Search Documents

By Joseph Jensen

MANY fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which the field was developed. In contrast thereto, in the Ventura Avenue Field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other that the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 ft. of oil-bearing zone has been penetrated below this intermediate w9ter-a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater the penetration in the zone, the better the well. The error of this assumption became evident

Jan 1, 1930

By James R. McVey

Tests during pillar robbing, longwall operations, and other mining activities indicate that roof-floor convergence rates can be used as an indicator of imminent roof failure. A large number of electrical-mechanical devices have been built to measure convergence as well as convergence rates, but most obstruct mine traffic and are costly and time consuming to install. The Bureau of Mines has designed and is evaluating three types of small ultrasonic units to make these measurements. The new instruments provide nonobstructing measurements up to 35 ft away. The ultrasonic transducers can be attached to a roof bolt, placed in an unsupported area (by means of a toss basket), or handheld. Total distance to the target and rate of closure are displayed digitally to 0.001 ft and 0.01 ft/min, respectively.

Jan 1, 1984

By E. T. Hunter

Surrounded by the 13,000-ft high peaks of the San Juan Mountains in southwestern Colo., the town of Silverton is the site of the extensive development operations initiated 20 months ago by Standard Metals Corp. Appropriately termed the Silverton Project, Standard's operation has now passed the half-way point in its program to reopen two mines that were once sizeable producers of copper, lead, and zinc ores.

Jan 1, 1961

By R. Karl Zipf

A fatal explosion in a sealed area at the Sago Mine in 2006 prompted researchers and regulators in the United States to re-examine the requirements for explosion-resistant mine seals. Seals are used in underground coal mines to isolate abandoned mining areas from active workings. Prior to the Sago disaster, mining regulations required seals to withstand a 140 kPa explosion pressure. Recent research at the National Institute for Occupational Safety and Health (NIOSH)Pittsburgh Research Laboratory showed that pressures from explosions can far exceed this pressure. U.S. mining regulations now require much stronger seals. Current research focuses on understanding the science, engineering and management of sealed areas of coal mines. Scientific efforts seek understanding of how explosive methane-air mixtures accumulate using measurements and models of the sealed area atmosphere. Additional scientific efforts aim to understand the explosion pressures that can develop using a combination of numerical modeling and experiments. Engineering efforts aim to produce design guidelines for seals that can resist the new higher pressure design criteria. NIOSH researchers are also developing guidance for monitoring of sealed area atmospheres and inertization of potentially explosive gas mixtures within sealed areas. This paper seeks to encourage scientific discussion among international peers since preventing explosions within sealed areas is of interest to underground coal operators and regulators.

Jan 1, 2009

By G. H. Long, D. H. Magnusson

THE DEFINITION of the continental margin, as considered in this paper, is in the broad sense: " ... those provinces of the continents and of the oceans which are associated with the boundary between these two first-order features of the earth" (Heezen et aL, 1959, p. 17). The provinces in the area under con-sideration are: the Continental Shelf, the Continental Slope and the Continental Rise. The Continental Shelf extends from the shoreline to the shelf break, which lies at approximately the 200-meter isobath through-out the region (except north of the Grand Banks, where the break may be defined more properly by the 400-meter isobath). The Continental Slope and Rise occur between the shelf break and the 4,000-meter isobath. (The last figure was somewhat arbitrarily selected for the purpose of this paper.) The Atlantic Continental Margin as thus defined extends along the eastern coast of Canada from the International Boundary in the Gulf of Maine northward to approximately the 60°N latitude off the coast of Labrador. The area of study amounts to at }east 500,000 square miles -an area roughly equivalent to 13 per cent of Canada's total land surface.

