Search Documents

By Arthur Knapp

The economics of fuel oil must be considered in two aspects; viz., fuel oil as one of a number of competitive fuels and fuel oil as a refined product of petroleum. "Fuel oil" is usually defined as that product of petroleum which is used in furnaces for the generation of heat by simple combustion. It is true that any product of petroleum used in an internal combustion engine is essentially a fuel oil, but such oils are not included in the class known as "fuel oil." Fuel Oil as One of Several Fuels For a number of years, the petroleum industry has believed that the petroleum reserves were very limited and that petroleum products would begin to become scarce within a few years. The industry has believed that there would be a gradual but continual rise in prices as a result of this impending scarcity. The industry, therefore, has informed the users of fuel oil thai., once they were eliminated by price, they were eliminated for all time. The petroleum industry believed and made the consumer believe that there would never be any appreciable recession in price which would make it

Jan 1, 1928

By G. J. Olson, K. S. Noah

A combined physical/biochemical process for the precombustion removal of 13 inorganic hazardous air pollutant (HAP) precursors, i.e., Sb, As, Be, Cd, Cr, Cl, Co, F, Pb, Hg, Mn, Ni and Se, from coal was tested. Biochemical processes for removal of HAP precursors from coal potentially offer advantages of deeper cleaning, more specificity and less coal loss. The slurry column is a second-generation process for the beneficiation o f fine (60-mesh x µm coal by a combination of physical separation of mineral matter and biooxidation of pyrite. Sixty-seven percent removal of pyrite from a 60-mesh Pittsburgh #8 coal was achieved at a 35% (w/w) slurry concentration and a five-day reactor residence time. Ninety percent of the heating value of the feed coal was recovered. Among the HAP precursors of most concern, over half of the Se, As and Hg were removed from the feed coal. From 40% to 70% of most HAP precursors were removed from the feed coal. Hg in the feed coal was reduced from 0.12 to 0.054 ,µg/g in the product coal, while waste coal contained 0.24 µg/g.

Jan 1, 2000

By J. D. Miller, M. Misra

The processing strategy for the effective separation of bitumen from low grade (<l0 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However, the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1981

By L. D. Hall, S. J. Rothman

The diffusion of lead and of trace amounts of bismuth in liquid lead have been investigated by the capillary method, using ROD and ROE as tracers. The results are compared with existing theories of diffusion in liquids, the agreement with theory being fair. The heat of activation for self-diffusion in lead is found experimentally to be close to the corresponding activation energy obtained from viscosity data. The pioneer data of Groh and von Hevesi for the self-diffusion of liquid lead, using ThB as a tracer, fit in with the present results. OMPARED with the volume of effort expended on solid state diffusion, there has been little attention paid to diffusion in liquid metals. A review of experimental work in this field, covering most of the studies up to 1951, was given by Jost.&apos; More recent papers include those by Hoffman2 on self-diffusion in mercury, Morgan and Kitchener" and Stark, Shchilishchev, and Kazachkev4 on the diffusion of various elements in liquid iron, and Grace and Derge on the diffusion of bismuth in bismuth-lead alloys. The need for more experimental data to aid in the evaluation of existing theories prompted the

Jan 1, 1957

By David C. Byrne

From an engineering perspective an ideal industrial noise control solution focuses directly on the actual source of the poise. Eliminating the noise-generating mechanism altogether obviates the need for other noise contra l treatments or hearing protection devices. However, in cases where attenuating the source is not feasible engineering controls must be oriented toward blocking the path that the sound waves travel toward employees. Acoustical enclosures are commonly used as sound path treatments to contain the noise from a machine: alternatively a control room/booth or equipment operator&apos;s cab may be used to isolate the worker from the noise. Anyone who has successfully used acoustical enclosures knows that the design procurement, and installation process is deceptively simple. Alt too often First-time efforts fait to account for many of the constraints that can render the enclosure essentially useless. Things that cannot be overlooked include: providing convenient worker access (physical and visual): allowing for proper machine operation/product flow; and supplying fresh air or preventing undue heat or contaminate build-up inside the enclosure. All of these factors must be given careful consideration, otherwise the enclosure will not perform adequately.

