Search Documents

By J. H. Wernick, J. E. Kunzler

HIGHLY pure metals are needed for low-temperature electron transport studies in progress. Recent improvements in purification techniques, such as zone refining, have made it possible to obtain metals with improved purity. For some metals, the improvement has been to the extent that ordinary analytical techniques are inadequate and special methods are needed.1 For other metals purification is more difficult, so that simple but rapid analytical methods are desirable as an aid in evaluating the effectiveness of purification procedures. Furthermore, it is desirable to be able to determine the impurity level of the sample or ingot with the minimum of physical disturbance of the material. In order to aid in the preparation of purer metals, techniques involving the measurement of electrical resistance at liquid-helium temperatures have been devised for studying impurity distributions in zone-refined ingots and other bulk samples without destroying the ingot or its geometry. The method yields information on the variations in purity along the length of the ingot or sample and provides a measure of the overall purity of the material. Compared with ordinary analytical methods, the resistivity method is rapid, sensitive, and does not require significant physical disturbance of samples with reasonable shapes. It has the disadvantage that resistance measurements are not specific, i.e., they do not identify the impurity. However, this disadvantage is offset by the advantage of being able to establish a measure of the overall purity so far as electrically active" impurities are concerned. METHOD AND ITS BASIS The method is based on the well-known fact that the resistivity, at Liquid helium temperatures, of a reasonably pure metal containing no regions with additional phases decreases with increasing chemical purity or a decrease in the number of physical defects. It is convenient to separate the total resistivity into three parts: where is the resistivity due to the scattering of the conduction electrons by the lattice vibrations or phonons, p is the contribution due to physical defects, and originates from the effect of chemical impurities in the metal. Insofar as Matthiessen's rule is obeyed,2 pphys and pchem are independent of temperature. Except possiblyin the very purest metals, ptherm is negligible at liquid helium temperatures and For zone-refined metals, which normally are well annealed and consist of large grains, at the chemical purity levels thus far attained the available data indicate that pphys is negligibly small or at least constant throughout the ingot. Assuming that the effect of physical defects is negligible for isotropic metals, This assumption appears consistent with most of

Jan 1, 1959

Aspects of the formation, decomposition and acid solubility of zinc ferrite were examined to find potential ways of increasing the recovery of zinc from a calcination process of mineral concentrates. Ferrite can begin to form within 2 hours at 450¦C. while complete reaction can occur after 35 minutes at 700¦C. The nature of the starting materials has a pronounced effect on the rate of formation and below 700¦C. ZnSO4 and Fe2O3 proved to be the least reactive of the materials investigated. It is possible that iron in a mineral admixed h sphalerite can be converted to a relatively inactive form, however, it does not seem possible to prevent zince f formation when iron is in the sphalerite lattice. At the two temperatures examined, 650¦C. and 700¦C, the presence of SO2 in the atmosphere accelerate .e formation of ferrite. Prolonged exposure to such atmospheres, however, caused the ferrite to decompose to ZnSO4 and Fe203. The optimum temperature for decomposition was 650¦C. and it was virtually complete within 2 hours in an atmosphere of 10% SO2 in air. Zinc ferrite was also decomposed by CO at low concentrations, and by heating with limestone at 1000¦C. for at least 2 hours. The solubility of zinc ferrite in acid was influenced by the starting materials used. As both the reaction temperature and the time at temperature increased the acid solubility decreased. The acid solubility was a minimum when the ___i_.. n - I -r~...................c -..... F, fe..i+e --A frn... A01- +^ Z(lo/

Jan 1, 1970

By Porter W. Shimer

Ox completing the filtration of a solution of pig-iron in hydrochloric acid, and after apparently everything had been transferred to the paper, a minute residue was observed remaining in the angle of the beaker in which the solution had been made. This residue had a steel-gray color and metallic luster and was hard and gritty when touched with a glass rod. Placed under a microscope and magnified 400 diameters, the substance was found to be made up almost entirely of opaque cubical crystals with some fragments having the same color and luster as the cubes. The appearance was strikingly like that of a collection of crystals of iron pyrites. The amount of material obtained from ten to twenty grams of borings by solution in dilute hydrochloric acid, and careful decantation from graphite, was barely sufficient for a microscopic slide. A qualitative test of the minute amount of material obtained in this way, showed the presence of considerable titanium. After many fruitless trials by decantation and other methods, sufficient material for quantitative analysis was finally obtained in the following manner: Two hundred and fifty grams of the coarsest possible borings were dissolved in seven liters of hydrochloric acid of sp. gr. 1.03. A solution by the aid of heat took four to five hours. It was allowed to settle, and the clear solution poured off. Great care was taken that none of the material which had settled to the bottom was lost. The graphitic residue was then completely transferred upon fine bolting-cloth, previously Stretched and fastened over the top of a beaker. All graphitic lumps were broken up by the finger while

Jan 1, 1887

FRank FirmstoNe, Easton, Pa.: The effect of lead on brass seems to have been recognized by Berthier, and the facts published by him as early as 1818 (Ann. des Mines, 1st ser., iii., 1818, p. 347 et seq.). He there says expressly that copper containing lead makes " dry " (see) brass, and that, for the same reason, blast-furnace

