Search Documents

By Nii Allotey Odunton

One of the primary responsibilities of the International Seabed Authority?s Secretariat (the Secretariat) is to assess the quantities of metals present in seabed polymetallic nodules in the International Seabed Area under the Authority?s jurisdiction. To carry out this responsibility, the Secretariat periodically undertakes an assessment of the reserved areas in the Clarion-Clipperton region of the northeastern Pacific (CCZ) using the data submitted by the registered Contractors and maintained in the Authority?s POLYDAT database. The results of its most recent assessment demonstrated that the information submitted by the Contractors, though satisfactory for some purposes, does not permit the in situ quantities of metals in these areas to be estimated with a degree of confidence that is comparable to many land-based mineral resource estimates. Our strategy is to divide the work into two distinct but closely related efforts; one to draft a Prospector?s Guide that provides a narrative description of the key geological and oceanographic data that may be related to deposit abundance and metal content, and another that we call the Geological Model, that summarizes and documents the quantitative resource assessments accomplished in the project.

Jan 1, 2005

By C. Sampaio, C. Petter, M. Veras

"INTRODUCTION Use of sensor technology applied to the gravimetric beneficiation is intended for the selective preconcentration or separation of various minerals. Sensor Based Sorting (SBS) uses sensors to identify the particles and separate them by a mechanical process (flap) or pneumatic ejection valves (Wotruba et al. 2014). The principle of the SBS technology to separate mineral particles consists of three phases which cover feed,detection and separation. (killmann, 2009 Apud nienhaus et al. 2014). The applicability of the technique in an early stage of beneficiation enables free particles and poor grade to be a part of the process. The mass of tailings to be processed can be removed at the initial stage to save energy, water and equipment maintenance (Wotruba et al. 2014). Lindner (2010) suggested that the use of SBS technology would only will be possible if there exsists an electromagnetic interaction in all the wave spectra interacting with the solid ore. The interaction of electromagnetic waves depends directly on the characteristics of the material. The material receives a spectrum of electromagnetic waves by irradiation and this results in a reduced wavelength with differing types radiation such as fluorescence, reflection, remission, absorption, transmission and transmission. The frequency of the wave spectrum varies between 1000 and 1020Hz, illustrated by the data in Figure 1, which shows that each type of sensor emits a wavelength inversely proportional to the frequency ranging from 10-11pm to 104km, and the frequency that varies between EHz 103 and 1020kHz. The difference between the electromagnetic spectrum variations can only be visible to the human eye at wavelengths with intervals between 380nm and 780nm (Wotruba et al. 2014). One of the main advantages of operating with imaging sensors is the versatility of the images which can take on zero, one, two or three dimensions shown below as a point, a line, an area or a spatial image, as illustrated in Figure 2. According to Schubert (1988), to separate a mineral particle it is necessary to follow the characteristics of mineralogy, physics and chemistry with or without use of water. The use of new technologies can help reduce operating costs and improve utilization of mineral resources."

Jan 1, 2016

By D. L. Johnson

A number of small but rich copper sulfide (chalcocite) ore deposits are located on Michigan's Keweenaw Peninsula. These deposits are considered too small to warrant the capital investment required for conventional mining. However, they are being considered for in-situ solution mining as a way to revitalize the area's once prosperous copper extraction industry. Geology, mineralogy and geohydrology of the deposits have been investigated to determine their suitability for leaching; Three conclusions were drawn from the work. First, the sulfide mineralization is found primarily in fractures (65%) and, therefore, is accessible to injected leach solutions. Second, the ores are shallow, occurring from surface exposure to about 200 meters depth; injection and recovery wells would not have to be excessively deep. Third, the rock was found to have low permeability, in the neighborhood of thirty millidarcys or less. However, preliminary hydraulic fracturing experiments indicate that this will be an effective method for permeability enhancement. In one experiment a permeability increase of 100 times was achieved using a very low injection pressure at shallow depth. Additionally, fracture aperture spacings measured from drill core were correlated with fair success to field permeabilities.

