Search Documents

By E. H. Rose

THE question is often pondered whether the flotation process is still an art or has become a science. The fact is that flotation is a science in so many variables that only art can blend them. It is demonstrable that no less than one hundred variables are involved in any flotation operation, most of them immeasurable on a routine basis. The behavior of every one of them is always governed by orderly and unchanging law, as no man can doubt. There is nothing truly indefinite about that behavior; the only indefiniteness is in our knowledge of it, either in general or from hour to hour in the circuit. In dealing with a simultaneous equation in, say, one hundred variables, all not only affecting the outcome to some degree but many influencing each other as well, it is small wonder that the mineral-dressing profession presents a case history of debate and controversial opinion. The statement of the subject of this symposium-a symposium on flotation machines-seems to delimit and define the matters to be considered and at least the general nature of the conclusions sought. Nevertheless, in such a meeting it is not possible to meditate upon all the variables that do in one way or another affect performance of flotation machines. To attempt it would be much like trying to operate a hundred-ring circus. Perverse variables being what they are, one could expect the elephant in ring 36 to squirt a trunkful of water at the tightrope performer in ring 37 to ruin that artist's act, just as our learning to depress pyrite in the early 1920's ruined the act of the formerly faithful old Callows. HONEST DISAGREEMENTS Selective flotation dates from 1922 or 1923, when several plants established their regular flotation operations on a selective basis. Since then, two decades of efforr have gone into the development of better and better flotation machines. Many have come and gone. The competition has simmered down to perhaps a dozen machines, each one of which is staunchly defended by some operators as being the best for their particular jobs, and as scornfully dismissed by at least a few others elsewhere as being positively the poorest for theirs. These disagreements are honest disagreements, honestly arrived at after plenty of sweat. In many a flotation plant, one machine has been tried out against another under conditions as fair as they could possibly be made. Sometimes the results are on a par but more often one machine shows a consistent and unmistakable margin of superiority over the other. In equally honest and enlightened tests, machine A may win over machine B in one place, and machine B over machine A by as great a margin in another. This paper purposes to identify some of the more prominent reasons why this is so,

Jan 1, 1944

By D. S. Eppelsheimer, D. N. Williams

The compression texture of iodide titanium is determined and found to consist of a [0001] texture rotated 15° to 30° from the axis of compression. As the amount of reduction increases, the angle of rotation decreases. The 0001 rotation showed a slight preference for a <1010> rotation axis. RECENT investigation of the cold rolled texture of titanium&apos; has shown this metal to exhibit a new type of rolling texture. This texture can best be described as a (0001) [10i0] with the 0001 planes rotated approximately 30" to the transverse direction around a <10i0> rotation axis. Rather good results in explaining the cold rolled texture have been obtained by other workers&apos; by examination of the tension and compression textures. No information was found giving the tension texture of titanium. Generally the tension texture of a hexagonal close-packed metal is identical with its wire texture. The drawn texture of titanium has been investigatedh nd has been found to be predominately [10?0]. Since this is the common tension texture of hexagonal metals of low c/a ratio, the explanation of the difference between the rolling texture of titanium and the rolling texture of other hexagonal metals is not indicated by examination of the tension texture. Therefore, the compression texture of titanium should be particularly important in the explanation of the unusual transverse rotation of the 0001 planes found in the cold rolled texture. The compression texture of titanium was examined by Yen.",&apos; His results showed titanium to exhibit the usual [0001] texture up to 85 pct reduction. At higher reduction a double texture appeared in which the 0001 planes were rotated from 10" to 30" from the plane of compression. This change in the compression texture seemed unusual since the tendency for hexagonal close-packed metals is to approach the [0001] texture as the idea compression texture. Mechanical twinning generally occurs over a considerable range of reductions beginning at a rather low reduction. The samples used by Yen in his investigations were prepared by two methods. Compression in a testing machine was used up to a reduction of 85 pct. Compression by compression rolling was used at higher reductions. Since the change in texture occurred at the same reduction as the change in the method of compression, a connection between the two seemed likely. To check this possibility and to locate the position of the change in texture definitely, if it was found to exist, the compression texture of titanium was re-examined. An iodide titanium crystal bar (99.9 pct Ti) produced by the New Jersey Zinc Co. and donated by the Titanium Alloy Manufacturing Div. of the National Lead Co. was used in this investigation. Procedure The investigation of the compression texture was carried out in three steps; compression, specimen

