Search Documents

By John S. Alexander

The typical block coal of the Brazil (Indiana) District differs in chemical composition but little from the coking coals of Western Pennsylvania. The physical difference, however, is quite marked; the latter has a cuboid structure made up of bituminous particles lying against each other, so that under the action of heat fusion throughout the mass readily takes place, while block coal is formed of alternate layers of rich bituminous matter and a charcoal-like substance, which is not only very slow of combustion, but so retards the transmission of heat that agglutination is prevented, and the coal burns away layer by layer, retaining its form until consumed. This property permits the use of raw block coal in the furnace but theo-

There are a number of mineral processing operations which produce at some point a stream of hot particulates. At today's energy prices it becomes important to recover the energy held in the hot particulates. Sometimes it is convenient to use gas, e.g. in air pre- heating, and this will be appropriate in some circumstances. There are cases where it would be very useful if energy in the hot processed particles could be exchanged to the cold feed solids. This can be achieved within appropriate limitations by countercurrent heat exchangers comprised of parallel channels which contain, alternately, fluidized solids of 'hot' and 'cold' streams respectively. A pilot- plant has been built. Some calculations relating to industrial application will be Presented.

Jan 1, 1981

By D. C. Dahlin, W. K. O’Connor, G. E. Rush, C. A. Summers, S. J. Gerdemann

The Albany Research Center (ARC) conducted studies of mechanical activation by conventional and ultra-fine grinding techniques to enhance olivine reactivity in mineral carbonation reactions. Activated olivine is one of several solid feed materials used at ARC in reactions with carbon dioxide to form carbonate minerals. This paper compares grinding techniques via energy demand data and product characteristics, including particle size distributions, surface areas, full width at half maximum (FWHM) XRD analyses, and particle morphology by SEM analyses. Reactivity was gauged by percent conversion to carbonate in subsequent carbonation tests.

Jan 1, 2004

By H. C. Siebert

According to the "Survey of Energy Resources 1980" (1)*, which was prepared by the Federal Institute for Geosciences and Raw Materials in Hannover (FRG)for the World Energy Conference 1980 in Munich, the world coal deposits are assessed at 775 billion tce proven reserves 448 billion tce of them recoverable and 6 161 billion tce additional resources. If one ignores growth rates, the current world coal output of 2,8 billion tpy gives our recoverable reserves a static life expectancy of 175 years. With an average increase in world output of 3,2 % like between 1973 and 1980 this range would be further shortened to an alarming degree. Furthermore, the criteria used to distinguish between workable and unworkable resources give rise to the suspicion that deposit characteristics are not always taken into account to a sufficient degree. For example, little attention is paid to major ?Bonitaet" - factors such as dip and seam thickness. There have been wide-ranging scientific discussions on the lower limit for workable coal resources, but no such limits have been set at the other end of the scale. Otherwise it is well known that performance and costs are badly affected den in level and moderately inclined seams the seam thickness is more than 4 to 5 m, because special mining methods have to be used beyond this limit. These are associated with significantly higher costs than with the winning of seams of ?normal? thickness.

Jan 1, 1985

By P. Mousset-Jones, G. Danko

Rock thermophysical properties, i.e. heat conductivity and thermal diffusivity, were obtained for reference values at the Waldo Test Mine for mine fire simulation purposes. An in situ measurement method was chosen since it could include the effect of rock fractures. The REKA method (Rapid Evaluation of k and alpha) was used because it can measure conductivity (k) and diffusivity (alpha) simultaneously within an eight-hour measurement period. A total of six measurements were taken in three different holes, and at two different depths from the collar of the hole. Each measurement provided an averaged conductivity and diffusivity for a volume of rock of approximately one cubic meter. The boreholes were driven into the upper and lower limestone, two at right angles to and one parallel to, the stratification of the rock. Significant representative conductivity and diffusivity values were obtained for the whole mine by averaging the six measurement results. The thermal properties for the band of shale in between the two limestones were not measured in situ, but only in the laboratory. Problems were encountered in the evaluation because of unexpected heat conduction on one side of the symmetrically built probe. A modification was made to the previously developed evaluation method together with further testing and correction, before the final results were obtained. As expected, the in situ and lab- oratory measured values of k and alpha compared favorably, since the in situ rock was dry and relatively unstressed.

