Search Documents

By T Davis

The 500 orebody in the upper levels of Mt Isa Mines in north-west Queensland was mined by sublevel caving and block caving from 1962 to 1969. The hot and reactive rock mass of this orebody provided significant mining challenges including ground temperatures above those resulting from the geothermal gradient. Recently Xstrata Copper has been studying the potential to mine this orebody by modern caving techniques. Part of the study process has included re-accessing the ore zones for diamond drilling and trial development. A cross-cut trial drive, the first primary development into the orebody in more than 30 years, encountered a temperature increase in development holes from low sixties to almost 80¦C in less than 10 m advance. The issues associated with managing this risk include sourcing suitable quantities of reactive ground explosives for a single small heading and the temperature limitations of the explosives and detonators. Risk management outcomes included controls to mitigate the safety and reliability risks relating to misfires. The control that dealt directly with the challenge of continuing development in elevated temperature ground was to cool the holes before and during charging. The most effective and practical cooling medium proved to be water. Rapid rock temperature recharge time meant cooling had to continue as close to firing as possible. Reticulation systems were constructed to allow cooling to take place up until withdrawal for firing. No misfires occurred with the cooling system and additional controls in place. This proved that developing safely and effectively in the elevated ground temperatures of the 500 orebody is practicable.

Jan 1, 2008

By J. B. Kwon

For improvement in the productivity of tall building projects, table formwork is one of the main methods that have been adopted for slab formwork. Because the table formwork method is an equipment-oriented construction method, the type of lifting equipment and method of operation considerably affects the productivity and cost of the table formwork. It is also important to make an equipment input plan for completing the table formwork within the time given, according to the structural construction cycle. For performing the table formwork, a tower crane or an independent lifting system, and shifting trolleys, are required. However, if an inefficient equipment input plan is made, exorbitant cost may be incurred. Therefore, the purpose of this study is to analyze the productivity of a table formwork, considering the type and number of lifting equipment and the number of trolleys inputted, and to suggest quantitative data for making a cost-efficient equipment input plan within the construction duration given. It is expected that the results of this research will be utilized as a basis for cost-efficient equipment input planning.

Aug 1, 2013

By Steve Dillingham

In recent years, there has been a trend toward increasingly demanding blasting standards being enacted by local and regional regulatory authorities. The objective of this paper is to alert blasters of the difficulties that are created for blasting projects as a result of these restrictions, as well as the steps that can be taken to minimize future conflicts.