Jan 1, 1953

By Oliver Ralston

DURING experimental study on the separation of a zinc concentrate from the heavy sulfide ores of Jerome, Ariz., a great deal of attention has been given to proper activation of the sphalerite content of the ore. The sphalerite at Jerome contains enough iron to class it as a marmatite, as picked specimens have only about 60 per cent. zinc, whereas pure zinc sulfide contains 67 per cent, zinc. This marmatite in large pieces is black in color, but in dry powdered state is brown. A flotation froth made from it has a silvery black luster in comparison with a brassy luster caused by chalcopyrite which occurs in the same ores. The sample used in most of the experiments described below consisted of about 3000 lb. of diamond-drill core from the zinc-bearing orebodies of the United Verde mine, and had the following analysis: PER CENT. PER CENT. Oz. PER TON Cu 0.695 A1203 0.83 Ag 1.30 Zn 6.17 S...:: 43.35 Au 0.02 Fe 36.23 CaO 0.46 Si02 9.27 Mineralogically, this analysis is calculated to the following, which is in agreement with the microscopic examination: PER CENT. PER CENT. Chalcopyrite 2.0 Schist 3.2 Marmatite 10.32 Quartz 8.2 Pyrite 73.0 Calcite 0.9 All samples were ground in a laboratory ball mill in order to leave about 3 per cent. on a 200-mesh sieve, fine grinding being essential to liberate the minerals in the ore. Most of the Jerome ores are so intimately crystallized that reasonably complete unlocking by grinding does not take place until 800 mesh is approached. Therefore, the 200-mesh grind adopted contains a considerable amount of locked mineral grains, but not so much as. to render impossible the preparation of commercial grades of concentrate:

Jan 1, 1929

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

By W. A. Hoyer, G. A. Lock

Laboratory and field tests have shown that it is feasible to log for copper in a qualitative way using the techniques of neutron activation analysis. Laboratory tests showed that the 0.51 and 1.04 mev gamma rays of 62Cu and 66Cu, respectively, could be diagnostic. However, in the core holes, the detection of copper was limited to 0.3% concentration because of interferences from the 18Si and Al gamma rays. Both stationary and continuous logs were made, but only the stationary data yielded a recognizable copper response. This response consists of a combination of two effects-the direct response from copper at 0.51 mev and an increase in low energy gamma ray absorption due to mineralization. Both low energy chemical (PuBe) and high energy accelerator neutron sources were used for the laboratory and field tests, while the same 2 X 5 in. Nal scintillation detector served for all the tests. Potential improvements in copper detection might be possible with solid state gamma-ray detectors which have better gamma ray resolution but much less detection efficiency. This type of activation logging requires complex equipment and trained personnel to conduct field operations and may find application where coring is difficult or prohibitive.

Jan 1, 1973

By Stephan Iversan, Janae Singer

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in rock. Excavation blast damage can be as shallow as 1 to 2m (3 to 7ft) and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m (0.8 to 1.6ft) along mine walls. The resulting tomograms of P-wave velocity show low velocity zones which we interpret as residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock.

Jan 1, 2009

By F. Turatti

Rio Tinto is one of the world&apos;s largest mining companies, involved in every stage of metal and mineral production, producing aluminium, copper, diamonds, coal, iron ore, uranium, gold and industrial minerals. Operations are in more than 50 countries in multiple continents and vary in location between large urban centres, regional industrial complexes and remote regions. A risk-based strategy was developed by Rio Tinto to manage its air quality impacts on a global scale. The strategy consists of three objectives ? improving air quality performance, developing industry leading practices and engaging and influencing in air issues. This paper discusses three major successes achieved this approach. Firstly, how air shed resources are managed in constrained air sheds. Secondly, how financial modelling is used to value air quality constraints, and thirdly, how a rigorous and comprehensive e-learning course is used to improve the overall level of air management knowledge of Rio Tinto?s environment managers.

Feb 27, 2013

By K Le Bron

Fatalities that occurred because of rock falls in off-reef excavations (excluding shafts) over the last three years range between ten per cent and 20 per cent of the total number of fatalities that have occurred due to rock falls in the South African mining industry. These rock falls, mostly exacerbated by blasting practices, occur because of failure on discontinuities within the rock mass. Among other reasons of their occurrence is insufficient support installation or the incorrect assessment of rock mass conditions. This report presents qualitative analysis intended to outline rock stability conditions in tunnels subjected to dynamic loading. Seismic waves including those created by firing an explosive charge in tunnel rocks are considered. The rock behaviour is monitored using geophones and extensometers variably installed to record the near and far effects of roof bolt support units on a dynamically loaded rock. The paper discusses the results of field investigations.