Jan 1, 1970

By Jonas Addai-Mensah

Despite the fact that nickel (Ni) laterites accounts for about 60 % of the world?s nickel mineralization, commercial processing of complex, low grade Ni laterite ores by conventional beneficiation (e.g. magnetic, electrostatic and flotation separation) still presents intractable challenges, particularly in heap leaching. Invariably, low grade laterite ores require aggressive hydrometallurgical techniques (e.g., highly acidic lixiviant leaching at ambient or elevated temperatures) for Ni and cobalt (Co) extraction. As a precursor to heap leaching, agglomeration of the multi-mineral phase feed particles into robust and porous granules of 4-10 m permeable bed, is essential. In the present work, several basic and applied studies of the agglomeration behavior of real Ni laterite ores and selected oxides and clay minerals (hematite, quartz smectite and kaolinite) which constitute the predominant host gangue phases of typical laterite ores are performed. Isothermal, batch agglomeration tests involving sulphuric acid solution as a binder were carried out to produce coarse, narrow-sized (5 ? 40 mm) granules which were well characterized. The influential role of feed ore characteristics (e.g., mineralogy/chemistry and primary particle size distribution) and binder composition (30 vs. 44% w/w H2SO4) and dosage (15-25 wt.%) in agglomeration behavior and granule properties were examined through several characterization techniques including granule size, compressive strength, bed percolation and re-wetting stability and 3-dimensional micro-structure analyses. Links between feed mineralogy/chemistry and size, binder formulation, agglomeration behavior, curing conditions and final granule properties and structural characteristics are established. The implications of the findings to Ni laterite plant agglomeration for enhanced heap leaching are discussed. Keywords: nickel laterite, complex low-grade ores, agglomeration, heap leaching, micro-structure

Sep 1, 2012

By Merline W. Van Dyke

The Surface Mining and Reclamation Act of 1977, PL 95-87 (The Act) granted the Office of Surface Mining (OSM) the duty of collecting fees from the active coal mining activities to be used in abating the hazards associated with abandoned coal mines. Since the passage of the Act, OSM has been instrumental in closing a multiple of mine hazards and in full cooperation with the states involved. Complete mine closures range from simply filling a subsidence hole to exodic designs costing thousands of dollars, such as in the case of the Portal Park swimming pool in Colorado Springs, Colorado. The Portal Park olympic sized swimming pool was built over an abandoned coal mine by a group of local citizens and given to the city of Colorado Springs. This pool receives the largest number of users each year. During the past four years, OSM has abated six mine related hazards in and around the pool. During the summer of 1982, the pool started tipping causing the pool waters to run out the west end. This pool tipping and the associated cave-in problems caused great concern to the city and the local users. This citizens concern generated a request from the city for OSM to assist in checking out the pool problems. Early in 1983, OSM initiated a driling program to investigate the subsurface voids. This drilling effort revealed several large voids within a few feet of the pool deck, with all voids inundated with ground water. Therefore, the void filling method favored the hydraulic backfilling needed to be confined to the area under the pool. This confining problem lead to the development of the gravel bulkhead cutoff walls to confine the backfilling effort to the areas under the swimming pool.

Jan 1, 1985

By Wesley A. Grosh

The Allah Cooper mine, in Louisa County, Va., formerly was a producer of lead and zinc. It was believed that the critical shortage of leach and zinc and the fact that some ore had been produced at this mine justified exploration of it. A preliminary examination was made on April 30, 1943, by J. E. Hill, a Bureau of Mines Engineer. Diamond drilling was done on the property from November 30 to December 18, 1943, to determine whether the sulfide body extended to depth. One hole drilled to a depth of 650 feet and located so as to cut the Allah Cooper ore shoot about 150 feet below the lowest known mine workings failed to disclose sulfide vein at that depth.

Jan 1, 1949

By D. Z. Wei

Amine collectors with different structures and length of carbon-chain have been widely used in oxide minerals flotation. In this paper, we synthesized one kind of binary amine, N-dodecylethyl- enediamine, and studied its flotation performance. From the results, we can see N-dodecylethylenediamine which has excellent frothability, is a new type of chelating surfactants. And it also has fine catchability to quartz and hematite. The recoveries of quartz and hematite increase with the augment of N-dodecylethylenediamine concentration. When the dosage of collector reaches 100g/t, the recoveries of quartz and hematite achieve 95.30% and 87.89% respectively. Meanwhile, the influence of pH on the flotation recovery of hematite is studied and test results showed that, as pH increases, the flotation recovery rises until pH=9. And the recovery reaches its maximum in alkalescence. The collector has better flotation capability to quartz than to hematite. And the maximum recovery of quartz is gained in alkaline media, which reaches 97.87%. Finally, the flotation mechanism of N-dodecylethylenediamine is discussed through the measurement of infrared spectroscopy.