Jan 1, 1995

By G. A. Vissac

MoIstuRe in coal must be considered as an impurity, just the same as ash, from the standpoint of utilization of the coal. Being incombustible, it reduces directly the heating value of the coal, and in addition absorbs heat for its evaporation. Its presence means useless expenditures in handling and transportation. In coke plants, extra moisture reduces capacity and may cause damage to brick work and equipment. Accordingly, the removal of extra moisture can be considered just as important as the removal of other impurities, such as ashes, in the modern coal preparation plant. Moisture, which can be removed by heating the coal up to a temperature of 100°C, may be retained in various forms: 1. As a film, on the surface of each coal particle, and in the interstices between particles, retained by capillary forces. 2. Or "occluded" inside the coal particles. This occluded moisture may be either free moisture (as in a sponge), or hygroscopic moisture which varies with atmospheric conditions, (also called "regain"). These latter forms of moisture are particularly common in "young" coals (subbituminous and lignites); bloom coals (seam outcrops); fusain; and carbonized products. In our study of coal drying, we shall consider only the removal of free moisture, exclusive from hygroscopic moisture. Dewatering If we reserve the name of drying to the removal of water by evaporation, we must consider the initial phase of the mechanical removal of free moisture as a distinct operation covered by the term dewatering. In all cases the free water carried over the surface of the coal particles or in their interstices, or in their pores, is retained by capillary forces. Dewater-ing is accomplished by breaking or counteracting these capillary forces; removal of as much water as possible by dewatering methods is usually advisable, as the cost of these operations is generally much less than by evaporation. The most common methods of me-chanical dewatering are: 1. "Pressure piling," which reduces the interstitial spaces, accomplished in dewatering bins or over dewatering screens. 2. Or dynamic methods, such as used in centrifuges or over vibrating screens. We shall only mention the " preferential wetting" method, in which surface water can be displaced by hydrocarbons, as offering possibilities, but which, to our knowledge, has not reached yet a practical development. But we must point out that the capillary forces retaining water on the coal surfaces, decrease considerably with increased temperatures. This is the principle used in all modern dishwashing machines; by using very hot water, dishes are extracted almost dry. In line with this development, we favor the type of dryers including a dewatering section; as the coal enters the dryer and is gradually brought up to higher temperatures, its dewatering ability is increased and advantage can be taken of this conditioning, resulting in increased drying efficiencies and reductions in drying costs. Heat Drying In the final phase, the remaining moisture must be evaporated. Coal and water must be brought up to the chosen temperature of evaporation, and heat must be supplied to fill the requirements of the latent heat of evaporation of the water to be removed. Accordingly, drying becomes largely a problem of heat transfer, and drying methods can be classified accordingly, namely: 1. Radiant transfer. 2. Transfer by surface contact and conduction. 3. Transfer by hot gas contact. The first method is not applicable to coal drying; the second method is used in the old type rotary dryer. The third method, the most commonly used in modern coal dryers, will be the only one considered here; and, of course, we shall deal with continuous types of dryers only. The mechanism of complete drying is really very complex-—several phases are involved: 1. The constant rate period. 2. The uniform falling rate period. 3. The varying falling rate period. As most of our practical coal drying problems deal with wet coals (over 6 pct of moisture), and do not require complete drying (under 1.5 pct), we shall deal with the first condition only, namely the constant rate drying. Dryer Calculations Instead of presenting the algebraic formulas, we believe a concrete example will provide a clearer illustration. Assume a feed of wet coal at the rate

Jan 1, 1950

By John Birkinbine

Much has been contributed to the Transactions of the Institute concerning the construction and operation of American blast-furnares ; but the following compilation is offered as possibly furnishing additional information upon the general features, dimensions, locations, capacities, etc., of the blast-furnaces of the United States; while, incidentally, the ores upon which they rely are noted in a general way. The paper is presented chiefly as a compilation, and the figures given are selections from most reliable sources, or averages calculated from official statistics, placed for convenient reference, with a view of assisting those who consult the Transactions in determining the present relative merits and importance of various sections of the country. The scope of the paper has been restricted to as few topics as possible, and all the details of special plants, or notable outputs have been ignored. While every effort has been made to give correct figures and data, the changes which are constantly taking place in the iron-producing industry, will, undoubtedly, by the time the paper is in print, develop some errors. It is difficult to determine which of the blast-furnace plants of the country should or should not be considered as upon the active list. A number which have not been in operation for years are still reported as active, some of which will scarcely be put in blast again, and others are handicapped so that they can only operate in times of abnormal profits. It is therefore scarcely probable that there are over 600 blast-furnaces in the United States which can properly be considered as active; but so many considerations affect the various plants, that, it being impossible to determine the exact number, I have relied upon the annual reports presented to the American Iron and Steel Association. Concerning the number of plants which could be stricken from the list, the Secretary of this Association says: "In January last (1885) we enumerated 669 furnaces, which included many stacks which had not been in blast for a very long time, and others which could not be operated except during short periods of exceedingly high prices for pig iron. We have gone over this list very carefully and have eliminated 10 anthracite, 19 bituminous, vol. xiv.—36

Jan 1, 1886

By Miles M. J, Sandy D. A

It has long been known that drilling and blasting operations have a direct influence over productivity and costs of subsequent operations. If mine management is to effectively optimise blasting operations, good information is required on the operating costs of each of the affected operations, together with knowledge of how they are influenced by blasting. In practice it is not possible to do enough repeats of a full scale production blasting experiment to make a statistically significant analysis of the results. By monitoring each blast and subsequent operations in as much detail as possible, enough data will be available to effectively measure the effect of blasting on costs. This gives management an insight into the blast performance and is the first step towards optimisation. An Integrated Blast-related Cost Reporting System has been developed at the Rossing Mine Open Pit, which calculates the total mining cost for each blast. In assessing the total mining cost for each blast, use was made of an.integrated planning and management information system to collect relevant production variables, current operating costs and survey data. An automatic image analysis system was employed to measure the fragmentation of the blasted material in the back of haul trucks. A shovel monitoring system is also under development for use in assessing the muckpile diggability and, in conjunction with an appraisal of shovel component reliability, to estimate the maintenance cost under various digging conditions.

