Search Documents

By R. W. Cahn, C. D. Graham

The rate of growth of a single grain growing into a strained aluminum single crystal, measured by the conventional heat-cool-etch technique, is shown to decrease with time at temperature. The growth rate measured by means of X-rays, with the sample continuously at temperature, is found to be linear. Evidence is presented to show that the decreasing growth rate obtained by the conventional technique is due to abnormal recovery in the strained grain, and that the recovery in turn results from the heating and cooling cycles, rather than from the effects of etching. The experimental apparatus is described in an appendix. FREQUENTLY, the rate of grain boundary motion during recrystallization is determined by heating a sample to a known temperature for a given time, cooling to room temperature, and etching to reveal the boundary position. The cycle of operations is repeated as many times as necessary to establish the rate of boundary motion. Although this heat-cool-etch technique has been used by a number of workers over a period of many years,'-!' other investigators have encountered difficulty with the method."'. " They have attributed the erratic results to the effects of repeated heating and cooling, or of etching, or both, and have adopted an alternative experimental procedure in which a number of identical samples are employed, each sample being cooled and etched only once. This alternative method ove1.comes some difficulties, but introduces others. In particular, the incubation periods of the observed grains are unknown: any effect of crystal orientation on growth rate cannot be determined easily. A preferable method would be to measure the motion of a recrystallizing grain boundary with the sample at temperature without etching," but such measurements have in the past been restricted to nonmetals. This paper describes the construction and operation of a device, the goniometer furnace, with which the position of a moving grain boundary between a recrystallizing grain and the strained single crystal into which it grows can be measured by means of X-rays, with the sample maintained continuously at temperature. Goniometer Furnace The operating principle of the goniometer furnace is shown in Fig. 1. The sample, in the form of a bicrystal strip, is surrounded by a furnace, not shown in the sketch, and can be rotated about the two axes A and B which intersect at the point where the X-ray beam strikes the strip. The strip is oriented so that one of the two grains gives a strong Bragg reflection, which is detected by a suitably placed Geiger-Miiller counter coupled to a counting-rate meter When the strip is moved parallel to its own length in the furnace, arrow C, so that the X-ray beam strikes the second grain, there is in general no strong reflection. By noting the position of the strip at which the drop in Geiger counter reading occurs, it is possible to determine the position of the boundary. Measuring the change in boundary position with time at temperature gives the rate of growth of the recrystallizing grain. Details of the construction and operation of the goniometer furnace are given in the Appendix. Measurements showed that the temperature in the furnace was uniform within ±10°C over its working length of about 28 cm. The temperature at the measuring position, i.e., at the point where the X-ray beam struck the sample, was estimated to be constant within ±2oC. Using the goniometer furnace, the position of a stationary boundary could be measured with a reproducibility of ±0.3 mm. At elevated temperatures, 500" to 625"C, with the boundary in motion and the X-ray reflection less sharp, the estimated accuracy of each measured boundary position dropped to about ±1 mm. Experimental Results The test pieces were single crystals of 99.6 pet A1 —principal impurities 0.19 pet Fe and 0.12 pet Si— 1 mm by 1 cm in cross section and 6 to 10 cm in length, grown by the strain-anneal method. This relatively low purity material was used because of the difficulty encountered in producing strain-anneal single crystals of very high purity—99.996 pet—

Jan 1, 1957

By Hemendra N. Kalia

To plan a safe and efficient coal mining operation, the design engineer should use all the available information regarding the property to be exploited. The reliability of the mining operation must be as high as possible so that the plants relying on the coal can operate at the maximum design capacity. A good design should incorporate all of the known geological characteristics of the deposit, the structural and physical properties of the coal, as well as the rock which will form the roof and floor of the mine openings. A systematic method is proposed as a guide to insure a mine design that will be safe, efficient and will minimize surface disturbances resulting from mining operations. It is anticipated that the method proposed will result in maximum extraction at perhaps minimum cost to the operator. In general, to develop a mining area, several factors are systematically reviewed: (1) determination of the economic minability of the deposit, (2) the computation of the coal reserves, (3) the marketability of the coal, and (4) the life of the property. In general, boreholes are drilled in a predetermined pattern and geophysical or geological methods are used to log the boreholes. The information so obtained is primarily used to determine the quality and the extent of the deposit and to determine to some extent such geological features as faults, barren areas, washouts, and channels.

