Search Documents

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007

By B. W. Gandrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted, by the U, S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators On the basis of the float-and-sink data, an attempt has been made to determine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled, In the coal-producing districts of Alabama a great deaf of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 163 and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

By B. W. Candrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators on the basis of the float-and-sink data, an attempt has been made to deter-mine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled. In the coal-producing districts of Alabama a great deal of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 16B and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

By S. J. CRAIGHEAD

IN 1912 the United States Smelting Refining and Mining Company made a large investment in a number of coal properties in Utah and in 1915 a subsidiary, the United States Fuel Co., was organized to take over these properties. Operations started in 1916 and the Company soon became, and remains, one of the major coal producers of the State. It now produces approximately one million tons of coal annually, which is about 22 per cent of Utah's output. The U. S. Fuel Co. owns large reserves of good coal and is in a position to expand operations with the industrial growth now taking place in the West. Traveling through the Western States, one is struck by numerous advertising signs portraying the picture of jovial Old King Cole of nursery rhyme fame. His rotund figure and beaming countenance are the symbols of Utah King Coal, the product of the King mine of U. S. Fuel Co. King Coal is a by-word of quality coal throughout all the Western States.

Jan 1, 1948

By Larry D. Patts

Section 317(e) of the Federal Coal Mine Health & Safety Act of 1969 directed the Secretary of the Interior to prepare standards under which all working places in a mine shall be illuminated by permissible' lighting while persons are working in such places. Section 317(e) further provides that such Working places shall be illuminated within 18 months after such standards are promulgated. In accordance with this section of the Act, there was published in the Federal Register for December 31,1970 a notice of proposed ru1emaking which prescribed the illumination to be provided in the working p1 aces of underground coal mines. In 1ight of written comments, suggestions, and objections to this proposed ru1emaking, the proposed standards were with-drawn and reproposed in the Federal Register for Wednesday, October 27, 1971. In light of further comments, suggestions, and objections, a public hearing was held on April 4, 1974 and standards were again reproposed and published in the Federal Register for April 1, 1976. Promulgation of the final lighting standards took place on October 1, 1976 which means that the underground coal mining industry must comply with face illumination requirements by April 1, 1978. As mentioned previously, the first proposed ru1emaking for illumination of underground coal mines was published in the Federal Register on October 27, 1971. In early 1972, Consolidation Coal Company (Consol) and the United States Bureau of Mines agreed to a cooperative study of underground face illumination; Conso1 felt that expertise in this field would become increasingly important. Conso1's initial efforts in illumination were aimed at investigati.ng practical lighting systems for underground face equipment. We were concerned with installing unobtrusive lights which provided sufficient face illumination for safety, but at the same time were readily maintainable, electrically reliable, and physically sheltered from damage.

Jan 1, 1977

By A. L. Holley

This process is performed in the Pernot puddling furnace; it removes from 75 to 80 pel. cent. of the phosphorus, most of the sulphur, and practically all the silicon, from crude iron, in from five to eight minutes. It has been in regular use since March, 1877, and has produced over seventeen thousand tons of mashed metal for the openhearth furnace. During two years, nearly all, and lately, all the open-hearth steel produced in these works has been made from about 5 tons of washed pig and 2 tons of scrap per open-hearth furnace heat. There arc 12 open-hearth furnaces, of which 4 to 9 are running, according to the state of orders. A large amount of highly phosphoric iron from France and Belgium has been also washed and then puddled for parties who have taken, or are expected to take, licenses. The mashing of pig for puddling, however, is not a practice at Krupp's works, because pore pigs are nearly as cheap as impure ones. The author and his assistant, Mr. Laureau, spent, during the last month, three days at Krupp's works, examining this process. They copied out of the office books characteristic analyses and physical tests, some of which are given berewith. They also brought home many samples of pig, cleaned metal, puddle bar, and steel, which they saw treated. Analyses of some of these samples appear in Table IV. As there are no blast furnaces at Essen, the iron is melted in two Bessemer cupolas with fore-hearths; they melt 124 pounds of iron with 1 pound of coke. The metal is run by a spout from the forehearth into an opening at the side of the main door of the washingfurnace. The The washing-furnace.—This is a regenerative gas furnace. It has a Pernot revolving-hearth of 12 feet external diameter and 3 feet depth. (See Plate.) The four regenerator chambers hare 780 cubic feet capacity, which is about the same as the average regenerator capacity of open-hearth steel furnaces of equal tonnage. The lining is 13 inches thick on the sides and 9 inches on the bottom, thus giving a hearth 9 feet 10 inches by 2 feet 3 inches deep. The lining is composed of lumps of highly refractory ores