Jan 1, 1990

By L. Cheng

This Bureau of Mines report summarizes an investigation of the amount of respirable dust adhering to the surfaces of seven run-of-face broken bituminous coals. The number of respirable-size (0.9 to 10 micrometers) particles adhering to the run-of-face coal ranged from 1011 to 1012 particles per pound of coal and was approximately inversely proportional to the mean lump size of the coal sample, otherwise it did not vary significantly with the coal seam, mining method, or winning machine. Based on these results, about 16 lb of ordinary run-of-face broken coal would have enough respirable-size adhering dust to contaminate 1,000,000 ft3 of air up to the 2 mg/m3 level, if this adhering dust should become airborne. Although brief studies here suggest that a negligible amount of new respirable dust is formed due to fracture of the broken coal during dropping, dislodging of old adhering particles during secondary handling operations is a potentially dangerous source of airborne respirable dust.

Jan 1, 1973

By Anderson Dana

THIS PAPER describing methods and costs of mining and preparing gravel and sand for market at the Port Jefferson plant of the Seaboard Sand and Gravel Corporation, is one of a series of articles on gravel and sand mining, prepared for and published by the U. S. Bureau of Mines, which is designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs, It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical [ ]

Jan 1, 1932

By Charles Parmelee

When Professor Silliman made his first examination of the newly-discovered Pennsylvania rock oil in 1859, he noted that different rates of heating produced different results in fractionation—longer heating produced larger percentages of light fractions. In 1862, it was found that when petroleum vapors are condensed in the still crown and dropped back into the hot liquid, the result of the distilling operation is materially modified. These early dates mark the beginning of what is called cracking petroleum and is explained as separating the component parts of the hydrocarbon molecules into more and smaller groups of the same elements. The phenomena were utilized for the next 30 years to increase the yield of burning oil. The procedure was that regularly practiced today in dry or destructive distillation. Considerable scientific study was given to the subject from 1862 to 1905, and a number of patents were obtained, but the work done was not continuous or intensive until about 1905, when the increasing demand for gasoline attracted attention of petroleum refiners to the possibilities of cracking. The first equipment built and operated essentially for cracking petroleum on a large scale was placed in successful operation in 1912. The commercial practice is, therefore, less than 15 years old. Comprehensive intense study of the controlling factors during this period has resulted in rapid increase in our knowledge, and material improvement has been made in the practice of the art. It is the purpose of this paper to outline briefly the state of our knowledge and to suggest some of the questions which are attracting attention of researchers at the present time. The major purposes for which petroleum hydrocarbons, including natural gas, are or have been cracked are: 1. To obtain products used to increase the heat value and illuminant content of artificial gas. 2. During the World War, to increase the supply of toluol. 3. To increase the amount of products capable of conversion into industrial chemicals. 4. To produce pure carbon.

Jan 1, 1927

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupation-al Research Agenda, problems created by occupational hearing loss include(1) reduced quality of life due to social isolation and unrelenting tinnitus,(2) impaired communication with family members, the public, and coworkers, (3) diminished ability to monitor the work environment (i.e., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers? compensation and hearing aids.

Jan 1, 2001

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported1 that acid-soluble titanium decreased the hardenability, with multiplying factors less than unity according to Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying fdctors up to nearly I.; for about 0.1 per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 1.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correc- tion for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non-titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. Comparison of Plain-carbon, Vanadium and Titanium Steels The five steels used for these experiments were cominercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat1 containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain carbon

Jan 1, 1947

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported1 that acid-soluble titanium decreased the hardenability, with multiplying factors less than unity according to Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying fdctors up to nearly I.; for about 0.1 per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 1.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correc- tion for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non-titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. Comparison of Plain-carbon, Vanadium and Titanium Steels The five steels used for these experiments were cominercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat1 containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain carbon