Jan 1, 1898

By A. W. Sommer, H. H. Kellogg

It is shown that SO3-O2 mixtures react with sphalerite at an appreciable rate ill the temperature range of 361° to 527°C to fornz ZnSO4. The rate of reaction follows a parabolle lax. Oxygen, or O2-SO2 mixtures, have a negligible effect on sphalcrite in the same temperatuee range. PRACTICAL roasting of sphalerite is usually performed at 800°C or higher. The calcine is composed of zinc oxide unless the roaster atmosphere contains relatively large amounts of SO2 and the temperature is held to 800oC or lower, in which case zinc sul-fate may also form. Ong, Wadsworth, and assell' have made a careful kinetic study of sphalerite oxidation under these "normal conditions" and have concluded that the rate of the reaction is controlled by the decomposition of an activated complex adsorbed on the sphalerite surface. They found the rate of oxidation to be small at 700°C. Extrapolation of their data to 400°C would indicate an almost negligible rate at this temperature. In our work sphalerite was reacted with air, mixtures of SO2, O2, and N2, and mixtures of SO3, O2, and N2 in the temperature range 361o to 527OC. Negligible rates of oxidation were found, except for the gas mixtures containing SOs. With this latter gas, the oxidation of finely divided sphalerite was fairly rapid and zinc sulfate was the product. Based on the limited evidence available, the rate of sphalerite oxidation by SO3 is postulated to be controlled by gaseous diffusion through pores or cracks in the zinc-sulfate coating. This evidence for the direct reaction of sphalerite and SO, at low temperature may prove of importance to the understanding of zinc-sulfate formation in the dust-collecting equipment usually associated with zinc roasters. The roaster gas carries off fine dust, much of which may be unreacted sphalerite. The temperature in dust-collecting equipment drops from the roaster temperature (about 800°C) through the range of temperature we studied, to ambient temperature. Such dusts are known to contain far larger amounts of zinc sulfate than the primary calcine. It has been assumed in the past that this sulfate is formed by reaction of ZnO dust with SO3 (or SO, plus 0,) in the partly cooled gases. Our work shows that an alternative possibility exists—the direct reaction of SO3 with ZnS dust. EXPERIMENTAL Reaction rates for sphalerite at 350° to 600°C are relatively small so that it was necessary to use finely divided material with a relatively large surface area in order to obtain measureable amounts of reaction. In the preliminary experiments, pure mineral sphalerite, ground to pass a 325-mesh sieve, and chemically precipitated ZnS (in the form of an impalpable powder) were used. In the quantitative rate experiments the ground mineral sphalerite was processed in an Infrasizer to obtain a product with particle size between 9 and 18 µ. The analysis of this material was 66.7 pct Zn, 0.09 pct Fe, and 32.7 pct S (theoretical sphalerite is 67.1 pct Zn, 32.9 pct S). The sized powder was carefully mixed and divided into l-g samples. The apparatus used for the quantitative rate measurements is shown in Fig. 1. For the preliminary experiments the following change was made: The external catalyst furnace (B, C)* was not used. *Letters refer to Fig._______1 .___- Rather, when catalysis of the SO2 + O2 reaction was desired, the glass beads in basket M were replaced by vanadium-oxide pellets. Procedure—A l-g sample of ZnS was placed on a shallow stainless-steel tray, I, and spread evenly to a depth of about 1mm. The tray was placed in the reaction assembly and the assembly inserted in the cold furnace. The furnace tube was flushed with dry argon and then heated to the desired reaction temperature. The temperature was controlled to ±0.5oC. Gas mixtures (O2 + N2 or O2 + SO2) were prepared from tank gases by means of a mixing device identical to that employed by Darken and Gurry.2 The total flow rate of gas was 205 ml per min to point A of Fig. 1. The accuracy of the individual and