Jan 1, 1989

By Charles L. Hosler

My function here today is not to illuminate any particular subject but simply to welcome you to Penn State and to the College of Earth and Mineral Sciences. Our college is, of course, dedicated to the same thing to which most of you have dedicated your lives--the exploration of the earth, the extraction of materials from it, and the production of useful things from those materials. We have about 2,000 students engaged in studying in preparation for service in these activities at the present time. Like other colleges of our type, we've undergone a great expansion just at a time when university budgets are contracting. This creates an interesting situation as to how we can best use our resources. This, of course, is the thing a lot of you are going to be talking about here--how we can best use the world's resources. As you well know, the expectations of the people of the world are rising, and, with the numbers of people increasing and with finite resources, there never was a time in history when it was more important that we become "quantitative" in our discovery, estimation, extraction, and utilization of those resources. I think it is admirable and very timely that you are gathered together to discuss your various approaches to this particu¬lar problem of quantifying and making most efficient use of the resources of the world. Yours is sort of a hidden profession, not just because you actually go underground, but because the public in general is not aware of where the materials they use come from. If you are successful in your professions the public will continue to be unaware. Only if you fail will your essential function become patently obvious. I wish you success both in your professional pursuits and in this particular meeting.

Jan 1, 1977

By Robert King

Splicing portable trailing cables used in underground coal mines is usually less expensive in terms of capital outlay and production time lost than replacing them. However, handling trailing cables may result in electrical arcs, shocks , and burns. Also, destructive forces encountered during a mining operation may shorten the effective life of a cable splice. This report gives the results of an analysis of cable splice defects in an effort to establish cable splice performance criteria, determine testing standards for cable splices, establish guidelines for training programs in cable splicing, and indicate areas for improvement.

Jan 1, 1975

By Onwukamike, Onyedika G. O, Ogwuegbu M. O. C., K., Onyenehide C

A detailed mineralogical and elemental characterization of a lead (Pb) ore deposit from Ishiagu, Ebonyi State, Nigeria was carried out with XRD, SEM-EDX, and ICP-OES based mappingtechniques. The results show that the most dominant and valuable metal is lead (Pb = 95.02%, mass fraction). The main mineral is galena. Ilmenite and sphalerite occur as minors, which account for 2.71% and 0.80% respectively. Elements like Al, Ca, Mg, Ti, Na, Mn, Si and Sn occurred in trace amounts and are disseminated in the entire ore body.The surface and interrelations of the crystals were examined with x-ray mapping and the result shows the pattern of dissemination of the minerals within the ore body.

Jan 1, 2015

By H. Rosen

The pump is the heart of most industrial and mining plants, providing the energy to separate valuable minerals from process feed. The actual effect of the pump, both in terms of production costs and overall process efficiency, is often assumed or misunderstood by engineers due to insufficient pump performance data. Pump performance can be understood and corrected, where required, through continuous performance monitoring, leading to dramatic improvements in both pump life cycle costs and system efficiencies. The performance of every pumping application is subject to variation and the main contributing factors are as follows: ?Unavoidable deviations from pump supplier curves ?Pump wear ?Pump curve derating factors for slurry pumping ?System curve variation ?Deviation from basic principles of centrifugal pump operation. These are discussed in detail through case studies and the author?s personal experiences. This paper shows ways to minimize the effect of these variations, thereby reducing performance loss and preventing damage to the pump. The paper discusses the benefits of efficient pump operation, the requirements of pump performance monitoring, and its practical application to pump operation in the slurry and water environments. The cost of remedial actions is explored and compared against the savings in both power and plant reliability, resulting in a reduced life cycle cost of the pump.

