Search Documents

By Robert W. Bergwall

The $58,000,000.00 Columbia Heights Metro Station project (Section E3-a) forms a part of the Washington Metropolitan Area Transit Authority's (WMATA) Greenbelt Route - Green Line subway system. The Greenbelt route is one often segments that make up WMATA's subway system. Construction of the "cut and cover" reinforced concrete station includes 600 linear feet of an underground center platform, two ancillary service areas totaling 466 linear feet, two surface entrances, and vent shafts (See Figure No. 1). Station subgrade is approximately 60 feet below existing grade. The project can be divided into five main areas: 1. North Service Rooms and Passageway; 2. West Entrance and West Passageway; 3. East Entrance; 4. Center Platform; 5. South Service Rooms. Station dimensions are approximately 1068 feet long by 64 feet wide. Construction commenced at the site in January of 1995 and is expected to be completed by December of 1999. Franki Northwest Company, Crofton, Maryland, was awarded a subcontract by general contractor Blake Construction Company, Washington, D.C, to install the support of excavation and temporary decking systems. Franki's scope of work included the installation of 490 drilled soldier piles plus two elevator shafts totaling 29,700 linear feet of drilling; 1,150 tons of steel decking covered by 37,000. square feet of precast concrete deck planks; 120,000. square feet of timber lagging; 2,500. tons of struts and wales; and temporary support of underground utilities. In conjunction with Franki's work, Bencor Corporation of America, Dallas, Texas, constructed parallel, 600 foot long slurry walls which serve as permanent walls for the center platform portion of the station.

Jan 1, 1997

By E. H. Henderson

MR. R. V. NEILY stated that he had at one time operated at Goldenville. The practice and results are much the same now as in the olden days. Inside plates were then found to be a source of trouble and had been removed. At the Libbey mine, Queen's county, the sulphides carried considerable gold, and $45.00 to $60.00 per ton had been recovered from the concentrates by roasting and chlorinating. Later, concentrates were treated with bromocyanide. Following that practice, a cyanide leaching plant was installed, which did not require concentration of the tailings. Cyanidation brought a recovery of around 95 per cent, with but $300 worth of plant. In Nova Scotia, the ore of each locality presents an individual problem of its own as to treatment required. Ma. W. B. Timm stated that, in the majority of Nova Scotia gold ores, more than 75 per cent of the gold content is free-milling and, naturally, stamps are most efficient for collecting and amalgamating this gold. In Ontario and the West, they had got away from stamps, and perhaps the main reason was that the supply of battery-men, who came from Nova Scotia, had died off. Ball-mills had been installed, which required smaller space and handled large tonnage, even though, as far as amalgamation goes, the stamps were probably more efficient. If concentration is to be done, ore from stamps is usually in better shape for recovery in passing over the tables, as there is no slime. With the ball-mill, flotation is necessary. The better practice, undoubtedly, is to take out what gold is possible before it is all smashed up, as in the ball-mill, though recent developments in the ball-mill make it possible to trap and take coarse gold directly from the mill. In this way, cyanidation is speeded-up, due to saving of the time the coarse gold would take before going into solution. PROFESSOR A. E. FLYNN found it unusual in these days to read anything in favour of the stamp mill, and thanked Mr. Henderson for the excellent paper in which he upholds the stamps and backs his opinion with facts from actual operations. For the typical Nova Scotia ore, containing coarse gold, stamps are un¬excelled. It used to be said that the virtue of stamps is that they brighten the gold for amalgamation. Although this saying is almost classical, it is not true, for gold is never brighter than in the native, untouched state. Any hammering that gold gets makes it more difficult to amalgamate.

Jan 1, 1935

By José Fagundes Junior, Cleudson dos Santos Rego, Bruno Bastos da Silva Murad, Vitor Borlot Borba

Since the startup in 2002, the Hot Strip Mill at ArcelorMittal Tubarão has increased gradually the coil output as the customers demand new and more resistant dimensionally challenging (thinner and/or wider) steel grades. As a critical feature for customer applications, improvements have been carried out aiming a higher thickness performance and reduction of internal losses while still meeting the more restrict tolerances booked by the customers. This paper presents the recent thickness performance evolution since 2017 and the main actions deployed to improve it.