Jan 1, 1960

By D. H. Baldwin, R. E. Reed-Hill

Six compositions of polycrystalline ZY-0 alloys, containing up to 4.2 at. pct 0, were tested in tension between 77° and 600° K. The data obtained from each of the compositions corresponded closely to a rela-ion between yield stress and absolute temperature of the form In s/so = BT, where oo is the yield stress extrapolated to zero degrees and B is a constant. In agreement with others who have observed this relationship, it is shown that the activation energy may be expressed as Ho In so/s. In the present specimens Ho is approximately 18,000 cal per mole and is apparently independent of temperature and composition inside the limits of the investigation. It is also demonstrated that this form of activation energy cowesponds to a strain rate sensitivity parameter RT/Ho. Oxygen was also noted to have an effect upon the operative deformation mechanisms. With increasing oxygen concentration there was an increased tendency to observe both nonbasal slip and cross-slip phenomena. Oxygen does not seriously inhibit twinning more than it does slip. Twins were observed in all specimens tested. It is becoming increasingly evident that interstitial atoms in solid solution are able to interact strongly with mobile dislocations. Stein, Low, and seybolt,&apos; have shown that, if the carbon concentration in bcc iron is lowered below the solubility limit, its flow stress temperature dependence is markedly reduced. This suggests that carbon atoms in interstitial solid solution may be responsible for the pronounced temperature dependence of the flow stress normally observed in iron. This view has recently been challenged by Leslie and sober2 who observed a strong flow stress temperature dependence in iron to which a trace of titanium had been added in order to remove carbon atoms from solution. Since the interstitial concentration must be reduced below approximately 1 ppm in order to produce a pronounced effect on the flow stress temperature dependence,&apos; studies of the effect of interstitials on the flow stress in iron necessarily involve serious experimental difficulties in alloy preparation. There are other metals, however, in which strong effects of interstitial solutes upon both the flow stress and its temperature dependence are observed. Of particular significance is zirconium which, according to Domagala and Mcpherson, 3 is capable of dissolving 28.6 at. pct O. The O-Zr alloy system is an almost ideal system for studying the interaction of interstitial atoms with deformation modes since it is possible to form alloys capable of study over an extensive range of compositions. Mills has made such a study using single crystals oriented primarily for single prismatic slip4 and has found an effect of oxygen concentration on the flow stress temperature dependence analogous to that observed in iron due to carbon by Stein, Low, and Seybolt. The present paper is specifically concerned with the effect of oxygen on deformation in polycrystalline zirconium. Although plastic flow in this type of specimen is much more complex than that reported for the single-crystal work, and involves both slip (on several different types of planes) and mechanical twinning, the results of this investigation are in general agreement with the single-crystal observations concerning the effect of oxygen on the temperature dependence of the flow stress. In addition, they also demonstrate that oxygen affects the acting deformation systems. This is in contrast to single-crystal results4 that showed only single slip on a prism plane. EXPERIMENTAL PROCEDURE Material. High-purity hot-rolled zirconium strip, 0.2 in. thick by 4 in. wide, of 0.10-mm average grain diameter, was used for forming alloys. It was obtained from the Carborundum Metals Co., Akron, N.Y., whose analysis indicated the major impurities were, in wt ppm: Hf, 540, C, 145; Fe, 100; and 0, <80. The plate texture was similar to a wire texture, with basal planes generally parallel to the rolling direction and basal poles randomly distributed about the rolling direction. The heat treatments described below did not appreciably alter the basic texture. specimen Preparation. Small threaded-end tensile specimens were machined from the plate with axes perpendicular to the rolling direction. These transverse specimens had gage sections 1 in. long by 0.060 in. in diam. The small gage section diameter was dictated by the fact that the alloys were formed by dif-

Jan 1, 1969

By C. H. Li, R. D. Carnahan, R. J. Stokes, T. L. Johnston

When silver chloride deforms by pencil glide at temperatures of 26ºand 72°C, grain size has no effect upon the proportional limit and the material necks down to a knife edge under tension. At -196ºC, deformation takes place on fewer slip systems to produce straight slip traces, the flow stress becomes sensitive to grain size and fracture occurs by cleavage from an intergranular source without any reduction in area. THERE are significant differences between the appearance of the slip bands formed in silver chloride and in the alkali halides at room temperature. The bands in sodium chloride, e.g., are fine and geometrically straight, whereas in silver chloride they are coarse and wavy.&apos; Such differences in the slip behavior prompted us to inquire what the effects of grain boundaries might be on the mechanical properties of these solids. As an introduction to a general study of ionic poly-crystal behavior, we have investigated the effect of grain size on the stress-strain relationships in silver chloride at different temperatures. We have chosen silver chloride chiefly because polycrystals can be easily prepared free from cracks and macroscopic voids by conventional techniques. Moreover, as we shall see, the slip behavior can be readily modified by changing the temperature. It will be shown that the effect of grain size on the yield stress of silver chloride is strikingly dependent upon the temperature of deformation and that this temperature effect comes about through a change in the number of slip systems which operate at the onset of plastic flow. EXPERIMENTAL PROCEDURES Polycrystalline tensile specimens were made by recrystallizing cold-rolled AgCl sheet. Thirty-gram quantities of AR grade silver chloride powder were melted in a low heat capacity furnace, cast into cylindrical forms 3/4 in. in dim and approximately 1 in. in length and then extruded with a 16:l reduction ratio into rods 3/16 in. in dim. Extrusion temperatures were varied from room temperature to 350°C. In order to impart various degrees of cold&apos;work to the extruded rod. All extrusions were then cross rolled to sheet 0.040 in. in thickness at room temperature and machined to form tensile specimens having a gage length of 0.750 in. with a width of either 0.250 or 0.145 in.* Annealing was carried out in an air oven at 200°C for periods up to 20 hr. specimens having average grain diameters ranging from 0.024 to 0.40 mm were prepared by varying the extrusion temperature and annealing time in the conventional manner. To obtain specimens with grain sizes larger than 0.40mm, lightly deformed thin prisims of silver chloride single crystals (supplied by Harshaw Chemical Co.) were recrystallized. Grain size determinations were made by an intercept method and revealed that the grains were equi-axed. Laue back-reflection X-ray patterns showed little tendency to form a preferred orientation texture. Specimens which were to be used for the slip band studies were polished by immersion in fresh boiling concentrated NH,OH for 60 sec. They were then etch polished for 10 sec on each side by hand lapping on a stationary velveteen lap wetted with a dilute Hypo solution (5 g of Kodak Acid Fixer in 100 cc H20). Finally the specimens were rinsed in warm water and alcohol, blown dry and carefully mounted in the tensile machine for testing. Tensile tests were performed at three temperatures, namely, 26º, -72º, and -196°C. A screw-driven hard tensile machine was used at a constant strain rate of 0.006 in. per in. per min. Loads were determined with a light- proof ring fitted with A-18 strain gages and extensions were measured with a 0.0001 in. dial gage. Constant level baths of alcohol with dry ice and liquid nitrogen were used to maintain the two lower test temperatures. EXPERIMENTAL RESULTS Reproducibility—In view of the light sensitivity and reactive nature of silver chloride, it was necessary to determine whether reproducibility depended upon either exposure to light or to the condition of the surface. However, during the course of the work it became clear that variation of laboratory lighting