Jan 1, 1947

By Yan Germain, Université Laval, Bernard Dallaire, Jocelyn Bouchard, Peter Radziszewski, Gilles LeBlanc, Michelle Levesque, Nicolas Tremblay

"The comminution process is estimated to be only 1% efficient, resulting in waste energy dissipated as heat, noise, and vibration. Energy recovery from grinding circuits has not been implemented mainly because recovering heat from the surface of the grinding mill or from mill slurry can impede operation, increase maintenance requirements, and prolong plant shutdown time (and production). However, currently very little information is available in the public domain regarding the amount of waste energy and that potentially recoverable in the grinding circuit of a mineral processing plant. Availability of such information could drive innovation and improve decision-making regarding opportunities for waste energy recovery. The Canadian Mining Innovation Council (CMIC) has initiated a study with CanmetMINING and mining industry partners to develop a model to map the energy flows in grinding circuits and to quantify the potential for energy recovery. The paper outlines the underlying fundamentals and data requirements for use in the model and then focuses on quantifying the energy recovery potential of the semi-autogenous grinding and ball mill circuits at the Agnico Eagle Goldex Division. Results show that most of the electrical energy (over 75%) is used to heat the slurry, leaving only a relatively small amount of it to achieve mechanical work (~9%). INTRODUCTIONCanmetMINING commissioned a study in 2013 to better understand the barriers for adoption of new technologies in the mining industry (MNP, 2013). The conclusions highlighted the importance of enhancing industry/regulator engagement and communication to raise awareness and improve the industry’s comfort level with new technologies.In November 2014, the Green Mining Innovation Advisory Committee (GMIAC) held a workshop to explore the possibility of accelerating the uptake of green mining technologies by bringing together key stakeholders among the mining value chain to address industry priorities. Participants included representatives from mining companies and associations, academia, provincial governments and federal departments and organizations. Two key priority areas emerged at the workshop: i) energy saving, and ii) water management."

Jan 1, 2016

By David K. Melgaard

Electroslag Remelting (ESR) is a complex process used to produce high quality specialty alloy materials. The quality can be directly correlated to variances in melt rate and immersion depth. Conventional ESR furnaces control these quantities using two independent control loops using proportional changes in current for melt rate and driving the electrode up and down to match a voltage set point for immersion depth. However it is well known that the control loops are highly coupled, i.e. changing the current to account for melt rate deviations changes the voltage depth relationship and vice verse. In addition the noise in measurements of the ESR process can be considerable, forcing conventional controllers to use highly damped responses. A new model-based controller has been developed to embody the coupling and improve responsiveness by using estimates from a reduced-order linear ESR model and the typical process measurements to control melt rate and immersion depth simultaneously. Kalman filtering is used to optimally combine the model estimates of eight process states and the measurements of voltage, current, position and mass to estimate the instantaneous melt rate and immersion depth. Several ESR melts under steady state and transient conditions were conducted to evaluate the performance of the new controller. This paper will discuss the design of the new ESR model and controller and will present experimental results demonstrating its much improved control and responsiveness. While this controller was developed for the ESR process, the effectiveness of model-based control in managing such a complex process with relatively simple equations suggests the approach could be employed for many other processes as well.