Oct 1, 2019

By William Billiet

"The Dulles Silver Line Phase II is an 11.4 mile extension of the Washington Area Metro Transit Authority’s Silver line in northern Virginia. There are three miles of elevated guideway, which are supported on 188 large diameter mono-shafts founded within the Triassic Geologic Aged Culpeper Fault Basin. Three lateral load tests were performed on fully instrumented test shafts. The challenge in developing the load testing program was how to reproduce the effects of the extremely high design loads along the test shafts, considering the limitations of the load test equipment. Development, execution, and analysis of the lateral load test program is discussed.INTRODUCTIONPlans for Dulles Silver Line Phase II include two Aerial Guideway sections on elevated track, the Main Line and Yard Leads. The Aerial Guideways are supported on mono-shafts (single, largediameter drilled shafts) socketed into rock. Lateral loads are resisted primarily through the stiffness of the shaft and the geotechnical resistance of the rock socket. The monoshafts were designed in accordance with AASHTO LRFD 2014. Based on our preliminary analyses, the production mono shafts were expected to consist of 6.5, 7.5, and 8.5 foot diameter drilled shafts with rock socket lengths varying between 8 and 34 feet (averaging 14 feet). Table 1 summarizes the maximum service load combinations for each size production shaft along the aerial guideway alignment.GEOLOGYThe project is located within the Piedmont Province, a major physiographic province on the east coast of the USA extending from Alabama to Pennsylvania. Within the Piedmont, a number of Mesozoic basins formed in rift valleys. Dulles Airport is located in the Culpeper Basin, characterized by a relatively shallow siltstone rock surface compared to the adjacent areas underlain by Piedmont crystalline rocks. The geologic stratigraphy at the load test sites generally consist of residual soils and intermediate geo-material (IGM) overlying siltstone rock. IGM is a term used by Virginia Department of Transportation (VDOT) to describe residual material as it transitions between soil and rock. For the purposes of the load test, the siltstone rock is classified as fractured rock (RQD<50), and competent rock (RQD=50). Table 2 summarizes the stratigraphy encountered at each test site."

Jan 1, 2017

By Sanai Nakabe

Japanese wartime economy demanded domestic cobalt production. This paper describes a process operated for two years at the Besshi mine and smelter on extremely low grade (0.1 pct Co) pyrite concentrates obtained from copper ore. &apos;The steps in the process were roasting, leaching, precipitation, reduction fusion to crude cobalt, and finally refining by electrolysis to 99+ pct. COBALT ore deposits in Japan are all small and of poor grade. In the past, a small amount of cobalt has been produced from the best portions of a few of these deposits, and very little production is expected in the future. In addition to these lean cobalt ores, cobalt is present in the cupriferous pyrite which is fairly abundant although of low grade, as is shown in Table I. Considerable cobalt is expected from these deposits because of their extent. Cobalt cannot be exclusively recovered economically from ore of this type; however, if means could be devised to recover it as a byproduct of copper production, a fairly large production at reasonable cost could be expected from Japanese sources. It was along this line that the research work was done. Selection of Suitable Process The process for extracting cobalt differs from ore to ore according to their composition. The difficulty in cobalt metallurgy arises from the fact that chemically cobalt resembles many such common metals as Mn, Fe, Ni, Cu, and Zn, associated with it in the ores. In the present case the most serious difficulties were: 1—Extremely low grade ore, 0.1 pct Co. 2—The large proportion of iron accompanying cobalt and its close similarity in chemical behavior. 3—The fairly large proportion of zinc and manganese and their chemical similarity to cobalt. The recovery of cobalt oxide as a byproduct of the hydrometallurgy of copper had been attempted in Japan but was stopped after a short period because it proved uneconomical. The literature disclosed no method for the recovery of cobalt from cobaltiferous copper pyrite and it was therefore necessary to devise a new process. The following basic principles were considered in selecting the process: 1—A major alteration in copper production methods should not be necessary. 2—The first step should be the extraction of cobalt leaving the large quantity of iron unaffected. For this purpose wet metallurgy would be preferred.