Jan 1, 1962

By R. F. Janke, J. F. Bossler

Introduction The commercial use of ion exchange resins to recover uranium evolved in the decade following 1950 when significant efforts were made to recover this vital element economically and efficiently from low grade ores. It was discovered that in both acid and alkaline systems, uranium exists as an anionic complex. This led to the application of anion exchange resins to concentrate and purify the uranium product. While this is the simplest statement of what an ion exchange resin does in the recovery of uranium, it should not be forgotten that the industry is continuing to evolve new methods in mining and processing which affect ion exchange operation. The inception of solution mining, the use of expanded bed ion exchange columns and the development of continuous ion exchange systems represent several examples of this continuing evolution in the industry. Throughout all of the changes in equipment designs and variations in solution compositions, the purpose of the ion exchange resin remains the same - to concentrate and purify uranium. Ion Exchange Resins When evaluating ion exchange resins for a uranium recovery project, the task that faces the chemist or process metallurgist is an assessment of the efficiency and, therefore, the economics of the various candidate resins for a given project. This assessment should include consideration of both physical factors such as particle size, density, hydraulic expansion and pressure drop as well as chemical factors such as the uranium loading and elution characteristics. For any given application, the differences in the physical and chemical behavior of ion exchange resins are a function of the conditions used to manufacture those resins. Therefore, an understanding of the way in which manufacturing variables affect resin behavior is important. Since most uranium recovery projects are concerned with recovery of the anionic complexes of uranium using anion exchange resins, this discussion will be restricted solely to the family of anion resins. The majority of the ion exchange resins used in commercial recovery operations look similar to the resins shown in Figure #1. [ ] Most of these materials are based on a styrene- divinylbenzene copolymer. The liquid monomers, styrene and divinylbenzene, are charged to a co-polymer reactor containing water. The water insoluble monomers are then mixed with the water to suspend oil-like droplets of the monomer mixture in. the water. The entire reaction mixture is then heated causing the monomers to polymerize into sol id thermoset plastic spheres. The spherical nature of the particle, the particle size distribution and the primary crosslinking level are fixed in this step in the production process. Figure 2 is a simplified illustration of this step of the process. [ ]

Jan 1, 1979

By B. N. Das, H. E. LaBelle, G. A. Wolf

ZnxHg1-xTe and GUPxAS1-x crystals have been grown from solution by a traveling heater method (THM). In a floating zone type fashion a solution zone sandwich of liquidus composition is made to migrate through feed material of solidus composition by a slow-speed movement of <0.25 mm per hr of the total charge through a stationary radiation or rf heater. ZnxHg1-xTe of composition 0 < x < 0.3 and GUPxAS1-x of composition 0.5 < x < 0.7 have thus been grown from their solution in liquid tellurium and gallium, respectively. A simplified analysis of heat and material transport is given. In this method, Proper adjustment of the temperature distribution along the liquid solution zone axis eliminates instability of the crystal growth front and constitutional supercooling. 1) ZnxHg1—xTe: The solid-solution telluride was grown in sealed quartz tubes at a temperature of 500 to 650°C. For first Preparations mechanical mixtures SINGLE crystals of solid solutions of III-V and II-VI compounds have been grown by various techniques from the melt, from the gaseous phase, or from solutions in of ZnTe and HgTe were used. X-ray determinations showed the resulting crystals to be homogeneous throughout their entire length, except for the end sections. The homogeneity is greatly improved by reusing the ingots obtained from first Preparations as feed material in subsequent crystal growth runs. Ingots of up to 4.5 cm have thus been obtained. 2) GaPxAs1-x: Crystals were grown in a EN crucible at a temperature of 1050°C. For first Preparation a mechanical mixture of Gap and GaAs was cemented together by a minimum amount of liquid gallium through "wet" grinding of Gap and GaAs crystals in the liquid metal and subsequent exuding of excess gallium by compacting of the charge in the EN crucible. Electron microprobe measurements using P-Ka and As-Ka radiation showed uniformity over a length of 0.4 cm. Properties of the various Preparations are described. liquid metals.&apos;-&apos; Their growth from the melt by passing a liquid zone of pseudobinary liquidus composition through a solid rod of solidus composition is generally a convenient method of growth of single crystals of solid solutions of homogeneous composition. This method loses much of its usefulness, however, if the melting point or the vapor pressure of the solid solution is high. In the case of a compound having a high melting