Jan 1, 1880

By P Micale

Geological data provides the foundations for the mining value chain. It is used to underpin the modelling and planning and consequently optimise downstream business decisions. However, it is often forgotten or taken for granted. End users often assume the data to be sound without verification. Geological data can be considered a company’s number one asset. Subsequently, the storage, use and management of this data need careful curation and time invested in preserving and protecting it. An established polymetallic mine with 20 000 drill holes could have a data replacement value in excess of $500M at 2020 prices, excluding labour and salary costs. The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the ‘JORC Code’) provides guidelines for Public Reporting. Within the code, Table 1 requires discussion around the different types of geological data, its collection and use. What is needed is additional details regarding the validation and integrity of the geological database. A comprehensive guideline specifying minimum geological standards for geological databases has been developed. This expands on the critical points outlined in Table 1 of the JORC Code. This guideline can be used by companies where geological databases are managed in-house or used to assess these services’ outsourcing. This guideline will ensure that geological data is reliable and unadulterated and can be used with confidence. Using this guideline will assist in preserving the investment of geological data in the mining value chain

Mar 22, 2022

By J. W. Town

This report summarizes the results of laboratory investigations conducted by the Federal Bureau of Mines to obtain hydrometallurgical information on the dissolution of mercury sulfides from ores, flotation concentrates, and pure mercuric sulfides. Statistical methods were used to design the experiments and evaluate the resulting data. Studies demonstrated that cinnabar is readily soluble in sodium sulfide, partly soluble in potassium sulfide, and essentially insoluble in ammonium sulfide. Additions of sodium hydroxide or potassium hydroxide to sodium sulfide solutions increased mercury extraction slightly; when either was added to potassium sulfide or ammonium sulfide solutions, mercury extraction was equal to that of sodium sulfide. Tests at the Albany Metallurgy Research Center showed that sodium sulfide would completely dissolve chemically pure mercuric sulfide, more than 95 percent of the cinnabar in 5-percent mercury flotation concentrates, and 60 to 90 percent of the cinnabar in low-grade ores. The double-leach tests showed that potassium sulfide would dissolve over 90 percent of the arsenic in mercury-arsenic products and 1 to 10 percent of the mercury; then sodium sulfide-hydroxide solutions would dissolve 80 to 90 percent of the remaining mercury and 5 to 10 percent of the arsenic.

Jan 1, 1961

By Marietta Canty

A paper is presented in which an innovative biological process is described for the treatment of cyanide-, metals-, and nitrate-contaminated mine process water. The technology was tested for its ability to detoxify cyanide and nitrate and immobilize metals in wastewater from agitation cyanide leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to demonstrate the technology on a mine process waste stream at a mine in Nevada. The demonstration was performed Jointly under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered by the U.S. Department of Energy's (DOE) Western Environmental Technology Office (WETO) and the Superfund Innovative Technology Evaluation (SITE) Demonstration Program under Interagency Agreement Number DW89938513-0 I-0. MSE Technology Applications, Inc. (MSE) located in Butte. Montana, was the contractor responsible for conducting the project, and Pintail Systems, Inc., of Aurora. Colorado, was the technology provider. The pilot-scale unit was field-tested at the Echo Bay McCoy/Cove Mine southwest of Battle Mountain, Nevada. The biotreatment process was considered to be successful in destroying cyanide in the mine process water. The process was also determined to be effective in removing metals. The pH was consistently neutralized, and nitrates were successfully removed from the mine process water. As a result of conducting these pilot-scale tests, the biotreatment process was concluded to be an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1998

By FREDERICW K. BRADLE

I HAVE been puzzled by two lines of thought'; one emanating from Washington, D. C., to the effect that we must all cheer up, that in a very short time, measured in terms of months, prices would begin to recover, business would become normal, and prosperity would continue on its way just as before the interruption of a year ago; and a second, coming from certain industrialists and economists, expressing fears that all commodity prices were in for a long downward trend, which would cause much unemployment, eventually drag down wages and so restrict purchasing power as to further aggravate the situation. One basis for the fear of a downward trend in commodity prices' is that ifter great wars a depression could last for something like 40 years-the downward trend to such a depression after our recent World War having been postponed for some reason or other; and the basis for another fear was that the production of gold was becoming less. I had 'also been trying for some time past to refresh my recollection as to how my ow11 particular lead interest climbed out of the depression of 1893; and as all the metals have had, and still have. relative values and prices, I can best express what I have in mind by talking principally about lead.

