. These trusses require installation of steel tensioned rods in the roof, which rods are arranged to produce a stress pattern similar to a bridge truss, the roof rock acting to transmit the compression forces. The simplest form of truss (see figure 1) consists merely of two steel rods anchored at the back of holes drilled at an angle of approximately 45° over the pillars, collared near the the middle of the room, the lower ends of the rods being connected together by tierods and turnbuckles. Used in this way, a 3/4" diameter rod can offer greater support than a 10" x 5-3/4" wide flange steel beam. By tightening the turnbuckle, uplist on the roof can be produced,, the downward reaction being transmitted to the pillars by the rods. This simplest form of truss has been used in rooms up to 24' in width. Trusses of four panels, that is, consisting of a truss within a truss, as shown in figure 2, have been used successfully in rooms 30' wide. (figs 2 & 3) It appears a 6 panel truss could be used in a 40, wide room.

Jan 1, 1968

By W. C. Winegard, W. J. Bratina

Internal friction characteristics and temperature dependence of the torsion modulus for iodide zirconium containing 2.4 pct Hf were investigated, using a low frequency pendulum technique. The internal friction curve consists of a background which increases as the temperature increases, a maximum at 860°C apparently a background due to the al-lotropic transformation, a maximum due to grain boundary relaxation with an associated heat of activation of 58,000 cal per mol, and an anomaly below 350°C which may be associated with a precipitation perphenomenon, Oxygen in below small amounts reduces the grain boundary maximum substantially. The variation of the torsion modulus at 20°C was found to be 3450 Kg per mm2 for the zirconium used in the present work. IT is well known that small amounts of certain solutes materially affect the ductility of zirconium. Lely and Hamburger,&apos; as early as 1914, found that high purity zirconium exhibited a remarkable ductility, while Fast&apos; has shown that oxygen and nitrogen can cause substantia1 embrittlement. Treco" has recently demonstrated that the ductility decreases sharply with the oxygen content, and that 2 atomic pct O2 embrittles zirconium to such an extent that cold working is impossible. The marked decrease in ductility is difficult to understand in view of the fact that Domagala and McPherson4 report the solid solubility of oxygen in zirconium to be 29 atomic pct at 500 °C. Another metal which behaves much the same as zirconium in this respect is titanium. Pratt et al." investigated the internal friction characteristics of titanium and the effect of oxygen on the internal friction values. It is evident that internal friction measurements are of value for studying grain boundary segregation, as shown by Pratt et al. for oxygen in titanium, by Pearson for oxygen in copper, and by Maringer and Schwope for oxygen in molybdenum. With this in view, the internal friction characteristics of zirconium and the qualitative effect of oxygen on the grain boundary relaxation phenomenon were investigated. Materials and Experimental Procedure The zirconium used in the present work was supplied by the Foote Mineral Co. in the form of wire 0.05 in. diam. The analysis supplied by the manufacturer indicates the amount of hafnium as 2.4 pct, less than 0.01 pct O less than 0.01 pct N,, less than 0.02 pct H,, and less than 0.001 pct C. Additional spectro-graphic analysis indicates the other main impurities as follows: 0.01 pct Fe, 0.05 pct Si, 0.008 pct Cu, <0.005 pct W, <0.001 pct Al, <0.05 pct Mg, <0.001 pct Ni, <0.02 pct Ca, and <0.01 pct Ti. Microscopic examination of the material in the as received condition revealed very fine grains with numerous twins. Specimens were annealed either in situ in the internal friction apparatus or in evacuated silica tubes in an auxiliary furnace. When the specimens were annealed in the auxiliary furnace, they were wrapped in identical zirconium wire to prevent contamination by the container. Metallographic sections were taken in all cases. Some were taken from the specimens used for internal friction measurements after completion of the experiments, while others were taken from control specimens at intermediate stages of the experiments. lnternal friction values were obtained by measuring the free decay of a low frequency torsion pendulum (1 cycle per sec), the suspension of which was

Jan 1, 1957