Jan 1, 2006

By S. J. Neethling

"Liberation is a key driver in all mineral separation processes as it limits the maximum possible grade for a given recovery. In flotation, this is further complicated by the fact that it is surface exposure of the floatable minerals that determines the ultimate performance. Liberation, grade and surface exposure are commonly quantified using Scanning Electron Microscopy coupled to Energy Dispersive X-ray spectroscopy (SEM/EDX) analysis of polished sections. The intrinsically 2D nature of this technique can result in significant sampling errors and stereological effects that can affect the quantification of the ore’s textural characteristics. X-ray micro-Tomography (XMT) is an imaging method that can non-invasively and non-destructively delineate ore fragments in 3D, thus providing an alternative method that eliminates the need for stereological corrections and readily provides surface exposure. A methodology and automated algorithm were designed for extracting this information from images of closely packed particles, thus allowing samples containing a large number of particles to be assessed.The main drawback of XMT is that, unlike SEM/EDX, it cannot directly measure the mineralogy of the sample, instead producing a 3D X-ray attenuation map. We therefore also present an algorithm for calibrating the thresholding of the XMT images based on SEM/EDX images of sections through the same sample, thus allowing the liberation analysis to be carried out on a 3D mineral map in which the uncertainty in the mineral assignment is small and statistically quantified.The methodology was tested on low grade porphyry copper ore as this is both an industrially relevant and traditionally difficult system to quantify using XMT due to the similarity in the X-ray attenuation of the sulphide species, especially the pyrite and chalcopyrite. As each 3D volume imaged contain 100-1000s of grains, large data sets can be readily produced. By dividing these particles into classes based on both their surface exposure and grade, the extent to which there is preferential breakage of the particles can be assessed—an important consideration if sufficient surface liberation for good flotation performance is to be achieved at coarser particle sizes. It is also shown that erroneous conclusions can be drawn when basing the analysis on 2D sections through the particles."

Jan 1, 2018

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By J. L. Taylor, P. Duwez

PARTIAL phase diagrams of titanium with iron, cobalt, and nickel have been established by previous investigators.1-3 These diagrams seem to be reliable, at least for concentrations of titanium ranging from 0 to about 50 at. pct. More recently, Long and his collaborators have presented a tentative titanium-nickel diagram covering the titanium-rich side.' These various studies indicate that in each system three intermediate phases exist and correspond to the compositions Tia, TiX, and TiX2 (or TiX3). The purpose of this paper is to review the available information on the crystal structure of these phases and to give the results of additional X-ray diffraction studies. Previous Work A summary of the work of Wallbaum and his collaborators"-' is presented in table I. The first intermediate phase on the titanium-rich side of the three systems, with iron, cobalt, and nickel, is of the Ti2X type and has a face-centered cubic structure. Although it is stated that the unit cell contains 96 atoms: no lattice parameters are given. The second phase is centered around the compositions TiX for the three systems. The crystal structure of this phase is mentioned in a short note" as being body-centered cubic (CsCl type), but no parameters are given. The analogy between the three systems, which is perfect as far as the two phases of the type Ti2X and TiX are concerned, disappears at the titanium-poor end of the diagrams. In the system titanium- iron, TiFe2 has an hexagonal (MgZn2 type) struc-ture with the parameters given in table I. The existence of TiFe3 has also been reported8 (table I) but was questioned by other investigators2 and is also refuted by the present study. In the system titanium-cobalt, a phase corre-sponding to the composition TiCo2 has been investi-gated by Wallbaum and Witte6 who claim that the structure is cubic (MgCu2 type) for alloys slightly deficient in cobalt and hexagonal (MgNi2 type) for alloys slightly deficient in titanium. The parameters of the two phases are given in table I. In the system titanium-nickel, the nickel-rich phase corresponds to the composition TiNi3 and has been described as hexagonal7 with the parameters given in table I. The present investigation was initiated for the purpose of filling in the gaps in the knowledge con-cerning the structure of the various phases sum-marized in table I. Since the titanium used by Wallbaum and his collaborators was only 95 pct pure,' it was found desirable to redetermine the lattice parameters of the alloys prepared with a

Jan 1, 1951

By R. Tipman

"In 25 years, processing of tar sand progressed from two small pilot plants to two major commercial operations owned by Syncrude and Suncor. These plants mine tar sand and extract the bitumen which is then converted into a synthetic crude oil. Considerable research on extraction of bitumen from tar sand has been undertaken by these two companies as well as other major oil producing companies, private individuals, universities and the federal and provincial governments. These studies have produced a number of alternate processing schemes which have yet to be commercialized. The producing companies are focusing their efforts on achieving increased processing efficiency, which includes improved bitumen recovery, reduced unit cost, energy conservation, and equipment reliability. In this review, the Syncrude process and examples of new process developments will be briefly described. IntroductionTwenty-five years ago, tar sand processing was limited to two pilot plants owned by Cities Service Athabasca Ltd., and Great Canadian Oil Sands. Earnest Manning was Premier of Alberta and was inviting proposals for the construction of a commercial tar sands plant. The invitations called for a much larger operation than those which had been undertaken in the past. All of the previous attempts at commercial operations up to 1960's had failed, largely because of a poor technical understanding of the process requirements, lack of suitable equipment, and lack of adequate capital. The previous record was not good. The pending new large scale plant was based on improved but not proven technology and equipment, which were developed from the pilot plant studies. In addition, the surplus of conventional oil in Alberta and low world oil prices were factors reducing the need for such a plant."