Jan 1, 1930

By John F. Martonik

When OSHA came into existence in 1970, it adopted national consensus standards to improve safety and health conditions in work places. Coke oven emissions, which are proven to cause cancer and respiratory diseases, were regulated by the coal tar pitch volatile standard, adopted from the 1969 edition of the Threshold Limit Values for Airborne Contaminants by the American Conference of Governmental Industrial Hygienists. The coal tar pitch standard, based upon the benzene soluble fraction of total particulates, limits the personal exposure to 200 micrograms of the benzene soluble fractions of total particulate per cubic meter of air. This standard can be classified as a performance standard because only general limits are set which allows the employer to choose for themselves the means to comply. Both the United Steelworkers of America and the American Iron and Steel Institute petitioned the Secretary of Labor to write a new standard for coke oven missions, each thinking the coal tar pitch standard unsatisfactory.

Jan 1, 1980

By V. Králová

The TESCAN Integrated Mineral Analyzer (TIMA), an automated mineralogy system, enables fast and quantitative mineral analyses of rocks, ores, concentrates, tailings, leach residues or smelter products. It combines BSE and EDX analysis for identification and measurement of mineral concentrations, particle size distribution, and liberation/locking parameters. In addition, it can provide bright particle searches for PGM, gold-silver ores, and/or REE. With the newly developed Automated Loading System (AutoLoader), the TIMA has become the world?s first automated mineral analyzer which permits robust, continuous and unattended sample loading. With the AutoLoader (robotics) system, the TIMA has emerged as a powerful plant support instrument. It increases the sample throughput, minimizes manual labor and enables 24/7 operations. As such, it can be used in daily, continuous mineralogy for mine geology/ore control, concentrators, leach operations, and smelter support. It will also increase the capabilities of technical service centers for mining companies, commercial laboratories, large drilling programs or pilot test campaigns. In combination with a highly automated sample preparation lab (sizing, potting and polishing), TIMA technology can establish high-throughput and fast-turnaround automated mineralogy lab modules for mine-site production support.

Feb 23, 2014

By Bisweswar Das, Barada Mishra, Hrushikesh Sahoo, Swagat Rath

Banded hematite jasper (BHJ) containing 45.2% Fe, 32.64% SiO2, 0.63 % Al2O3 and 1.25 % LOI is found difficult to beneficiate either by magnetic or flotation techniques due to fine intergrowth of jasper with hematite. Phase transformation by reduction roasting with activated charcoal followed by low intensity magnetic separation to achieve a suitable iron concentrate has been attempted in this study. The mineralogy of the ore and different roasted products has been studied by X-ray powder diffraction (XRD) and scanning electron microscope (SEM) to understand the reduction mechanism. The magnetite formation is observed at 850ºC while metallic iron appeared at a higher temperature. The effects of reduction variables such as reduction time (30-270 min), temperature (750-1050ºC), and reductant (1-12 %) using activated charcoal are studied. An iron concentrate with 64.65% Fe and 55.8% recovery could be obtained under optimum conditions of temperature: 850ºC, time: 1.5 h, and reductant: 6% by weight.

Jan 1, 2014

By H. A. Thorne

This paper describing the mining practices at the Chino mines at Santa Rita, Grant County, N. Mex., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Nevada Consolidated Copper Co., Chino mine's, operates an open-cut copper mine at Santa Rita, Central mining district, Grant County, N. Mex. This mine is located about 16 miles east and slightly north of Silver City, the county seat. The ore is-transported in standard railroad cars by the Atchison, Topeka & Santa Fe Railway Co., approximately 10 miles to Hurley where it is milled. The concentrated are shipped approximately l'70 miles over the same railroad to the smelter of the American Smelting and Refining Co., at El Paso, Tex. (fig. 1)

