Search Documents

By Takashi Miyamoto, Hideo Nakae, Hideki Yamaura, Takeshi Yanagihara

"For the production of partially composed metal matrix composites, namely discontinuous MMCs, using a casting· process, the interpenetrated phase composites with SiC particles were fabricated by pressureless iDfiltration using molten Al-Si alloys. This process is based on a wetting phenomenon, therefore, we discussed the technique based on the reactive wetting. The SiC particles coated by diluted water glass were sintered in a mullite Tammann tube and simultaneously infiltrated with molten Al-Si alloys in air at 1173~1573K. As for the improvement of the wettability between the SiC and the liquid aluminum alloy, Fe3O 4 powder was mixed with the water glass due to the thermit reaction between Fe3O4 and molten aluminum alloy. In some experiments, pure aluminum powder was placed on the sintered SiC to increase the interfacial area and the chemical reaction between the sintered Sic. and the melt. By combining these conditions, we succeeded in the complete infiltration without pressure at 1173K.IntroductionAs is well known, the mechanical properties of metal matrix composites (abbreviated MMCs) are superior than that of ordinary metals. However, their use has not been widely accepted because the production cost is very high due to their poor machinability. Therefore, the production of partially composed, namely discontinuous MMCs, by as the Lanxide process [l,2] has been investigated for many years. The Lanxide process, it takes a long time, sometimes up to 10h, in a nitrogen atmosphere for the infiltration. Therefore, the cost will be higher for common use. On the other hand, a high 'pressure process has been adopted for the production of discontinuous MMCs by the Toyota Motor Corp.[3]."

Jan 1, 2000

Maximizing margins in competitive markets demands superior productivity. Unfortunately, management systems developed early this century for other industries often drive counterproductive behaviors choking mining productivity. Many executives and managers waste valuable time and effort relying on simply training and communicating to improve managerial practices and attitudes. In covering practical human behaviour, the paper explains why this fails -and explains how to use systems to successfully drive improved managerial practices and attitudes. It highlights use of modern performance Measurement, Analysis and Reporting systems to drive behaviors and improve margins -without capital investment -and make executive and managerial work easier and more effective.

Jan 1, 1999

By G Tranell, E Pastor-Vallés, A Vallejo-Olivares, J B. Pettersen

Metals are essential for the sustainability transition and decarbonisation of society. Yet, it will be paramount to produce them sustainably and minimise the affiliated resource and energy use and the associated emissions. In the circular economy, the metallurgical industry should recycle existing material stocks, and improve its utilisation of wastes, residues and side streams. This increases the complexity of processes, as they become both (often multi-fraction) waste treatment as well as material production processes and brings complexity to the assessment of environmental benefits. Assessing the environmental impact of technological developments frequently is supported by life cycle assessment (LCA). While the method is well documented, its implementation involves several methodological choices that deserve reasoning and analysis, such as how to define the product when former wastes are turned into new products, the selection of impact methodology when converting emissions to environmental indicators, the definition of system boundaries and co-product allocation and the interpretation of sensitivity and uncertainty in final outcomes. In this exploratory study, we investigate how the variation of LCA set-up affects the environmental burden of the system. We consider a metallurgical process where a mix of hard-to-recycle aluminium-containing streams is used to produce aluminium cast alloys in a rotary furnace. Remelting with salt-fluxes allows recovering metals from partly oxidised/contaminated streams, such as dross, bottom ash and industrial shavings, but at the expense of generating significant amounts of salt-slag/salt-cake hazardous waste. The study considers different system alternatives such as landfilling the salt-slag residues versus valourising them into salts, aluminium concentrates, ammonium sulfate and non-metallic-compounds to be used by the metallurgical, construction or chemical industries. Practical recommendations are outlined to facilitate the implementation of LCA in assessing the potential benefits of the circular economy in the metallurgical sector.