During the past year a number of significant advances in geostatistics have been published. These were presented at the 13th APCOM Symposium in Clausthal, Germany and at a NATO Advanced Study Institute on Geostatistics in Rome, Italy. Of greatest importance is the work that has been done in establishing methods which correctly predict the cutoff grade-tonnage curves, and the average grade of ore-tonnage curves for deposits in which ore and waste are intermingled. Grade-tonnage curves based on estimates made from widely spaced exploration data have been found to underestimate the grade of ore and overestimate the tonnage present. This problem has been remedied by the calculation of conditional probability distributions for the unknown grade of a block. Another advance has been made in the field of geostatistical estimation for deposits in which a trend is present. Previously a technique known as universal kriging has been used, which involves much subjective judgement as to the trend fitted. A new technique, generalized increments, allows computer estimation of such deposits with much less subjective judgement. Computational efficiency of geostatistical methods has continued to improve to a point where a geostatistical estimate can be obtained for little more than the cost of any other computerized method.

Jan 1, 1976

By Earle Schumacher

THE solidus line above the solid solution field in the lead-antimony system was originally determined by Dean and his associates1 from heating curves. They did not regard this line as having been accurately fixed and in their more recent publications2 the curves drawn do not follow closely the original data. The precise location of the solidus line is of importance in the extrusion of lead-antimony cable sheath, as the temperature of the metal in this process must be less than the lowest temperature at which any part of the alloy in the lead-press charge becomes liquid. It is very desirable, however, to operate at as high a temperature as possible, as the rate of extrusion for a given pressure is approximately doubled for an increase of 10° C. in temperature. The precise location of this line is also important, in the investigation of ternary systems of lead, antimony and a third metal. For these reasons, and because of the differences reported in the literature, data were secured on the lead-antimony solidus line by the classical quenching-test procedure.

Jan 1, 1927

By T. Thriveni, Ch. Ramakrishna, Ahn Ji Whan

Numerous reports and researches address the various environmental issues about the municipal solid waste incineration waste management of heavy metals and other particulate matters with the range of 10–2.5. Although in many developing and industrialization countries land fill with the disposal of municipal solid waste, open incineration has become a common practice. Bottom ash contains heavy metals including particulate matters. The investigation of size distribution for the heavy metals and particulate matters in the bottom ash is essential. However, ultra-fine particle size and heavy metal stabilization are the most important requirements for ecofriendly by products. There are wide variety commercial technologies available for monitoring PM 10, PM 2.5 and ultra-fine particles. In this paper, we reported the studies on physical and chemical characteristics of municipal solid waste incineration (MSWI) bottom ash containing particulate matter whose particulate sizes are lower than PM10, PM2.5 and heavy metal stabilization method by carbonation were investigated.

Mar 1, 2017

By Gregg J. Hodges

The Stillwater Mining Company, a partnership of The Pittsburg & Midway Coal Mining Co. and Manville Corporation, began commercial production of flotation concentrates from the western hemispheres&apos; only primary platinum palladium deposit at Nye, Montana in March 1937. In the fall of 1987 an integrated pilot plant testing campaign of electric furnace smelling and oxygen? blown converting confirmed the feasibility of further upgrading to semi? refined matte or &apos;white metal". In the summer of 1990 the production smelter was brought on-line at Columbus, Montana. This paper describes the technology transfer from the pilot to the production smelter. Emphasis is placed on flowsheet development and the scale factors between the test and production furnaces and gas cleaning plants. The metallurgical results of the pilot plant and of the early months of production of the commercial works are also compared.

