Search Documents

By Jean Habimana

The Detroit Upper Rouge Tunnel CSO Control Project will capture and store up to 201 MG of combined sewer overflow from 28 outfalls in Detroit, Dearborn Heights and Redford Township during wet-weather events. The history of rock tunneling in the area is associated with high groundwater inflows, artesian pressure, and hazardous and combustible gases. This paper presents the geotechnical considerations for designing the 11.28-km (7-mile) long, 9.14 m (30-ft) finished diameter tunnel and its associated adits, chambers and shafts, including the discussions of geotechnical investigations, rock mass characterization, estimated groundwater infiltration during construction, and the selections of excavation methods and lining system based on anticipated ground behavior to be encountered.

Jan 1, 2008

By Shuo Zhang, Wenying Liu

"In dump leaching, the efficiency of metal extraction from ores is strongly influenced by the mechanisms of fluid flow. Particle size distribution acts as a fundamental parameter in the determination of fluid flow properties in packed ore beds. In this study, we investigated the particle size distribution in dump leaching by using image analysis technique. The results showed that the particles in the dump varied from smaller than 2 cm to larger than 200 cm in diameter. P80 was calculated to be 200 cm, which was significantly higher than the historical data used by the operation. P25, P50 and P80 were found to increase non-linearly with increasing depth towards the toe of the dump, suggesting the segregation of fine and coarse particles. The image analysis results were verified by applying the rock fragmentation models. The model with the Swebrec function was found to be in better agreement with the image analysis results. Future research will investigate the effect of particle size distribution on the behaviour of fluid flow.INTRODUCTION Fluid flow plays an essential role in the extraction of valuable metals using heap/dump leaching (Amos et al., 2009). The rates of the chemical leaching reactions and microbial activities determine metal concentrations in the leachates and therefore the efficiency of the metal extraction. The reaction rates are influenced by two fundamental processes: transport phenomenon and reaction kinetics (Bouffard & Dixon, 2001). The transport phenomenon refers to the percolation of fluids through channels and pores in a packed ore bed, which carries lixiviants and reaction products to/from ore surfaces by convection and diffusion. The percolation rate of the leaching solution is determined by the hydraulic conductivity of the packed ore bed, which is a function of the permeability and the degree of saturation (Guzman et al., 2008). Permeability, an intrinsic property of a packed ore bed, is strongly influenced by the particle size distribution of the ore grains (Bouffard & Dixon, 2001). Hence, the objective of this study was to investigate the particle size distribution in dump leaching."

Jan 1, 2017

The great additional clue given to professional books by adequate alphabetical and analytical indexes has been recognized from the beginning in the publication of the Transactions of the American Institute of Mining Engineers The bust ten volumes, edited by Dr Thomas M Drown, the secretary, were provided with indexes, as well as tables of contents Moreover, he included in Vol V (published in 1877), a consolidated index of Vols I to V , inclusive, and, at the triune of his resignation in 1884, he had prepared a similar index of Vols I to X , inclusive, which was published in the following year The indexes of the annual volumes from Vol XI on were made much more extensive than their predecessors Casual mentions, as well as important discussions, were included, the geographical localities of mines of works alluded to in the text were added in the index, and numerous cross-references were introduced, with the purpose of making it easy for the student to discover at once what the Transactions contained, either of thorough treatment or of hints and clues to further inquiry, concerning any topic, locality, or person within their scope In order to extend the advantages of this larger scheme to the earlier volumes a consolidated index of Vols I to XV , inclusive (published in 1888), was prepared by compiling the several annual indexes and introducing additional items for those preceding Vol XI Vol XX , issued in 1892, contained a similar consolidated index for Vols XVI to XX , inclusive, in 1897, a sepal ate index-volume, covering Vols XXI to XXV, inclusive, was published, and on 1902 appeared another for Vols XXVI to XXX These four indexes, for Vols I to XV, XVI to XX, XXI to XXV , and XXVI to XXX, respectively, bound together into a book of about 950 octavo pages have constituted for the last five year s a consolidated index to the Transactions which they cover-with the single difference that the book had to be consulted four times, where a single comprehensive index would require to be consulted but once This disadvantage, however, was relatively small, compared with the great convenience of finding by four trials m one book what would otherwise call for 30 separate searches in 30 books Moreover, the possession of the one might be most useful to a student who did not possess the 30, by indicating to him what they con-