Jan 1, 1973

By A J. Cornah

Critical decisions in iron ore project evaluation and production are based on global and local spatial estimates of primary mineral deposit properties (such as in situ geochemical grades) and geometallurgical responses (such as screened, washed or concentrated product yields and grades), which are derived from limited sample data. These spatial estimates are typically made using classical geostatistical techniques, which fundamentally assume that the attributes of interest behave additively. This assumption is generally appropriate for æprimaryÆ variables but æresponseÆ variables may behave non-additively and therefore their direct linear estimates may be biased.In this paper an existing additivity testing mechanism is used to quantify the bias resulting from direct linear estimation of a non-additive iron ore attribute. Data from a magnetite project are used to determine the circumstances under which such biases may be of material impact. The implications for iron ore resource estimation, geometallurgical modelling and grade control are outlined and discussed.CITATION:Cornah, A J, 2013. Assessment of the impact of non-additivity in the estimation of iron ore attributes, in Proceedings Iron Ore 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By W. D. Riley

Engineered Scavenger Compounds (ESCs), developed by the U. S. Bureau of Mines I are a novel class of compounds that can selectively recover a desired element from 'a solid or molten alloy. Lithium titanate (Li2Tip7 or Li20' 3TiO.) is being used as an ESC to recover lithium (Li) from Aluminum-Lithium (AI-Li) alloys. X-ray diffraction measurements have shown that lithium titanate undergoes a phase change from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of Li in the matrix of the material and the effect of temperature. Although both of the structures are metastable, the hexagonal phase that forms during the scavenging of Li from AI-Li alloys appears to be the more stable phase. Recovering Li from the ESC by electtodeposition does not cause the structure to revert to the orthorhombic phase. Both the orthorhombic and the hexagonal structures of Li.Til07 have similar scavenging capacities for Li. This paper proposes a new mechanism for the phase transformation.

Jan 1, 1991

By W. K. Collins

Engineered Scavenger Compounds (ESCs), developed by the U.S. Bureau of Mines, are a novel class of compounds that can selectively recover a desired element from a solid or molten alloy. Lithium titanate (Li2Ti3O7 or L'20-3T'02) is being used as an ESC to recover lithium (Li) from Aluminum-Lithium (Al-Li) alloys. X-ray diffraction measurements have shown that lithium titanate undergoes a phase change from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of Li in the matrix of the material and the effect of temperature. Although both are metastable, the hexagonal phase that forms during the scavenging of Li from Al-Li alloys appears to be the more stable phase. Recovering Li from the ESC by electrodeposition does not cause the structure to revert to the orthorhombic phase. Both the orthorhombic and the hexagonal structures of Li2Ti3O7 have similar scavenging capacities for Li. This paper proposes a new mechanism for the phase transformation.

Jan 1, 1993

By M. A. Schimmelpfennig, A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to longer travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation may be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways may contribute to formation. This study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Co. to identify causes of the problem.

Jan 1, 1984

Recent advances in GPS, machine guidance technology and telemetry allow an unprecedented level of control of surface mining operations. GPS technology can now locate the bucket of a shovel or the blade of a dozer within 50mm (2 inches).Some of the outcomes possible are: precise selective mining – even when the ore is visually indistinguishable from waste: tracking grade and tonnage of every ore parcel through the mine: real time productivity monitoring: detailed post accident safety analysis: tracking the movements of every piece of equipment. This paper will consider the contribution that GPS based machine control systems can make to ensuring that surface mining projects deliver the outcomes promised in the feasibility studies. Case studies of installations are presented.