Jan 1, 1991

By Yuan-bo Zhang, Gui-hong Han, Yan-fang Huang, Tao Jiang, Guang-hui Li

"Under isothermal conditions, the reduction behavior of oxidized pellets balled with bentonite was investigated with CO-CO2gas mixers in the temperature range from 900°C to 1100°C. The whole reduction of oxidized pellets was followed up by means of weight-loss technique. And the swelling index of pellets was examined by visualizing physical changes of pellet in a horizontal tube furnace. The results present that the reduction rate of oxidized pellets is increased with the increase of reduction temperature. While the swelling index is firstly increased and then decreased with the increase of reduction time and reduction extent, which can be ascribed to the disruptive stresses induced during the transformation of hematite to magnetite. The maximum swelling index is gradually increased with the increase of reduction temperature and CO content.IntroductionWith the rapidly development of iron and steel industry, direct reduction iron has been considered as one kind of high quality burdens in electric furnace steelmaking [1]. At present, ""Two-step"" coal-based direct reduction process, which employs oxidized pellets as raw materials, has been used in industrial production [2]. The reduction behavior of iron ore oxidized pellets has been becoming one of the most frequently studied topics in extractive metallurgy[3]. The heat and mass transfer in direct reduction processes results in a series of stepwise reduction reaction (hematite--magnetite--wustite--iron), accompany with the volumetric swelling of pellets[4]. A lot of literatures have been reported on the reduction model of ferrous oxides and swelling behavior of pellets. A. A. El-Geassy K, et.al [5-7] revealed that the reduction process was controlled by chemical reaction at early stage by employing pure Fe203 as raw materials and CO as reduction gas. Chen Y [8] made research on the reduction kinetics of porous oxidized pellets and obtained the rate constant and activation energy of at different reduction stage. In addition, the swelling and disintegration of iron ore pellets was affected by chemical composition of pellet and reducing parameters, which have been studied by numerous investigators [3,9, 1O]."

Jan 1, 2013

By Frederic P. Dewey

(New York Meeting, February, 1912.) By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called; platinum. Sometimes it is so, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes jives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid, 1 I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Apr 1, 1912

By Louis A. Carapella, William E. Shaw

MAGNESIUM and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitional point has been set at 225°C by Schmid1 for single crystals, and at 250°°C by Morell and Hanawalt2 for extruded magnesium metal. In a recent X-ray investigation on polycrystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional temperature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheett over a wide range of temperatures has been investigated by Weber and Vanden Berg,&apos; and their results are presented in Fig r. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Hargreaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Hargreaves constant S, was obtained by the integrated or intermittent loading procedure. The authors5 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformational loads. These findings have been applied

Jan 1, 1947

By R. Quentin Eades, Kyle Perry

"Surface mines continue to implement highwalls for several reasons, such as increasing recovery, improving margins, and justifying higher stripping ratios. Highwall stability is a complex issue that is dependent upon a variety of mining and geologic factors, and a safe design is necessary for a successful surface operation. To improve highwall stability, it is important to understand the connection between local geology and blasting.Explosives are employed throughout the mining industry for primary rock breakage. There are a number of controlled blasting techniques that can be implemented to improve highwall stability. These include line drilling, smooth wall blasting, trim blasting, buffer blasting, air decking, and presplitting. Each of these techniques have associated advantages and disadvantages. Understanding local geology is necessary for selecting the appropriate controlled blasting technique. Furthermore, understanding the limitations and conditions for successful implementation of each technique is necessary. A discussion of the impact of geologic conditions on highwall stability is provided. Additionally, discussion is provided for the successful incorporation of the controlled blasting techniques listed above, and the associated mining and geologic factors that influence the selection and design of controlled blasting plans. Finally, a new methodology is proposed.INTRODUCTIONExplosives are used throughout the mining industry as the standard for primary rock breakage, a critical part of the mining cycle. In 2015, the U.S.. consumed 2.2 million tons of explosives (Apodaca, 2015). The coal mining industry accounted for the majority of explosive consumption, accounting for approximately 63% of total explosives. The quarrying and nonmetal mining industries accounted for 12% of explosive consumption, and the metal mining industry accounted for 9% (Apodaca, 2015). This constitutes 84% of the explosives used in the U.S. However, the energy released during the detonation process is often in excess of that required to adequately fragment the surrounding rock (Jhanwar and Jethwa, 2000). This excessive energy, along with over confinement and poor blast geometry, will cause damage to the undisturbed rock mass beyond the intended boundary of the blast. This event is known as overbreak or back-break (ISEE, 2011)."

Jan 1, 2018

By Pei-xiao Liu, Han-jie Guo, Yan-xiang Li

The thermodynamic analysis on chromium ore pellets in solid reduction chromium process is carried out, and the result is validated by pre-reduction experiment of cold briquetted chromium ore. Polarization Microscope and SEM are employed to observe microstructure and element composition. The thermodynamic and experimental results reveal the reduction mechanisms at different temperatures in the SRC pre-reduction process.