Jan 1, 1907

By Robert S. Mayo

Tunneling, for transportation, began in France with the Milpass Tunnel on the Lanquedoc Canal in 1680. Of course, the ancient miners had been driving tunnels in search of minerals since the dawn of history but this Milpas Tunnel was the first tunnel exclusively for transportation. In England in 1760, the Duke of Bridgewater opened a canal from his coal mines to Manchester, 10 1/2 miles away. At the mine, he drove a tunnel into the mountain so that the miners could shovel the coal directly into canal boats. James Brindley, an untutored genius, was his engineer and this whole transportation system was an instant success and very profitable through the years. Within a dozen years the Duke, again with James Brindley, opened up the Grand Trunk Canal, 139 miles in length with five tunnels. There was one major tunnel on this system, the First Harecastle Tunnel, 1 1/2 miles in length. But this tunnel was too small. It was only large enough for one 7-ft wide boat which had to be "legged" through by boatmen laying on their backs. By 1824 a second tunnel was driven parallel to the first one, but it had a towpath through it for horse haulage. This was the beginning of the " Industrial Age" and tunnels became a very important part of that era.

Jan 1, 1979

By A. J. Opinsky, J. L. Orehotsky, L. L. Seigle

TUNGSTEN incandescent lamp filaments possess a typical structure of elongated crystals generated upon heating the silica-alumina doped wire rapidly to 2200°C or above.&apos; It is known that these very long grains exhibit a preferred orientation, but there is disagreement in the literature about the direction. Rosi,2 and later Rieck; reported that the <135> direction of the large grains in doped wire tends to be parallel to the wire axis, but other investigators have reported that <110> is the preferred direction. Some further investigation of the orientations of large grains in tungsten wire is reported in the following. In the first series of experiments, 6-in. lengths of wire were heated rapidly in a bell jar. Current was passed through the wires and within 15 sec the wires had reached the grain coarsening temperature. 2 min was the annealing time. Wires were heated in hydrogen, nitrogen, and vacuum. Later, wires were heated in an evacuated tube furnace in which the tube was brought from 1000°C to the operating temperature within 25 sec and held 5 min at temperature. Temperatures were measured with an optical pyrometer. After heating, the wires were electro polished and etched, and the orientations of the large grains determined by the Laue back-reflection technique. Most of the experiments were carried out on a single spool of 5-mil silica-alumina doped wire, but a few tests were made with 5-mil thoriated tungsten wire and 10-mil undoped wire. 5-mil silica-alumina doped wires were reduced to smaller diameters by electropolishing for one series of experiments. Orientations of the large grains in silica-alumina doped wire heated in various atmospheres are presented in Figs. 1 and 2 as plots of the direction of the wire axis relative to the cube axes of the crystals. For most of the conditions studied, the preferred orientation cannot be described as a single direction, but the points might be said to group themselves about the arc passing through <110> and <113>. This arc is the trace of the (211) planes and contains the <135> and <124 as well as <011> directions previously observed by other investigators. The preferred orientation of large crystals in silica-alumina doped tungsten wire might be most generally described, therefore, by stating that a (211 ) tends to be parallel to the wire axis. This is true also for wires reduced in diameter by etching and furnace heated, Fig. 2, i.e., the recrystallization texture is apparently unchanged upon removal of the outer layers and substantially independent of the temperature gradient within the wire.

Jan 1, 1962

By X. J. Guo, Q. K. Wang, S. P. Zhong

With depletion of traditional clean copper reserves and fast expansion of the global copper demand and smelting capacity in the past decade, more and more copper smelters have to treat copper concentrate with increasing content of complex arsenic-bearing minerals. Developing economically viable and environmentally reliable methods and approaches for arsenic control in copper smelting has become more critical for sustainable growth of the copper industry. This paper will report the recent effort of Zijin Mining Group Ltd. in developing processes for improving arsenic control and management in the Zijin Copper Smelter. The arsenic distribution and balance data for matte smelting, converting and refining operations in Zijin Copper Smelter is reviewed for understanding of the current challenges in arsenic control. The processes developed for treating the arsenic bearing waste acid bleed stream from the smelting-converting off-gases wet cleaning circuit and the arsenic sludge produced in the refining electrolyte purification circuit for arsenic disposal are discussed. INTRODUCTION With fast expansion of the global copper smelting capacity to meet the world copper demand and depletion of traditional clean copper reserves, more and more copper smelters have to treat copper concentrate with an increasing content of complex arsenic-bearing minerals. China is the world largest copper consumer and also has the largest copper smelting and refining capacity, but majority of its smelting capacity relies on supply of imported copper concentrate. In order to meet the increasing copper demand and ease the tight supply of clean copper concentrate, the Chinese copper industry has to look at the domestic opportunity of developing non-traditional copper resources, specifically those of lower grades, more complex mineralogy, and increasing level of deleterious elements especially arsenic and also process imported copper concentrate with increased arsenic content. Due to a significant and growing environmental issue associated with arsenic contamination, developing economically viable and environmentally reliable methods and approaches for arsenic management and control in unlocking the maximum value of such arsenic bearing copper resources has become more critical for sustainable growth of the industry.