Jan 1, 2014

By D. G. Westlake

Levine has concluded that prismatic slip in titanium is controlled by two distinct thermally activated processes in the temperature ranges O° to 220°K and 220" to 300°K. We feel that his evidence is not convincing. He has drawn a curve through the plot of activation volume u* vs temperature T with a break at 22WK, Fig. 2. We believe that considering the possible experimental error apd the fact that there are only four points between 4° and 196°K, one could be justified to represent these points by the smooth curve we show as a solid line in Fig. 12. Levine believes that (8rf/aT)+ is discontinuous at 220°K, but he hints that he recognizes the possible doubt. We doubt seriously that the results shown in Fig. 1 indicate a discontinuity at 220°K. Certainly if he were justified in drawing a straight line through only four points on Fig. 2, we are even more justified in drawing straight lines through the seven points between 77" and 297°K on Figs. 1 and 3, because a straight line touches all seven of his circles. If his measurements of t were so precise that his decision to draw two curves in Fig. 3 is valid, then the experimental technique is deserving of further mention. We have drawn a smooth curve through the results in Fig. 3 and used this and the curve in Fig. 12 to obtain the values of shown in Fig. 13. Finding continuous is a contradiction of Fig. 4, which deserves comment itself. Levine obtained the solid circles in Fig. 4 using Fig. 2 and a smooth curve through the points shown in Fig. 3. We have replotted these solid circles in Fig. 14. We submit that there is no basis for his two straight lines (dashed in Fig. 14), and therefore have superimposed the curve that we believe is indicated. Certainly, there is reasonable doubt that a discontinuity in dH/dT exists at 220°K, even when one accepts Fig, 2. Furthermore, if one draws the straight lines indicated by least-squares treatments of the results presented as open circles in Fig. 4, their intersection is at about 196°K, not at 220°K as shown. Thus the alleged agreement between Figs. 3 and 4 with respect to "break" temperatures is not apparent. In Fig. 9, Levine has drawn a straight line very much different from the one indicated by a least-squares treatment. Obviously, he has done this because he recognized that H = 0 when T = 0. He is consistent in drawing the low-temperature curves in

Jan 1, 1968

By Lucia Kuizon

The Antimony RARE II area is underlain principally by Mesozoic igneous rocks associated with the Sierra Nevada batholith. The San Andreas fault zone is near the southern boundary. Metallic mineral deposits are associated with the fault zone. These deposits were formed from magmatic solutions, and tend to be along shears and fractures within the country rock. Marble and dolomitic marble deposits occur in Paleozoic roof pendants or inclusions in the Mesozoic intrusive rocks in the area (Troxel and Morton, 1962, p. 52).

Jan 1, 1982

By Roger D. Sharpe

The United States Gypsum Company operation at Plaster City, in Imperial County, California, consists of the largest gypsum quarry in the United States, a company-owned, narrow-gauge railroad and wallboard and plaster manufacturing facilities. A variety of gypsum products, including many types of wallboard, construction plasters, portland cement setting agent, and agricultural gypsum are manufactured. Gypsum is quarried from the Miocene age Fish Creek Gypsum. Evaporite minerals were deposited in a clastic-rich sabkha environment along the margin of a small embayment in the Salton Trough. The Salton Trough is a major regional structure that formed by rifting and transform faulting along the Elsinore, San Jacinto, and San Andreas fault zones. Sedimentary basins were formed between tilted fault blocks. The basins were filled by prograding alluvial fans, basin margin sabkha and marine sediments, and deltaic deposits from the Colorado River. Gypsum is exposed in the quarry on rounded hills with 250-300 feet of relief. The evaporites are up to 200 feet thick and average 125 feet in thickness. Anhydrite commonly occurs in the lower part of the evaporites under the crests of hills and beneath thick alluvial cover.