Aug 21, 2024

By A. L. Hornbaker

Colorado has recorded more than 100 years of industrial mineral production. Much of the state's history, culture, and economy is based in mining, but the industrial minerals and construction materials comprising the nonmetallics sector of the industry very often are overlooked or overshadowed by mineral fuels and the metals. Indeed, many of these materials find use in seemingly unimportant industrial applications essential to our economy and life style and yet are not so recognized by the consumer. Unlike many other mineral resources, the numerous industrial minerals occur in many different and often exotic geologic environments, some of which are characteristic only of the western states. In Colorado only a few of these minerals have continued production through the years; many saw only "boom" periods or other critical times of need, such as the world wars. The changing needs and demands of our society in the 1980s will stimulate yet another era of intensive activity in our industrial minerals storehouse. Researchers are finding new uses and applications for these materials in dealing with the energy crisis and fuel shortages, the need to develop domestic mineral reserves of all kinds, and the goals of reuse and recycling. Some of Colorado's little-used and unused industrial minerals hold extraordinary promise in solving some of these problems on the regional and national levels. In this paper we will look at the history of development of Colorado's more prominent nonmetallics and especially at current research on and future potential of several other commodities among which Colorado contains the largest known reserves.

Jan 1, 1980

By R. K. Dwari

The electrostatic beneficiation of coal is based on tribocharging characteristics of ash forming minerals and coal particles. The tribocharging of quartz, pyrite and coal particles contacted with various metals and polymeric materials have been measured and the charge acquisition is assessed through surface energy calculations from liquid contact angle data. The contact angles, before and after tribocharging of solids, are measured using Krüss tensiometer and Washburn?s method where the sample holders in tensiometer are specially constructed with tribocharger materials. The charge polarity and amount of charge acquired by quartz, pyrite and carbon with metal tribochargers were found in good agreement with the reported work functions of the contacting surfaces. The charge results with polymer materials differed from the work function values, presumably caused by surface contamination. The surface energy of quartz calculated by all the theoretical approaches in the literature showed that the tribocharging increases the surface energy. Both polar and non-polar components computed from Fowkes and Owens-Wendt-Rabel-Kaelble approaches dis-play that both these components increased after triboelectrification. However, the polar component divided into acid and base components, as in van Oss approach, manifest decreasing acid part and increasing base part. Since quartz charged negatively during tribocharging with metal surfaces and therefore accepted electrons, the determined acid and base surface energy components are consistent with charge transfer process. The results also elucidate an explicit correlation between the charges generated by powders and the surface acceptor (acid) and donor (base) electronic states and thereby the work functions. A novel fluidized bed tribocharger was designed and developed with internal baffle system for efficient contact electrification of mineral and maceral to produce high differential charging for efficient separation. The results achieved on coal with 45% ash content are presented and discussed.

Jan 1, 2014

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By W. M. McKewan

This U.S. Bureau of Mines report discusses wire ropes used for hoisting in U.S. mines. The in-formation presented was extracted from a large body of data compiled by the U.S. Mine Safety and Health Administration (MSHA) using a data base management system (DMS). Further, these extracted data were then manipulated to provide tables of data that show the types and amount of wire rope used for hoisting. This report describes the different types of wire ropes and how a DMS can be used to manipulate MSHA's wire rope inventory data. The data indicate that more 1-1/4-in-diam ropes, 6x27 construction ropes, and right lang lay ropes are used in U.S. mines than ropes of any other diameter, construction, or lay type.

Jan 1, 1991

By Robert E. Sorenson

EXPLORATION for deep-seated orebodies in the Silver Belt area of the Coeur d'Alene mining district is complicated by meager surface expressions of diagnostic criteria, lack of knowledge of the significance of specific alteration phenomena, and the great expense involved in the exploration for ore shoots, the tops of which often occur near sea level elevation or below and as much as 4000 ft or more below the surface. Except for the early studies of Ransome and Calkins in 1903 and 1904,[1] little geological work was done in the Coeur d'Alene district for many years, and it is only during the last 15 to 20 years that complete and careful geological mapping has been applied to most of the mines in the area. Much early information, which now would prove invaluable, is lost in hundreds of miles of caved and inaccessible mine openings not mapped by mining geologists. In more recent years mining geology has become a tool of greater use in the district, and some measurable progress is being made in the accumulation of observations that are adding gradually to the knowledge of ore deposits in the district.