Jan 1, 1969

By William Lodding

Muscovite was the crystalline material used in the experiments discussed in this paper. It was both wet and dry ground for various periods of time. The effects (physical and chemical changes) produced in grinding are analyzed by use of thermal analysis. That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Mackenziel and Bartha2 reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding and, on the other hand, existing strain may be released by the same process, as shown by Holt, et a1.3 All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze, by the use of thermal analysis, some effects produced in grinding. In differential thermal analysis (DTA) one measures the sum of all thermal changes occurring in a substance during heating or cooling; e.g., chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and thermal conductivity, strain release, etc. By thermogravimetric analysis (TGA), on the other hand, only chemical changes involving weight loss or gain are recorded. Similarly, gas evolution analysis (GEA) will register only reactions involving gas evolution. By performing two or all three of these methods of thermal analysis simultaneously and on the same specimen, one can separate the different effects registered and, by difference, evaluate their magnitude. The results of TGA are usually plotted as percent weight against furnace temp. When one differentiates weight against furnace temp, a rate of weight-change curve is obtained, and the resulting differential thermogravimetric (DTG) plots are similar in appearance to DTA thermograms for the same reaction. While the integrated area under a DTA peak represents enthalpy and can be expressed in calories per gram the area under the corresponding DTG peak represents the weight change which took place during a reaction. The similarity of DTA and DTG thermograms obtained from one material can be seen in Figs. 1 and 2. EXPERIMENTAL A Fisher mortar grinder and a porcelain mill with burundum balls were used for both dry and wet grinding. Muscovite was first carefully hand-filed and screened on 20 and 100 mesh. The middle fraction was considered essentially unaltered muscovite.

Jan 1, 1968

By G. K. Engelhart

A multi-stage counterflow process developed in Germany preheats dry pulverized portland cement raw materials held in suspension in rotary kiln waste gases. Capacity of the first kiln installed for this purpose in the United States has been increased from 860 to 1500 bbl per day, with fuel reductions from 1,100,000 Btu to 650,000 or 700,000 Btu per bbl. Sixty percent of total waste gas is used. As full use of the gas stream is approached, additional kiln production and fuel economy may be expected. EFFECTIVE use of rotary kiln waste gases to preheat dry pulverized materials has been demonstrated in full-scale operation at the Allentown Portland Cement Co. plant, Evansville, Pa. Pulverized raw materials are preheated in suspension in the gas stream in a multi-stage counterflow process which draws the gases through a series of cyclone collectors. Upon entering the first cyclone stage the material, continuously delivered and suspended in the gas stream, is successively collected and re-suspended until it discharges through the kiln feed pipe. Gas and material contact time is thus prolonged, providing a high degree of heat recuperation with a very low temperature differential between gas and material at the final stage. The suspension preheater, developed by Klock-ner-Humboldt-Deutz AG of Cologne, Germany, was first installed at the Norddeutsche Huette plant, Oslebshausen, Germany. Similar preheaters are now in operation at three other German cement plants. The first American installation, at the Allentown Portland Cement Co. plant, was designed and manufactured by Fuller Co. of Catasauqua, Pa., Humboldt&apos;s licensee for the United States, Canada, and Mexico. Design of this installation is essentially the same as the German original, but provision was made for varying the method to adapt the process to specific objectives of American portland cement production. Differences between German and American cement clinker production practices are directly related to differences in three primary production cost items: fuel, labor, and power. Because fuel costs are high in Germany and elsewhere in Europe, thermal efficiency has been the first objective of European cement producers and manufacturers of rotary kilns. The Germans have developed such recuperative equipment as the present suspension preheater, the Miag calcinator, and the Lepol kiln, the invention of 0. G. Lellep. In North America labor is the principal cost item, although rising fuel costs are of growing concern. High clinker production is therefore of first importance. Recent installations of longer dry process cement kilns have been disappointing, failing to make satisfactory reductions in exit gas temperatures when production is held at an acceptable level. The Humboldt suspension preheater satisfies both

Jan 1, 1955

By R. V. Ramani, A. S. C. Owili-eger

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to December, 1973. This report was submitted by the authors on March 31, 1974. Part of the research reported here was originally done on a grant from the Department of Environmental Resources, Commonwealth of Pennsylvania and reported in Special Research Report No. SR-95 (February 25, 1973) of the Coal Research Board, The Pennsylvania State University.