Jan 1, 2004

By William H. Lane

After a number of years of engineering and operating assignments and through many types of evaluations, the need for a simple analytical method of evaluating mine haulage alternatives became obvious. Haulage, like 50 many other facets of mining, is generally a sequence of interconnected events that change, often drastically from mine to mine. Often the operator or the mine engineer has neither the time, manpower, facilities, or information needed to prepare a detailed evaluation. For many studies or for routine variance analysis, that detail may not be necessary. The intent of this article is to present an approach for analyzing mobile mine haulage that is simple and straight-forward. These methods are not designed to replace more formal and detailed procedures that have been developed previously and are available in our technical libraries. They are offered as a tool to be applied to preliminary designs, feasibility studies, and variance analyses where more complete detail is not warranted. These methods will eliminate combinations that are not economical or appropriate before more intensive and complete evaluations are undertaken. These methods may also be used to evaluate ongoing operations and to plan changes in those operations. This presentation describes a series of steps that have evolved for the handling of haulage evaluations. It concentrates on the factors having major impact on the results. Because the approach is a sequence of distinct steps, a case study was chosen as the best method of presentation. This case is a composite of several actual situations that have been encountered within the last few years.

Jan 1, 1978

By Mark Samonds

"Manufacturing processes which involve liquid to solid and solid state transformations in metals encompass a wide variety of physical phenomena. The past twenty years have seen a steady evolution in the complexity and scope of numerical models of these processes, beginning with thermal analyses without phase change. Recently, a few software packages have become available which have true multi-physics capabilities. This permits the treatment of thermal, fluids, stress, electromagnetic, chemical reaction and microstructure development aspects altogether in a fully coupled simulation. This paper will consider various aspects of these types of models.Coupled thermal and fluid flow analyses of continuous castings have been around for fifteen years. Coupled thermal and free surface fluid flow simulations of shape castings have been available for ten years, including view factor radiation models for investment castings. Only recently, however, have fully coupled thermal, fluid, and stress analyses become practical. This implies the reverse coupling of the mechanical deformations to the solution of the energy and momentum equations through modification to the interface heat transfer coefficients and the fluid domain geometry. This has been implemented with a combined eulerian-lagrangian finite element method. Appropriate mechanical constitutive models will also be discussed.Many types of defects need to be predicted in casting processes. Those related to stress include hot tearing, hot cracking, part distortion, and thermal fatigue in dies. Macroporosity, microporosity, and microsegregation are determined by the solidification behavior and microstructure development in a casting. In particular, microporosity is influenced by dissolved gases, the morphology of the mushy zone, the liquid to solid density change, and the local pressure conditions. Macrosegregation is caused by the partitioning of solutes during. solidification and subsequent thermo-solutal convection. An additional transport equation is required for each solute that is being tracked. Computational thermodynamics is being incorporated into these types of analyses to determine transformation temperatures, partition coefficients, densities, and enthalpies. In combination, the microstructure and microporosity models can frequently predict a variety of mechanical models, such as yield strength, tensile strength, and elongation."

Jan 1, 2001

By V. Aprahamian, G. B. Harris, C. W. White, M. Tangen

"In 2005, the Royal Canadian Mint (RCM) commissioned a new silver electrorefining circuit. This circuit was intended to operate with a minimal electrolyte bleed for the control of copper. However, by the time of start-up, the levels of copper-rich silver doré to electrorefining had increased, and despite partial pyro-conversion in a small Top Blown Rotary Converter (TBRC), copper concentration in the silver anode still averaged 7.5%. This necessitated frequent replenishment of the electrolyte with fresh silver nitrate since copper displaced dissolved silver during electrolysis, and therefore requiring a robust copper bleed treatment step in order to maintain cathode silver flake purity at 99.99%. The originally-installed bleed treatment system could not meet the RCM’s needs. A thorough review of known technologies, however, did not indicate one capable of handling the copper load, and resulted, therefore, in the development of a novel copper hydrolysis approach for removal of copper as an insoluble basic nitrate salt, and recovery of the associated nitric acid for re-use in the circuit. Laboratory-scale trials showed reproducible results, and existing equipment was subsequently modified.INTRODUCTIONIn 2005, the introduction of a new silver electrorefining circuit at the Royal Canadian Mint (RCM) initiated changes in the way customer silver, collected from the gold doré circuit, was processed. These circuit changes were discussed in a recent paper (Aprahamian, 2015). A wastewater treatment plant had not been budgeted at the time, and this represented a significant constraint when considering the introduction of a wet processing circuit. After a review of various options, a turnkey silver electrorefining circuit was purchased from a European firm. Initially, enough cells were ordered to produce 2 million oz of fine silver (999), with the option to increase to 5 million oz. The selected equipment was based on a Moebius cell design combined with a silver grain pressure dissolver to produce make-up silver nitrate solution. Additionally, an evaporator/hydrolysis unit included in the package appealed to the Mint Refinery, on the basis that it offered a simple way to bleed dissolved copper in electrolyte without generating effluent."

