Search Documents

By D F. S Natusch, R J. Hooper

Recent lignite investigations indicate their potential as a strategic long-term fuel resource. This potential however would be determined not only by lignite quantity and quality, but also by economic, physical and social resources required to support it. The following discussion uses the example of a typical lignite mining operation to review the major resource requirements. While recognising that the implications of supplying those resources may be as important as their actual existence, this paper has purposely omitted such discussion as this will be one of the main target areas for the next phase of investigations.

Jan 1, 1983

By M. M. Poulton

Universities are not immune from the large number of retirements facing the mining industry. Department heads anticipate that we will need to replace all of the senior mining engineering faculty in the U.S. by 2020. Long term studies of Ph.D. completion times and success rates indicate that in Engineering disciplines in the U.S., the ten year completion rate is 65% at best and the four year completion rate is less than 8%. We do not have accurate data on completion rates and times for mining or metallurgical engineering Ph.D. students in the U.S. but students self-report their expected completion times are around 4 years. National data on doctoral students indicate that younger, full time students with sufficient financial support have a higher probability of success in completing their degrees in a timely manner. Students in Eastern U.S. mining engineering programs are on average 32 years old, 85% are full time, and the gap between support and cost of attendance is $5,000 per year. Students in Western U.S. programs are on average 38 years old, 78% are full time, and the financial gap is $8,483. Further, it appears that domestic graduate students are not very geographically mobile. The current demand for new faculty is higher in Western programs but the longer term retirements are higher in Eastern programs. While all Ph.D. students who responded to the 2010 survey indicated an interest in a faculty position at some point in their careers, very few were applying for the open positions. Over the past 35 years for which data could be obtained, the maximum number of Ph.D. students enrolled in mining engineering in the U.S. is 115 with a maximum of 27 degrees granted in one year. On average 89 students are enrolled in doctoral programs in mining engineering in the U.S. with average degree production of 15 Ph.D.s per year.

Jan 1, 2012

By Marcela Aliaga

Este trabajo propone una metodología para disponibilizar un mapa de calor de riesgos de conflictos sociales, que sirva como instrumento de alerta temprana y de gestión preventiva, pero que también permita comprender cuáles son los factores concomitantes que inciden en la mayor probabilidad de ocurrencia de conflictos sociales vinculados tanto con las prácticas empresariales como con las condiciones socioeconómicas y culturales del contexto. Para elaborar este mapa de calor, se ha construido un índice de riesgo de conflicto social que incorpora 13 variables (7 internas o vinculadas con el desempeño de la empresa y 6 externas o de contexto).

Sep 29, 2023

By M. A. Reyes, L. Yan

"Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 hours while maintaining an apparent temperature (AT) below 95°F (35°C). NIOSH tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in NIOSH underground coal mine facilities to investigate the thermal environment over a 96-hour period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners increased over the 96-hour test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating heat and humidity temperature profiles for RAs not tested in situ. INTRODUCTION RAs are designed to provide a life-sustaining environment for miners who cannot escape after a mine disaster. One of the major considerations for integrating RAs in mine environments is the thermal environment inside the RA and the impact that the surrounding mine conditions have on the temperature and humidity buildup. Previous research has observed that the metabolic heat of the occupants and the heat released by the CO2 scrubbing systems will cause the RA interior air temperature to increase. In addition to the increase in temperature, an occupant’s respiration and perspiration, as well as the chemical reaction of the scrubbing chemicals with CO2, will contribute to an increase in humidity within the RA. The resulting internal thermal conditions, if not controlled, can subject miners to conditions that can lead to heat exhaustion, heat stroke, or even death depending on the duration and magnitude of exposure. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Mine Safety and Health Administration (MSHA) regulations require that RAs must be designed to ensure that the internal AT does not exceed 95°F (35°C) when the RA is fully occupied."

