Search Documents

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By P Krauss, S Harpalani

Methane emitted from underground coal mines, along with ventilation air and known as ventilation air methane (VAM), constitutes the largest component of coal mine methane (CMM) emissions. Atmospheric methane, on the other hand, is a potent greenhouse gas with a significant adverse impact on the atmosphere. This has led to the development of various technological alternatives for its use as an energy fuel. Techniques involving oxidation of VAM, usually consisting of very low concentrations of methane, have been validated in the past. Prominent among these technologies are the thermal and catalytic flow reversal reactors, ancillary fuel technologies, lean fuel gas turbines, and concentrators and gasifiers. However, the efficiency of any VAM utilisation technique depends on the amount and concentration of methane in the ventilation exhaust air. Therefore, quantification of VAM emission from a coal mine is the first step towards identifying the most suitable technology for its utilisation for energy production. This paper presents an evaluation of the efficacy of VAM as an energy source. It provides details of a case study aimed at developing a technique to accurately quantify VAM emission from a coal mine. It further discusses the various VAM utilisation techniques available, and presents an economic evaluation of the alternatives. Based on the findings of the study, the most feasible method for VAM utilisation is identified for the mine. The paper summarises the procedure for quantifying VAM emissions and selecting the most suitable utilisation technique.

Jan 1, 2005

Visual computing opens the design process to a wider audience and allows rapid communication of mine plans to all stakeholders. The integration of software and hardware technologies that take advantage of a graphical environment will continue to improve both long-term and short-term mine design (Figure 1). A good design must be adaptive to respond to decision changes as the mine develops and more information becomes available. The constraints on mine design predicate careful analysis in order to operate the mine as efficiently and safely as possible.Continuous improvement in mining is assured by developing innovative technologies that target mine survey, drill and blast, modelling, short-term design and pit and stope optimisers. The design life of a mine has to be sufficiently long to ensure the mine is commercially successful, justifying the high start-up capital costs. Being able to execute a plan so that it honours the design realises the rewards of computerised mine planning and the long-term investment in data acquisition.

Sep 26, 2011

By Frank G. Miller, Ralph A. Seban

Problems relating to thermal methods of oil recovery have been given increasing attention during the past year. The nature of the physical and chemical processes underlying thermal recovery are not yet well understood. The need for pertinent basic information is recognized generally. One of the processes involved is the transfer of heat by conduction in oil reservoir rocks containing moving reservoir fluids. This technical note deals with heat conduction in a laboratory sand column filled with a moving hydrocarbon and therefore should be contributory to the presently inadequate fund of knowledge on thc over-all subject. In an analysis of the flow of vaporiziny propane through a horizontal column of sand, one of the present author9 demonstrated correspondence between thc measured values of pressure along the length of the column and those predicted by a theory which postulated that the enthalpy of the propane was invariable along the length of the column. This postulate way implied as a deduction from the principle of conservation of energy but the details of the deduction were not given. The specific purpose of this technical note is the presentation of these details both as an adjunct to the earlier analysis and to supply some additional details on the processes involved in this type of flow. Results disclose that rates of heat transfer by conduction, in the direction of fluid motion, generally would be small for systems of the type studied. FUNDARIENrAI. ENERGY EiQUAI-[ON The principle of conservation of energy may be applied to a section of the porous material on the basis that heat transfer, like fluid flow, is possible in the x direction only. Transfer of heat in the y and z di'rections is prevented by suitable insulation or by taking the medium as infinite in directions perpendicular to the x axis. For steady state heat conduction and conditions of steady fluid flow the principle of conservation of energy specifies that any reduction in the enthalpy rate increases the flow of heat in the same proportion. Stated mathematically, dH KA 87 —- = - — - — U) * dx W dx........ Lvhere is the flow of heat in the positive x W dx direction. TEMPERATURE DISTRIBUTION IN DIRECTION OF FLOW The column of sand used in the previoi~sly described research is divisible into three different flow regimes. each of which may be analyzed independently. In the entrance region the liquid approaches the saturation state. A transition region is postulated following the transverse section at which the saturation state of the liquid is attained. In this transition region gas and liquid phases are both envisioned as present, with no vaporization occurring and with fluid movement restricted to the liquid. The upstream end of the exit region is at the transverse section of the column where the fraction of the pore space occupied by gas first becomes great enough for gas flow and where vaporization of the liquid begins. Fig. 1 indicates schematicaHy the thermodynamic processes undergone hv the fluid in the three flow regimes.