Jan 7, 1951

By A. L. Engel

STRICTLY speaking, ore-dressing does not commence until after the ore is in the mill bins, but where complex ores are treated and their minerals separated to make the best commercial concentrate with the lowest economical tailing, ore-dressing problems begin and often center in the mine itself. This does not refer to the grade of the ore, but rather to the frequent condition in which metallurgical results radically different from customary are obtained because of changes in the character of the ore treated. Different varieties of ore can usually be identified as coming from well-defined depths or zones in the mine, or from known sections of the orebody. Varying degrees of alteration of the ore, inclusions of harmful gangue material, or variations in the quantities of component metallic minerals are often causes of temporarily bad metallurgical results in otherwise successfully operated plants, especially those employing differential flotation to. recover several valuable minerals contained in the ore.

Jan 1, 1931

Adequate ventilation of coal mine working faces is the single most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. Bureau research has shown that to control respirable dust you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane the most effective approach has been to use a blowing brattice or tubing and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present, Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan-powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray fan controls methane on exhaust-ventilated sections.

Jan 1, 1988

By J. D. Stewart

One of the first important questions that should be settled on the opening of a mine or the development of a new deep is the system of haulage to be used, since the layout of the haulage-ways at the pit bottom, or, in case of a slope mine, the arrangement of the surface works, depends largely upon the type selected. Should it later become desirable to install a system of haulage of a type other than that for which the mine roadways were originally laid out, considerable difficulty would likely be encountered in its installation and with the result that it would in all probability be most unsatisfactory and expensive in its operations. It therefore becomes very necessary that full consideration be given the haulage problem at an early date in order that the type best suited to the mine conditions and the required outputs can be intelligently planned for. It is sometimes found, however, that no matter how well the mining engineer explores the seam to be developed, or how accurately he anticipates its eccentricities, there will still remain some unrevealed or unsuspected conditions, or shall we say obstacles, placed by Nature to prevent the too easy winning of her treasures and incidentally to frustrate or modify the application of the plan so painstakingly laid down on paper, and to adversely affect the cost estimate.

Jan 1, 1928

By Peter Middendorp, David J. Tara, Gerald E. Verbeek, Jan Fischer

"For pile driving simulation the model used must be accurate for the entire process, i.e. from the start of pile driving until the pile has reached its target depth. Of the various model components (hammer, pile and soil), the soil is the most difficult to characterize accurately. This is well known, but the aspect that is not as well understood (and therefore commonly misapplied) is the fact that the soil properties and thus the soil parameters do not remain constant during the pile driving process. Furthermore, this phenomenon of soil fatigue, mainly for skin friction, as a continual change of soil resistance during pile installation, is not implemented into all commonly applied pile driving simulation software and could therefore not be taken into consideration. In this paper the effect of soil fatigue will be described by numerous research results, showing that this effect will occur regardless. Different methods to consider the change of soil resistance during pile installation will be presented, some applying soil fatigue while others merely reduce soil resistances. Using currently available wave equation software that can take soil fatigue into consideration, the importance of doing so will be shown on the basis of the back calculation of a monopile installed offshore in Germany.THEORY BEHIND SOIL FATIGUESkin friction and toe resistanceTo simulate pile installation as accurately as possible, detailed geotechnical knowledge about the mechanical behavior of the soil surrounding the pile is necessary during each step of the installation process. Therefore, to ensure ""geo-mechanical correctness"" of a pile driving simulation, the shaft friction and the toe resistance have to be recalculated at each penetration level. For the skin friction parameters this is especially important since they change significantly during pile installation because of soil fatigue. Depending on the pile and soil type, the toe resistance can experience changes as well due to soil fatigue during to pile driving. However, in this paper the toe resistance values were kept constant over the entire penetration depth.In general, the unit skin friction can be derived from measured values (CPT, qs) or calculated as a function of the horizontal effective stresses dh acting perpendicular to the pile wall of a vertically driven pile. The horizontal stresses can then be converted into the unit skin friction qs using the Mohr-Coulomb failure criterion:"