Jan 1, 1989

By Roy A. Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a superior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

By Anup Kumar Mandal, Sanjoy Chowdhury, Biswajit Das

"Tailing pond of an iron ore mine necessitated raising the height of its embankment to create additional storage capacity. The tailing pond is located in eastern India and raising the height of embankment was going on during the month of January, 2014. Upstream method of construction was adopted since there was no space available at the downstream side. During the construction, about 200 m stretch of the north east embankment of height about 5.5 m failed forming a classical slip circle on the upstream side involving about half the top width of the embankment. To find out the root cause of the slope failure, detail geotechnical investigation work was carried out within the embankment as well as in the adjacent areas within the pond. About 7.5m thick very soft tailings were detected below the constructed embankment. Shear strength of the soft tailing was very low and was inadequate to sustain imposed embankment load. This resulted in the failure of the embankment. Analysis of the tailing deposit revealed that even after failure, settlement was continuing due to imposed embankment load. Under normal onedimensional consolidation, the tailing deposit would have taken about 5.7 years for 90% of primary consolidation. However, in order to mitigate the scarcity of storage space, mining plan required raising the height of the embankment within next six to eight months. Therefore, despite the fact that there was a failure, it was necessary to continue the construction on the underlying weak stratum. The system was redesigned with installation of prefabricated vertical drains (PVDs) to accelerate the consolidation process thereby gaining the in-situ strength. Strength was additionally enhanced by installing geogrids in multiple layers. It stabilized the existing embankment and also ensured construction of additional height over and above the existing embankment.INTRODUCTIONBeneficiation plant in the Iron mines enhances the mineral content by separation of contaminants and fines. The residue (waste material) is called tailings/tailings depending upon the grain sizes. These tailings in a slurry form are generally disposed in a pond called as tailing pond/tailing pond. Height of embankment of such ponds is increased either by upstream or by downstream or by centrally raising methods in different phases as quantum of deposition in the pond increases with time."

Jan 1, 2015

By L. A. Roe

Magnetic separation of iron ores is one of the fastest-growing segments of the minerals beneficiation industry. The tonnage of taconite ores processed annually by magnetic separation will, in a few years, reach 100 million. Magnetic separation occupies an attractive position in the field of ore beneficiation. It is a simple yet effective method, used for some 150 years and steadily growing more important. This type of beneficiation orginated in 1792, when William Ful-larton was issued a British patent covering the separation of iron ore by magnetic attraction. What is magnetism, and why are some materials capable of being magnetized and others not The study involves many unknowns, and even a partial answer to these questions would be a dissertation in solid state physics and perhaps other fields of science. But the last two decades have revealed basic facts as to why certain materials are magnetic and what happens to them when they are magnetized. Some of the newer studies in solid state physics have developed a theory that can be applied to studies of magnetism. It is claimed that magnetism stems fundamentally from the spin of electrons in atoms that tend to go in pairs, spinning in opposite directions. The atom as a whole can act as a magnet only when there is an imbalance of electronic spin. Whenever an atom has an odd number of electrons, therefore, this imbalance exists. This neutralizing effect explains why a piece of material that contains atomic magnets is not necessarily magnetic. The physicists tell us that iron is composed of many small magnetized regions called domains, which consist individually of millions of atoms. The piece of iron becomes magnetized when an external force lines up these domains in the same direction. Fundamental data developed by physicists working in fields far removed from minerals beneficiation are now available for developing better magnetic separators for ore processing. More Data Needed on Magnetic Properties of Minerals: There is less information on magnetic properties of minerals than there is for certain aspects of magnetic separator design. When the data on magnetic properties is available, it is often directed toward the study of powders for tape recorders and other highly scientific endeavors that are of little use to the beneficiation engineer. W. R. Crane's table of tractive forces, published in 1902, is still a guide in the study of magnetic minerals. Bits of other information regarding electrostatic conductivity, dielectric constant values, and permeability of various minerals have also appeared but are of small practical value in magnetic separation of ore. It is extremely important to obtain pure mineral specimens for making investigations and to record results that may be of use in studies of magnetic processes. Reference to the large volume of data developed by those concerned with analysis and design of permanent magnets soon reveals that these people have extensively evaluated the effect of various impurities on magnetic properties. Much of the science of the ferrite industry is based upon spinel-type structures which are varied by substitution of selected elements or even subtraction of elements, leaving vacant sites in the space lattice. Magnetic separators are used to beneficiate a wide variety of industrial minerals. In this application the relatively large volumes of nonmagnetics are usually the commercial products. The amount of mag-

Jan 1, 1959

By Robert Martinez

A proven high grade reserve of gold mineralization located in Mexico is evaluated to determine which gold recovery process is best suited for this deposit. The processes evaluated are; Heap leaching, Vat leaching and a CIP circuit. All qualify as viable options, however each one presents a different economic picture which is impacted substantially by the financial constraints of the project. Taking this into consideration the most economic process was selected.