Jan 1, 1952

THE Institute of Metals Division opened its series of meetings by a session* on lead, R. S. Dean be-ing in the chair and G. 0. Hiers acting as vice-chairman. A large and representative audience listened to the papers in the abstract and contributed an inter-esting and fruitful discussion. The main points of these papers and discussion are given below: In the absence of Carl E. Swartz, the summary and conclusions of his paper, "A Study of the Lead-Tin-Cadmium System with Reference to Their Use as Solders," were read. Swartz investigated a number of alloys in the lead-tin-cadmium system and prepared a diagram representing the solidification ranges of these alloys. He also made tensile strength tests of joints made with these alloys, and compared these with joints made with ordinary lead-tin solder. The tests showed solders containing cadmium were equally strong as the lead-tin series and that the cadmium alloys were suit-able in other respects for use as solders. In general, solders of the composition near to the ternary lead-tin-cadmium eutectic appeared to be the best for most soldering work although compositions widely differing are desirable for special purposes. The lead-tin-cad-mium solders are finding a market particularly in the fields requiring lower solidification temperatures than common solders. Mr. Darby opened the discussion and asked whether it was a fact that the lead-tin-cadmium solders were more useful than ordinary solders on galvanized and tin-plated sheet. C. Smith said he thought it to be a fact that galvanized sheet was more easily soldered by the lead-tin-cadmium solders than common lead-tin-solder. Continuing, Mr. Smith showed lantern slides of his own investigation of the thermal diagram and recommended the 70 per cent lead, 20 per cent cadmium, and 10 per cent tin for general employment. He thought the author did not differentiate between wetting and alloying and pointed out that wetting was more a ques-tion of the flux than the metal. In some cases a definite alloy was formed by soldering and in some no evidences of alloying were found. Illustrating the former case he showed slides and demonstrated that failures always took place longitudinal with the brittle compound alloy and transversely across the solder itself.

Jan 3, 1928

By Robert K. Warner

When a new mine is opened, and often when an operating mine must adapt itself to physical or economic changes, a mining system must be selected in complete detail. In the past the plan chosen was usually the product of the local staff alone, however limited the training and experience of that staff might be, which often resulted in the introduction of methods that were familiar to the staff, but not so well suited to the conditions as others unknown to the local men. A new management, noting the difficulties with the existing layout, might make modifications or complete changes, so that many mines in their history have seen a whole series of mining systems, each somewhat laboriously grafted on to its predecessor. This should not be interpreted as a condemnation of the older staffs for sticking to the tried systems, such as open square-sets in the early days at the Homestake, because they knew it would work after a fashion, nor does the statement apply to the technically trained, and usually broadly experienced staffs of most present-day properties. The older miners did not have the variety of tools and methods, nor the present freedom of transfer of information as to what the other man is doing, and so did the best they could under the circumstances. Finally, the higher grade of the ores made the choice less vital. The ever-increasing need to mine low-grade orebodies, with a fixed or even lower price for the metal produced, has caused an increasing need for low-cost mining. In most new mines this has simplified the problem of selection by eliminating from consideration all of the high-cost systems, but it has also complicated the choice by the necessity for refinement in detail and a close adjustment of the plan selected to all the conditions at the property. In these low-cost problems any textbook division of mining systems as applied to "beds, veins or masses" avails little as a guide. It should be realized at the outset that to be successful under modern competitive conditions a system of mining must be worked out with elaborate detail, with careful time scheduling and control of the various elemental operations, and that after it is introduced it must be run with a large amount of technical direction.

Jan 1, 1934

By M. E. Lombardi

THE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 8 ¼ in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling.

