Search Documents

By H. Huang, R. N. Gow

"The reactivity of an enargite mineral electrode was investigated spectroelectrochemically under conditions typically found in alkaline sulfide leach solutions, with pH 11-13 and Na2S additions of 50 and 250 gL-1. A bulk enargite electrode was cycled between 0 and -1,000 mV for each set of solution conditions. Raman spectroscopy was used to determine and compare surface formations against species in mass-balanced EH-pH diagrams generated using STABCAL. Previously, it was determined that arsenic could be selectively leached under alkaline conditions at an average solution potential of -300mV, across the pH range 11-13. Operating under such conditions allowed for the selective leaching of arsenic with elemental sulfur formation. From several of the voltammograms obtained during this current testing, the formation of elemental sulfur appeared at increasingly reducing conditions with increasing sulfide concentration. At high concentrations, copper started to dissolve, possibly as a bisulfide complex, reducing the selectivity of the leach, unlike previous studies. However, the presence of the higher sulfide concentration is also anticipated to prevent passivation by consuming any surface formation of elemental sulfur. This study provides insight into the operating parameters of alkaline sulfide leaching in regards to the selectivity of arsenic leaching, as well as guidance for control of reagents and solution potential and, of course, the need for water treatment afterwards.IntroductionEnvironmental limitations on the pyrometallurgical processing of arsenic-bearing concentrates have forced operations to consider other solutions. Attempts to hydrometallurgically process enargite (Cu3AsS4) fall into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under basic conditions. The authors believe that the selective leaching of arsenic is more amenable because it produces a solid copper phase, preferably chalcocite (Cu2S) or covellite (CuS) that could then be processed using conventional methods already in place in the copper and gold industries. Potential leaching methods include alkaline sulfide leaching (Achimovicovica et al., 1999; Anderson and Twidwell, 2008a,b; Tongamp et al., 2009 and 2010), hypochlorite leaching (Vinals et al., 2003; Curreli et al., 2005; Mihaljovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and acid leaching (Gow et al., 2014b) with or without fine grinding to mechanically activate the enargite surface and increase normally slow leach reaction kinetics (Achimovicova et al., 1999; Balaz et al., 2000; Balaz and Achimovicova, 2006). In this study, the reactivity of enargite under alkaline sulfide leach conditions was examined."

Jan 1, 2015

By J. R. Long, E. T. Hayes, D. C. Root, R. S. Dean

The U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities1 and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriatc applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately- applicable. While atomic: hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-are methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1947

By J. R. Long, R. S. Dean, D. C. Root, E. T. Hayes

The U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities1 and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriatc applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately- applicable. While atomic: hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-are methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1947

By John Wulff, Richard P. Seelig

THE importance of the pressing operation in the forming of articles by powder metallurgy depends to a great extent on the type of product to be made. While in some few cases the pressing is merely a means of compacting loose powder particles into a solid mass preliminary to a sintering treatment in most applications it constitutes a molding operation with the purpose of shaping the raw material in powder form into a certain predetermined, accurately defined part not altered in shape by sub- sequent sintering. In still other cases, no pressing at all but sintering in molds gives useful articles. A limited number of products are made by the simultaneous application of pressure and heat. The factors that control the product of the pressing operation are raw material, lubricant, type, size and shape of die and compact, magnitude and time of application of pressure, as well as temperature of pressing. All such factors need to be con- trolled; yet, depending on the function of the pressing operation, greater emphasis may be placed on processing factors other than the pressing operation. In any complete discussion of pressing, subsequent sintering cannot be disregarded. For the sake of brevity, the present paper has been limited to the mechanics of pressing and only occasionally refers to sintering. For the same reason, hot-pressing has been omitted as beyond the scope of this paper. In any survey of the literature on the pressing of metal powders, the 1938 paper of Balshin1 on the theory of the process of pressing deserves mention. The first attempts at an interpretation of pressing phenomena were made by Balshin1 and Rakovski.2 The experimental results of both are of great interest. Since the experimental results are not described, the work was repeated, using our own interpretation of the possible techniques, and is reported in the following pages. The basic theory of Balshin,1 based on a hydro- dynamic analogy, however, leads to but another way of plotting density and pres- sure against height of a pressed compact. Since it does not give any new insight into the phenomena, nor account for the influence of side-wall friction, a discussion of the theory has been omitted from this paper. DENSITY GRADIENTS IN COMPACTS The process of pressing metal powders in a die (disregarding for this consideration the powder filling and ejection operations) may be divided into three phases: (I) packing, (2) elastic and plastic deformation, (3) cold-working with or without fragmentation. It must be emphasized that these three steps do not follow each other in sequence; on the contrary, in practice