Jan 1, 2019

By W. K. Sawyer

In this Bureau of Mines investigation, one-and two-dimensional gas reservoir simulators were combined in such a manner that pressure distributions both in an induced vertical fracture and in the surrounding formation, could be determined as a function of time for any specified well production rate. The technique used consisted basically of the alternate ust of one-and two-dimensional algorithms for obtaining new pressure distributions in the fracture and in the reservoir, respectively. The pressures at adjacent reservoir and fracture nodes were used to calculate flow rates from the formation into the fracture, which provided source terms for both algorithms. The combination model developed provides the only known means of simultaneously simulating transient gas flow in a vertical fracture and the surrounding formation. Thus, the technique developed would be useful in locating wells in a gas storage field in that the effects of both fracture length and conductivity could be considered prior to drilling and fracturing operations. In addition, it will be helpful in analyzing pressure drawdown tests in a vertically fractured gas well since the entire test can be readily simulated for a wide range of reservoir and fracture properties.

Jan 1, 1974

By G. Potts, K. Raiber, T. BoBo

Effective control of balling line circuits is a problem taconite companies have been dealing with for over thirty years. The sensitivity of balling circuits to changes in moisture, bentonite, concentrate particle size, and other operating parameters are the main reasons for control problems. This paper presents test results and describes the integration of existing instrumentation with a digital image analysis system on a balling circuit. This work has the goal of developing control strategies to automatically adjust water spray and bentonite addition, to optimize the size distribution on the roll screen and reduce the variability in control between balling attendants, resulting in more consistent greenball product quality.

Jan 1, 2003

By Romeo S. Jurani

Yucca Mountain, located in Southern Nevada approximately 160 krn northwest of Las Vegas, is currently the site of intensive surfacebased and underground investigations. The investigations are required to determine if the site is suitable for long term isolation of the Nation&apos;s high level nuclear waste inventory. A major component of the program is the Exploratory Studies Facility, or ESF. The ESF, when completed, will consist of approximately 25,600 meters of tunnels and drifts. The network of tunnels and drifts (Figure 1) will house and support a wide array of testing programs conceived to provide physical information about the site. Information on geologic, geomechanical, and hydrologic data will be used in the repository design if the site is found suitable. Besides a few special requirements, the general ESF ventilation criteria during construction are similar to that of commercial tunneling and mining operations. The minimum air velocity at the Tunnel Boring Machine (TBM) and other active mining faces is 0.51 meter per second (m/s) (100 feet per minute [fpm]). Airways, estimated leakages and ventilation controls are converted into equivalent resistances for input to mine ventilation network computer simulations. VNETPC Version 3.1 computer software is used to generate the ventilation models for optimized system design and component selection. Subsequently, actual performance of the ventilation system will be verified and validated to comply with applicable nuclear regulatory quality assurance requirements. Dust control in the ESF is dependent on effective dust collection, enclosure, and airflow dilution. Minimum use of water, as feasible, is necessary to avoid adding moisture to the potential repository horizon. The limitation of water use for test drilling and TBM operation, and the rigid compliance with applicable federal and state regulations, make the ESF a ventilation design challenge.

Jan 1, 1995

By J. Stoll

In May 1998, Hanson Aggregates Midwest, as an outcome of mine planning, offered a 10-acre tract of land containing the famed fossil-bearing Silica formation, to the City of Sylvania, OH. in the form of a 99-year lease agreement. The Olander Park System, and Ohio code park operating within Sylvania Township, was then approved by Hanson and the City to manage and fund the park. All parties signed the lease in August of 1999. In November 2001, local residents voted to fund the park by a margin of 2 to 1. The park will consist of a shallow (approx. 20 ft.) former cement production quarry that is 700 ft. long by 300 ft. wide. Hanson’s motivation and vision for the park was fivefold: 1) the site was located away from long-term reserve access; 2) it would serve nicely as buffer property for the active quarry; 3) it had become an area of illegal dumping by locals in the past; 4) trespassing and safety issues would be limited by allowing supervised usage; and 5) the shallow outcropping contains the world famous, fossil-bearing Silica shale. Hanson will supply shale to the park perpetually via stripping activities in the process of uncovering quality construction aggregate limestone and dolomite reserves. Thousands of enthusiastic fossil hunters have already combed throughout the shale in their quest for “treasures”. The park’s master plan also features nature trails, picnic areas, a fossil-themed play area, amphitheater, visitor’s center and gift shop. Given the natural and people resources that Sylvania Fossil Park will have to offer, Hanson is confident that it will become the premier invertebrate fossil hunting site in the United States. It will also remain a solid community relations vehicle for years to come.