Jan 1, 2017

By Harold J. Barnett

In January 1948 , the Secretary of the Interior directed that a study be made of energy resources and requirements that would provide a basis for continuing appraisal of the adequacy of the Department's programs in the energy field . That this instruction was timely has been demonstrated by the increasing interest being evidenced by Congress , industry , labor , and the public in the future of the energy segment of our national economy . Several studies of individual energy sectors have appeared . Various legislative proposals have been made in Congress for obtaining more information on this subject . Substantial interest in energy projections is not , of course , a recent innovation . Energy availability and consumption are strategic factors in peacetime prosperity and growth and in our national defense as well . The past generation's literature of earnest public discussion and of legislative consideration of matters involving energy projections is very extensive . This is an exploratory study produced in the Program Staff of the Office of the Secretary of the Interior in the first half of 1949 and revised recently to take account of certain of the preliminary energy data from the 1947 Census of Manufactures and critical comments . It is offered at this time solely as a technical contribution in economic research technique . As the Bureau of Mines has recently undertaken to revise this preliminary study , critical and other comments are invited .

Oct 1, 1950

By D J. Williams

The majority of surface tailings storage facilities continue to employ sub-aerial tailings slurry deposition. Surface TSFs are typically sized and operated in a way to minimise the initial capital cost of the facility, driven largely by the net present value approach to accounting. This generally leads to too small a storage, too fast a rate of rise of the tailings, and difficulties in managing supernatant water. In turn, this results in wet and soft tailings deposits of high moisture content and low density, and the need for frequent and costly tailings dam raises. Further, such tailings deposits often do not facilitate closure and rehabilitation of the facility. Globally, there are on average over two failures annually of such tailings dams, resulting in loss of life, damage to infrastructure and environmental impact downstream, and the loss of company shareholder value and reputation. Recent high profile tailings dam failures are threatening the mining industry’s financial and social licence to operate.Among the physical processes that tailings undergo on sub-aerial deposition are beaching, hydraulic sorting down the beach according to particle size and specific gravity, settling, consolidation, and desiccation on exposure to the sun and wind. Beaching and hydraulic sorting have proved difficult to test at laboratory scale and difficult to model, and are best assessed in the field. Settling, consolidation and desiccation may be assessed at laboratory scale, but to date there has been an absence of tests to form the basis for the design and management of tailings deposition, and ultimate closure and rehabilitation. The paper describes recent advances in tailings testing methods, including a purpose-built slurry consolidometer that tests the settling and consolidation of tailings from a slurry consistency, simulating increasing tailings depth to about 50 m; and a purpose-built instrumented column that tests the settling, self-weight consolidation and desiccation of a surface layer of tailings, also from a slurry consistency. Selected test results from these two apparatus are presented in the paper, together with brief descriptions of how they may be used to better design tailings slurry deposition. In addition, planned further advances in tailings testing methods are briefly described.CITATION:Williams, D J, 2018. Recent advances in tailings testing methods, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 8–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By M. Mahan, D. D. Blue, O. C. Garst, F. Fraas, L. Fink

"Early in World War II it became apparent that the known bauxite re- serves might not be adequate to supply the demands of the American aluminum-producing industry, as the transportation of bauxite from abroad to this country might easily be interfered with by hostile action. Consequently, the Bureau of Mines set up an intensive, well-integrated program for the production of cell-grade alumina from low-grade domestic ores. This pro-gram of investigation covered the production of alumina from clay, alumite, red mud, and other low- and marginal-grade ores. In line with the Bureau's usual policy of conservation of natural resources, it was decided that the investigation should be extended to cover the production of alumina and other valuable byproducts from aluminum dross.Statistical information showed that during the year 1943-44, an average of 2,900 tons of aluminum dross was generated monthly. This dross, after partial removal of free metal, had an average metallic aluminum content of approximately 9 percent. Some of this dross was produced by the melting of alloyed aluminum; but a large proportion 1,700 out of 2,900 tons - was generated by two producers of primary aluminum, and the dross did not contain an great proportion of alloying metals. Compared with dross from other sources, this 60 percent of the country's capacity can be assumed to have relatively uniform composition. Moreovcr, the problem of collection and distribution can be minimized because of the relatively small number of plants included in the organization of these two producers of virgin metal.Except for large pieces of metallic aluminum that easily can be mechanically separated for remelting, this dross has been discarded and scrapped. Inasmuch as chemical analyses show that the alumina content of dross is far higher-than ordinary ores - 111 percent alumina equivalent in dross compared to 57 percent alumina in bauxite - aluminum dross is a far richer source of aluminum than any known naturally occurring ores. The discard, of this waste material during the war and reconversion periods would be unsound economically. The work reported herein describes tests at the College Park Station of the Bureau of Mines on the recovery of metal, alumina, ammonia, methane, and abrasive-grade corundum from dross."