Jan 1, 1946

By E. E. Thurlow

The Geology Div. of Northern Pacific Railway Co. has adapted to its exploration efforts field procedures for geochemical sampling and semi-quantitative analysis which have been developed through research by the U. S. Geological Survey. The sampling is done in conjunction with reconnaissance geologic mapping on aerial photographs or during field checking of maps which have been prepared largely by photo-geologic interpretation. Stream sediment or soil samples are taken and readily soluble combined heavy metals are extracted with ammonium citrate followed by colorimetric titration with dithizone at the sample site. The effectiveness of this approach has been demonstrated both in positive and negative results, thereby assisting in the elimination of large areas of land from further immediate attention and in providing targets for followup exploration. An occa sional sample is submitted for spectrographic analysis as a check on the possible presence of other elements of economic significance. Field laboratory procedures are also being implemented for determining molybdenum, mercury, and other metals which may be valuable in themselves or useful as pathfinder elements in outlining mineralized areas. A lead-zinc occurrence in Oregon and a copper deposit in Montana were readily detected and outlined by stream sediment and soil sampling and a heavy metal anomaly that lacks obvious interpretation has been found in northwestern Montana. Detailed mapping and additional sampling are followed by other exploration techniques if warranted. Northern Pacific's program of reconnaissance mineral evaluation of company-owned lands and adjoining areas was outlined in a paper presented at the American Mining Congress meeting in Las Vegas four years ago. That report included policies and procedures with respect to mineral development on Railway Co. lands and may be referred to for information on these matters.1 In a sense this paper is a progress report on the use of geochemical prospecting in Northern Pacific's continuing mineral evaluation program. At this time there are positive results but as yet there is no real success story in the form of a minable ore body. GEOCHEMICAL PROSPECTING PROCEDURES The decision to use geochemistry as a reconnaissance exploration tool must be followed by research into sampling and analytical methods and into the interpretation of results. Various analytical methods were tried and evaluated by the Geology Div., including hot and cold acid extraction with and without fusion of the sample, panning and magnetic separation followed by dithizone testing of the magnetite, and cold aqueous extraction of metallic ions followed by indicator tests. Samples were first sent to the laboratory for analysis; later field laboratories were established and now virtually all testing is done at the sample site. It was concluded that, where applicable, the quickest dependable methods for reconnaissance use are the dithizone field tests for readily extractable heavy metals. This involves the simultaneous treatment of a sample, usually of soil or stream sediment, with two immiscible liquids; one a cold aqueous extractant (ammonium citrate) and the other a solution of dithizone in toluene or xylene.2 Dithizone is a colorimetric indicator that reacts quantitatively with copper, lead, zinc, and several other metals to form colored complexes in organic solvents. Results may be expressed in ml of 0.001 pct dithizone that are required to reach the blue end point, or calibration of the test results can be carried out with standard solutions of zinc; conversion factors would then be expressed in ppm, zinc equivalent. Calibration of dithizone solution with zinc standards indicates that 1 ml of 0.001 pct dithizone is equivalent to approximately 0.25 ppm of zinc. An authoritative report on dithizone field tests authored by H. E. Hawkes in the June-July 1963 issue of Economic Geology* states "The appeal of these techniques has been the simplicity and speed of the determinations as compared with more tedious laboratory determinations of trace metals in weathered rocks, soils, or plant materials. This obvious appeal, however, has often been more than matched by misuse of the method in such a manner that the results are

Jan 1, 1964

By Michael Rieber

Commodity transportation by barge is possible on about 25,000 miles of navigable inland waterways in the contiguous 48 states. Barge operations are used chiefly for the movement of bulk raw materials ranging from farm products to iron ore, coal, and other bulky semi-finished as well as finished products such as steel, chemicals and petroleum [3,p.7-9]. The barge industry, unlike other transportation industries, is largely unregulated. This is because all liquid bulk commodities most dry bulk commodities transported by for-hire carriers and companies engaged in private transportation of their own commodities are exempted from Interstate Commerce Commission regulations. As a result, about 15 percent of the total ton-miles of barge traffic each year is under Interstate Commerce Commission regulation [13,p.14-25].