Jan 1, 1995

By J. R. Stone, J. T. Roy

ASARC09s continuous tapper for lead blast furnace is described. Its use throughout the company's plants has resulted in higher production rates, lower labor costs, and better working conditions. It has also permitted wide latitude in blast pressures, as well as in charge and slag compositions. The practice of tapping a lead blast furnace has remained essentially unchanged for many years. In principle, it is a batch operation discharging the products from the continuous smelting of lead-bearing materials. As such, it imposes certain restrictions on the proper functioning of the smelting operation. First, it calls for a highly developed sense of timing, and a considerable amount of physical effort on the part of the operator. Dirty and hot working conditions, as well as the hazards of flying metal and slag, usually prevail. These conditions have resulted in higher labor costs, both in rate and in amount. Labor turnover has also been high. Secondly, rigid control of mechanical and metallurgical factors must be maintained. Frequent oxygen lancing of the tap hole is needed to permit tapping, thereby increasing operating costs. Rapid increases in smelting rate, plugged tap holes, or forgetfulness on the part of the operator may permit the molten material to rise above the tuyeies and freeze the furnace. Also, the operator will often blow out the tap hole after draining, filling the area with fume. Composition of charge also vitally affects the tapping. The type of lead-bearing material being smelted will naturally affect the smelting rate, and thus the frequency of tapping. The amounts and types of fluxing materials, which determine the ultimate fluidity of the slag, must be regidly controlled. Finally, the batch tapping of a continuous smelting operation of this type appears to be wrong in principle. The molten material drains into the crucible at the bottom of the furnace where it starts cooling immediately and continues to cool until tapped out. While keeping the lead molten is no particular problem, maintaining a fluid slag at all times is often difficult, and sometimes impossible. These factors all point to the desirability of a method for the continuous tapping of a lead blast furnace. The expected advantages would be more desirable working conditions, lower labor costs, increased production, and a much wider latitude in both blast pressure and charge composition. CONTINUOUS TAPPING Historical. A number of devices, e.g., mechanical tappers, siphons, and lead wells, have been tried in the past in attempting to effect continuous tapping. None proved to be entirely satisfactory for tapping lead and slag simultaneously. It was not until 1955, however, that ASARCO designed and put into operation a successful tapping unit at its East Helena, Mont. lead smelter. This unit is described in detail in U.S. Patent NO. 2,890,951. Continuous Tapping Unit—See Figs. 1 and 2. Fig. 1 is a schematic drawing of the unit in place, showing front and side views. The component parts are identified in the caption. Fig. 2 is an actual photograph, front view, of the tapping unit attached to the base of the blast furnace. Operation. The operation of the tapping unit is quite simple. Essentially it consists of a narrow tapping bay surrounding the furnace tap hole, with a deep notch in the front wall. When the blast furnace is started this notch is open down to the level of the tap hole. Starting the furnace may be accomplished in several ways but the most satisfactory method is to plug the tap hole with clay, permitting metal and slag to build up inside the furnace. Before the liquid reaches the tuyeres, the plug is removed and the furnace is drained to the settler. The blast is then stopped momentarily while the notch in the front wall of the tapping bay is dammed with chrome brick and plastic chrome ore. The blast is again started, and the height of the dam is adjusted so that the liquid in the bay will counterbalance the internal pressure of the furnace. When the desired level is reached the slag and metal will overflow to the settler. It should be noted that the molten material ,is not siphoned from the furnace and that the metal 'acts as a liquid valve controlling the flow of slag through the tap hole. During normal operations the tapping bay is filled primarily with lead, covered with a thin layer of slag. Thus, the heavier lead plays the major role in compensating for variations in furnace pressures. Due to the high specific gravity of lead, changes in the liquid level in the tapping bay will never exceed a few inches. For this reason it is seldom necessary to change the height of the dam due to minor variations in operating conditions. Some turbulence of the liquid in the bay is essential at all times. This indicates that the level of the

Jan 1, 1963

By S. D. Van Nort

The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc., an 81% owned subsidiary of Freeport-McMoRan Inc., lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in early 1988. Production at the open pit Grasberg deposit commenced in December 1989. The Grasberg copper-gold orebody is contained with a young igneous complex of dioritic composition which intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork.