Jan 1, 1956

By Don Novotny, Dana Spencer

In this workshop our intent is quite simple; that is that we will introduce a relatively new technology that may have applications in blasting applications. This technology is the laser initiation of explosives. This workshop course is not intended to suggest ways in which specific blasting problems can be resolved. That is the purview of experts within each of your fields.

Jan 1, 1994

By Z. T. Bieniawski

The efficient and safe design of room-and-pillar coal mines still remains as one of the pressing problems facing the mining industry in the United States. Present day design is a trial-and-error approach based mostly on experience. Although much research has been directed to stability of mine roofs and coal pillars, no generally-accepted design method has been formulated. This paper reports on a three-year research effort directed to an improved design of room-and-pillar coal mining in the U.S.A. Essentially the study consisted of three aspects: (i) determination of stable roof spans; (ii) determination of the strength of coal pillars; and (iii) determination of safety factors for room-and-pillar coal mining in the United States. Furthermore, three novel approaches were utilized during this research: i) the "petite sismique" technique was assessed for possible determination of coal pillar deformability ii) the "Geomechanics Classification" was extended for determination of safe roof spans in room-and-pillar coal mining. iii) a national survey of the current design practice and mining dimensions was performed with the aim of assessing factors of safety for room-and-pillar coal mining The outcome of this work, which is summarized in this paper, is a design code for room-and-pillar mining in the United States.

Jan 1, 1983

By Michael Gauna

A high seam geologic condition exists at Jim Walter Resources No.4 mine which requires immediate rib support after a continuous miner cuts a place, High seam mining heights are typically 2.4 to 2.6 m (8 to 9 it) and a thick rock layer is present in the upper portion of the coal rib side. The 610 m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 30.5 cm (12 in) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas which endanger men and equipment. To control this situation rib support must be installed in the roof bolting operation as the bolting crew works towards the face. A rib control system has been developed for this high seam mining condition utilizing a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDFI- 15 bolting machine. Over 120 km (75 mi) of entry have been supported with angle rib bolts. These angle bolts constitute 43 to 60% of the total roof and rib bolt footage in the high seam port- ions of No.4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method employing bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people and the total drilling supply costs are approximately 60% the previous cost, when compared to the previous support method using horizontal rib bolts.

Jan 1, 1983

By Patrícia Mundim Campos Faria

The process of particle size reduction by grinding is inherently inefficient and involves high capital and operating costs. In particular, ball milling is one of the important unit operations in the iron ore pelletizing process. The mill product, due to its physical properties, determines the efficiency of subsequent stages of classification, filtration and pelletizing, thus impacting the quality of iron ore pellets. The work demonstrates the application of the population balance model in the optimization of a full-scale ball mil circuit grinding pellet fines with the aim to evaluate the optimal solids concentration to improve iron ore pellet quality. Initially, detailed experimentation was carried out in a 25.4 cm diameter batch mill and a relationship for mill scale-up using a linear population balance model in wet grinding systems was established. The selection and breakage parameters and the specific selection functions were determined for pellet feed iron ore. It was possible to identify the non-normalizable nature of the breakage functions of the ore studied, which were modeled properly. Afterwards, as a result of incorporating the specific selection functions and breakage functions into the linear population balance model, it was possible to predict product size distributions in the pilot and plant scale mills (0.416 and 5.18 m diameter, respectively) from data obtained in the 25.4 cm diameter mill. Finally, with this scale-up procedure it was possible to appraise the plant scale optimization via laboratory scale grinding mill tests. The effects of changing percent solids were assessed in order to improve the industrial mill performance and the optimal value should be in the range from 76 to 80%.

Aug 1, 2018

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology (Le. stratification, turnover, and development of anoxic conditions with depth) of the lake. Limnologic data collected from four existing pit lakes indicate that pit lakes develop a thermocline, or temperature stratification, in the upper 10m to 30 m of the water column. Two of the pit lakes (26 m and 55 m deep) undergo seasonal turnover of the entire water column, whereas two deeper pit lakes (110 m and 240 m) undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column and a distinct chemocline develops with depth.