Jan 1, 1999

By Rod A. Levander, Kenneth B. King

INTRODUCTION The Panna Maria Uranium Project is located in South Texas, between San Antonio and Corpus Cristi, approximately 10 kilometers (6 miles) north of Karnes City, Texas. The tailings disposal facilities are located immediately south of the mill area and the central portion of the west pit. The mine and mill drainage pond is located north of the tailings pond. Location of the facilities is shown in Figure 1. The tailings pond is a disposal area for mill process wastes and has a capacity for storage of approximately 9 million metric tons (10 million tons) of tailings. This capacity is adequate for approximately 10 years of milling at a maximum rate of 2,700 metric tons (3,000 tons) per day. The tailings disposal facilities were designed to essentially eliminate discharge of contaminated waters to preclude degradation of surface streams or ground water. Water levels in the ponds will be maintained. through reuse in the mill and by evaporation. WASTE CHARACTERISTICS The sources of waste that is stored in the tailings pond include runoff from the mill area and tailings from the mill processing. The tailings consist of a sand slime slurry; the percentage passing the No. 200 sieve varies depending on the ore material, and it is generally in the range of 10 to 25 percent. The tailings have a density of approximately 1.2 metric tons per cu m (75 lb per cu ft) and an average specific gravity of 2.55. The liquid effluent from the mill consists of waste solutions from the grinding, leaching, extraction, and washing circuits of the mill. These solutions have an initial pH of 1.5 to 2.0 and contain the remnants of the leaching agents used in the mill process, sulfates, some silica as the primary dissolved solid, and trace quantities of soluble metals. This liquid is discharged with the solids into the tailings pond and is diluted by rainfall and runoff from the tailings dam. Runoff from the mill area, drainage from the mine area, and de-oiled water from truck washing facilities is discharged into the mine and mill drainage pond. Runoff from the mill area drains approximately 28 hectares (70 acres) from offices, shops, the mill site, the ore pad, haul roads, and adjacent areas. Mine drainage is collected in the mine area and pumped to the mine and mill drainage pond.

Jan 1, 1980

By Norihiro Murayama

Syntheses of zeolitic materials were carried out from coal fly ash by alkali hydrothermal treatment as part of the reuse and recycle technologies of coal ash, For the obtained zeolites, the cation exchange capacity and acid resistance, which are very important in the practical use of cation exchanger in aqueous solution, are investigated during this stufY, The cation exchange amounts of the NaP, CaP and K-CHA zeolites are measured for various cations such as K+, Na +, NH4+ Ca2+, Mg2+, Pb2+, Cd2+ and so on. The change in crystallization degree are researched as a function of pH. The simultaneous removal ability of NH4+ and PO43- in solution is examined for an example of the water purification with CaP zeolite. From these results, the characteristic and its mechanism of cation exchange are clarified for the various zeolitic materials obtained from coal fly ash.