Jan 1, 1987

By Robert Small, Amshu Chappa, Ihab Allam

The Biosolids Digester Facilities Project (BDFP) is located in southeast San Francisco. The jobsite is bounded by active Caltrain and Union Pacific Railroad tracks on the west side and the existing Southeast Treatment Plant (SEP) on the north, south and east sides. The existing SEP was constructed in the 1950s and portions of the facility have reached their operational life. The $2 billion BDFP will replace and relocate the outdated existing solids treatment facilities with more reliable, efficient and modern technologies and facilities. In addition, the nearby Bayview and Hunters Point neighborhoods will benefit from the improved odor control. MWH/Webcor, a joint venture, as the construction manager general con- tractor (CMGC) for the project. As part of an alternate delivery method set forth in the prime contract, the CMGC was permitted to propose the use of a core trade subcontractor partner for the SFPUC's approval to provide precon- struction services. The CMGC identified three major scopes (electrical, mechanical and foundation) where a core trade partner would be able to assist

Jan 1, 2023

By Wieland D. R., Hurst R. E., A. R. Hendrickson

Analysis of acidizing techniques, in correlation with reservoir data and a backlog of past treatments, has resulted in the development of a valuable engineering guide for planning acidizing treatments. Such treatments fall into three categories: (I) acid injection into the pores of the matrix; (2) acid injection into natural formation fractures at less than parting pressure; and (3) combination acidizing-fracturing treatments in which acid solutions (without propping agents) are injected at treating pressures sufficient to open and extend fractures through which the acid flows. Because the spending tirnze of acid during a specific well treatment does not change appreciably, maximunl penetration is attained when the first increment of injected acid is completely spent. Additional acid injection cannot be expected to further extend the benefits of the treatment. Depth of penetration will depend upon the reaction rate of the acid under treatment conditions, the injection rate of the acid into the matrix or fractures and the area-volume relationship existing in the flow channels. Based on Darcy's flow formula, extremely low injection rates must be used in order to keep bottom-hole injection pressures below formation fracturing pressure. As a result, only limited penetration of unspent acid will occur. Treatment records indicate that, in most acidizing treatments, formation parting pressures are exceeded, greatly extending acid penetration. Under these conditions, stimulation benefits are limited to the fracture area produced during the spending time of the first increment of acid injected into the formation. This area may be calculated from laboratory and well data to estimate depth of penetration. This, in turn, may be correlated with productivity data to assist The art of gas and oil well acidizing has been characterized by many changes in treating materials and techniques since its inception. These developments have been designed to provide greater production increases. prolong production declines and shorten payout time. Such improvements have been based primarily on data derived from laboratory research and field experience. As more of the variables influencing these treatments have been recognized and evaluated, acidizing has become less of an art and more of a science. Recent studies of fracturing treatments,' in light of individual well conditions and the results of thousands of fracturing treatments, made possible the formulation of an engineering guide that is now being used to select optimum treating techniques and to forecast probable results of such treatments. A similar analysis of the factors controlling acidizing treatments has been made and is the basis for this paper, The findings herein can be used as a guide in the selection of acidizing solutions and techniques, tailored to fit specific well conditions and to provide optimum stimulation per dollar cost. Acidizing treatments may be classified into three basic categories—(1) treatments in which the acid is injected uniformly into the pores and flow channels of the matrix, (2) treatments in which the acid enters natural fissures and fractures in the formation at less than fracturing pressures and (3) injection of acid into the formation at a pressure sufficient to open and extend fractures into the rock through which the acid penetrates (without the inclusion of a propping agent). TYPE 1 — MATRIX ACIDIZING This category consists of treatments in which acid solutions are injected into a homogeneous carbonate