Mar 1, 2017

By J. P. Dunlop

THE fact is notable though probably little known that the United States is the only nation obtaining and distributing through its Government bureaus any data pertaining to waste metals and drosses. Some foreign governments do issue reports relating to mine or smelter produc-tion of primary metals, but none gives in scope and detail the information published now by the U. S. Bureau of Mines and formerly by the U. S. Geological Survey; and this is despite the fact that the funds annually allotted for those purposes are insignificant in comparison with allotments for the preparation of data relating to other industries of like importance. The earliest data on the production of metals from secondary sources in the United States were-contained in a press bulletin issued by the U. S. Geological Survey on Jan. 4, 1909. The information published was that for the year 1907 obtained and compiled by C. E. Siebenthal, who was one of the first to visualize the growing importance of the scrap-metal industry. The National Conservation Commission had emphasized its opinion that the known domestic supply of certain kinds of the more important metals was being rapidly marketed and that while there was no immediate cause for concern it was best to conserve such resources. Not only had there been a lamentable lack of any data regarding the quantity of scrap metals available or used but also gross carelessness and indifference in the segregation, collection, and effective use of scrap material. Siebenthal realized that even approximately correct statistics of recoveries from the more important base-metal scrap and drosses were nearly as essential to both producers and consumers as the statistics of the output of primary metals. There were not then nor are there now sufficient funds for complete collection of data, nor was it considered the province of the Geological Survey to do more than determine approximately the recovery of secondary metals for use in supplementing those given for the primary metals. Undoubtedly the first bulletins issued did not give the full output, for it takes time to establish contacts for an inquiry covering so

Jan 1, 1928

By J. P. Dunlop

THE fact is notable though probably little known that the United States is the only nation obtaining and distributing through its Government bureaus any data pertaining to waste metals and drosses. Some foreign governments do issue reports relating to mine or smelter production of primary metals, but none gives in scope and detail the information published now by the U. S. Bureau of Mines and formerly by the U. S. Geological Survey; and this is despite the fact that the funds annually allotted for those purposes are insignificant in comparison with allotments for the preparation of data relating to other industries of like importance. The earliest data on the production of metals from secondary sources in the United. States were contained in a press bulletin issued by the U. S. Geological Survey on Jan. 4, 1909. The information published was that for the year 1907 obtained and compiled by C. E. Siebenthal, who was one of the first to visualize the growing importance of the scrap-metal industry. The National Conservation Commission had emphasized its opinion that the known domestic supply of certain kinds of the more important metals was being rapidly marketed and that while there was no immediate cause for concern it was best to conserve such resources. Not only had there been a lamentable lack of any data regarding the quantity of scrap metals available or used but also gross carelessness and indifference in the segregation, collection, and effective use of scrap material. Siebenthal realized that even approximately correct statistics of recoveries from the more important base-metal scrap and drosses were nearly as essential to both producers and consumers as the statistics of the output of primary metals. There were not then nor are there now sufficient funds for complete collection of data, nor was it considered the province of the Geological Survey to do more than determine approximately the recovery of secondary metals for use in supplementing those given for the primary metals. Undoubtedly the first bulletins issued did not give the full output, for it takes time to establish contacts for an inquiry covering so

Jan 1, 1928

By Adrian Villanueva

In this study, we compare the influence of two water soluble polymer-based organic binders added to bentonite, to form a hybrid-binder system for Iron Ore Pelletization. The kinetics of the agglomeration process and resulting properties of green pellets were analyzed, and examined in detail through Scanning Electron Microscopy (SEM) and Confocal Laser Scanning Microscopy (CLSM) analytical techniques. It was encountered that the differences in the mechanical properties of the pellets produced by each binder system could potentially be explained by the ability of the polymer to interact with bentonite at a macromolecular level.