Jan 1, 1977

By R. D. Carnahan, J. E. White

A study of dispersion strengthening in TD-Nickel (nickel plus 2 vol pct Tho2) was conducted employing microstrain techniques at ambient room temperature. It was found that optimum strength was due primarily to the incorporation of stored energy developed by a variety of thermal-mechanical treatments. The relatively low strength of the recrys-tallized condition implies that the dispersed particles themselves offer only token resistance to deformation. The development of resistance to large-scale recovery or recrystallization at temperatures near the melting point requires a more extensive sequence of strain-anneal cycles than does the development of optimum strength. A micro-Bauschinger effect was observed which appears to be related to the lattice resistance to the movement of free dislocations. The effect was nearly identical to that in pure nickel indicating that the presence of the dispersed phase and considerably increased dislocation density (stored energy) only alters the number or effectiveness of barriers. THE early stages of deformation of engineering materials can be conveniently studied by utilizing strain-gage techniques which permit resolution of strains less than 5 X 10-7 in. per in. for testing in four-point bending (Carnahan and white1). The present investigation, part of a continuing study on the very early stages of deformation, was designed to reveal the true role of a dispersed phase in promoting high strength in a commercially available dispersion-strengthened alloy. Although this technique has been used for some time to study microdeformation in pure metals and alloys, it has just recently received attention as a means of investigating dispersion strengthening. Studying the very early stages of deformation in alloys which depend upon a finely dispersed inert phase for strength may prove to be a very important method for a better understanding of these materials. It is essential to obtain considerable clarification of actual dislocation movement and the kinds of deformation barriers which exist before optimum properties can be designed into this type of material with any degree of confidence. Considerable research on a variety of dispersion-strengthened materials has resulted in two different schools of thought regarding the strengthening mechanism. One faction2-4 favors the idea that the particles themselves resist the motion of dislocations. The criterion for yielding is the fracture of the dispersed second-phase particles due to an array of piled-up dislocations. Other invesfigators5-a have shown that particles are effective primarily by allowing a greater buildup of stored energy or dislocation density through thermal-mechanical treatments in the composite than the pure matrix material. The particles themselves, then, are not exclusive obstacles, but the complex network of particles, dislocation tangles, subboundaries, and grain boundaries are strength determining. The development of such a complex dislocation network in SAP has been studied recently in some detail by Goodrich and Ansell. The ability of dispersion-strengthened alloys to resist softening or recrystallization is also of considerable importance; however, the criteria for maximum stability may not necessarily be those for maximum strength. In this study, in addition to the evaluation of the microstrain properties of TD-Nickel, it is felt that considerable clarification of the true dependence of strength and stability on the dispersed phase is shown. I) MATERIAL AND PROCEDURE TD-Nickel is a dispersion-strengthened alloy developed by the E. I. DuPont de Nemours Co., which contains 2 vol pct thoria (Tho2) in a pure-nickel matrix. The average ThO2 particle size is approximately 0.1 p and the interparticle spacing is less than 1 u. The material was supplied by DuPont in two conditions: hot-extruded bar stock, and stress-relieved cold-rolled sheet 0.025 in. in thickness. The bar was extruded at 2200°F from a cold-pressed and sintered billet. The sheet stock was prepared from the extruded material by a process involving ten or more 50-pct cold reductions by rolling with intermediate anneals at 1800° to 2000°F. Test specimens used in this study were prepared in the form of rectangular parallelepipeds measuring 0.375 by 1.375 in. in thicknesses ranging from 0.025 to 0.040 in. Samples prepared from sheet and extruded stock were mechanically polished before heat treatment and were handled with extreme