Jan 2, 1915

By Robert Warner

WHEN a new mine is opened, and often when an operating mine must adapt itself to physical or economic changes, a mining system must be selected in complete detail. In the past the plan chosen was usually the product of the local staff alone, however limited the training and experi-ence of that staff might be, which often resulted in the introduction of methods that were familiar to the staff, but not so well suited to the con-ditions as others unknown to the local men. A new management, noting the difficulties with the existing layout, might make modifications or complete changes, so that many mines in their history have seen a whole series of mining systems, each somewhat laboriously grafted on to its predecessor. This should not be interpreted as a condemnation of the older staffs for sticking to the tried systems, such as open square-sets in the early days at the Homestake, because they knew it would work after a fashion, nor does the statement apply to the technically trained, and usually broadly experienced staffs of most present-day properties. The older miners did not have the variety of tools and methods, nor the present freedom of transfer of information as to what the other man is doing, and so did the best they could under the circumstances. Finally, the higher grade of the ores made the choice less vital. The ever-increasing need to mine low-grade orebodies, with a fixed or even lower price for the metal produced, has caused an increasing need for low-cost mining. In most new mines this has simplified the problem of selection by eliminating from consideration all of the high-cost systems, but it has also complicated the choice by the necessity for refinement in detail and a close adjustment of the plan selected to all the conditions at the property. In these low-cost problems any textbook division of mining systems as applied to "beds, veins or masses" avails little as a guide. It should be realized at the outset that to&apos; be successful under modern competitive conditions a system of mining must be worked out with elaborate detail, with careful time scheduling and control of the various elemental operations, and that after it is introduced it must be run with a large amount of technical direction.

Jan 1, 1933

By S. A. Montague

Mica can claim a considerably greater importance than would be assumed from its comparatively small dollar volume, which came to about $37,000,000 for the United States industry as a whole in 1957. Mica is one of the strategic minerals. We must depend on imports from distant sources for virtually all of our requirements of high grade block and all of our mica splittings. Mica is essential and indispensable for vacuum tubes and high-performance condensers, two electronic components which are vital military necessities besides being nearly indispensable to civilization today. Composition and Properties Mica is the general name for a group of some nine different minerals, two of which, muscovite and phlogopite, are the minerals used by the mica industry as its raw material. Several of the other varieties are commercially useful-vermiculite, * used for heat insulation in expanded form, and lepidolite, used as an ore of lithium while the others-biotite, roscoelite lepidomelane, paragonite and zinnwaldite have little or no commercial importance. Biotite frequently occurs as an undesirable impurity in muscovite. Table 1 lists various properties and other data concerning muscovite and phlogopite. Chemically, mica is a complex silicate of sodium, potassium and aluminum. Most varieties of muscovite are higher in sodium, and of phlogopite in magnesium. There are no important uses of mica where the chemical analysis is important, except that in some uses of ground mica, the content of iron oxide present as an impurity must be kept to a very low limit. Muscovite occurs in a range of color from the so-called India "ruby" which is more closely a pinkish brown, to light and dark green, with numerous other intermediate shades. Ruby color is usually preferred by industry, especially in the better qualities. When split very thin the color in most [ ] micas disappears. Muscovite mica is frequently found containing black and red "stain" as a homogeneous part of the books or sheets. In most cases this stain or impurity is magnetite