Jan 1, 1931

By Chas. H. Behre

MINING geology, both theoretical and practical, continued to make noteworthy progress during 1938. Mining companies generally, stimulated especially by the improvement in economic conditions during the latter part of the year, extended their workings and developed new ore bodies. Federal and state surveys expanded their search for favorable localities and actual ore bodies, with corresponding enlargement of regional knowledge. Theoretical investigations covered geochemistry of ore deposition, structural control of mineralization, and mineralogy of the ores (chiefly aided by the microscope). More geochemical work is greatly needed: ore searching is still too purely empirical, based on features that have been recognized else- where. Thus, clearer understanding of the conditions essential to transportation of metal salts is needed. Jean Verhogen has suggested that solubilities

Jan 1, 1939

By Y. K. Rao

In the carbonyl process for the refining of crude nickel CO(g) reacts with nickel in the 310-370K range producing nickel tetracarbonyl, Ni(C0)4(g). Iron and cobalt impurities also form gaseous carbonyls but their partial pressures are low. The carbonyl is led to a decomposer plant wherein the gas disproportionates in the 500-600K range depositing pure metal on nickel pellets that move countercurrent to the gas-flow. This system serves to illustrate the fundamental principles involved in the vapor phase mass transport of elements, against temperature-gradient, under the influence of chemical potential gradient. Unlike in the crystal growth, the source is at a lower temperature (say 350K) whereas the seed is in the hot-zone (say 550K) of the closed ampoule-type reactor. By assuming virtual gas-solid equilibria in the end zones, with diffusion of gaseous species between them acting as a slight perturbation, the quasi-steady- state mass-transport rates are computed for a range of CO-pressures and temperatures.

Jan 1, 1993

By John Ward Smith

Variations in specific gravity of oil retorted from oil shales of the Eocene Green River Formation in northwestern Colorado were evaluated statistically, demonstrating that these variations are very strongly associated with stratigraphic position and less strongly but still significantly associated with geographic location. Specific gravity of oil retorted from these oil shales apparently varies with the carboxyl group content of the oil shale's organic matter. Higher temperatures accompanying increasing depth of burial probably progressively decarboxylated oil shale's organic matter producing the decrease of oil specific gravity associated with deeper stratigraphic position. The geographically associated oil-gravity variations were probably produced by regional variation in the original thickness of late Cenozoic extrusive rocks once overlying the Green River Formation.

Jan 1, 1966

By Roger J. Morrell

Disk-cutter experiments were performed on five rock types ranging in compressive strength from 9,000 psi to 27,000 psi. A specially constructed testing machine called a linear-cutter apparatus (LCA) was designed to load and traverse a free-rolling disk cutter across a sawed rock surface. The LCA was instrumented to measure the vertical and horizontal forces acting on the cutter during the run.. The ability of disk cutters to fragment rock was determined for both 60--degree and 90-degree cutting-edge angles, and relationships and regression equations were developed to predict cutter performance based on rock physical properties and applied forces,

Jan 1, 1970

The Grootegeluk coal beneficiation plant is situated near Ellisras in the Waterberg coal= field in the Transvaal, RSA. At this plant 15 million tons of coal bearing material per annum are beneficiated by means of two-stage heavy medium bath and cyclone plants. Because of the very low yield of 12 % coking coal product, run= ping costs are of the - utmost importance. For this reason extensive tests were carried out to establish the most effective crushing and bene= ficiation methods and suitable aquipment. At the second heavy medium separation stage, the near-gravity material (+ 0,1. g/cc) amounts to 45 % and daily plant performance ana=lysis is required to ensure acceptable plant efficiency. Beneficiation processes for the -0,5 mm coal originally considered were froth flotation, shaking tables, heavy medium cyclones and water- only cyclones. When the froth flotation route was decided upon, further test work was done to enable selection of the equipment most suitable for the particular requirements.

Jan 1, 1987

By P. D. Nolan

Smelters operating under pollution control orders have become increasingly dependent upon the reliable operation of sulphuric acid plants and no factor affects the long term reliability of those plants more than efficient gas cleaning. The sources and characteristics of contaminants in smelter of fgases and the conventional approaches to removing these contaminants to accepted levels are discussed. New technology is described which offers advantages of lower capital cost, lower operating cost and reduced space requirements over the conventional approaches. This new technology has been developed by LAB s.a. and is licensed for metallurgical gas applications by Chemetics International Company.

Jan 1, 1983