Jan 1, 1964

By Otto F. Pfordte

The great advance of the last twenty years in the specialization, delicacy and efficiency of ore-concentrating apparatus calls for a finer system of testing both the qualities of ores and the operations of machines in this department. In amalgamation, lixiviation and smelting, the daily employment of physical and chemical tests has been recognized as necessary, and the cost of the necessary laboratories and employees is cheerfully paid. But while much progress has been made in concentration (due, in a large degree, to the study of the subject in our technical schools), it is still too common in actual practice to follow the loose old method of roughly estimating, once for all, that a given ore " concentrates x tons into one," and resting on this assumption so long as that ore continues to be treated, while assays of the tailings from concentration are made from time to time, without exact determination of their quantity. The first step toward accuracy of control must be a more frequent and precise measurement of the quantity of concentrates from a given operation. This should be expressed in pounds per unit of one ton; and the variations shown in frequent determinations will furnish a constant check upon the character of the ore and the performance of the apparatus. But this is only a part of what should be constantly and systematically done to insure the best work upon a material which must vary continually, even though it come from one mine only. If, in any mill, appropriate laboratory-tests were made at least once a week, the labor and expense involved would be amply repaid by increased knowledge and control of the current operations. A small testing-laboratory, provided with a few gold-pans;

Jan 1, 1902

By Russell Frith

Probably the most expensive but least well understood roof falls in underground coal mining, are those that occur ahead of the powered supports in the centre of longwall face. Even small roof cavities result in the dilution of the ROM product and large cavities can stop the face for days if not weeks and the incurred cash flow losses can be catastrophic. Expensive and time-consuming remedial measures (e.g. PUR, cavity filling, removal of stone from the AFC by hand) are required and equipment wear and damage can be significant when the need to blast and convey stone is also considered. Through four major research projects within the Australian coal industry and numerous consulting assignments, the author has spent the best part of fifteen years attempting to identify and defme the various geotechnical and operational factors that determine whether a major roof cavity occurs ahead of the powered supports or a normal goaf fall occurs just behind them, the difference in operational outcome being enormous. The paper presents a condensed summary of the overall technical findings covering such issues as roof fall mechanisms, the measured influence of cover depth, periodic weighting of massive strata units and its quantification, the role of cut-throughs in chain pillars, face width and height, the role of the powered support and the influence (both positive and negative) of mine site operations. The big picture outcome is the view that high production longwall extraction is well-suited to certain geotechnical environments, is marginal in others and under certain conditions is fatally flawed and beyond the control of mine operators, although fortunately the latter category is a relatively rare situation. Various risk-based research findings in this regard will be given as a basis for future discussion.

Jan 1, 2005

By Remmerswaal, U. Boin, M. B. G. Castro

"To design sustainable products that can be recycled with high resource efficiency, low environmental impact and economic feasibility, the choice of materials and materials combinations, made in the design stage, is fundamental. The products we design, manufacture and use now will be the resources of the future. Designers are able to select materials for a product according to the many functional requirements they must fulfil. But they have a limited knowledge of the recycling processes and its requirements regarding quality of the secondary material streams. Resource Engineers have to manage the processing of these streams, that are becoming more complex with the increasing variety of materials and decreasing size of components. After mechanical separation of the materials streams resulting from shredding of EOL (endof- life) products, there is always a degree of contamination, from two possible causes:Incomplete liberation: the bonds between different materials combined in a component are not completely destroyed by shredding, resulting in some particles containing two or more materials attached;Separation efficiency: the mechanical separation processes are not able to separate perfectly the many material particles; there are always a number of foreign particles in the recovered streams.Sometimes, those contaminants cannot be removed by the industrial metallurgic recycling processes, and a more serious problem occurs when the contamination levels compromise the recycling of the material stream by lowering its quality (i.e. the properties of the recycled material will be lower due to the contamination). As a consequence, the material must be diluted in virgin raw material and/or used in a less demanding application (downgrading), causing resource depletion and increased energy use, waste production and recycling costs. In order to make the best choice of materials combinations for a product, a systematic approach is necessary, that can close the gap between the knowledge areas of Product Design and Recycling Technology."