May 1, 1946

By K. S. Raja, F. Battick, B. Pesic

"CeO2 doped with lower valence cations, such as Y3+, Sm3+, Gd3+ etc. is considered as electrolyte material for low temperature SOFC. Doping introduces additional oxygen vacancies and improves ionic conductivity. This work describes the preparation of yttria-calcia doped-ceria precursor material, its sintering in DC and AC field methods, and characterization of sintered electrolytes with respect to the ionic conductivity. Doped precursor materials were prepared by a controlled co-precipitation process. Sintering of prepared, pelletized particulates was carried out using three different methods such as: 1) conventional; 2) spark plasma sintering; and 3) an alternating current field at 1125°C (AC assisted sintering). The mechanism involved in the conductivity improvement as a function of defect density, grain boundary area and phase stability will be discussed. INTRODUCTIONThe performance of SOFCs depends highly on the properties of materials. Subtle variations in the composition, microstructure, or density of SOFC components can considerably alter the power output capabilities of fuel cells. Early SOFCs utilized zirconia based electrolytes but efforts in lowering the operating temperatures of SOFCs have prompted investigations into several other oxygen ion conductors – often modified with dopants to either promote the formation of oxygen vacancies or to stabilize a vacancy rich high temperature phase – such as bismuth oxide, lanthanum gallate, and ceria.The transport of oxygen ions through the electrolyte first begins with diffusion into the material. While this is generally a surface kinetics phenomenon, it is safe to say that it is highly dependent on oxygen pressure and vacancy gradients. The role of the cathode in SOFCs is to reduce oxygen at the electrolyte surface creating an O2– ion gradient which induces permeation into the material. Once inside and under the influence of a potential field, O2– ions migrate by a vacancy hopping mechanism, Catlow, C.R.A. (1990), effectively exchanging positions throughout the matrix until they reach the anode and react, thus leaving the matrix."

Jan 1, 2012

By V. A. Ettel

Current practices in electrolytic winning and refining of copper , nickel and zinc are reviewed from the point of view of their respective energy requirements. The electrical energy requirements of these processes are broken down in to the individual components, which belong to two basic categories: (a) thermodynamic energy requirements (G of the desired reaction) : (b) energy losses (anode and cathode polarizations, ohmic drops in the electrolyte and in the cell hardware, energy losses due to unwanted side reactions and electrical shorts). The individual energy components are separately examined for each electrolytic process and the potential for energy saving in these processes is discussed. It is shown that many potential energy-saving measures are uneconomical at the present time, as they increase over-all operating costs. The discussion is focused on those approaches which hold most promise for the future.

Jan 1, 1977

By R. C. A. Thurston

Introduction A mechanical spring has been .defined by Wahl ( 1) as 'an elastic body whose ?primary function is? to deflect or distort under load, and which recovers its original shape when released after being distorted'. Most material bodies are elastic to some extent ? and will deform under load, but they are seldom regarded as springs since this is not their primary function. The principal applications of springs are the absorption of energy and the mitigation of shock, the support cf moving masses or the isolation of vibration, and the provision or measurement of definite loads or torques. A large number of spring types have been developed to serve these purposes and to meet the different operational requirements; they range from the large semi-elliptic leaf suspension spring to the delicate watch hairspring. The springs of most importance in machine design, however, are the helical round-wire compression or tension types. They are made in a wide variety of sizes and are used in tremendous quantities, mainly because of their low cost, their compactness, and their relatively high efficiency. Their field of application is as broad as that of machine design itself, but the bulk of production is almost certainly for suspension systems of vehicles such as automobiles, freight and passenger cars, and mine cars, and it is with the last of these applications that this paper is primarily concerned.