Jan 1, 2018

By Horace C. Porter

Most of the bituminous and semibituminous coals of this country will coke, and all of them yield, on carbonizing, more or less marketable gas and byproducts. We need, however, a finer distinction as between various grades of coking coals and between coals of different degrees of byproduct and gas-making possibilities. There is required by the consumer or the coal producer a dependable test to show whether a certain coal or mixture of coals will make coke of good commercial value for blast-furnace, foundry, water-gas, or domestic use; whether any difficulties in operation may arise from properties inherent in the coal; and whether gas and byproducts may be expected of good quality and in profitable quantity. For determining coke quality, the most dependable test is an actual run in an oven, but for byproducts a coal may better and more accurately be tested in the laboratory or in a miniature oven or retort. As to what are the most desirable qualities in blast-furnace coke, the furnace men themselves are not in complete agreement. Some desire a hard, well-burned, "hot" coke, and others get better results from a llgreener," less hardened product that burns somewhat more readily in the furnace. But certain qualities of cell structure and porosity are commonly agreed upon as desirable. Information as to what kind of coke a certain coal may be made to yield is valuable in advance, whatever may be the consumer's ideas as to the particular kind most suitable to his needs. The question arises, Can we predict coking quality with any degree of satisfaction from a small-scale test? It used to be said that coals could not be tested satisfactorily on a laboratory scale either for the coke they would yield or the byproducts. On account of the mystery with which the coking quality of coal has been shrouded and the large determining influences that many believe are exerted by mass, pressure, and the passage of carbonaceous volatile matter through the coking material, it has seemed difficult to reproduce in the laboratory the exact conditions of commercial practice. Great progress, however, has been made in recent years in elucidating the process of carbonization and many of the factors that make for the formation of high-grade coke and the recovery of the best

Jan 1, 1920

By H. Kazemi, G. W. Thomas, M. S. Seth

The double-porosity model of Warren and Root7 for examining pressure drawdown and buildup phenomena in naturally fractured reservoirs has been extended to intetpret interference test results. Both analytical and numerical solutions are presented. The practicality of some of the assumptions in the Warren-Root model was also investigated. The standard procedure for interpreting interference tests in naturally fractured reservoirs beretofore employed an equivalent homogeneous reservoir model. A comparison of our results with the equivalent homogeneous model indicates the latter is inadequate for early time responses. For late time responses, however, the simpler equivalent homogeneous model yields favorable results. Finally, the effects of well spacing and the magnitude of the interporosity flow parameter are briefly cited. INTRODUCTION Interference tests can be used to provide reservoir information not obtainable from conventional pressure drawdown and buildup tests. The technique involves measuring the response in one or more wells arising from a pressure perturbation introduced into another well. It has been. successfully applied to single-layer, homogeneous, unfractured, isotropic and anisotropic formations to arrive at values of well storage capacity and a measure of directional permeability.l The techniques of interference testing usually can be extended to heterogeneous systems, provided the permeability contrast between any existing rock layers is not excessive.9 In such cases, the practical interference effects in an observation well of an interconnecting heterogeneous reservoir can be predicted using an equivalent homogeneous model. The calculated properties are then average values. Russell and Prats2 have demonstrated the utility of this approach for a single-phase, two-layer system. For naturally fractured reservoirs, some different approaches usually are necessary. The major departure from homogeneous or nearly homogeneous reservoir treatment is to characterize the fractured system as an entity having "double-porosity"; namely, we suppose the existence of both primary and secondary porosity, where the former is contained within a systematic array of identical rectangular matrix blocks and the latter is contained within an orthogonal system of continuous, uniform fractures (see Fig. 1). It is sufficient to assume that the permeability of the rock matrix is so small that movement of reservoir fluids to the producing wells is entirely through the fracture network. This assumption has been validated by Barenblatt3 and .employed by others?-7 Warren and Root7 used the double-porosity model to develop an interpretation of pressure drawdown and pressure buildup tests in naturally fractured