Jan 1, 1960

The scope of this paper has been restricted to the manufacture in Australia of seamless steel tubing, as the subject of buttweld tubing has already been dealt with by A. N. Hamilton in a paper delivered before the Institute in 1935.The earliest attempts to produce seamless steel tubes were based on the extrusion of lead piping, a process developed by Thomas Burr in 1820. However, the problems associated with the extrusion of white hot steel had to await the metallurgical knowledge of the twentieth century, and these early attempts were unsuccessful.The years 1840 and 1845 were noteworthy for the introduction of the first practical methods of making seamless steel tubes. In one process, a large circular plate was &apos;cupped&apos; in a vertical press; in the other, a round steel billet was pierced for its entire length.The product from both these methods was then elongated by repeated reheating and rolling over an internal mandrel, in a circular pass mill.At this juncture, it should be noted that every process developed for the manufacture of seamless steel tubing can be divided into two parts. In the first part of the process, attention is centred on the conversion of the heated bloom into a short, thick-walled, hollow cylindrical forging; this product is then elongated in the second section of the process. It will be noted that these two sections are actually quite distinct, and in practice numerous methods exist for carrying out both functions. The first stage is generally referred to as &apos;piercing&apos;, the second stage being termed &apos;elongating.&apos; In this paper, the author proposes to outline the various methods adopted for piercing and elongating; the reader is asked to note that although certain methods of piercing are almost invariably associated with only one method of elongating, the distinction between the two functions is, nevertheless, a vital one and should be noted accordingly.

Jan 1, 1947

By D. Harrington

"The recent discovery and exploitation of petroleum territory have resulted in the enactment of new petroleum laws in most of the South American Republics. The activities in the discovery of these new fields were engendered by the knowledge of the fact that present producing fields must within well defined periods be exhausted. Oil operators were willing to take the initial steps in exploitation in the absence of legislation that applied strictly to petroleum operations. The enactment of modern legislation in many of these Republics encouraging and protecting exploitations may cause tremendous oil activities in these countries, and the results may be comparable with the magnitude of the undertakings and the prestige of the companies now entering this territory.These, oil fields are admirably located for convenient distribution of petroleum by water to all the Nations using oil as fuel for shipping and industrial concerns. The oil markets of the western coast of South America will derive immense benefits from the Panama Canal. This navigation route brings these markets into direct ocean shipment with the Atlantic coasts of the Western and Eastern Hemispheres.One deterrent to oil production in the Republics of South America is the want of inland. transportation facilities, but the recent laws of these Republics without exception provide for acquiring rights of way for pipe lines and other modes of transportation; and doubtless the great interests and. syndicates already operating in these regions will, as production increases, provide ample pipe line transportation sufficient to convey to the coast the oil produced. It way be assumed, from the legal guarantees afforded, and from operating equipment and machinery that are now being concentrated that refineries will be erected at shipping points for the purpose of making these petroleum products accessible to the world."

Jun 1, 1921

By S. Shimaya, T. Maejima, M. Shimo

"The authors conducted the in-situ gas-tightness tests in a fractured rock at the Namikata underground LPG storage site in Ehime prefecture, Japan. The test consisted of two independent setups, a gas-tightness test that used boreholes, and a chamber-scale test that used a horizontal drift sealed with a concrete plug. In each test, the gas pressure was increased up to the onset of the measurable gas flow to obtain the maximum containment pressure. This paper discusses the hydraulic conditions for gas leakage initiation and the importance of the pore pressure measurement for monitoring the gas-tightness of the LPG storage cavern based on the test results.INTRODUCTIONJapanese first underground LPG storage plant was constructed by JOGMEC, the Japan Oil, Gas and Metals National Corporation, at Namikata in Ehime prefecture in granitic rocks (Kato et al., 2007). The “hydraulic sealing principle” (Åberg, 1977) that utilizes groundwater flow into an unlined cavern to prevent the leakage of gas through fractures in the surrounding rock mass was employed for storage of LPG. This paper describes the results of the in-situ tests performed at the Namikata Site to obtain information on fundamental gas-tightness characteristics of fractured rock. Two types of in-situ tests, a borehole gas-tightness test and a chamber gas-tightness test, were carried out near the storage caverns. Figure 1 shows the cavern layout of the Namikata underground storage plant and the test locations. The storage facilities consist of three caverns (W26m×H30m×L485m). The cavern crown lies at a depth of 150m below the sea level in Cretaceous granitic rock (Figure 1). Water curtain boreholes excavated from the water gallery tunnel at EL-125m level are located above and side of the caverns to prevent water drainage from fractures during the construction stage as well as during operation. The borehole tests were performed from a drilling adit excavated from the eastern end water gallery tunnel, while the chamber test was conducted at the southern edge of an exploratory drift extending from the central water gallery tunnel."