Jan 1, 1974

By J. G. Kura, P. D. Frost, L. W. Eastwood

THE preparation and general properties of mag-nesium-lithium base alloys have been described in earlier papers.l,2 Lithium forms solid solutions with pure magnesium, lowers its density, and improves its formability. The improved isotropy and better formability of these alloys are attributed to the ability of lithium to convert the magnesium lattice from hexagonal (alpha phase) to body-centered-cubic (beta phase) structure. This change in structure is, however, accompanied by some limitations which make it difficult, if not impossible, to combine all the desirable properties in one composition. The most important of these limitations is the tendency of the high-strength alloys to overage and lose strength at temperatures of the order of 150" to 200°F. A study was made of the effects of composition and heat treatment on the age-hardening character- istics of the alloys. Stability of properties was determined by hardness and tensile testing of the alloys at room temperature after various periods of exposure to elevated temperatures. Precipitation-hardening curves are shown for a number of magnesium-lithium-zinc alloys in fig. 1. All the alloys were solution treated at 700°F and aged at 200°F. The reason for using the drastic quench, toluene at —105°F, was to reduce the rapid precipitation of the hardening phase which takes place at room temperature. Previous experience has shown that a hardness of about 90 to 95 Rockwell E is indicative of yield strengths in the range of 35,000 to 40,000 psi. This is a desirable strength level for magnesium-lithium base alloys with specific gravities of the order of 1.65 or less. Although the hardness level is raised by large zinc contents, a corresponding decrease in the cold formability of these alloys occurs with increasing zinc content. Thus, alloys containing up to about 10 pct Zn and having hardnesses of the order of 70 to 75 Rockwell E may be bent over a very small radius; however, the 16 pct Zn alloy requires a bend radius of more than 8T. The hardness relationships illustrated in fig. 1 can be explained by the partial phase diagram shown in fig. 2. The zinc-free magnesium-lithium alloys are entirely body-centered cubic (100 pct beta phase) when the lithium content of the binary is 10.3 pct or higher. When zinc is added, the boundary between the beta and alpha-plus-beta fields at 700°F is shifted to lower lithium contents. In addition, the solubility of zinc at 700°F decreases with decreasing lithium content. It is shown by a study of micro-structures that the limit of solid solubility of zinc in the 6Mg/Li* matrix at 700°F is about 19 pct. It is believed from a study of the aging curves that this limit is about 2 to 3 pct at 200°F. Zinc additions up to about 2 pct increase the hardness and strength of the magnesium-lithium base solid solution. Larger additions of zinc effect further hardness increases, but precipitate during prolonged aging at 200°F. Alloys having 14 to 20 pct Zn precipitation harden extremely rapidly during quenching, even when quenched in toluene at —105° F. The high-zinc alloys overage at 200°F but are capable of maintaining reasonably high hardnesses for periods up to 1000 hr.

Jan 1, 1951

By M Chen, G H. Wang, J R. Zhou, P Yan, W B. Lu

Blast vibration analysis is one of the important topics in the control technology of blast vibration damage. Nowadays, blasting vibration safety standards are based on both the particle velocity and the frequency of vibration and they have been adopted widely and internationally. However, the analysis on vibration frequencies is less studied compared to investigations of peak particle velocity. For the vibration induced by a spherical charge in a viscoelasticly infinite rock mass, an expression of vibration spectrum taking into account the damping effect of rock mass is inferred. Then the attenuation laws of dominant frequencies and centroid frequencies are compared theoretically. For the case of cylindrical charge, dynamic finite element method (DFEM) software of LS-DYNA is employed to analyse the attenuation laws of characteristic frequencies. The research demonstrates that, no matter whether it is a spherical charge or a cylindrical charge, there is a local mutation or fluctuation at some distance when the blast proceeds, while the centroid frequencies conform to a smooth attenuation law. Both the multipeaks structures of vibration spectra and the decay rate difference between high- and low-frequency components contribute to the mutation or fluctuation investigated in this study. Additionally, an increase in longitudinally sonic velocity or the quality factor of rock mass produces an increase in the vibration frequencies, whereas an increase in blast source diameter or the rise time of blast load produces a decrease in vibration frequencies from a spherical charge. In borehole blasting, there is a positive correlation between the vibration frequencies and charge diameter, whereas there is a negative correlation with charge length. And altering the initiation plan will change vibration frequencies to various degrees. Finally, theoretical analysis results were validated by the empirical data from field experiments of Fengning pumped storage power station.CITATION:Zhou, J R, Lu, W B, Chen, M, Yan, P and Wang, G H, 2015. A further study on the attenuation laws of blasting vibration frequency, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 673–682 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The Tertiary gold deposits of the Hauraki area are predominantly epithermal vein types containing mineral assemblages of quartz, calcite, pyrite, sphalerite, galena, chalcopyrite, acanthite and native gold (electrum). Sulphosalt, telluride (eg hessite), seleniferous sulphide and selenide minerals are important locally. Studies of wall rock alteration mineralogy, fluid inclusions in gangue minerals, and sulphur isotopes of sulphide minerals indicate that the ore forming fluids had the following parameters: pH, near neutral at depth but acidic near surface; temperature, predominantly 320 - 270¦C for base metal dominated assemblages, 280 - 200¦C for precious metal dominated assemblages and generally below 200¦C for late stage barite; apparent salinity, six to zero equivalent weight per cent NaCl; and CO2 concentration, generally around&nbsp;one mole per cent CO2. There is fluid inclusion evidence for boiling during mineralisation in some deposits. Moderate values off S2 and FO2 are indicated for base metal and mixed base metal&nbsp;û precious metal assemblages of most deposits by the predominance of pyrite + chalcopyrite over other iron-bearing phases; primary bornite is absent, whereas pyrrhotite, hematite and magnetite rarely occur in the veins. The largest gold&nbsp;û silver deposits formed from solutions in which the sulphur species in solution were predominantly reduced. Near surface environments and some deep, predominantly base metal, deposits were formed from solutions with approximately equal concentrations of oxidised and reduced sulphur species.