Oct 30, 2017

By EDWARHD HALSE

Discussion of the Paper of Dr. H. M. Chance, presented at the Lake Superior Meeting, September, 1904. EDWARD HALSE, Puerto Berrio, Colombia, So. Amer. (communication to the Secretary*) : The Taviche mining-district is generally known as a Taviches," being named from the two villages called respectively San Pedro Taviche and San Jeronimo Taviche. It is so called by José G. Aguilera, in his paper on the Geographical and Geological Distribution of the Mineral Deposits of Mexico;&apos; and in published reports by the late N. W. Rudston Read ;2 and by Juan de Dios Villarello.3 The region is a large one, measuring about 24 miles long and 7 miles wide. Dr. Chance, in his interesting paper, tells us very little about the nature of the ores, and, with regard to the geology of the district, contents himself with observing that ? the country, as a rule, consists of eruptive rocks; and no evidences of sedimentary strata appear near the mines.? The latter part of the above statement is hardly correct. The formation is mainly eruptive, being hornblende-audesite of Tertiary age, which is limited on the east by the calcareous (Cretaceous) formation, and on the west by the Huronian rocks of Ocotlan. Limestone is seen close to the Santa Càtarina mine, at the northern end of the region. In the surface-working known as La Cueva, a little northeast of San Pedro, limestone forms the eastern wall of the deposit which consists of spots (moscas) of pyrargyrite in white opaque or transparent quartz. Ill one place the ore is associated with stibnite, and the quartz frequently exhibts a

Sep 1, 1905

By J. P. Dunlop

The fact is not.ablc though probably little known that thc Unitcd Statcls is the only nation obtaining and distributing through its Govcrn-ment burcaus any data pertaining to waste metals and drosses. Some foreign goverrlnlents do issuc reports relating to rnine or smelter production of prirrlar~ metals, but none gives in scope and detail t&apos;he information published now by the U. S. Bureau of Mines and formerly by the U. S. Geological Survey; and this is despite the fact that the funds annually allotted for those purposes are insignificant in comparison with allotments for the preparation of data relating to other industries of like importance. The earliest data on the production of metals from secondary sources in the United States were contained in a press bulletin issued by the U. S. Geological Survey on Jan. 4, 1909. The information published was that for thc year 1907 obtained ant1 compiled by C. E. Siebenthal, who was one of the first to visualize the growing importance of the scrap-letal indust,ry. Thc Nationd Conscrvation Commission had emphasized its opinion that the known domestic supply of certain kinds of the morc important irietals was being rapidly marketed and that while there was no immediate cause for concern it was best to conserve such resources. Not only had there been a lanlentable lack of any data regarding the quantity of scrap inetals available or used but also gross carelessness and indifference in the segregation, collection, and effective use of scrap material. Siebenthal realized that even approximately correct statistics of recoveries from the more important base-metal scrap and drosses wcrc nearly as essential t,o both producers and consumers as the stat&apos;istics of the output of primary metals. There were not then nor are there now sufficient funds for complete collection of data, nor was it considered the province of the Geological Survey t&apos;o do more than determine approximately the recovery of secondary metals for use in supplementing those given for the primary metals. Undoubtedly the first bulletins issued did not give the full output, for it takes time to establish contacts for an inquiry covering so

By J. P. Dunlop

THE fact is-notable though probably little known that the United States is the only nation obtaining and distributing through its Government bureaus any data pertaining to waste metals and drosses. Some foreign governments do issue reports relating to mine or smelter production of primary metals, but none gives in scope and detail the information published now by the U. S. Bureau of Mines and formerly by the U. S. Geological Survey; and this is despite the fact that the funds annually allotted for those purposes are insignificant in comparison with allotments for the preparation of data relating to other industries of like importance. The earliest data on the production of metals from secondary sources in the United States were contained in a press bulletin issued by the U. S. Geological Survey on Jan. 4, 1909. The information published was that for the year 1907 obtained and compiled by C. E. Siebenthal, who was one of the first to visualize the growing importance of the scrap-metal industry. The National Conservation Commission had emphasized its opinion that the known domestic supply of certain kinds of the more important metals was being rapidly marketed and that while there was no immediate cause for concern it was best to conserve such resources. Not only had there. been a lamentable lack of any data regarding the quantity of scrap metals available or used but also gross carelessness and indifference in the segregation, collection, and effective use of scrap material. Siebenthal realized that even approximately correct statistics of recoveries from the more important base-metal scrap and drosses were nearly as essential to both producers and consumers as the statistics of the output of primary metals. There were not then nor are there now sufficient funds for complete collection of data, nor was it considered the province of the Geological Survey to do more than determine approximately the recovery of secondary metals for use in supplementing those given for the primary metals. Undoubtedly the first bulletins-issued did not give the full output, for it takes time to establish contacts for an inquiry covering so

Jan 1, 1928