Jan 1, 2016

By S Robson, T G. Blenkinsop, S C. Dominy

Golden Pig mine is in the central part of the Southern Cross greenstone belt within the Archaean Yilgarn craton. The mine has produced approximately 2.5 Mt of ore at 5.7 g/t Au to yield approximately 450 000 oz. The majority of gold mineralisation is hosted within extensively deformed and quartz-veined BIFÆs. In addition to the BIF-hosted mineralisation, an increasingly important part of the resource lies in the Taurus Lode, which is a N-NNW-trending amphibolite facies shear zone. The Taurus Lode lies within a continuous shear-zone that has a moderate to steeply WSW dipping foliation, and a mineral lineation of biotite, amphibole and pyrrhotite plunging consistently 10¦ S. Drive faces, subperpendicular to the foliation and lineation, consistently show evidence for syn-mineralisation reverse shear. Exposures parallel to the mineral lineation and perpendicular to the foliation reveal both sinistral and dextral asymmetries. These characteristics suggest that the vorticity axis of the Taurus Shear Zone is parallel to the mineral lineation, and that the simple shear sense is reverse. This geometry can arise when there is a major component of flattening across the shear zone, which may be due to interference between two adjacent granite domes. The BIF-hosted lodes plunge consistently 15¦ NNW coincident with the intersection of the axial planar cleavage of the regional folds and the Taurus Shear Zone. However, where the penetrative shear characteristics control the orientation and geometry of the mineralisation, oreshoots plunge SSW, parallel to the stretching and mineral lineations within the shear. The SSW plunge of strike extensive and laterally confined high-grade, economic ore shoots within the Taurus shear is fundamental to defining the economic mineralisation within this lode. Identifying the zones of maximum continuity and establishing the optimal position for future development will maximise ore extraction.

Jan 1, 2003

By Frederick J. Pope

The protaxis of the North American continent consists, as is well known, of a large V-shaped area of Archæan rocks, which lie for the most part in the Dominion of Canada, and occupy an area of not less than 2,031,000 square miles. The western limit of this area extends from 'Lake Superior in a northwesterly direction to the Arctic Ocean, the southern is found along the Lower St. Lawrence as far as Labrador. A minor area, spoken of as the Adirondack region of northern New York, has a somewhat broken connection with the main body in a narrow band of igneous rock, which crosses the Upper St. Lawrence where it leaves Lake Ontario. The ancient crystallines are also presumably beneath all the later sediments, hut the above brief description outlines their principal exposures. This great rock-complex consists, for the most part, of a series of gneisses, which present great variations in both structure and composition. In certain sections areas of gneisses of the general composition of granite, and remarkably uniform in character, prevail. They consist largely, if not exclusively, of crystalline rocks in which a banding or foliation has been induced by pressure. These rocks constitute the basal member of the Laurentian system, and by later writers have been referred to as the Ottawa gneiss. In other and quite extended areas, gneisses, regarded by many as composed of altered sediments, are associated with crystalline limestones, quartzites, and much injected igneous matter. To this series the term Grenville has been applied. Both of these series of gneisses are penetrated by various igneous masses, of which the most important are great intrusioiis of several members of the gabbro family, such as anortho-sites, norites, pyroxenites, and gabbros proper; the whole form-