Jan 1, 1970

By M. K. Kim

This study presents a framework for quality inspection of precast concrete components using the 3D laser scanning technique. As precast concrete-based rapid bridge construction is getting standardized, quality assessment of the precast concrete becomes critical for preventing any failures during the construction process. Moreover, as Building Information Modeling (BIM) gains popularity in the construction industry, autonomous and intelligent inspection systems are needed. Current method for quality control of precast concrete components, however, heavily relies on visual inspection and contacttype measurements, which are time and labor demanding. Also, storage and delivery systems of inspection information such as the procedures and results of quality inspection are lacking. To overcome these limitations of the current quality assessment technique for precast concrete, this study aims to develop a BIM-based framework for efficient quality inspection of precast concrete with the use of a 3D laser scanner. First, we formulate practical guidelines including detailed inspection procedure, selection of optimized scanner and scan location, inspection criteria, and data storage and delivery system. Second, to investigate the applicability of 3D laser scanning to precast concrete quality inspection based on the proposed framework, a case study inspecting quality of a lab-scale object assumed as precast concrete component is presented for detecting defects.

Aug 1, 2013

By Charles L. Thomas

A novel, highly sensitive, and reproducible nzetlzod for the determination of hydrogen in solid materials is presented. The procedure requires equilibration of the specimen with hydrogen gas, rapid quenching, and hot vacuum extraction of the dissolved gas with subse-quent quantitative analysis by mass spectroscopy. Good linearity is obtained for the Arrl~enius plots of the investigated metals. The advantages in the use of this method over that of Sieverts aye discussed. The solubility data for copper are in reasonable agveewzent with a considerable number of other inuestigations, wllile those fov silver are considerably lower than previously reported. The first known solubility data for gold are presented. Solubility equations and heats of MUCH of the data which are available on the solubility of hydrogen in various metals and alloys have been obtained by the classical Sieverts method.' The method involves the measurement of a decrease in pressure of a gas in a calibrated system, and the calculated contraction in volume is attributed to the solubility of the gas in the metal sample. The procedure requires several corrections, such as the solubility of the gas in the container walls and the diffusion of the gas through these walls, as noted by Steacie and .Johnson2 and others. In addition, errors may be incurred due to reactions between metal surface impurities, such as oxides, and the saturating gas. The precise calibration of the measuring system where large thermal gradients exist can present additional difficulties. Also, accurate volumetric measurements of small quantities of gas are difficult. Many of the objections to the Sieverts method were overcome on solid materials by Ransley and ~eufeld,~ who first saturated the metal with hydrogen and performed a subsequent extraction and measurement of the gas by chemical means. Eichenauer and pebler4 and Eichenauer, Kiinzig, and pebler5 measured the diffusion coefficient and solubility by following the degasification of a sample as a function of a rate of increase in pressure in a previously evacuated system. Here again, however, the procedure involves many of the corrections of the Sie-verts method. The present investigation deals with the solubility of hydrogen in solid copper, silver, and gold by a technique which eliminates many of the aforementioned corrections and possible errors. This procedure requires equilibration of the specimen with gas, rapid quenching, and hot vacuum extraction of the dissolved gas with subsequent quantitative analysis by mass spectroscopy. EXPERIMENTAL Two completely separate systems were employed to accomplish first, the equilibrium saturation of the sample and second, the extraction of the dissolved gas. Saturation Apparatus. The saturation apparatus, illustrated in Fig. l, consisted of a vertically mounted quartz tube with a three-way valve for vacuum or hydrogen near the top and an outlet near the bottom leading to a butyl phthalate seal. The bottom end of the tube was terminated with a joint accommodating an O-ring sealed "Asco Stirring Gland" (The Emil Greiner Co.). This gland facilitated movement of the thermocouple without introduction of air into the system. The upper portion of the tube (above the furnace) was water-jacketed. A Welsh 1405-B mechanical pump provided the necessary system evacu-