Jan 1, 1984

By Pan Zhao, Yan-Nan Wang, Fei-Long Liao, Can Cai, Kai-Song Wu

"What are the basic physical parameters and main geometric parameters that are capable of representing the microscopic characteristics of rock? How can these parameters be used to accurately describe the macroscopic mechanical behavior of rock? With such questions in view, and based on the microcosmic structure analysis of rock slices, this paper presents a rock skeleton-pore structure model, holding that rock's mechanical behavior depends on the properties of rock skeleton materials and the form, size and distribution pattern of pores. According to rock stress and deformation behaviors, and in line with the skeleton-pore structure model, an essential mechanics theory for rock is advanced. The assumption that the skeleton materials are incompressible in volume and an introduction of logarithmic strain, generate the relation between porosity and apparent strain. Then, the notion that positive damage and negative damage are represented in terms of porosity is put forward; threshold value of porosity is derived by the damage threshold value of apparent volume strain; a general damage variable of rock is obtained; eventually, with the skeleton-pore model as the groundwork, a global damage constitutive equation is developed, which, with definite physical significance and material parameters to be easily determined, is convenient to apply. It has been proved that the results calculated with this new equation are well in agreement with experimental results.INTRODUCTIONRock is a form of material that contains pores, cracks and skeletons. Skeletons are composed of particles and cements. Pores or cracks within rock actually undermine the assumption of material continuum in solid mechanics. Hence, grave errors — or even false results — are inevitable if some solid mechanics theory is quoted in the discussion of rock mechanics. Many researchers in the field of rock mechanics have attempted various remedies, but the outcome is far from satisfactory — a mechanics theory for rock, in its true sense, has not been established."

Jan 1, 2015

By F. G. Crack, R. V. Ramani, R. L. Frantz

Management for mine construction and development differs from that needed for routine mine production and maintenance. An integrated approach to managing mine development projects must consider contract documents; management organization of a project; the project manager&apos;s role and the field supervisor&apos;s responsibility; and the use of scientific techniques for planning, scheduling, executing, and controlling projects. Professional project management encompasses the following: • Preparing contract documents that establish technical and financial schedules, and detail the responsibility for the physical work commitment. • Developing a project&apos;s organizational structure, to clearly define the roles of the project manager and the field supervisors. • Establishing project management and field supervisor relationships, to avoid ambiguity in assigning responsibility and to ensure desired project progress. • Using management science techniques, particularly networking techniques such as the critical path method for planning scheduling, executing, and controlling projects. Project Versus Production Management Project management differs from routine production management in the following ways: • Uniqueness: A project is unique. Production operations tend to be repetitive. The magnitude of one-time capital expenditures for many facets of mine development warrant special skills and attention. These professional project development skills must already be available by prior experience in the management team. • Personnel: In projects, personnel are usually assigned on a specialty basis and frequently change with the project activity. On the other hand, production personnel work together, more or less permanently. • Management Structure: In a project there may be several staff-line relationships that are not clearly defined and change with changing project activities. In a production situation, the lines of communication and authority are usually well defined. • Time Frame: A difference between project and routine production management is that project activities have comparatively less well defined durations and often tend to be relatively short-term. Production usually has both long-term and short-term plans and well defined long-term and shor-term goals. In project management, formal, critical, short-term reviews are frequently required. In production management, five year plans can be formally adjusted quarterly and annually. Short-term weekly or daily reviews can be informal. • Response to Delays: Delays in a development project may occur without anyone being immediately aware of their existence or suspecting the magnitude of consequence. In contrast, any delays in the production process can be easily identified from prior results comparison. Additionally, the response is quick, usually in a set routine. This can be traced back to the management structure and personnel. • Control Techniques: Measurements of project progress for control are not easily made due to the variety of activities that are carried on at the same time by different work groups. The yard-sticks of performance measurement for individual activities, let alone for the total project, are not easily established. However, due to the difficulty in detecting project delays, a workable control system is vitally important to a project manager. To apply a scientific project control technique such as "management by exception" requires specific planning and monitoring from the project manager for each activity in the project. Production and productivity are quick and effective yard-sticks of measuring performance in a routine operation. Control techniques required in production management usually revolve around these measures. Construction Contracts The construction contract is an important document that establishes contract scope, technical and financial details of the work, and achievement deadlines. It may also serve as the contract document to pay for work done and to verify field progress with planned progress. In practice, it is a good idea to develop a job-specific contract. This whole area is replete with legal precedence and procedures, and it is not the intent here to deal with the intricacies of establishing a contract document. But it is necessary to have an understanding of major contract types. Construction contracts are extremely important legal documents. They may vary in work specifications and enforcement of the provisions. Due to their nature, they must be composed with legal help and will take some time to compile. Even with all the precautions and provisions, it is not uncommon to find owner and contractor disagreeing. Therefore, it is important to include a way to resolve any difference quickly and to incorporate aspects of the contract as part of an overall management control tool for efficient project management.

Jan 7, 1982

By Bill A. Hancock

In Situ leaching for the recovery of uranium from low grade sandstone deposits is one of the newest technological advances in the mineral industry. It is rapidly developing into a commercially feasible mining system which has economic, environmental, and social advantages over conventional mining systems. Because of the current uranium shortage, development of In Situ leaching into a sophisticated system has gained new impetus. In Situ leaching will become an important mining technique in the future, which will greatly help to supply uranium for our nation&apos;s energy heeds. In this paper, I will be giving an overview of the merits of the system, as well as the technology, problems, and research in solution mining of uranium.