Jan 1, 1991

By Raymond B. Ladoo

"The name bentonite has been applied to a group or series of clay-like materials characterized by an alkaline oxide and alkaline earth content of 5 to 10 per cent, fine grain Giza, high absorptive powers, and usually very strong colloidal properties.Bentonite probably represents no mineral of fixed composition, and its physical properties vary considerably. The type material from Wyoming is light yellow or greenish yellow in color, but from other localities it may be cream colored, white, gray, pink, dark brown or even black. It is exceedingly fine grained, very plastic and highly absorbent. The appearance may be dull or powdeay, but a freshly cut surface usually has a waxy luster. Some varieties have the appearance of wax and may be cut into very thin, translucent shavings. The fracture of the type material is roughly conchoidal, that of other varieties is platey and shale-like, while still others have no typical fracture. Bentonite is highly absorbent; .hen wetted it will absorb more than three times its weight or seven times its volume of water. Some varieties when wetted with water expand to more than six times (some experimenters report eight times) their original volume. The wetted material is exceedingly smooth and soft and feels like soft soap. Unlike most clays, bentonite is easily fusible at a comparatively low temperature.Under a high-power microscope bentonite seems to consist of extremely small, more or less rounded, grains of uniform size, but the texture of most varieties is so fine that individual grains can not be distinguished.Some varieties when finely ground and thoroughly agitated with water will stay in suspension indefinitely, forming a translucent gelatinous mass. The addition of small amounts of acids or sodium chloride seems to have little or no tendency to raid coagulation or settling. Other varieties of similar analysis and appearance go into suspension more easily, but settle out again in a comparatively short time. It has been suggested that the material which stays in suspension indefinitely is a true colloid of the emulsion or lyophilic type."

Oct 1, 1921

By B. C. Burgess

IN the first edition of this volume,44 feldspar was introduced as "the I commonest mineral of the crystalline rocks," usually in small grains associated with other minerals and commercially produced only from pegrnatites. Now other crystalline rocks, such as alaskites and granites, have become present or potential sources of feldspar. In addition, feldspar has encountered very vigorous competition from such substitutes as nepheline syenite and aplite. COMPOSITION AND PROPERTIES The feldspars form a group of which the principal species are orthoclase, microcline, albite, and anorthite. These are aluminum silicates of potassium, sodium and calcium. There are also a barium feldspar, celsian, and barium orthoclase feldspar, hyalophane, rarely found and of no commercial importance. None of the minerals in the feldspar group are found pure or nearly pure. The potash feldspars, orthoclase and microcline, nearly always contain some albite (soda microcline, an- orthoclase); the soda feldspars usually contain some anorthite (lime feldspar). There is a series of soda-lime feldspars known as plagioclase in which the albite and anorthite molecules replace each other in varying proportions from albite through oligoclase, andesine, labradorite, and bytownite to anorthite. Theoretical chemical composition of the principal feldspars is given in Table 1. The Whiteware Division of the American Ceramic Society sub- mitted a list of definitions of ceramic terms, in April 1947, for use in technical literature. For feldspar it gives: "A group of igneous minerals consisting chiefly of the aluminum silicates of potash, soda and lime, in which one base generally predominates." Commercial feldspars are intergrowths of at least two species of feldspar, which occur associated with one or more accessory minerals such as quartz, muscovite, biotite, garnet and tourmaline as well as with small but varying proportions of the decomposition product, kaolinite. An intergrowth of quartz and feldspar frequently contains