Jan 1, 1987

By R. G. Clay, C. F. Seaman

THE mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that time, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered, the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. ORIGINAL EQUIPMENT AND INSTALLATION A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots and the up position would connect it to the line from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1942

By K. N. Hebbar, R. G. Reddy

Spent potliners (SPL) were declared hazardous waste under RCRA (K088) in July, 1990. The glass formation characteristics of the SPL was studied. The SPL glassy matrix were analyzed using X-ray diffraction and optical microscopy. Results showed that SPL can be fixed in a glassy matrix with the addition of sand and limestone. The optimum amounts of additives were determined for obtaining the best glass formation characteristics.

Jan 1, 1995

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

Disruption in critical minerals supply chains has resulted in the evaluation of various types of mineral deposits for critical minerals potential. Much of the study on critical minerals focuses on occurrence and characterization, but little research has addressed what concentrations of critical minerals in a mineral deposit are required to make an exploration target into an operating mine. Understanding the cut-off grades of ore deposits being actively mined is one criterion to determine if concentrations in an exploration target are high enough. Cut-off grade is defined as the minimum amount of mineral contained in a ton of ore that is sent to the processing plant. Among many factors, cut-off grade depends upon the size and type of the deposit and mining operation, the processing technique, and market prices. This research does not aim to define cut-offs for determining if a mineral deposit is economic. Rather, it defines estimates of concentrations of critical minerals that could be considered good enough for further exploration. For example, ~2% total rare earth oxide (TREO) is the cut-off grade for Mt. Pass carbonatite, but 500 ppm TREO could be an exploration target for coals.

Feb 1, 2025

By Robert W. Thomas

LEACHING of mined-out areas at the Arizona property of the Ray Mines Division, Kennecott Copper Corp., was started on Jan. 20, 1.937, and by July 1, 1938, 10,000,000 lb. of copper had been produced by this method. Leaching operations at present are confined to the western portion of the ore body and over an area of approximately ten acres. The ore in this area was extremely high in pyrite and the copper content, which averaged slightly in excess of 1 per cent, was the result of incomplete secondary enrichment by solutions which apparently worked laterally from the main ore body. Above the ore was an unaltered zone of primary or protore averaging 125 ft. in thickness and containing approximately 0.6 per cent copper. Above this was the capping or leached zone averaging 50 ft. thick.

Jan 1, 1938

By Ki Joo Sim, Sung Beom An, Joonho Lee, Minsoo Shin

Valorization of the electrical arc furnace oxidizing slag by coke was carried out by the reduction of iron oxide in the slag. Since the reduction of iron oxide by solid carbon is an endothermic reaction, supply of heat energy is required. In addition, slag has a low thermal conductivity; traditional fuel injection is not suitable for this reaction. Microwave can be used to supply heat energy to the system. Commercial oxidizing slag was reduced by coke under the microwave irradiation (1.7 kW, 2.45 GHz). The maximum recovery ratio of iron was 87%. In addition, slag composition modification was attempted to use the remaining slag for a mixture in cement clinker. Free-CaO in the slag was successfully suppressed, and the use of the remaining slag as a potential mixture was confirmed.

Jan 1, 2014

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZg2, (formerly ASTM No. 17; also known as Dowmetal C or AM26o) which was done under "Restricted" Project NRC-2I, in 1942-1943, and reported in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat- treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZp was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZp, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray 'analysis. From this figure it may be seen that above approximately 375°C (707OF), AZp alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, ancl because of its solubility relations, AZqz resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ² alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1949

By Min-Min Lin, Bing Xie, Hong-Yi Li, Yang Yang

After precipitation of ammonium vanadates from vanadium-containing leaching liquor, vanadium (V(V)) and chromium (Cr(VI)) exist in the waste water in form of vanadate ions and chromate ions. In order to efficiently extract and recover V(V) and Cr(VI) from waste water, an environment-friendly method based on anion exchange was investigated in batch tests using macroporous weak base resin Dex-V. The adsorption conditions optimizes in detail, including the effect of pH, initial metal concentration, resin volume, contact time and temperature. The ion-exchange adsorption process for both V(V) and Cr(VI) showed maximum capacity at pH 3.0 for an initial concentration of 100 mg L−1, and reached equilibrium after about 40 min of contact at 298 K. The maximum adsorption ratio under the optimum conditions for V(V) and Cr(VI) was 98.98 and 99.87%, respectively. Result shows that the established method is a promising alternative for simultaneous extraction of vanadium and chromium.