Jan 1, 2010

By Barbara A. Filas

The IFC goal is to promote private sector investment in developing countries which will reduce poverty and improve people?s lives. The developing country goal is to promote health, education and employment opportunities that improve their economies and their standard of living. The mining company goal is to Promote successful ?triple bottom line? mining projects that will grow shareholder equity

May 1, 2002

By Daniela Rodríguez

El presente trabajo tiene como objetivo resaltar la importancia de las obligaciones inherentes a la relación del Estado peruano con un inversionista del sector minero -conocidas a nivel internacional como Legítimas Expectativas-, y pone en evidencia que su análisis en los casos concretos de redacción de normas aplicables al sector minero podría disminuir el número de controversias llevadas a arbitraje y a su vez -en virtud de una buena imagen internacional- permitiría potenciar la inversión privada en el país.

Sep 29, 2023

Citigold Corporation operates the Warrior gold mine at Charters Towers, northern Queensland, mining narrow quartz veins (0.1 to 2 m wide) in granodiorite by long hole open stoping on levels 15 m apart. Access is by decline and cross-cuts with on-ore development drives. The mineralisation comprises Palaeozoic mesothermal quartz veins containing gold, pyrite, sphalerite and galena, hosted by the Ordovician age Towers Hill Granite. The gold grain size is variable from 1 to 500 ¦m with 1 m face samples up to 800 ppm Au, and average run-of-mine grades of 10 to 14 ppm. Despite the spectacular gold tenor, little visible gold is present. Gold grades are highly variable presenting challenges in ore reserve estimation. Tonnages are discounted by 70 per cent to allow for the low payabilities (30 to 50 per cent) of the veins. Estimation techniques allow high confidence in overall global grade estimates but poor reliability on a local scale (25 m). Kriging ranges as low as 5 - 8 m means that obtaining a Proved Ore Reserve by diamond drilling is not economically feasible, and broad-scale mine planning decisions are made at the Inferred Mineral Resource stage and mine design work at the Probable Ore Reserve stage. Proved Ore Reserves can only be estimated after underground development has proceeded through the mineralised body with levels at 15 m vertical spacing sampled at 2 - 3 m intervals along the level. However, reconciliations between actual gold produced and earlier resource estimates produce workable results. A further three mines are scheduled to be developed underneath the city of Charters Towers.

Jan 1, 2008

In the present work, the flotation behaviours of zircon, rutile and ilmenite using sodium oleate as collector in absence and presence of depressants were thoroughly investigated. The maximum in the flotation recovery of any of the above minerals falls within similar pH ranges. A range of inorganic and polymer depressants were examined in order to improve the separation of zircon from rutile and ilmenite. Optimum values of conditioning pH and depressant concentration to achieve maximum recovery and best selective floatability of zircon were obtained. Selective flotation of zircon from Ti-bearing minerals was anticipated from single mineral experiments under different pH values, depressant and collector conditions.

Jan 1, 2014

By Michael Lane

With the success of their existing casino operation on the Ohio River in Lawrenceburg, Indiana, the Indiana Gaming Co., LP planned a major expansion of the current facilities. This expansion includes a second 1400+/- car parking garage, a new surface parking lot, elevated walkways, and a new floating casino that will double their present square footage and consolidate all of the gaming activity to one floor. In March of 2006 Richard Goettle, Inc. was awarded the general contract to construct a 260? x 520? boat slip for the new Argosy VII floating casino. An Open Cell® bulkhead system was specified as the means for constructing the new slip. Our contract included the purchase and installation of 300,000 square feet of PS27.5 sheet pile, excavation of 230,000 cubic yards of soil, and a 3300 square foot Mechanically Stabilized Earth wall.

Jan 1, 2008

By Paula Maria Gomes Cunha Leão, Flávio de Castro Dutra, Fabrício Vilela Parreira, Silvio Maranha

In the iron ore beneficiation, tailings are inherent in the concentration processes to which the ores are subjected for the production of commercial products. The large generation of tailings has been motivating the study of technological alternatives for its reuse, with the development of processes that contemplate the concentration of fine ore particles present in the tailings, such as the reintroduction of these particles in the process of manufacture of the iron and steel itself, through the agglomeration techniques such as briquetting. The aim of this article is to study the technical feasibility of the production of iron ore tailings and coking coal briquettes for use in reduction reactors, through a systematic review of the literature on agglomeration, briquetting and self-reduction processes, covering the main variables that influence the production of high quality briquettes, such as binders use, binder behavior of coking coal, coal granulometry, iron ore and coal proportion, compacting pressure and temperature of thermal treatment and the effects of these variables on briquettes final properties.