Jan 1, 1949

One of the major changes in the resource industry in the nineties has been the re- internationalisation of the industry. The history of the resource business has been one of companies from the developed world utilising the cash flows from their operations to explore and develop mines in less developed regions of the world. This resource development has progressively generated wealth and economic development, which in tum, has led to a new generation of exploration and mining projects.   InSouth America, Chile had led the way in a mining resurgence, now closely followed by Argentina, Brazil, Venezuela and Peru. Although Chile has long had a significant copper mining industry, the pre-nationalisation phase was driven by American capital; the current phase has been spearheaded by RTZ - BHP at Escondida with Canadian junior companies, in particular, providing major speculative impetus. The Australian junior companies have not been significant in South America.   Although Canadian and USA exploration appears to be in decline, the mining industry, particularly in gold, is buoyant in North America. Interestingly, a number of listed and unlisted Australian companies are active, particularly in United States exploration.   Australian-based companies have dominated the South-East Asian exploration scene, especially in the Vietnam region. To date, the combination of political and legislative uncertainties have failed to lead to significant resource developments in this region. The area remains one of great potential, as exemplified by the exciting developments in Indonesia.   The Philippines has a history of mining, and this has been dominated by both local and North American operators. Both large and small Australian resource companies have a presence in the Philippines, and the development of the copper-gold potential could be impressive over the next decade.   The tales of the undeveloped mineral potential of China are probably rivalled only by the supposed strings of virgin Russian orebodies! Many Australian companies appear to have looked but few have chosen to proceed with Chinese developments. There seems little likelihood that China will, in the foreseeable future, rival South America as a target for Australian and North American resource capital.   Papua New Guinea has had an active, albeit chequered history in mining, with Australia long being the predominant source of exploration and development funds. The developing nation status of PNG has generated extreme uncertainty, with the current exploration scene all but dead. Most recently, the international flotation of Lihir Gold has tested the international and Australian investment community's commitment to PNG resource development.   The Australian exploration scene continues buoyant, although dominated by gold. The base metals scene is generating, on average, one significant base metal mine developed every couple of years. This is probably the fastest rate of significant base metal development in Australia's history.   The gold scene has been one of incredible dynamics, and there is no evidence that this momentum is waning. The development of new exploration techniques, together with a number of the companies reaching a critical size, has added to the momentum in the industry.

Jan 1, 1995

By S. Mansfield, A. Sharma

At a large open cut copper mine, in pit crushing and conveying is used to shorten haul routes and minimise stockpiling of ore. This strategy decreases capital expenditure by reducing the number of haul trucks and excavators required and reduces the need to rehandle ore from stockpiles with a secondary load and haul fleet, with an overall goal of lowering operating costs and carbon emissions. As the mine has developed and expanded, it was necessary to extend the conveying network and install a fourth, semi-mobile crusher to increase the output of the operation, while maintaining the operational efficiencies. This required the blasting of a new tipping bench and pocket for the installation of one of the largest and most powerful semi-mobile, crushing plants. Fed by 360 tonne (396 ton) ultra-heavy class haul trucks, the KB 63-130 Pro gyratory crusher is the highest capacity available in the market. This paper describes the holistic process that was applied to model, design and execute the blasts required to create the pocket for the semi-mobile crusher, the surrounding tipping bench, plus the conveyor corridor and access ramp used by the ultra-heavy class trucks.

Jan 1, 2024

By J. R. Koehler

The U.S. Bureau of Mines (USBM) ground control research program includes several projects focused on developing design criteria for yielding-pillar-based longwall gate road systems. As part of this program, mining practices at the Sunnyside Mines, Sunnyside Reclamation and Salvage Co., Sunnyside, UT, are being documented to preserve the long history of yield pillar system evolution on the property. Published information describing the specific in-mine performance of the numerous gate road configurations utilized at the Sunnyside Mines is very limited. To overcome this deficit, USBM personnel interviewed 30 longtime mine employees representing nearly 700 years of mining experience at the Sunnyside operations. Mining conditions in 12 specific areas in the Nos. 1, 2, and 3 Mines were discussed in the interviews. Also, broad topics such as general mining practices, safety, and geology were often addressed during the discussions. Comprising the body of this report is an extensive record of the events and conditions experienced while mining the identified areas. In addition, eight significant conclusions were developed that accurately summarize the general opinions of the interviewed personnel regarding mining conditions and practices at Sunnyside.

Jan 1, 1994

By David G. Borg, John Bussey

The new AIRDEK (tm) technique for pre-splitting in surface coal mines produces highwall conditions that have greater safety with lower costs for explosives, labor, and drilling. Successful applications have been made in highwalls ranging from 20 to 100 feet or more and in blasthole diameters from 3-1/2 inches to 12 inches.

Jan 1, 1988