Jan 1, 1968

By E T. Baker, J A. Resing, S L. Walker, V Ferrini, F Martinez, R Haymon

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Enumerating active sea floor hydrothermal sites has been a challenge since their discovery almost 40 years ago. High-temperature hydrothermal sites are readily discoverable, primarily by detecting mineral-laden plumes, but working at these sites poses severe environmental and operational difficulties. Low-temperature vent fields, which may represent waning of venting from high-temperature systems, may be more accessible but are more difficult to locate. Over the last decade, however, oxidation-reduction potential (ORP; aka Eh) sensors capable of detecting minute concentrations of reduced hydrothermal chemicals have been successfully used to pinpoint such fields. In this extended abstract, we use ORP anomalies observed during continuous (towed sensor) plume surveys to estimate site frequency along four intermediate- to fast-spreading ridge sections. From these data, we estimate site frequencies between five and 16/100 km for these ridge sections. Previous camera surveys on the fast-spreading East Pacific Rise support these frequencies. These rates are much greater than the frequency of ~0.5–5/100 km, generally increasing with spreading rate, derived from well-surveyed ridge sections in the InterRidge database (InterRidge, 2014). The higher frequencies arise because ORP sensors are able to distinguish between sites as close as ~1 km and identify sites with negligible or no optical plume signal.CITATION:Baker, E T, Resing, J A, Martinez, F, Haymon, R, Walker, S L and Ferrini, V, 2015. How leaky are oceanic ridge axes? A new assessment of the spatial density of submarine hydrothermal discharge, in Proceedings PACRIM 2015 Congress, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Brij M. Moudgil

Separation of oil shale from waste material or into high grade and low grade fractions can have a major influence on the economics of the surface (ex-situ) retorting process. Different components of shale rock vary significantly in physical and surface chemical properties such as specific gravity, color, water wettability etc. Various techniques which utilize the difference in one or more of the above propartis have been proposed to preconcentrate the oil shale before retorting. A discussion of the techniques proposed such as gravity separation, sorting and froth flotation is presented.

Jan 1, 1982

By E. N. Skinner, Arthur Philliops

During the course of an experimental program concerned with the hydrogen embrittlement of copper containing oxygen in concentrations within the solubility limits it became necessary to make a critical appraisal of the literature dealing with the solubility relationships of oxygen and solid copper. The latest determinations, and perhaps the only data obtained on "spectroscopically" pure copper, are those of Rhines and Mathewson' who reported that the solid solubility increases from 0.007 per cent oxygen at 600°C. to about 0.01; per cent at 1500ºC. Hanson, Marryat and Ford2 had previously placed the solubility limit at less than 0.009 per cent oxygen at 1000ºC. and Allen and Street3 had suggested, on the basis of an unpublished research by T. Hemitt, not over 0.005 per cent oxygen at 500°C. In the introductory stages of the investigation indirect evidence accumulated to suggest that the solubility limits were significantly lower than those previously reported. For this reason it was deemed essential to clarify this point before proceeding with a program intended to establish a quantitative relationship between hydrogen embrittlement and oxygen concentrations positively known to be within the solid solution range. Furthermore, the increasing production and the highly selective applications of the commercial "oxygen-free" coppers inevitably direct attention to the practical necessity for exact knowledge regarding the effects of mini-tie concentrations of the elements ordinarily found in the high-purity coppers now available. Of these elements oxygen occupies a unique position, not only by virtue of its specific effects on copper but more particularly in view of its important reactive tendencies toward the other impurities with which it is associated. Rhines and Mathewson considered several methods for measuring the solubility of oxygen and finally adopted the simple plan of saturating the specimens, obtained from redeposited cathode copper, by heating at the desired temperature in air. After the removal of surface oxide by mechanical and chemical means, the oxygen content was determined in the underlying metal. In general, this process of saturation, with a few modifications, was followed by the present writers. Although the procedure is direct and has obvious advantages, its effectiveness, unfortunately, is reduced by an excessive scaling of the copper, particularly at the higher temperatures. After saturation treatments above 900°C. the writers found that the specimens, necessarily rather thin in the original condition, consisted largely of scale and yielded too little metal for a satisfactory analytical sample. Furthermore, great difficulty was experienced in effecting complete removal of the scale. Needless to say, it is necessary to exercise extraordinary care in the preparation of the surface of the analytical sample in order to eliminate submicro-scopic fragments of cuprous oxide which ordinarily are lodged in the crevasses and