Jan 1, 2003

By Roberto Fernandez

Want of knowledge on the part of experts from abroad respecting the amalgamation-system, known as the Mexican or patio process, has been the cause in this country of trouble to many foreign mining companies. This process has not been looked upon by their managers as a satisfactory method of treating silver-ores, and they prefer to employ others, which, although more modern, and often more profitable in other countries, have not proved to be so under the exceptional conditions of this country, where labor is cheap and paid in silver, while fuel is very dear. The cause of this error of judgment is probably the inexact information which has been furnished by several authors respecting the economical results of the patio process. This treatment is not suitable for silver-ores of every kind. Simple sulphides of silver are best adapted to it, and, next to these, the combinations of complex sulphides, viz., pyrargyrite, polybasite, stephanite, proustite, etc. Chlorides, bromides and iodides of silver are considered rebellious ; argentiferous galena, blende, bournonite, as also argentiferous arsenical pyrites of iron and copper, are absolutelg unsuited to this treatment. Experience has proved that high-grade ores do not give as satisfactory results as those of mediurn grades, as, for instance, carrying from 1 to 2 kilos of silver per metrical ton. The patio process, as actually practiced in this district, comprises the following operations: 1. The ore is crushed in a dry state in a roller-mill, reducing it to pea-size, from which uniform samples, and, in consequence, correct assays, can be obtained. 2. It is then thrown into the arrastra, and pulverized with water, so fine that it will pass through an 80-mesh screen.

Jan 1, 1900

W. L. Saunders, New York, N. Y. (communication to the Secretary*):—The Laramie tunnel, though a small one, compares very favorably in the speed of driving with the great Alpine tunnels which have the record so far. I think it safe to say that, taking all things into consideration, the record made at Laramie is the best American record, though it still falls short of the long-tunnel records abroad. In discussing tunnel-records it must always be borne in mind that there are conditions peculiar to each individual tunnel job, so that no comparisons are complete, fair and conclusive. At Laramie there is one point which stands out prominently, and which distinguishes this from any of the recently-built Alpine tunnels, and that is that here we have great progress in an American driven tunnel without the use of a carriage for mounting the drills. At the Arlberg and Loetschberg tunnels, the carriage was an essential condition for progress. All the heading-drills were mounted upon a bar which rested upon a small carriage. This carriage was withdrawn after the drilling and run into the heading after the blast without much disturbance of the drills, and with very little adjustment except that required in jacking the horizontal bar across the tunnel. The carriage was so small in its track-area that it required little mucking to run it in to the face; and as the rock-drills used were heavy machines 38 in. in diameter, progress in setting up and drilling was very much accelerated by the use of the carriage. At the Laramie tunnel hammer-drills were used instead of piston-drills, and here we have an important distinction which

Jan 1, 1913

By David R. Mitchell, Byron M. Bird

THE revision of this chapter has presented a problem in that heavy-medium jigging has come into the picture since the chapter was originally written (seven years ago), a practice in which an artificial medium is built up and maintained in the jig circuit. As this development makes the jig a "true" heavy-medium process, the method belongs in the chapter dealing with such processes. Although putting this development in its proper position in the book involves some repetition, this seems to be the best procedure, and it has been followed. As the chapter on jigs in its original form was intended to be more or less a handbook on jigging for the use of the practical man, and the great bulk of the material therein is still generally applicable, the text has been re-used in large measure. Two major changes should be noted: (1) the portion of the text relating to the refuse-withdrawing mechanism of the McNally-Pittsburg jig has been entirely rewritten, and (2) a description of the hutch valves on the Jeffrey jigs has been added. Jigging is the stratification of a mass of solid particles in upward and downward pulsations. The stratification usually is effected in a rectangular open-top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (2) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through 3/4-in. to 0, and mixed sizes of ores down to 7/32-in. to 0and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 per cent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems.

Jan 1, 1950

By Charles Baskerville

SHALES containing,"kerogen,," or bituminous matter, which on destructive distillation yield oily and tarry matters resembling petroleum are here designated as oil-shales. They differ from oil-bearing shales from which petroleum may be obtained by so-called mechanical means. The educts obtained by the destructive distillation resemble some or all the varieties of petroleum, depending on the character of the shale and the mode of treatment. Some shale oils have e a paraffin base, some an asphaltic base, or a combination; some run high in sulfur compounds, The methods of refining and cracking, therefore, are essentially the Sam as are used in refining petroleums. In 1860, in this country, over fifty companies were successfully distilling various bituminous natural materials for the production of "coal oil," used for illuminating purposes. The discovery of petroleum and the failure of these companies to save and utilize the valuable byproduct, ammonia, brought about their inevitable doom. Prior to that time, more or less successful efforts were made to produce from the shales of Scotland oils for illuminating and heating purposes. Competition of native petroleum from the United States early eliminated some of these companies and with the entrance of oil from the Russian and other fields into the world's markets, the Scottish oil-shale industry underwent serious and trying experiences until, in 1916, only four (Scottish) were paying concerns.. These survived only through energy and the application of skill in saving valuable byproducts. A few companies have successfully operated in France and New Zealand. The Canadian Government showed active interest in the New Brunswick shales, which exist in quantity and are more valuable than the Scottish shales. The retarded development of that very valuable asset of the Province of New Brunswick involves a pathetic history, which is lamentable. This was especially true when the product was so much needed in the prosecution of the war. The economic success of a shale-oil industry depends on the following factors:

Jan 6, 1919

BECAUSE you cannot always proceed by the ordinary pathway since you sometimes find yourself in a place where you cannot have all that you might need or wish, it often happens that it is necessary to know how to recognize and understand your materials well, in addition to having them well disposed, and to know how to use your, ingenuity in arranging a mould., Furthermore, things have a great diversity among themselves, and it is not possible to give a particular rule for all. But if you have a certain broad fundamental knowledge when you have need of many things, the ingenuity awakens and supplies its needs by imitation. Now, because I have thought that you had not hitherto had the slightest shadow of knowledge of what I have described in this treatise of mine, I have expanded and narrated things in greater detail than perhaps I might have done. For this reason I have also decided that I wish to tell you of several methods that can be used if you wish to mould, especially in making an intaglio* for a relief, t or in making another intaglio in bronze from either an intaglio or a relief. And I will tell how every relief reduces, itself from convex to concave and also how the relief is made from the intaglio. These works are first made of plaster or pastes or some other liquid thing that is soft when moulded and becomes hard either by drying out with heat or by shrinking with cold, such as tragacanth, plaster of Paris, sulphur, lead, wax, or similar things. And, in conclusion, we describe the method of making an intaglio from a solid. In making an intaglio you must first consider whether it is a large or small thing, figure or foliage, whether it is in demi- or bas-relief, and whether it is a thing that projects from the mould wholly or in part.

Jan 1, 1942

By Yong-neng Feng, Xiao-ping Chen, Wei Guo

"While the uniaxial compressive strength of rock has been extensively investigated, the relation between the saturation and natural compressive strength is relatively unexplored. This paper studies on 1865 statistical data of Chongqing Rail Transit Line 1 and Line 6, which located in the Middle Jurassic of Shaximiao formation. The research focuses on the relation between the saturation and natural compressive strength. The statistical data are categorized and quantified in order to ascertain the softening properties of sandstone and sandy mudstone. The findings suggest that the saturation compressive strength is significant effected by its natural compressive strength, and an empirical formula is introduced to explain the relation. These findings have implications for researchers and engineer who concerned with Chongqing rail transit construction.INTRODUCTIONIn the engineering construction and surrounding rock classification, the uniaxial compressive strength index (Ministry of Water Conservancy, 1995; Ministry of Railways, 1999) is one of the essential parameters of rock mass. Usually, there are two types of the uniaxial compressive strength index, natural and saturation compressive strength, and the ratio of them is the softening coefficient. Most of the previous studies on rock strength had focused on the influence factors (Liu et al., 2008; Liu et al., 1998; Liu et al., 2013; Wang, 2013; Zhang et al., 2008; Zhang et al., 2010; Zeng & Lin, 2003) with experiment and in-situ tests. But few publications that reports a long and formal research project on the relationship between natural and saturation compressive strength. In order to figure out this issue, this study investigated the distribution of Solidity Classification of Rock Mass and softening coefficient based on the statistical data of Chongqing Rail Transit Line 1 and Line 6. Based on the analysis, an empirical formula was proposed to explain the relationship."