Jan 1, 1977

By R. F. Domagala, M. Hansen, D. J. McPherson

Iodide zirconium was combined with calculated amounts of nitrided zirconium sponge and arc melted to prepare alloys in the 0 to 6 wt pct N region. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat-treated specimens permitted construction of the binary phase diagram from 0 to 6 pct N. Features of the diagram include the peritectic formation of both a and ß solid solutions. The maximum solubility of nitrogen is 0.8 pct in 8 zirconium and 4.8 pct in a zirconium. An X-ray study of nitrided materials was made in the range 6 to 13 wt pct N region because serious nitrogen losses were experienced when attempts were made to arc melt these high nitrogen alloys. PHASE relationships in the Zr-N system have been determined. Due to the inability to retain nitrogen in nitrogen-rich alloys subjected to arc melting, definitive work was possible only in the range 0 to 6 wt pct (0 to 30 atomic pct) N. Sufficient complementary X-ray work was done to permit construction of the binary phase diagram up to 13.3 wt pct (50 atomic pct) N (ZrN). Small ingots were prepared by arc melting master alloys with enough zirconium to produce an alloy of the desired composition. Following pretreatment, alloys were annealed at temperature levels between 600" and 2020°C. Determination of the phase boundaries was then accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to corroborate solidus curves, and X-ray diffraction was employed to study the nitrogen-rich region of the a + ZrN phase field. Materials Westinghouse Grade 1 iodide zirconium crystal bar served as the base material for this investigation. The as-received bars were lightly sandblasted, pickled in a 20 pct HN0-5 pct HF aqueous solution, rinsed in water and acetone, and dried. They were rolled to about 1/32 in. strip and acid-pickled, followed by water and then acetone rinses. The material was sheared to approximately 1/4 in. squares, cleaned with acetone, and stored for use. Pure zirconium nitride is not commercially available, according to correspondence with possible suppliers. A literature survey indicated that nitrogen may be introduced into zirconium metal by passing nitrogen or ammonia gas over zirconium at an elevated temperature. After considerable experimentation, a train was devised whereby high quality nitrogen was passed through a series of bubblers to remove the last traces of oxygen, through an H,SO, bubbler and a cold trap to remove moisture, and finally over zirconium within a resistance furnace. Hand-picked Bureau of Mines magnesium-reduced zirconium sponge proved more amenable to nitriding than the crystal bar. The nitrogen used was extra pure gas purchased from Linde Air Products Co. The first two bubblers through which the gas was passed contained a solution suggested by L. F. Fieser" as being ideal for removing the last traces of oxygen from nitrogen. The solution contains 20 g KOH, 2 g sodium-anthraquinone ,9-sulphonate, and 15 g NaHSO, dissolved in 100 ml water. It is blood-red and turns brown when contaminated with oxygen. A saturated lead acetate solution, next in the series of bubblers, removed any H2S which might have formed in the 0, removal stage. An H,SO, bubbler and cold trap removed moisture before the nitrogen was passed over the zirconium. The zirconium was contained in a stainless steel screen within a Vycor or quartz tube in a resistance furnace. Unreacted nitrogen passed out of the system through a mercury bubbler. A nitriding run was performed in the following manner: Zirconium was placed in the screen within the furnace tube. The unit was assembled, suitably clamped off, and evacuated to remove the air and moisture within the tube and that trapped by the zirconium sponge. The unit was flushed with nitrogen and evacuated twice. After nitrogen was allowed to pass over the zirconium for about 30 min, the furnace was turned on; several hours were required to reach temperature. The reaction was allowed to continue at temperature for about 4 hr and the screen was then withdrawn from the hot zone of the furnace by means of a Nichrome or Kanthal rod. The screen and its contents were allowed to cool at the end of the tube and were then removed. At 800°C no more than about 5 pct N could be introduced into the sponge zirconium. This material was designated M-1 (master alloy No. 1) and reserved for the preparation of alloys in the dilute nitrogen region. A second set of experiments was conducted at 1000°C; no more than 7.2 pct N could be introduced into the zirconium at this temperature. Enough material (M-2) of this nitrogen content was prepared to produce a second set of alloys to complement the first and to provide alloys in the 0 to 6 wt pct N range. It was hoped that a diffusion anneal plus a re-nitriding might yield a material of higher nitrogen content. The material containing about 7 pct N was therefore given a homogenization treatment at 1000°C for 6 hr under an argon atmosphere. It was

Jan 1, 1957

By E. G. Valdez

Three cryogenic systems that utilized liquid nitrogen, dry ice, and methanol with dry ice were investigated in conjunction with crushing and classifying techniques. The systems were used to aid in separating and reclaiming the metallic components contained in insulated wires, shredded automobile nonferrous metal concentrates, small motors, generators, and rubber tires. Wire strands, 2 to 6 inches long and insulated with polyvinyl chloride and neoprene, were chilled at -60° and -195° C, then roll-crushed and processed by water elutriation; this procedure resulted in two products--a sink fraction that was 99 percent metallic and a float fraction that was 99 percent nonmetallic. Excellent separation of zinc die-casting alloys from copper and aluminum contained in shredded automobile nonferrous metal concentrates was attained by chilling at -72° C for 1 minute, crushing in a grateless hammer mill, and screening. From the screened products, 97.2 and 100 percent of the copper and aluminum, respectively, were recovered in the plus Pinch fraction, and 100 percent of the zinc was recovered in the minus 1-inch fraction of over 97 percent zinc die-cast purity. Laboratory experimental results comparing direct and indirect chilling indicated that a sufficiently low temperature could be attained by indirect chilling to permit use of a liquid C02-dry ice system on insulated wires and mixed nonferrous metallic concentrates.

Jan 1, 1973