Jan 1, 2003

By D. F. Malan, J. A. L. Napier

A number of shallow coal or hard rock mines employ pillar mining systems as a strategy for roof failure control. In certain platinum mine layouts, pillars are designed to ‘crush’ in a stable manner as they become loaded in the panel back area. The correct sizing of pillars demands some knowledge of the pillar strength and the overall layout stress distribution. It is particularly important to understand the impact of the layout geometry on the effective regional ‘stiffness’ of the rock mass around each pillar. An important design strategy is to model relatively detailed layout configurations which include a precise representation of the local pillar layout geometry and to analyse multiple mining scenarios and extraction sequences to select optimal pillar sizes and barrier pillar spacing. Although computational solution techniques are now impressive in terms of run time efficiency, a major difficulty is often encountered in assigning suitable material properties to the pillars and in devising an effective material description of the layered rock strata overlying the mine excavations. This paper outlines an efficient numerical strategy that can be used to assess large-scale pillar layout performance while retaining the ability to modify individual pillar constitutive behaviour. The proposed method is applied to selected layouts to compare estimated average pillar stress values against values determined by detailed modelling and against observed behaviour.

May 3, 2023

By Étienne Yvenou, Martin Désilets

Le procédé d’électroaffinage du Cu est nécessaire pour atteindre les niveaux de pureté requis pour les applications les plus courantes telles que son utilisation comme conducteur électrique ou thermique.

May 2, 2024

By Masakazu Niinae, Tasuma Suzuki, Mai Moribe, Yohhei Okabe

Bench-scale electrokinetic experiments were performed to elucidate the electrokinetic remediation mechanisms of arsenate from artificially contaminated kaolinite. The electrokinetic experiments in which a constant voltage was applied demonstrated that high soil pH favored arsenate remediation with respect to both the remediation time and electricity consumption. It was also demonstrated that applying a pulse voltage (1 hour ON, 1 hour OFF) significantly improved the electricity consumption efficiency when the soil pH was maintained at the initial value during the experiments; this trend was not observed when the soil pH was gradually increased from the cathode side. These electrokinetic experimental results indicate that the remediation rate-limiting step varied with soil pH. When the soil pH was maintained at the initial value of 7.2 during the experiments, arsenate desorption was the remediation rate-limiting step rather than the migration of dissolved arsenate toward the anode. Conversely, when the cathode pH was not controlled and the soil pH was correspondingly increased gradually from the cathode side, the migration of hydroxyl and desorbed arsenate ions toward the anode played a more important role in the control of the overall remediation efficiency.

Jan 1, 2014

By J. P. Wilson

The Tessenderlo-Kerley Leach process has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia and ammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By Javier Casas, Richard Corsino, Miguel Baylon, Miguel González

El presente trabajo consistirá en presentar la metodología realizada para la inyección de cianuro a presión en el pad 1A, la cual contempla la realización de estudios de las condiciones del pad, barrenación de los pozos de inyección y de monitoreo, realización de pruebas metalúrgicas, inyección de cianuro a presión, monitoreo geotécnico en la inyección, y finalmente los enjuagues realizados. Finalmente se presentarán los resultados obtenidos de las onzas de oro y plata recuperadas de esta prueba piloto y los planes futuros que se tienen acerca de estos trabajos.