Jan 1, 2015

By C. Pelley, A. Piche

"The Canadian mining industry faces the prospects of a severe shortage of graduate mining engineers over the next decade. This arises from three factors: first, a growth in industrial activity; second, the average age of company engineering and management staff; and third, the reduced number of students in engineering faculties around the world. This paper aims to identify the critical factors underlying the trend of inadequate recruitment into higher education for mining and to examine means of alleviating the problem.This paper is based upon surveys of potential and current students and graduate mining engineers from four mining schools. An attempt is made to understand institutional and industrial images, career prospects and what is required to attract enough high-calibre young people into mining education over the next decade.IntroductionThe mining industry has started to experience a severe shortage of graduate mining engineers which is likely to persist and even worsen in the short- to medium-term.This arise s from three principal factors:1. a recent and strong growth in mining activity, which surpasses that experienced through the 70s, before the recent international industrial recession; .2. an increasingly older average age of mine engineering employees, at least in the industry&apos;s larger companies; and3. problems associated with maintaining adequate mining undergraduate recruitment levels ."

Jan 1, 1989

By H. H. Keller, E. J. Couch

Damage to production wells subjected to the high temperatures associated with in-situ combustion projects has been a problem since the advent of this thermal recovery technique. Injection of water down the annulus of hot wells has been successfully utilized for cooling and prolonging the life of such wells. A mathematical model that is suitable for predicting the effectiveness of cooling water in a particular application is developed. Typical results for practical ranges of the various parameters involved are presented. INTRODUCTION In the normal course of in-situ combustion operations, highly damaging conditions develop in the production wells as the combustion zone approaches, and these wells are subjected to high temperatures (up to 1500F). The resulting well damage is recognized as one of the more serious operating problems unique to the in-situ combustion process. Even in operations where well completions have been specifically designed to cope with this problem, the question arises as to how this destructively high temperature can be kept within tolerable limits. A simple and economical approach to this problem is to circulate cooling water down-hole. This method has been used with some success in shallow reservoirs. At greater depths, however, the heat exchange with the overburden surrounding the well and between the fluids in the tubing and the annulus tends to equalize the temperatures of the two fluid streams so that the cooling capacity delivered to the bottom of the hole decreases with well depth. This method would provide no appreciable control over the bottom-hole temperature at great depths. In order to delimit the condition under which cooling by water circulation is effective, the wellbore temperature must be related to the water inlet rate and temperature; to the reservoir depth, production rate, and initial temperature; and to the combustion at at bot tom-hole depth. A model that meets these requirements and that will offer an approach for developing engineering solutions to practical design and operating problems is described in this paper. MATHEMATICAL MODEL Previous studies of temperature distributions include those for flowing wells1p2 and those for hot fluid injection. Adams and Haddenhorst 6 presented solutions for the down-hole circulation of hot oil in the treatment of paraffin-deposition problems. In this paper the thermal model presented by Ramey 4 is adapted to the flow system shown schematically in Fig. 1. Water at temperature Ti is injected at a rate wi and flows down the annulus outside the tubing. It mixes at bottom-hole depth D with the fluids produced at race w from the hot reservoir at temperature T. This mlxtureJ. of injected water and reservoir fluids flows up the tubing and is produced at the surface at TI,. In order to describe the temperature response in this system, we make use of the usual conservation of