Jan 1, 1951

By John J. Mulligan

Coalbeds were discovered in outcroppings of the Beacon group of sediments on the north end of the Willett Range ( altitude 77 ° 11 ' S , longitude 160 ° 20 ' E ) , Victoria Land , Antarctica , in December 1960 during an investigation undertaken as part of the U.S. Antarctic Research Program under the auspices of the National Science Foundation . Three separate exposures of coal or coaly material were found . Two of the exposures contain , respectively , eight and four beds of hard , compact , finely banded attrital coal ranging in thickness from 8 feet downward to a few inches , and reported to range in rank from mediumvolatile bituminous to semianthracite . The coals are associated with carbonaceous shales containing an abundant assemblage of fossil plants resembling those associated with the Permian coals of Australia and other Gondwana areas . The third exposure , apparently somewhat higher in the stratigraphic sequence , contains only coaly plant fragments scattered through a thin conglomerate and overlying sandstones . A sandstone bed that overlies these coal - bearing sandstones contains abundant logs and fragments of silicified wood . Preservation of features is poor , but one segment of a silicified stem suggests comparison with Rhexoxylon , a gymnospermous tree that usually is considered indicative of Triassic age . The Beacon sediments in this area have been invaded , broken , and uplifted by a massive series of diabase sills and dikes greater in volume than the intruded sediments . The heat emitted by these intrusives must have advanced the metamorphic development of the coals . However , there is no evidence of alteration to graphite , and coal found in direct contact with a diabase sill contains no vesicles or other usual evidences of natural coking . Either the pressure of overlying rocks inhibited the development of coke , or the coals had been metamorphosed beyond the coke forming stage before the igneous intrusion .

Jan 1, 1963

By V. V. Musaev, A. M. Klyushnikov, R. R. Galimov

"A study was made of chemical and material compositions of the oxidized gold-bearing ore of the Kochkovskoe deposit. It was demonstrated that examined ore consisted mainly of quartz, carbonate and feldspar with a gold content of 2.2 g/t and a silver content of 6.1 g/t. By means of agitation leaching tests it was founded that about 79-80 % of gold can be extracted from ore using cyanide leaching solutions. The achieved high-speed dissolution rate of gold was due to its presence in a finely dispersed state (less than 2.73 µm), which was confirmed by the research of Uralmekhanobr. It was proposed that the ore can be processed by heap leaching process using cyanide leach solutions. Technological studies on the modeling of the heap leaching process were initially carried out in percolators with a capacity of 5 kg on agglomerated ore. It was preliminary established that agglomeration should be carried out at a cement consumption of 12-16 kg/t, with the moisture content in pellets reaching up to 10-12 %. The best percolation leaching results can be obtained with ore crushed to the size of -20 mm. The maximum extraction of gold to the solution was 79-80 % while the L:S ratio reached 1.2-1.4:1.In cooperation with the research center of OJSC ""Berezovsky mine"" a semi-industrial heap leaching test was accomplished. The result of a test performed was an extraction of 78.5 % of Au and 21 % of Ag from ore to a pregnant solution. This extraction degree was achieved at a L:S ratio 0.9: 1. On the ground of results obtained, a technical regulation was developed for design of the heap leaching plant with the capacity of 500 thousand tons of ore per year.INTRODUCTION The ore of the Kochkovskoe deposit represents an important reserve of gold in the Zabaikal region. Of the upmost interest are oxidized ores, the processing of which can be carried out by heap leaching (HL) with cyanide solutions. The purpose of this work was to study the composition and to develop a technology for heap leaching of oxidized ore."

Jan 1, 2018