Jan 1, 2015

By W. R. Shimer, F. O. Kichline

The investigation herein described was carried out for the purpose of studying, both by chemical and metallographical means, the extent of over-oxidation of steel that can be accomplished by excessive overblowing in a Bessemer converter. 111 addition there are appended some results of basic open-hearth and crucible steels. Remarks on Chemical Methods. The test block used was hemispherical in shape, 4.5 in. in diameter and 2 in. thick. Drillings for analysis were obtained by drilling through the entire solid part of the block, carefully avoiding all cracks and blow-holes and mixing these drillings thoroughly. Drillinga were carefully examined for scale and the finest were gone over with a microscope to be sure all scale from whatever source had been removed. Oxygen was determined by the well-known method of Ledebur, modified according to Cushman,1 with, however, the removal of the preheating tube, which was found unnecessary. This method has been found to give concordant results. Blanks run from 0.0003 to 0.0006 g. Duplicate determinations varied not more than 0.001 to 0.003 per cent. It seems to be generally supposed that the hydrogen method gives only that oxygen which is combined with iron. Whether this be true or not, the content of oxygen existing as iron oxide no doubt predominates sufficiently, so that the result obtained is sufficient to indicate whether the steel is over-oxidized or not. We are well aware that the oxides of manganese and chromium, when existing alone, are not reduced by hydrogen at a red heat. To learn of their action in steel the following work was carried out: A sample of ferro-manganese and of ferro-chrome were each exposed

Jan 1, 1914

By J. G. Mansanti

The metallurgical response of a deposit's various ore types usually has a strong impact on the flowsheet design of most mineral processing plants. This impacts the materials handling, equipment selection, capital and operating costs, and plant availability. Because of the rapid leaching characteristics of Chimney Creek ores a variation of the conventional gold plant, carbon columns and CIP was proposed. The proposal consisted of a washing stage which was installed between the typical leaching and CIP stages. The circuit was simulated in the lab and was modelled using a computer program to evaluate the metallurgical impact and the effect on the system's mass balances. Also, actual plant data was reviewed comparing the results that were achieved with the results that were expected.

Jan 1, 1988

By Shunhong Huang

Thirty-five soils were sampled from three sites at different distances from chromium slag heap of a Iron-alloy factory, namely, nine from site A located under the chromium slag and eighteen from Site B in the vicinity of the factory and eight from site C far from the factory. The contents of total Cr in these soils from site A, B and C were 1666.0±1310.9 mg? kg - 1,1136.2±1844.6 mg? kg - 1 ,300.4 ±165.1 mg? kg ? 1, respectively. The contents of water soluble Cr were 59.3±77.57 mg? kg ? 1,0.6 ±0.3 mg? kg - 1 ,0.5±0.3 mg? kg - 1 , respectively. In order to evaluate soil health, the activities of four soil enzymes (catalase, polyphenol oxidase, dehydrogenase, alkaline phosphatases) were analyzed. The results have shown that dehydrogenase activity was greatly depressed by conditions in the heavy chromium-contaminated sites. Negative correlation was observed between dehydrogenase activity and the distance from the chromium slag heap, however, the activities of catalase, polyphenol oxidase, alkaline phosphatases in soils from the three sampling sites mentioned above did not differ significantly. The result imply that of dehydrogenase activity could be used as an indicator for the chromium pollution level in the area of Iron-Alloy factory and for the stability level of the soil ecosystem.

Jan 1, 2008

By W. P. Lass

The purpose of this article is not only to describe the plant and method of cyaniding the Treadwell concentrates, but to present some of the results of the experimental work obtained in the past three years for the Alaska-Treadwell Qold Mining Co., at Douglas Island, Alaska, under the direction of F. W. Bradley, Consulting Engineer, and Robert A. Kinzie, General Superintendent, of the affiliated companies. At the time the experimental work was undertaken the concentrates were being shipped to the smeltery at Tacoma, Wash., and the cost for treatment of 3-oz. (gold) concentrates was $11.95 per ton, divided as follows : Smelting-charges,......... $4.00 Loading, freight, insurance, etc., . 2.89 Interest due to time loat in transit and in settlement,... 0.05 Loss due to settlement for 95 per cent. of the gold at $20 per ounce, 6.01 Total,...$11.95 From the experimental work described later, it was estimated that 96 per cent. extraction could be made by treatment on the ground, and that the cost, when treating 80 tons per day, would be $3.25 per ton, divided as follows : Per Day. Per Ton. Labor,. $86.16 $@.827 Chemicals,.76.60 0.960 Power and steam-heat,... 67.60 0.845 Marketing-, refining- and other charges, . 49.36 0.617 Totals,.. $2.59.72 $3.250 Adding to this total the 4 per cent. treatment-loss, which on 3-02. concentrates amounts to $2.48, gives a total cost of $5.13 per ton. Comparing this with $11.95, the cost when shipping to the smelter, leaves a net gain of $6.22 per ton by the local

Jan 1, 1912