Jan 1, 1969

By Harry L. Brown, Philip E. Armstrong

Young&apos;s modulus doto ore presented for W, Mo. Ta. V, Cr. Ni, Ti, and Zr as a function of temperature up to about 0.7 of the melting points. A plot of reduced temperature us reduced modulus produces a general correlation except for titanium and zirconium. Young&apos;s modudlus data for some representatiue commercial graphites are given up to 2400°C. All results were obtained from longitudinal resonance-frequency measzrrements of 4-in. long samples, corrected for simultaneously measured thermal expansion. Comparison of poly crystalline and single-crystal tungsten behavior indicates that all the observed modulus values are frequencv -dependent at the higher temperatures. STATIC measurements of elastic properties of materials at elevated temperatures are extremely difficult to make since the elastic behavior is obscured by relatively large first-stage creep effects. Dynamic methods which avoid this difficulty by utilizing the measurement of the resonance frequency of a simple vibrational mode have been described in the 1iterature.l-3 The authors have extended the operating temperature range of this type of measurement to above 2000°C and have described the equipment elsewhere.~ The Young&apos;s modulus data presented here were obtained with this equipment, using samples about 4 in. long and 1/4 in. diam, supported horizontally at the center and excited to the fundamental longitudinal resonance frequency. Young&apos;s modulus was calculated by the formula: E = 4f2f2p where E = Young&apos;s modulus, / = frequency, 1 = length, and p = density. Dilatometric data were obtained simultaneously by optical measurements of the change of length of the sample. For the metals tested, an attempt was made to obtain modulus values that would be representative of the pure, strain-free, randomly oriented material. All of the graphites studied exhibited a high degree of elastic anisotropy, while the method assumes an isotropic homogeneous material. However , when the values for Young&apos;s modulus obtained for AUC graphite were compared with those taken from static measurements at room temperature they were found to be only about 4 pet higher. This is excellent agreement considering the low precision of modulus calculations from stress-strain curves. The difficulty in using data of apparent Young&apos;s modulus for anisotropic materials arises when the attempt is made to use these data and shear-modulus data to obtain Poisson&apos;s ratio. The results are usually meaningless and sometimes absurd.&apos; RESULTS Table I lists the sources, impurity content, thermal history, and dilatometric constants of the metal samples that were investigated. All the metal samples were tested under a vacuum of 1 to 5 x 10-5 Torr. Where our dilatometric data agreed with previously published data, the table lists the previous values and the literature reference. Where no reference is given, the constants were determined from our dilatometric data. Table II presents the modulus data in units of millions of psi as a function of temperature in degrees centigrade. The numbers were obtained from curves fitted to the experimental data. For some types of calculations, such as those attempting to correlate creep data, the slope of the modulus curve is of interest, and this information also is reported in Table 11. It is always tempting to try to fit physical-property data into some general pattern and then use this pattern to predict the behavior of other similar materials. The general pattern for an elastic modulus of a metal seems to be a linear deoro- with increasing temperature Over the range between 0.1 and 0.4 of the melting temperature, then a progressive1y decreasing value up to the melting point. Metals appear to retain finite moduli

Jan 1, 1964

By L. Michael Kaas

Any increasing number of restrictions are being placed on mining management&apos;s ability to pursue profit. Raw materials pricing, the cost of capital equipment, labor cost, and overhead costs, are becoming more difficult to control. Cost reduction is one of the few remaining areas in which management may still exercise its profit making ability. Equipment maintenance is an area where mine and mill management can readily reduce costs and increase profits. Why is this possible? First, maintenance costs comprise a large portion of total operating cost. Thirty to sixty percent of the operating cost dollar is not unusual. Even a relatively small percentage reduction in this cost represents a very sizeable increase to mining profitability.

Jan 1, 1967

By A. Koursaris, J. B. See

An investigation is described in which the resistivities of Mamatwan manganese ore, Delmas coal, and Iscor coke, at temperatures or up to 1400°C were determined, as well as the resistivities of mixtures of ore of a constant size range with Delmas coal or Iscor coke of three different size ranges. The resistivities of the ore and the coal were characteristic of those for semi-conducting materials, were strongly influenced by temperature, and decreased by several orders of magnitude between room temperature and IOOO°C. The resistivity of the coke changed only slightly between room temperature and 1400°C, and the resistivity of the coal approached that of the coke at I300°C. This provides support for the theory that the resistivity of carbonaceous reducing agents is primarily a function of heat treatment, and not of the rank and composition of the coal. Above 1200°C, the resistivity of mixtures of ore and coke fell steeply owing to an increase in the volume fraction of coke in the mixture and to the formation of slag. The results were similar for the three different size ranges of coke. The extremely high resistivities of ore-coke and ore-coal mixtures at Iow temperatures indicate that there is unlikely to be much conduction of current in the higher regions of a furnace. Thus, the resistance of a furnace is governed mainly by the conditions at the electrode tips and in the molten regions. To explain the very Iow resistances of furnaces, usually, about I m£?, it would be necessary for investigations to be conducted under conditions similar to those in the active zone of a furnace.