Mar 1, 2018

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

WITH the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZ92, (formerly ASTM No. 17; also known as Dowmetal C or AM260) which was done under "Restricted" Project NRC-21, in 1942-1943, and reported, in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZ92 was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZ92, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray analysis. From this figure it may be seen that above approximately 375°C (707°F), AZ92 alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a. two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, and because of its solubility relations, AZ92 resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ92 alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1947

By Nicanor Vilchez O

Los ciclones se utilizan para separar partículas sólidas contenidas en un fluído de acuerdo al tamaño y gravedad específica. En ese sentido, el presente trabajo revisa el uso de hidrociclones en operaciones de procesamiento. y señala algunos aspectos de diseño y operación de estos equipos para su correcto empleo en las operaciones de separación sólidos-sólidos.

Oct 14, 1980

By Yuan Lu, Yiming Rong, Richard D. Sisson Jr

With the development of quench technology, there is a trend of using gas quench to replace liquid quench for less distortion and residual stress. The fundamental difference between the liquid and gas quench is the heat transfer coefficient, not only the values but also the shape of the curve as a function of temperature. The equivalent heat transfer coefficient for the liquid and gas quench is analyzed by simulations and experiments. Even it may result in the same hardness in the liquid and gas quench, the steel microstructure may be different because of the different cooling processes, and therefore other steel properties, such as toughness, may be different. The cooling process, microstructures and properties such as hardness and toughness should be examined when designing the liquid or gas quench processes.

Jan 1, 2015

Jan 1, 1929

By Evan Bennet

El presente texto señala la situación del carbón en el valle del Santa, al tiempo que busca reivindicar su posición, producción y demanda del mismo. Para ello, el doctor Fraser describe las características del mineral, encontrando que el carbón del tipo "La Limeña" contiene una elevada gravedad y friabilidad, como un buen porcentaje de los "middlings". Posteriormente se realizaron pruebas como la del carbón R.O.M. en una planta Bradford improvisada, demostrando que el carbón y los "middlings", se trituran fácilmente gracias a la friabilidad del mismo y que el producto de tamaño mayor puede ser escogido a mano fácilmente para su disposición futura. Mientras que las pruebas de diversas clases de "middlings", evidencian dificultad en el tratamiento para la recuperación de carbón puro, pues el triturado a tamaños finos libera sólo pequeñas cantidades de carbón "float", manteniéndo su calidad inferior en comparación con los finonaturales, que se trituran fácilmente del R.O.M. y del producto de la planta Bradford. De otro lado, se describe el beneficio del carbón en las minas, la conservación de maquinaria, uso de briquetas, el empleo del ferrocarril como transporte y las instalaciones de las plantas lavadoras del banco minero en Chimbote y planta pallasca en Chimbote.

Jul 20, 1956

By M. Bryson, S. Broom-Fendley, A. E. Brady, W. Dawes, G. Beer, N. Sehlotho, S. Al-Ali, F. Wall

The Songwe Hill Rare Earth Element (REE) Project in Malawi is a near surface carbonatite-hosted deposit with synchysite and apatite as the key REE bearing minerals. A strong focus has been placed on understanding the REE mineralogy of the Songwe Hill carbonatite as REE mineralogical characterization is a crucial component at all steps, ranging from exploration to production, in the development of REE deposits. Extensive mineralogical work has been completed at Camborne School of Mines (CSM), Natural History Museum (NHM) London, British Geological Survey (BGS), Nottingham, Aberystwyth University, Wales, Mintek, South Africa, and SGS Inc. Canada (SGS). The following analytical techniques were used: scanning electron microscopy (SEM), electron microprobe analysis (EMPA), laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), and QEMSCAN®. The detailed studies have demonstrated that while synchysite is light-REE enriched as expected, apatite, abundant in all stages of carbonatite emplacement at Songwe, is anomalously enriched in mid- to heavy-REE relative to apatite in other carbonatite deposits. The distribution of REE within synchysite and apatite at Songwe has had important implications for the direction of the metallurgical work with respect to the behaviour of light and heavy REE through the flotation and hydrometallurgical stages of the flow sheet.

Jan 1, 2014