Jan 1, 1900

By W. G. Spencer, E. Sulis, P. M. Tiley

"Dome Mine's No.8 shaft is located about 1 km northeast of Dome's No.3 shaft and mill complex in South Porcupine, Ontario.No.8 shaft was brought into production in 1984 to hoist ore and waste for the complete mine as well as to service the mine from the 1600 level and below. Access above 1600 level is provided by No. 3 shaft.The rectangular shaft has six compartments consisting of two skips, a cage, counterweight, manway, and a service compartment. The over-all size of the shaft is 14 ft 7 in. by 20 ft by 7 in. (Fig. 1). A 7th compartment for shaft deepening is incorporated in the bottom 500 ft of shaft. The shaft is 5470 ft deep. The loading pocket is located at 5300 ft and the dump 61 ft below the collar.Surface facilities consist of a concrete headframe and a structural steel hoistroom which houses the cage and production hoists . The service hoist is a 12-ft diameter double drum, with one 1750 HP DC motor, and the production hoist is a 15-ft diameter double drum with twin 1750 HP DC motors.Both hoists have a single clutch and a single reduction gear train built by Orenstein & Koppel, and equipped with Canadian General Electric drives. The cage hoist is equipped with a disc pinion brake.The skips were originally aluminum 14-ton capacity, Rolla-chute design with steel liners on three sides and 4 in. of rubber on the back, to absorb the loading impact. The original guide rollers consisted of fixed 10 in. pneumatic tires. The face-to-face units were eventually replaced with larger airplane-type tires mounted on a spring loaded pivot arm."

Jan 1, 1993

By D. R. Parrish, V. J. Berry

Reverse combustion is one thermal method of recovering hydrocarbons from porous undergrortnd formations containing oil or tar. In applying this method, air is introduced via an injection well and the mixture of air and hydrocarbons is ignited in the production well. A combustion zone then recedes toward the injection well, counter-current to the air flow. If the combustion-zorie temperature is sufficiently high, the oil or tar irz place is distilled arid cracked. The hydrocnrhon flows as a vapor to the production well and subsequently is condensed at the surface. Maximum temperature and velocity of morcment arc the two dependent variubles defining the progress of the combustion zone. A theoretical analysis has been made of heat flow in the reverse-comhustion process as.srtrning linear flow in a homogeneous system. The differentirll equatious, which include the oxygen-hydrocar-hon rctrction rate, have been solved numerically. Rescllts indicate that the maximum temperature reached and he cornbustion-zone relocity both increase with an incrense in air-injection rote. Heat loss to surroundings has little effect on the maximum comhustion-zone ten?perature achieved, but it is reflected in a reduced com-bustion-zorzc, velocity. It is also predicted that an increase in the oxygen-hydrocarbon reaction rate results in a reduction in the maximum temperature reached. The calculated results are in agreement with results from reverse-combustion experinments using samples of a tar sand. INTRODUCTION Reverse combustion is one thermal method of recovering hydrocarbons from porous underground forma-tions containing oil or tar.' In applying this method, air is introduced into the underground formation via an in-jection well. In one or more adjacent production wells, the mixture of air and hydrocarbons is ignited at the sand face. The combustion zone thus formed recedes toward the injection well, counter-current to the air flow (Fig. 1). Under certain conditions, the rate of recession of the combustion zone is sufficiently rapid that only a small fraction of the hydrocarbon at any point in the formation is consumed by combustion. If the combustion-zone temperature is sufficiently high, the uncon-sumed oil or tar in place may be partially distilled or cracked. This material then can flow as a vapor with the gaseous combustion products to the production well and subsequently be condensed at the surface. Under other conditions, the combustion-zone temperature may be so low that little, if any, of the hydrocarbon is vaporized. Nevertheless, the viscosity of the hydrocarbon may be reduced enough so that other recovery methods subsequently can be applied to produce oil at attractive rates. The maximum temperature achieved in the combustion zone and the velocity of movement are the two dependent variables defining the progress of the combustion zone. Presumably. knowledge of these factors will permit estimates to be made of oil recovery efficiency, oil and gas producticn rates and average amount of injection air required per barrel of oil recovered. The maximum temperature and combustion-zone vclocity are, in turn, expected to be dependent upon air flow rate, heat losses to surrounding formations, physical properties of the rock and the hydrocarbon. the extent to which the porous formation is saturated with the hydrocarbon, the rate of oxidation of the hydrocarbon and the amount of heat released. It is desirable that the relative importance of each of these factors be understood so that the results of laboratory tests of oil recovery by reverse combustion can be properly interpreted in terms of expected field performance. It is particularly desirable to assess the importance of heat lcsses because these are difficult to control or eliminate