Jan 1, 2003

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

Jan 1, 2006

By H. A. Bourne, E. L. Haden, D. R. Reichmuth

A circumferential-toothed bit with novel tooth form gave improved penetration performance. In this design the exterior flank of all teeth were vertical when in rolling contact with the hole bottom. Rock chips were generated by the interior flank of the tooth displacing the rock inwardly and downslope toward the center of the hole. A unique two-cone laboratory bit assembly enabled evaluation of numerous cone and tooth configurations. Some of the variables investigated, in addition to weight on bit, rotary speed and rock type, were tooth interference, percent tooth, hole bottom angle, attack angle and relief angle. Most tests were conducted dry on a brittle synthetic sandsone or a ductile quarried limestone. Tooth configurations were found to be more significant in the ductile material. This was attributed to the deeper tooth penetration before rock failure. These studies showed that the attack angle (angle beween interior flank of the tooth and rock surface) was the controlling variable; changing the tooth configuration from the assymetric or semi-wedge to the more conventional symmetric or wedge form reduced penetration performance; and penetration performance of circumferential-type cutters was directly proportional to rotary speeds up to 200 rpm. INTRODUCTION Much of the published literature on rock-chisel interactions describe experiments wherein symmetrical wedges are vertically loaded or impacted against a smooth rock surface.1-6 are is usually taken to insure that the indentation is not made near the edge of the rock specimen less erroneous data be obtained. The literature describes relatively few studies in which the investigator deliberately attempted to take advantage of an edge or free surface. In contrast, anyone who chips ice or breaks up a concrete sidewalk almost always works near an edge. Chisel "indexing," which has been considered by some investigator1,2,6,7 makes limited application of an edge or free surface. Probably the best documented investigation into applying this idea to drilling was that of Drilling Research Inc. at Battelle Memorial Institute.&apos; Their "annular wing" percussion bit consisted of paired asymmetric chisels oriented so as to produce and move chips to the center of the hole. They predicted that the lowest energy requirement for chip generation would be achieved with a stepped hole bottom having a median angle of 45" to the horizontal. Results from limited tests showed that approximately 50 percent of the rock fragments were large and semi-circular in shape, as would be expected by a chisel impact near an edge. The remaining 50 percent were fine chips produced by the chisels in re-establishing the steps or ledges. Initial penetration rates with this bit were high, but they rapidly decreased. This was the result of excessive tooth wear caused by the constant friction on the gauge surfaces. The basic idea — circumferentially placed asymmetric chisels — still appears to have merit. If the concept could be applied to a rolling cutter bit, two of the shortcomings of the fixed chisel design could be overcome: (1) reduction in tooth friction, and (2) greatly increased cutter surface. Adapting asymmetric chisels to cutters rolling on an inclined hole bottom is restricted by bit geometry. The basic elements of roller rock-bit construction prevents the practical attainment of a 45" hole bottom angle. Nonetheless, experimentally it was considered desirable to investigate the influence of hole bottom angle to at least 40". This paper describes the laboratory studies conducted in evaluating the circumferential-toothed roller cutter rock bit. EXPERIMENTAL APPARATUS AND PROCEDURE BIT ASSEMBLY The cost of constructing a sufficient number of conventional three-cone rock bits to investigate circumferential cutter performance was prohibitive. Instead, a novel two-cone laboratory assembly which used an external bearing system was designed and constructed. The external bearings made it possible to alter the journal bearing angles and thus allow a wide flexibility in cutter configuration. Fig. 1 shows the laboratory bit assembly, the various bearing mount plates and the appropriate roller cutters for drilling shallow holes having hole bottom angles of 0, 10, 20, 30 or 40". The bit was limited to a drilling depth of 1 1/2 in. at the gauge teeth and a hole diameter of 43/4 in. This more or less intermediate size bit was chosen because it gave a more realistic match between bit teeth and the rock than would a microbit. Also, the rock sample size required was convenient and easy to obtain. CIRCUMFERENTIAL CUTTERS The tooth configuration used in our initial studies is shown in the upper half of Fig. 2. All cutters used in this series had the same tooth form — 43" included tooth angle, 2" positive relief angle and a horizontal tooth flat width of 1/32 in. Each cone cuts alternate rows except for the gauge row. The row-to-row spacing in view was 1/4 in. Static loading tests conducted earlier with asymmetrical chisels had been used to establish this spacing. These tests showed energy requirements for chip production increasing rapidly as the distances to the edge increased beyond

By G Love, S Maher

In Victoria’s onshore Gippsland Basin, geology is driving brown coal developments, and geologists are key decision-makers. Prompted by volatile energy prices and the likelihood of a carbon constrained future, significant work has been carried out on the next generation of technologies to be applied to this giant resource. These include new-generation gasification technologies, coal conversion processes yielding products as diverse as diesel and fertiliser, drying technologies producing thermal and metallurgical coals and in situ conversion processes. However, coals aren’t coals, and brown coal available for new projects will have different quality parameters and mining economics from that currently mined.New projects are likely to be developed on coals with moisture contents averaging 60 per cent and corresponding low energy values. Whilst ash values will be low, averaging just 5 per cent (dry basis), this will at times approach 10 per cent, which is a level that would challenge the installed-generation technologies. Sulfur values will average 0.4 per cent (dry basis), but at times exceed 0.6 per cent, requiring technologies that address the potential for sulfur dioxide emissions. Whilst localised high levels of the fluxes iron (&gt;1 per cent dry basis) and sodium (&gt;0.3 per cent dry basis) would increase fouling of installed technologies, they may be suitable for selected next-generation technologies.Project viability for this next generation of technologies will be strongly influenced by mining cost, and geologists are playing a role in identifying higher-value coal. At its simplest, this is being achieved for open cut mines through regional, vertical strip ratio assessments, which are considered a first-order proxy for mining cost. Follow up assessments are incorporating mining and processing cost, coal quality penalties and product revenues. At a regional scale, it is informing the likely location and relative timing of future mine developments, as well as thinking around rehabilitation strategies, infrastructure and land-use planning.For deeper coal, factors like macro permeability, the ability to isolate seams from aquifers, groundwater chemistry, pressure temperature conditions, connection with groundwater recharge and in situ biota are being used as vectors to in situ coal conversion opportunities.Matching coal to the next generation of technologies has benefited from regional-scale geological studies of coal quality and mining economics, and has benefited from early engagement between geologists, technology developers and project proponents.CITATION:Maher, S and Love, G, 2014. Matching brown coal to the next generation of Latrobe Valley projects, in Proceedings Ninth International Mining Geology Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Australian underground coal mines predominately use the longwall method for coal extraction. In longwall mining at least two parallel roadways known as gateroads are mined to delineate the sides of the longwall block, a longwall installation face is then driven connecting the gateroads to enable the longwall mining equipment to be installed. Roadway development should ideally be ahead of the longwall so that the longwall equipment can be installed into the newly developed panel with minimal delay to coal production. A discrete event model of roadway development can help assess how a particular configuration may perform with high levels of variability and uncertainty in operations. One of the major delays associated with roadway development is caused by the shuttle car due to its cyclic stop-start nature. Shuttle car travelling paths and machine interactions are normally constraint by the mine?s roadway layout and mine safety issues. This paper presents simulations of shuttle car route options which can be considered at the design stage to minimize the cycle time of a shuttle car as part of a general roadway development simulation model developed using 3D Flexsim.