Oct 1, 2019

By G. Chung, W. Petruk, D. Doyle

"A series of tests was conducted on Carol Lake iron ore, which contains about 38 wt % hematite and 19 wt % magnetite, to establish a flowsheet for high weight yield by spirals. A pilot plant was run in parallel with the IOC concentrator to simultaneously test two flowsheets on the same feed material. The IOC concentrator processes the ore by treating it directly in a spiral circuit, whereas the pilot plant used a laconite flowsheet which had a low intensity magnetic separator (LIMS) at the front of the circuit. The LIMS produced a non-magnetic (hematite-rich) product and a magnetic (magnetite-rich) product prior to treating the ore in two separate spiral circuits. The results from about 150 tests were evaluated by chemical assays and materials balancing techniques, and a selected test was evaluated by the image analysis and materials balancing technique.The image analysis and materials balancing evaluation showed that a higher hematite recovery was obtained by the hematite spiral circuit than by the IOC concentrator spiral circuit, and a slightly lower magnetite recovery by the magnetite spiral circuit than by the IOC concentrator spiral circuit. Furthermore the hematite recovery by hematite spirals was higher than the magnetite recovery by magnetite spirals. The better hematite recovery was achieved because a higher liberation is obtained for hematite than for magnetite, and the hematite in the Carol Lake ore has a narrower grain size range than magnetite. Consequently, better spiral control can be maintained when processing a hematite-rich spiral feed, than when processing a magnetite-rich spiral feed. Since the feed to the IOC concentrator spiral is a mixture of hematite and magnetite, an intermediate hematite recovery is obtained by the IOC concentrator. INTRODUCTIONA study of characteristics that affect recoveries of hematite and magnetite from the Carol Lake ores of the Iron Ore Company of Canada (IOC), was carried out in connection with a project on designing a flowsheet for maximum weight yields. A pilot plant using a taconite flowsheet was run in parallel with the existing IOC concentrator which uses a classical iron ore flowsheet. About 150 tests were run to compare iron recoveries and weight yields by the spirals in the two flowsheets. Better iron recoveries were indicated for the taconite flowsheet, but the results were not consistent and the reasons for the observed differences were not apparent. The material from one test (Test 61), which gave better iron recoveries for the taconite flowsheet, was evaluated by the image analysis and materials balancing technique. A suite of samples was taken from 5 points in the IOC concentrator and from 8 points in a pilot plant (taconite flowsheet). The samples were analyzed to compare the behaviours of the Carol Lake hematite and magnetite in the spirals of the two flowsheets. The results provided a sound basis for further tests in designing a high weight yield flow sheet."

Jan 1, 1993

By Y. P. Chugh

The paper discusses laboratory and field studies to analyze time-dependent deformation behavior of immediate weak floor strata in an Illinois coal mine. In the laboratory, core samples of the immediate floor strata were subjected to incremental creep tests under unconfined compressive stress. Both axial and lateral creep deformations were recorded. Time-dependent behavior was reasonably characterized by a Burger model with one Kelvin-Voigt unit. The elastic and viscous parameter8 of the model were found to be stress-dependent, but in the range of 40% to 80% of the failure stress, the effect of stress was relatively small. Therefore, a linear visco-elastic model was developed to represent the laboratory time-dependent behavior of immediate floor strata. Such a model may be acceptable for the design of partial extraction mining systems having extraction ratios of 40% to 60%. Field observations of roof-floor convergence (floor heave) at the mine also indicated a time-dependent behavior similar to that observed in the laboratory. Field time-dependent behavior was also characterized in terms of a Burger model with one Kelvin-Voigt unit to obtain scaling factors between the field and laboratory parameters. This approach should help in predicting likely floor heave in the mine based on laboratory creep tests. It was concluded that additional studies in the field are required to arrive at more reliable correlations between the two sets of parameters.