Jan 1, 1996

By Oliver Smalley

EXCEPT for the work of Guillet, who conducted a systematic investigation on the zinc-replacing value of nickel in brass, and extended his investigation with a view to developing commercial high zinc content nickel brasses, the author does not know of any systematic research on the subject. The most promising commercial alloys and their physical properties obtained by Guillet are given below: Maximum Elonga- Reduction Copper Zinc Nickel Stress, tion, of Area, Brinell Tons Per Per Cent. Per Cent. Sq. In. 55.0 41.0 5.0 24.4 46.5 94 Sand cast. 22.6 27.0 90 Chill cast. 56.7 39.74 3.35 30.0 43.0 51.7 97 Casting annealed 2 hr. at 750° C. 33.9 33.0 50.7 144 Cold-drawn bar. 55.15 42.3 2.24 29.8 33.0 116 Casting annealed 2 hr. at 750° C. 32.3 29.0 151 Cold-drawn bar. These test results scarcely justify the use of such quantities of so expensive a metal, and could have been obtained from ordinary commercial brass. For purposes of comparison, the physical properties of ordinary brasses, ranging from 70 per cent. to 50.1 per cent. Cu in both the cast and normalized1 conditions are included in Table 1. These incidentally furnish a useful standard of the properties of castings and of rolled, extruded and forged brass when correctly annealed. A close study of some of the well-known special brasses containing nickel reveals a series of alloys which bewilder by their complexity, and one can only hazard a guess at the function and commercial value of each of the many elements used.

Jan 10, 1925

By C. Douglas Lee

This case study describes the work done at the University of Arizona on the development of a computer mine model for an irregularly shaped and spotty ore deposit. The purpose of the work was to develop techniques for modeling any highly irregular deposit, for which the regular 3D fixed block model is not well suited. The deposit contained complex geology consisting of sedimentary beds that had been faulted, thrusted, and intruded by igneous rocks (see Fig. 1). The physical dimensions of the modeled ore body were 1067 m (3500 ft) along the N-S direction and 914 m (3000 ft) along the E-W direction. Topographic relief in the modeled area was approximately 274 m (900 ft). The highest grade of ore was found near the surface with mineralization extending down to approximately 152 m (500 ft) below. Using a fixed bench height of 12 m (40 ft), the model required 25 levels with the highest elevation being at 1286 m (4220 ft). Fig. 2 shows a cross section of the developed computer model of the ore deposit. The particular modeling approach selected for this deposit was the 3D irregular block model.* This meant that only the dimension of bench height was fixed at 12 m (40 ft). Irregular size blocks in the form of polygons were adopted in the model to describe the ore zones and geologic contacts. The following sections of this chapter describe some of the techniques used in modeling.

Jan 1, 1979

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

Almost all of the flotation reagents used today were discovered by continued application of empirical methods and/or trial and error experimentation. Moreover, with the metal-ion specific approach used so far, it is difficult to separate the minerals containing the same constituent metal ion. A critical assessment of molecular recognition processes involved in biomineralization suggested the possibility of using reagents which are surface specific. The concept that the molecules consisting of two or more functional groups having appropriate spacing between those so as to achieve structural/stereochemical compatibility during interaction with the mineral surface exhibit structure-specificity is thought to be extended to the design of specific collectors in flotation processes. In the present study, for the first time, a rational design of surface active molecules, and thereby the recognition of crystal faces (of minerals) by these molecules through structural and stereochemical matching is being utilized successfully to selectively float various minerals. For this purpose, carboxylate-based collectors (for mineral specific flotation of calcium minerals) as well as xanthate-based collectors (for mineral specific flotation of sulphide minerals) with a fixed alkyl chain length but having two functional groups with varying geometrical distances (separated by a spacer of one, two and three carbon atoms) between them have been synthesized. In this article, we have discussed the design, synthesis, purification of these novel mineral specific collectors as well as their important solution parameters in relation to flotation processes.

Jan 1, 2014

By Jr. Babcock

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd., in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain Ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 kilometers. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fibre in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd. Of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This paper will present the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits will be outlined. Subsequent work by other companies will be mentioned, but not described in any detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd., who have been involved in the project, particularly Ramon Farmer, N. G. Comer, and A. W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this report are solely that of the author and result from his involvement in discovery of the deposits and management of the exploration program.