Jan 1, 1941

By E. N. Skinner, Arthur Philliops

During the course of an experimental program concerned with the hydrogen embrittlement of copper containing oxygen in concentrations within the solubility limits it became necessary to make a critical appraisal of the literature dealing with the solubility relationships of oxygen and solid copper. The latest determinations, and perhaps the only data obtained on "spectroscopically" pure copper, are those of Rhines and Mathewson' who reported that the solid solubility increases from 0.007 per cent oxygen at 600°C. to about 0.01; per cent at 1500ºC. Hanson, Marryat and Ford2 had previously placed the solubility limit at less than 0.009 per cent oxygen at 1000ºC. and Allen and Street3 had suggested, on the basis of an unpublished research by T. Hemitt, not over 0.005 per cent oxygen at 500°C. In the introductory stages of the investigation indirect evidence accumulated to suggest that the solubility limits were significantly lower than those previously reported. For this reason it was deemed essential to clarify this point before proceeding with a program intended to establish a quantitative relationship between hydrogen embrittlement and oxygen concentrations positively known to be within the solid solution range. Furthermore, the increasing production and the highly selective applications of the commercial "oxygen-free" coppers inevitably direct attention to the practical necessity for exact knowledge regarding the effects of mini-tie concentrations of the elements ordinarily found in the high-purity coppers now available. Of these elements oxygen occupies a unique position, not only by virtue of its specific effects on copper but more particularly in view of its important reactive tendencies toward the other impurities with which it is associated. Rhines and Mathewson considered several methods for measuring the solubility of oxygen and finally adopted the simple plan of saturating the specimens, obtained from redeposited cathode copper, by heating at the desired temperature in air. After the removal of surface oxide by mechanical and chemical means, the oxygen content was determined in the underlying metal. In general, this process of saturation, with a few modifications, was followed by the present writers. Although the procedure is direct and has obvious advantages, its effectiveness, unfortunately, is reduced by an excessive scaling of the copper, particularly at the higher temperatures. After saturation treatments above 900°C. the writers found that the specimens, necessarily rather thin in the original condition, consisted largely of scale and yielded too little metal for a satisfactory analytical sample. Furthermore, great difficulty was experienced in effecting complete removal of the scale. Needless to say, it is necessary to exercise extraordinary care in the preparation of the surface of the analytical sample in order to eliminate submicro-scopic fragments of cuprous oxide which ordinarily are lodged in the crevasses and

Jan 1, 1941

By N. B. Pundari

Proper selection of large walking draglines, based on sound engineering principles and field experience, has not kept pace with the large capital expenditures needed to buy these stripping machines. The use of large walking draglines for stripping overburden in US surface coal mines grows steadily, but equipment selection continues to pose problems. An improper size, model, make, or spoil reach selected for a particular stripping application results in additional, unnecessary coal production costs. Large walking draglines are being used to dig deeper tar sands at the Syncrude operations near Fort McMurray in Northern Alberta, Canada. This application is compared with typical deep digging operations and dragline use prevalent at typical US strip mines.

Jan 4, 1981

By G. K. Manning, A. R. Elsea, A. B. Westerman

A considerable number of high-tem-perature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. .4t the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in vitalliurn after various heat treatments. Howcver, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chro-mium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja and Guertler2 indicated that cobalt and chro-mium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to 85 pct chromium undergo a transformation at [zoo to 12 50 c More recently, Wever and Haschimoto,3 Wever andLange,4and Matsunaga5 carried Out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallogra~hic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Mat-SUnaRa. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these excep-tions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data arid the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitalhum by deter-mining the diagram for the cobalt-chro-mi~m system- Experimental Work For the convenience Of the reader, the diagram as determined by the present investigation is presented in Fig 3. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the melting point for pure chromium is the

Jan 1, 1949

By Ed Coulter

Nevada has a population of 1.2 million people of which only 21% or 312,rIXl are native born Nevadans. he population between 1980-1990 grew a record of 389%. and ls the fastest growing state in the union. While only 2.5% of the total population are direct employees of the mining industry, excluding Reno and Las Vegas, one out of every three people living in Nevada work for a mining related industry.