Feb 23, 2014

By M. Gangal

CANMET-MMSL, in cooperation with Dry Systems Technologies and Quinsam Mine, conducted a study to determine the effects of B50 biodiesel on the emissions of a flameproof diesel power package in comparison with mining diesel fuel for application in underground coal mines. The emissions testing for coal mine application requires that the intake air mixture to the engine should be at 1.25 percent methane by volume in air. The tested power package system included a naturally aspirated, mechanically-controlled diesel engine with a diesel oxidation catalyst (DOC), a heat exchanger, flame arresters, and a low temperature disposable diesel particulate filter. The engine dynamometer tests were conducted at the CANMET-MMSL Diesel Emissions Research Laboratory in Ottawa using the ISO 8178-C1 test protocol. The separate and combined effects of a B50 biodiesel blended fuel, and with and without 1.25% methane enriched intake air were measured on a diesel power package. Fuelling the baseline engine (without methane), with B50 biodiesel blend reduced carbon monoxide (CO) by 44%, and increased nitrogen dioxide (NO2) by 19%, and particulate matter by 31% relative to the mining diesel fuel. Similarly, injection of 1.25% methane to the intake air for baseline engine with mining diesel fuel increased engine power by 15%, CO by 124%, and NO by 15%, and decreased NO2 by 13%. The effect of B50 biodiesel relative to the mining diesel for coal mines application (with methane for both fuels) was to reduce CO by 27%, and NO by 6%, and increase NO2 by 23%, with no change in engine power. The overall results indicate that the minimum ventilation rate for the equipment application in coal mines with B50 biodiesel was 4.11 m3/s (8,700 cfm), slightly higher than the ventilation rate of 4.01 m3/s (8,500 cfm) with the mining diesel fuel. This slight increase in ventilation rate for B50 biodiesel fuel was due to an increase in NO2 at one of the operating test points, and the ventilation rate for this equipment was governed by NO2 in the exhaust gas.

Jan 1, 2009

By A R. Cameron

"The number of commercial explosive products available to the mining industry has been steadilyincreasing and associated with this there has been an increase in the range of characteristics or properties of them. This has lead to increased difficulties in selecting the most appropriate explosive for a particular blasting situation. Techniques are available that can be used to evaluate and compare the characteristics of explosives under a range of conditions. Also, the techniques are used to assess the variability in the characteristics between batches."

Jan 1, 1994

By Verya Nasri, Scott Thorburn

The City of Toronto and the Toronto Transit Commission (TTC) have conducted an Individual Environmental Assessment (EA) for a 6.2 km, 4-station underground extension of the Spadina Subway from Downsview Station to Steeles Avenue. This Environmental Assessment Study was performed in three phases including routes and general station locations, alignments and station concepts and detailed assessment of the effects of the undertaking. URS Canada Inc. has led the consultant team for this Study. The anticipated total duration of the project is approximately 6 years and its estimated total cost is about $1.4 billion. This paper presents the planning process of the project, the environmental and engineering challenges, and the measures taken to address them.

Jan 1, 2007

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By Tuan V. Nguyen, Louis Mittoni, Murray Rudman, CSIRO Minerals, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D “Improving Thickener Technology” project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003