Jan 1, 1978

By Richard Keith Corbin

INTRODUCTION With the world media full of predictions that the price of gold will quadruple in three years (Maybury, R.J., 1988), and with financial forecasters and strategists touting opportunities to make 400% in gold (Skousen, M., 1988), explorationists and entrepreneurs are scurrying to find enough gold to feed the global gold fever created. At the same time, gold deposits in the United States and other developed and intermediate countries are becoming less attractive because of environmental restrictions, radical reductions in tax incentives, and depleting reserves, causing people in the mining industry to begin looking at opportunities for foreign investment in gold mining concessions in lesser developed countries (LDCs). Meanwhile, LDCs are responding with chamber-of-commerce aplomb in marketing their opportunities. In the face of all this frenzy and hype, targeting gold mining concessions in LDCs for foreign investment may be done more objectively by employing a systematic approach. For this paper the SHOP rating system (Corbin, R.K., 1987), which considers factors of the LDC's stability, hospitability, ore occurrence, and profitability potential is used. The result is that a tiny banana-growing republic in Central America, first discovered by Columbus and named the "Rich Coast'' because of the many gold adornments worn by its Indians, has been rediscovered and emerges as a classic LDC gold target.

Jan 1, 1988

By D. W. Euler, B. J. Clauzier

"Implementation of an effective energy management system will reduce energy costs without impacting negatively on production.The energy management system must be designed to complement the operation and be integrated with the organization. It must be reliable and easy to use but most important, it must have an accurate and timely feedback reporting system to allow the operation to take appropriate action.Falconbridge Limited was one of the first three companies to be awarded the energy monitoring demonstration program in May 1987. The program is sponsored jointly by the Ontario Ministry of Energy and Ontario Hydro.This paper describes the approach taken by Falconbridge Limited to implement the Onaping Area Energy Management System.IntroductionThe objective of the project was to implement an effective energy management system, capable of reducing energy costs without impacting negatively on production.Energy management systems must be designed to complement the operation and to be integrated with the organization. The system must be reliable and easy to use, but most importantly, it must have an accurate and timely feedback reporting system to allow the operation to take appropriate action."

Jan 1, 1990

By Williams J. D

Magnetite has been used in coal processing for many years and it is likely that its use will continue well into the twenty first Century. While magnetite is only a minor cost component in coal processing, the use of processed magnetite in dense medium separation is essential to provide the split of quality coal products which the markets of today demand. The occurrence of magnetite in Australia is relatively abundant, but a combination of its iron content, magnetic properties, quality and proximity to the coal processing plants is essential to provide a low cost product for use in the Coal Industry. The demand for more splitting of coal in coal processing may require more grades of magnetite, particularly as a finer grade lower specific gravity medium to separate the finer quality low ash coals.

Jan 1, 1991

By understanding the ore breakage characteristics and utilising comminution circuit modelling, the benefits of SAG mill feed size manipulation can be readily assessed. This paper looks at the benefits and problems of total secondary crushing of mill feed and advocates partial secondary crushing as a means of improving grinding efficiency for certain hard ores. Case studies are reviewed for new and existing SAG mill circuits.

Jan 1, 2007

By Kausik M. Sinha

Hydraulic stowing, which is being practiced in several major coal producing countries to deal with adverse mining conditions, usually permits almost 100% coal recovery from underground mines with minimal and controlled surface subsidence. It can be implemented in the US coal mines to reduce the severe effect of land subsidence and at the same time improve the cost of coal production, both of which are major setbacks for the coal industry in the USA

Jan 1, 1989

By K. Tozwa

The electrical conductivity of electrolytes for copper electrorefining and electrowinning processes has been reported by many researchers since 1911. The experimental results show that the conductivity increases with an increase in sulfuric acid concentration and decreascs with an increase in copper concentration. In pure copper sulfate solution, however, the conductivity increases with an increase in the copper concentration. After confirming the conductivity of pure and acidified copper sulfate solutions experimentally, the concentrations of hydrogen ion and free (not hydrated) water in the electrolytes were estimated and it was found that the relation between the conductivity of acidified copper sulfate electrolytes and the products of concentration of hydrogen ion and free water is linear. Accordingly, the conductivity of acidified copper sulfate electrolytes increases with an increase in sulfuric acid concentration and decreases with an increase in copper concentration.

Jan 1, 2003

By B. Elevli

The aim of this paper is to demonstrate the implementation of multicriteria analysis in selection of the most suitable underground ore transport system for a chromite mine in Turkey. The related problem includes five possible ore transport systems and six criteria to evaluate them. The adopted evaluation and ranking method for this study is PROMETHEE. PROMETHEE I revealed a partial order of alternatives where incomparability exists. PROMETHEE II gave the absolute ordering of alternatives. The results have shown that the PROMETHEE method can be successfully used in solving mining engineering problems. Keywords: multi-objective, decision analysis, mining, ore transport system

Jan 1, 2004