Jan 1, 1991

By P. R. Jochens, D. D. Howat, R. B. Atmore

INTRODUCTION The Miller chlorination process has assumed a preeminent position in the refining of gold bullion, a position it has maintained for over half a century. In the early sixties considerable interest was aroused by the idea of producing a consistently high grade bullion at the mine smelthouses themselves. However, as the use of chlorine in industrial plants is associated with considerable hazards, oxygen was considered a natural alternative, apart from bing less expensive than chlorine. Partial refining at the mine smelthouses would considerably decrease the requirements made on Rand Refinery Limited as well as indicating the possibility of reducing final refining costs. An added factor would be the purer silver chloride obtainable, after prior removal of the base metals by oxygen injection, which would facilitate the production of high-purity silver. The free energies of formation of the oxides of the metals;- silver, copper, lead, zinc, iron and bismuth indicate that, with the exception of silver, these metals should be capable of removal as oxides by oxygen injection. Rose1 had shown that during injection of gold bullion, considerable loss of silver to the boraxsilver slag occurred and, furthermore, that copper removal was not efficient and oxide attack on the refractories was severe. Plant test work2 had confirmed the difficulty of copper removal, but had shown that zinc and lead were almost completely removed. The difficulty of copper removal by oxygen injection warranted further investigation. Also, the high decomposition pressure of silver oxide suggested that by suitable control of the slag composition it might be possible to reduce to very small proportions the silver carried into the slag as oxide. The oxidation of copper by oxygen injection and subsequent dissolution of the oxide in a slag may occur according to the following reactions; Reactions 4 and 5 were considered because of the relatively high solubility of oxygen in molten silver and silver alloys. Thermodynamic data indicate that there is little possibility of any reaction involving the formation of CuO occurring at temperatures above 1 000 °C. To ensure that the operative reactions 1 and 4 take place to the maximum extent, the following factors He significant. (a) an increase in the activity of the copper in the bullion, (b) an increase in the partial pressure of oxygen in the system, (c) an increase in the activity of the oxygen in solution in the metal, (d) a decrease in the activity of cuprous oxide in the slag. From practical considerations, the operative variable most easily susceptible to control is the composition of the slag. SOLUBILITY OF COPPER OXIDES IN BOROSILICATE SLAGS Very scanty information exists on systems containing copper oxides but the indications are that slags containing considerable amounts of boric oxide would possibly prove to be the best solvents for cuprous and cupric oxides. This is attributed to the fact that the activities of copper oxides are much lower in boric oxide slags than in slags in which silica is the main network former. The number of possible slags containing boric oxide was limited by consideration of liquidus temperature, viscosity, corrosive action on refractories, volatilization, and ultimately cost (for industrial application). Slags in the systems soda-boric oxide-silica and lime-boric oxide-silica were selected paying due attention to the above limitations. Additions of 5, 10 and 15 per cent cupric oxide were made to the finely ground, premelted slags. These mixtures were then reground and 2g quantities held in re crystallized alumina crucibles at temperatures of 1150°C and 1 250°C respectively for 30 minutes. The crucibles were removed from the furnace, rapidly cooled, cut in half longitudinally, and a thin section taken from one half was subjected to microscopic examination.