Sep 30, 2022

By Jose Castro

The growing demand of scrap to supply the electric arc furnace has driven to search for new alternatives of raw material. The DRI produced using self-reducing pellets has become competitive due to the potential use of a wide range of carbonaceous materials such as coal, charcoal, biomass etc. In this context, the rotary kiln process using improved technologies such as post-combustion and self-reducing burden is a promising source of high quality raw materials. This paper presents a mathematical model of the rotary kiln process designed for self-reducing pellets and post-combustion. The model is based on the transport equation of two-phase flow, energy and mass transfer. The solid material is composed of a typical self-reducing pellet. The model considers the solid phase (C, volatiles, Fe2O3, Fe3O4, FeO, Fe, H2O, SiO2, Al2O3, MgO, P2O5, K2O, Na2O, FeS, CaO and gangue) and the gas phase (N2, O2, CO, CO2, H2, H2O, SO, SO2 and SiO). For each of the above components a conservation equation is solved and the mass and energy transport is accounted. The set of differential equations are coupled by the rate equations describing the kinetics of the several reactions, which take place within the rotary kiln. All the conservation equations are solved based on the finite volume method applied for a three-dimensional cylindrical coordinate system. Simulation results are presented for global parameters such as metallization degree, productivity, gas utilization ratio and calorific value. Inner conditions such as three-dimensional gas and solid temperature patter and compositions are discussed.

Jan 1, 2006

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By J. Zhou1

"The extractive metallurgy of gold ores is largely driven by their grade and mineralogy. The concentration of gold in the crust is extremely low and highly variable, resulting ore variability in many gold and copper-gold deposits. More importantly, gold in an ore may occur in two or three forms (i.e. microscopic gold, submicroscopic gold and surface gold), making gold ore processing extremely challenging. Geometallurgy is a technique to document variability within an orebody and quantify and evaluate the impact of many factors including geology and mineralogy on grinding, flotation, leaching and metal recovery processes. The objective of gold geometallurgy is to reduce and minimize the technical risk in project evaluation, plant design, mine planning and production forecasting through geometallurgical modelling, representative sampling and subsequent systematic mineralogical and metallurgical testwork. Gold deportment study is a powerful tool in characterization of various gold ores. Effective and quantitative gold deportment results are critical and useful for predicting gold recovery and building geometallurgical models of gold ores. This paper provides an overview of geometallurgy fundamentals and applications in gold processing, with a focus being on the ore characterization and gold deportment study.INTRODUCTION Geometallurgy is an inter-disciplinary approach which links the geological, geochemical and mineralogical characteristics to the metallurgical performance of an orebody. Combined with mine planning, it has been used in scoping, prefeasibility and feasibility studies, process design and optimization of gold, copper-gold, copper-moly, nickel and iron projects among others (Williams & Richardson, 2004; Dobby, Bennett, Bulled, & Kosick, 2004; Bulled, 2007; Bulled, Leriche, Blake, Thompson, & Wilkie, 2009; Kormos, Sliwinski, Oliveira, & Hill, 2013; Muinonen, Sciortino, Korczak, & St-Jean, 2013; Leichliter & Larson, 2013; Leichliter, Jahoda, & Montoya, 2013; Hatton & Hatfield, 2013; Baumgartner et al., 2011, 2013; Hoal, Woodhead, & Smith, 2013; Zhou, 2013). The goal of a gold or copper-gold geometallurgical program is to characterize and understand the metallurgical variability of an orebody, such as comminution, gravity, flotation and cyanidation parameters and metal recoveries, and to build a geomet model which can be used to assist in mine planning and to predict the plant performance. In any geometallurgical program, representative sampling is the key to ensure the results of a geometallurgical study will reflect future performance once the plant is commissioned. Geometallurgy compliments, but does not replace, the traditional mineralogical and metallurgical approach during the development and operation of a gold or copper-gold project. Geometallurgy is a methodology for testwork design and a framework for mine planning. The first part of this paper provides an overview of geometallurgy fundamentals and application in gold ore processing."

Jan 1, 2017

By Lex B. Golden

The purpose of this investigation was to evaluate the corrosion properties of certain alloys of titanium and to compare them with those of unalloyed titanium. Such information should make it possible to determine the desirability of substituting these alloys for commercially pure titanium in certain applications. Titanium-manganese, titanium-chromium-iron, and titanium-vanadium-iron alloys, with 2 types of unalloyed titanium, I consolidated by arc melting and the other by powder-metallurgy techniques, were included in the study. Tests were carried out in sulfuric, hydrochloric, phosphoric, nitric, and mixed acids and in chloride solutions. All solutions were saturated with air.

Jan 1, 1957

The need for the hydraulic transportation of coal in the New South Wales coal industry, both from the coal face to the surface and from the coal mine to the consumer or the port for export, is explained. Details of research projects currently in&apos;progress and involving the hydraulic transportation of New South Wales coals are given together with information on the hydraulic transportation of coal in the United States of America.The potential of hydraulic transportation as a viable alternative to the proposed expansion and upgrading of the New South Wales railway system to meet the projected New South Wales coal production to the year 2000 is described.

Jan 1, 1980