By Dengfu Chen, Huabiao Chen, Yunwei Huang, Mujun Long, Youguang Ma, Lintao Gui

In the current work, a three-dimensional model coupling turbulent flow, heat and solute transport was developed to investigate the solute transport and redistribution in the mold of slab continuous casting where the Reynolds number is very high and the molten steel flows strongly. The conservation equations of momentum, energy and species for a multicomponent system which includes solute element C, Si, Mn, P, S were solved with the commercial software ANSYS Fluent. The parameters used in the model are based on the actual continuous casting. The fluid flow, temperature distribution and solute elements distribution were analyzed. Results showed that negative segregation occurred near the strand surface, and the species concentration reached a peak value at the solidification front during solidification. The segregation degree of solute element S is higher than the other solute elements because of its lower equilibrium partition coefficient. The species concentration in the liquid pool is homogeneous because of the turbulent flow effect.

Jan 1, 2015

By C. Bazin, B. Girard

The application of time series analysis techniques to plant data provides a method for examining and modeling the behavior of operators during the operation of furnaces for the reduction of ilmenite concentrate. The obtained model is used to assess the consistency of actions carried out by the operators and to review and improve the training procedures.

Jan 1, 1996

By Reynold Q. Shotts

Nitric acid oxidation rate analyses of three coals, previously studied microscopically by the Bureau of Mines, revealed three components. Relative quantities agree with those found for the four components given by the Bureau and results are consistent with current ideas of coal constitution. Possible multi-component composition for bright coal and a reactivity-rank relation are suggested.

Jan 5, 1953

By X. K. Jiang

Pneumatic, triboelectrostatic processing of physical mixtures containing fine (-200 mesh) particulate may have significant application potential in the mining and energy industries. Such dry processing methods, especially for finely comminuted materials, have not been examined in as much detail as wet processing methods nor have been part of the training or education of mining and process engineers. We have examined fundamental and applied physical and engineering factors controlling triboelectrostatic beneficiation of fine-sized physical mixtures, one of which -combustion fly ash -has size, heterogeneity and mineral concentrations typical of those expected in mined minerals. The applicability of dry processing, however, cannot be readily evaluated because of the unavailability of standard procedures for process assessment.

Jan 1, 1999

By H Höft

Today tunnel segment liners are sealed with corner-vulcanised gaskets made of extruded elastomeric compression profiles. The profile geometries and the elastomeric materials have been further developed in course of time to meet the steadily increasing water-proofing requirements. After 40 years of using such compression gaskets, a wide range of proven standard profile geometries and well-known brands can be found on the market. Even so, there is still potential for further developments and improvement, not only with regard to the water-proofing performance. Permanently increasing cost pressure in the segment production plants demands further developments and new solutions with regard to application techniques. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

Bendigo Mining operates a 600 000 t/a comminution, gravity, flotation and leaching processing plant for the recovery of gold from their Kangaroo Flat Operation, in the Bendigo goldfields. The free gold and gold bearing sulfi des present are typically coarse grained and hence are highly amenable to gravity recovery. Plant operating data is consistently showing that over 78 per cent of the feed gold is recovered in a circuit, consisting of inline pressure jigs, inline spinners followed by free gold tabling and intensive leaching of tabling tails. The circuit receives coarse crushed product from high pressure grinding rolls and the grinding mill discharge, which allows material to be re-circulated through the gravity process until the particles are small enough to enter the flotation circuit. A plant audit was completed on 26 November 2009 designed to give an indication of the overall operational characteristics of the gravity circuit including single pass efficiencies of associated equipment. The techniques, results and challenges of such a survey are discussed.

Aug 1, 2010