By J. A. Hudson, X. D. Pan

A rock mass responds to excavation according to the properties of the intact rock, the network of contained discontinuities and the susceptibility of the rock mass to weathering. Large deformation often occurs when one of these components causes the rock mass to have a low strength relative to the stress conditions. Analysis of such large deformations forms a significant feature of current numerical modelling in rock mechanics. A practical large deformation problem of roadways in a coal mine is described, demonstrating the requirements for improving numerical techniques. The development of a numerical model is then summarised with particular attention to several concepts pertinent to large deformation analysis in geomechanics. A numerical case study is presented in which the developed finite-element model is used and the results are compared with the in-situ measurements. Conclusions are drawn for rock engineering that are also relevant to both civil engineering and mining engineering projects

Sep 1, 1991

By K. P. Bingham

Lime is one of the largest volume chemicals produced in the United States. In 1979 approximately 21 million tons were produced. Lime is, in fact, second only to sulfuric acid as the largest volume basic chemical produced. Lime, also known as quick lime (calcium oxide) and hydrate lime (calcium hydroxide), is the principle alkali used in a multitude of industrial processes. In addition to its use as a principle industrial alkali, lime has experienced dramatic growth in four general market areas during the past 30 years. These four areas are: 1. Water Treatment - Lime is used extensively in treating and purifying water for industrial and potable use, Although significant tonnage is shipped to this market of municipal and industrial water treatment plants, the end-users are widely spread geographically and individual shipments are relatively low tonnage. Lime, which is nonhazardous, can safely be shipped by truck or rail to these small end-users. 2. Municipal and Industrial Waste Treatment - Environmental agencies at all government levels,

Jan 1, 1980

By Daniel Proszek

A globalização tem tornado o mercado internacional mais competitivo e o setor brasileiro de fundição cada vez mais é ameaçado pela produção asiática que oferece produtos com custos inferiores aos valores nacionais. O meio ambiente é outro fator emergente nos panoramas atuais, empresas com consciência ambiental sofrem com elevados custos para a disposição correta de materiais. Estes fatores são abordados no atual trabalho que focou na adequação de equipamento para regeneração mecânica de areia, tornando possível a reutilização do principal consumível de moldes de fundição. Tendo como base projeto inicial de equipamento de regeneração mecânica, foram aplicadas melhorias e posteriormente foram trabalhadas variações de parâmetros do processo. Oriunda do processo de cura a frio, a areia fenólica usada destorroada industrialmente foi testada variando a velocidade de rotação do atritor (450 e 900 RPM), e o tempo de permanência (10, 20 e 30 min). Os experimentos em areia foram analisados através de distribuição granulométrica, análise de perda ao fogo e também a limpeza dos grãos via microscopia eletrônica de varredura, sempre guiados pelas referências de areia base e areia destorroada. Analisando os resultados encontrados foi possível identificar a influência das variáveis testadas e assim determinar a configuração mais eficiente na limpeza da capa resina que envolve grãos.

Aug 8, 2018

By Edward Jacobsen, Patrick J. Lydon

"The ongoing expansion of the Oak Creek Power Plant in Oak Creek, Wisc., includes a tunnel bored in rock that connects to four vertical intake shafts approximately 1.5 miles (2.4 km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to install these intake shafts. In spite of delays that shortened the May to September construction season by up to 50%, four shafts and liner assemblies were drilled in 2005 and 2006. The shafts were connected to the tunnel in 2007 by mining upward to reach the lower portion of each liner and then removing its internal bulkheads so that lake water fl owed into the tunnel. The project is one of the largest private construction projects ever undertaken in Wisconsin. The expansion adds 1,230 megawatts of generation. In addition to the tunnel and offshore work, there will be 16 miles (26 km) of railroad track and 6 million cubic yards (4,600,000 m3) of earth work. The 27 ft (8.2 m) diameter tunnel, drilled some 150 ft (46 m) below the surface of Lake Michigan, originates onshore at a pump house. A structural slurry wall was constructed as the foundation for the pump house. The tunnel passes to the south near the current water intake before bearing east toward the new offshore intake shafts, which are 12 ft (3.6 m) diameter by 108 ft (33 m) long steel liner assemblies. These were grouted in place from approximately 3 ft (1 m) above the crown of the intake tunnel and then to 20 ft (6 m) below the lake bottom.Site GeologyOffshore. The plant site is north of the Racine-Milwaukee county line in an area affected by glacial activity. The soil conditions encountered at each shaft location were consistent, with noticeable variations occurring in the top of rock elevations that sloped downward from the innermost to the outermost shaft."

Jan 1, 2008