Jan 1, 1987

By William Blake

Mining induced rock bursts have been a severe operational hazard associated with the deep silver mines of the Coeur d'Alene mining district for over 30 years. Recent studies during the past fm years have led to a better understanding of the different types of rook bursts and their causative mechanisms. This has resulted in ground control measures that more effectively minimize burst occurrences as well as contain burst damage. Case histories of burst incidences and examples of control measures are presented.

Jan 1, 1987

By W Potma, C Brauhart, S Halley, S Urbisinov, A Scogings

Truly integrated, quantitative, 3D GEOmetallurgical (or mineral system) characterisation, classification and 3D modelling should provide a cradle to grave unifying link across the exploration and mining value chain. All too often, spatially representative (quantitative) characterisation and modelling of a mineral system is delayed until feasibility stage, incurring a significant opportunity cost. The application of robust GEOmet characterisation methods early in the project lifecycle (at exploration stage) improves ground selection, exploration, and Mineral Resource estimation outcomes, long before there is a need for metallurgical test work. The value of this early provision of quantitative 3D mineralogy models is compounded at project feasibility stage, and continues to accrue over the entire project lifecycle, delivering cost savings, improved decision making and early warning of issues and opportunities.CITATION: Potma, W, Halley, S, Scogings, A, Urbisinov, S and Brauhart, C, 2018. Putting the ‘GEO’ back in front of GEOmetallurgy: importance of early implementation of quantitative mineral system characterisation, classification and modelling, in Proceedings Complex Orebodies Conference 2018, pp 55–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By N. Gopalakrishnana, R. Beccard, S. Lourdudoss, R. Holz, M. Deschler

"Rapid growth of conducting and/or insulating InP, GaAs, Gao.47In0.53As, and GaAs0.6Po.4 on one or more of (001), (110), (111)A, (3ll)A and (3ll)B surfaces by Hydride Vapour Phase Epitaxy (HYPE) is demonstrated. The maximum growth rate of the binaries lies between 12 and 300 µm/hr and of the ternaries between 7 and 170 µm/hr. A simple model is developed to describe the influence of crystallographic orientation on temperature dependent growth rates. The growth rates predicted by the model is compared with the experimental values. Room temperature resistivity of insulating InP:Fe can be as high as 5xl09 ohm cm. Temperature dependent differential resistivity is also analysed. This feasibility of growing conducting and insulating layers rapidly on different orientations is very useful for electronic and optoelectronic devices.IntroductionRecently there is a renewed demand for very thick layers of III-V compound semiconductors for high performance electronic and optoelectronic devices [1]-[2]. Long wavelength high speed lasers that can be modulated up to 30 GHz necessitate epitaxial growth of semi-insulating (SI) layers [3]. There is also an increased interest on the growth of epitaxial layers on surfaces other than (001) surface. Epitaxial growth of these materials on such surfaces is of theoretical importance besides being technologically relevant. These demands led us to focus on the growth of conducting and insulating III-V compounds by Hydride Vapour Phase Epitaxy (HYPE). lnP, GaAs, Gao.471no.s3As on lnP and GaAso.6Po.4 on GaAs were grown as conducting materials using Low Pressure HYPE (LP-HYPE) on (001) 2° off substrates. Gao511no.49P on (001) GaAs substrate and lnP on lnP substrates of (001), (110), (l 11)A, (31l)A and (3 ll)B orientations were grown as semi-insulating materials using Atmospheric Pressure HYPE (AP-HYPE). In this report we present the growth aspects of these materials. We also present a simple model on the growth of InP on substrates of various orientations. The theoretically obtained temperature dependent growth rates are compared with the experimental values. Differential resistivities of semi-insulating lnP grown on substrates of various orientations as a function of temperature are also summarised."

Jan 1, 1998