Jan 1, 1980

By Alan A. Campoli

The U.S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By R. W. Kewish

The preparation of massive uranium metal containing very low concentrations of a number of light elements by bomb reduction of UF4, with calcium is described. Details of procedures are given for preparing high-purity ingredients for the bomb reduction. The as-reduced uranium metal contained, on the average, less than the following amounts of light element impurities, in ppm: Li, 0.1; Be, 0.1; B, 0.1; C, 25; 0, 70; Na, 1; Mg, 3; Al, 2; and Si, 7. Other impurities for which the metal was examined averaged, in ppm: Ca, < 10; V, < 10; Cr, 2; Mn, 6; Fe, 50; Co, < 5; Ni, 8; and Cu, 1. THE preparation of very high-purity uranium metal in massive form for research purposes is of great importance. Recently the kilogram-scale preparation of uranium metal containing less than 70 ppm of detected impurities was accomplished by Blumen-thal and coworkers by vacuum remelting of high-purity crystals of uranium obtained by fused salt electrolysis.1"3 Albert and coworkers4 have reported successful experiments in lowering the concentrations of certain impurity elements in uranium, notably iron, to a few ppm by the zone-melting method. The present paper describes the preparation of high-purity massive uranium metal by the bomb reduction of UF4, with calcium. Early in 1951 a program was undertaken at the Los Alamos Scientific Laboratory to prepare uranium metal of very high purity with respect to a number of the light elements. The methods considered for this purpose were 1) bomb reduction of a uranium halide with calcium, 2) electrolysis of fused salts, and 3) hot wire decomposition of UI4, The first of these processes had been used extensively at Los Alamos since 1943 (and still is used) for the production of uranium metal.5 In considering the three processes it was evident that either of the last two would require an extensive development program with no certainty of success. On the other hand, a study of available data showed that uranium metal of very high purity with respect to some light elements had occasionally been made in routine processing by the first method. It was therefore decided that an intensive study of the bomb-reduction process would be made to see if it could be improved to yield uranium metal with very low concentrations of light elements. DEVELOPMENT OF PROCEDURES The bomb-reduction process used at Los Alamos consists of reducing UF4 with calcium, using iodine as a booster. The reaction is carried out in a magnesium-oxide crucible enclosed in a steel bomb. Argon is used in the bomb to avoid objectionable side reactions which would occur in the presence of air. All ingredients for this bomb-reduction process were examined as possible sources of light elements. It was known that high-purity UF4 was required. The calcium used in the reductions was a source of carbon and magnesium. The magnesium-oxide crucibles were sources of boron, silicon, and magnesium. The iodine did not appear to be a source of any impurities. Pure UF4- The UF4 for bomb reduction is prepared from U3O3 , by successive reduction to UO2, with hydrogen and hydrofluorination of the UO2, with anhydrous HF. Since it was known that no impurities were normally introduced during the gas-solid reactions, effort was directed toward the preparation of high-purity U3O3. Of the many possible procedures for the purification of uranium solutions the following were investigated: 1) Precipitation of uranium peroxide. (Two procedures were tried. The first consisted of simultaneously adding hydrogen-peroxide and ammonium-hydroxide solutions to a uranyl-nitrate solution, containing citric and malonic acids, at such relative rates that precipitation was carried out at a constant pH of 1.5 The second consisted of simultaneously adding uranyl-nitrate, ammonium-hydroxide, and hydrogen-peroxide solutions to an aqueous solution

Jan 1, 1960