Search Documents

By Brad Simser

Several case histories from Glencore’s Sudbury Operations show how passive seismic monitoring data is used for geotechnical decision making. The data comes from three different seismic arrays monitoring two open stoping deposits, and a narrow vein cut and fill/blasthole operation. Mining depths range between 1000 to 1680m below surface. The deposits are hosted in hard igneous rocks typical of the Sudbury basin, with characteristically high horizontal stress (approximately 1.8 times the depth of overburden). Rockbursting is the main geotechnical risk, due to the strong brittle nature of the rock and local high mining extraction. Fault related seismicity includes both fault slip events, and the stress channelling effect as the mining front approaches a major fault structure. Planar data trends generally line up with known faults and often indicate early stage fault activation. The structures are risk ranked based on their seismic response. This has been particularly useful at the Nickel Rim South Mine (NRS) where the structural fabric (jointing and small-scale faulting) is generally parallel to the more through going faults. The persistence of structures is difficult to measure, and the NRS faults generally have low offsets and thin gouge. The visual difference between the more persistent structures that occasionally generate large seismic events (up Mw 2.9 to date) and localised joints/slips is often minor. The seismic monitoring data clearly shows the more active structures. This information is highlighted on mine plans to help guide enhanced ground support and seismic re-entry protocol barricade locations. Pillar loading/yielding is a key element to the blasthole operations where a primary/secondary mining sequence is used. The secondary pillars are mined in a yielded state with just-in-time development. An example of the seismic signature of a secondary stope is shown with emphasis on the need for high location accuracy given the stope widths of 12.5 to 15m. The ratio of the shear wave energy to primary wave energy (Es/Ep) has long been used as a method to estimate source mechanisms; the higher the ratio, the more likely the event is fault slip versus rock fracturing. Data sets are filtered on Es/Ep ratios to highlight both fault slip populations and stress fracturing mechanisms. Examples of seismic data quality checks, high stress development, and re-entry protocols are also shown in the case histories.

Apr 26, 2022

This paper deals with the evolution of Canadian shaft sinking technology over the last 15 years. Most, if not all, shaft excavation projects in Canada prior to 1990 were sunk using traditional benching methods with labour intensive equipment. In the late-1980s, J S Redpath Limited of North Bay, Ontario, Canada, were contracted to deepen the shaft at Atomic Energy of Canada LimitedÆs Underground Research Laboratory (URL) located in southern Manitoba. The laboratoryÆs role was underground hydrological and geomechanical research, so the project offered both time and opportunity to conduct additional experiments while sinking. The offshoot of the research program was the true birth of the Canadian version of full-face, long round shaft sinking technology. Throughout the 1990s, this sinking method has been further refined over a number of shafts. The results have been faster sinking rates, a safer work environment and an overall improvement in project economics.

Jan 1, 2002

By Henry M. Howe

THE death of Sir Lowthian Bell removes almost the last of the group of heroic leaders who made their age and ours the Age of Steel-a group which his luster and the luster of his peers, Bessemer, Siemens and Tunner, made one of the most brilliant, perhaps even the most brilliant, in the annals of industry. Born on February 15th, 1816, in Newcastle-on-Tyne, he was the eldest son of Thomas Bell, an alderman of Newcastle, and of his wife Catherine Lowthian of Newbiggin, near Carlisle, in Cumberland, and was christened Isaac Lowthian, the name of his maternal grandfather. His father was born about 1788, and came in 1808 from Newbiggin to Newcastle, where he entered the office of the Cumbrian firm of Losh and Company, manufacturers of alkali and wrought-iron, at the Walker Iron and Alkali Works, at Walker, Dear Newcastle. Young Isaac Lowthian Bell was educated at Dr. Bruce's school in Newcastle, whence he went to Germany and Denmark, learning there German and Danish. On his return he studied at Edinburgh University, and then at the Sorboune in Paris. As a student he already showed the remarkable character and application which later gained him such distinction. After studying the manufacture of alkali near Marseilles, he returned, and when about twenty years old (A.D. 1836) was employed in his father's firm, then called Losh, Wilson, and Bell. After spending a year in their Newcastle offices, and after visiting the important iron-making districts of France, Germany, Poland, and Austria, he took charge of their rolling-mills at Walker, and profited so well by his opportunities, and especially by the teachings of his father and of Mr. John Vaughan (later one of the founders of the great firm of Bolckow, Vaughan & Co.), that he was made manager of the Walker works in or about

Sep 1, 1905

This presentation addresses the sources and weighting of project risk in coarse gold deposits with relevance to experiences at the Ballarat mine and Castlemaine goldfield. With sample representation and reliability often a source of great error in the resource estimation of coarse gold deposits, it follows that this matter should be of greatest risk to a mining project - but is it? What are the costs and efforts required to best quantify the sampling error due to nuggetty effect? After all, the main problem in Victorian gold mining ventures in the current decade is not the amount of gold available, but defi ning which portion of it can be converted to Ore Reserves or more so profitable gold bars. The author postulates that greater risk to the project lies in the geological interpretation and matching resource spatial parameters to mining methods, than the degree of uncertainty related to grade due to nuggetty gold. Recent experience in the Victorian goldfi elds is that the investor market has already severely discounted Mineral Resources reported in accordance with The JORC Code - so if they don't believe in the capacity to upgrade the resource why should we? To this end, Castlemaine Goldfi elds Ltd at its Ballarat gold project does not intend to estimate its gold mineralisation for public release, instead choosing to focus on the geological interpretation and mine planning elements. So with coarse gold deposits, is your Mineral Resource reported with The JORC Code a glass half full or half empty? Our mining forefathers in Victoria had no predictive tools which could define resources to any degree and yet were successful. By over emphasis on the definition of mineral resources and particularly the sampling error, are we ignoring the basics of cost control, solid geological interpretations and maximum mining flexibility. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By Amr Sallam, Ahmad Mohamed, Mohamed Alrowaimi

Renewable energy, in the form of wind and solar, has emerged as main source of energy in the modern society. The wind industry has substantially grown over the last two decades to become a key player in providing energy to public. Wind turbines are getting larger, taller, and more efficient every year. The foundation is a major component of the wind turbine system. The wind turbine foundation must provide short and long-term stability for the overall turbine to allow continuous and safe turbine operation for energy production. The turbine serviceability and stability requirements must be geotechnically and structurally satisfied. In North America, major foundation types currently utilized in the wind industry include gravity spread foundation, mono pier foundation, and pile foundation. In this case study, a Post Tensioned Pile Cap (PTPC) foundation was used to support a 3.15-3.4 Megawatt turbine with 125M Rotor supported on 87.5M-hub-height tower. Soil anchors in the form of Auger-Pressure-Grouted-Displacement (APGD) piles and Continuous Flight Auger (CFA) piles were utilized. Four distinct subsoil conditions were identified, and for which four pile designs were adapted. Due to the occasional encounter of stronger soils at 50 to 55 feet (15.2 to 16.7 m), shorter pile design was preferred. To satisfy the design uplift load, pile post grouting were utilized to increase the shaft capacity of the piles. In this paper, the pre-production pile load test program will be described. The pile load test procedure, analysis, and results will be presented. A discussion will be provided, which led to the selection of the optimum pile design to support the high tension loads taking into consideration pile length limitations.

By Hamid Maleki

This paper reviews a study conducted for Australian Coal Research Limited (ACARP) to assist Anglo-American operations with better understanding of coal burst mechanics and control based on U.S. practical experience, investigations, and inspections in three major U.S. coalfields over the past 45 years. The study examined both nonviolent and burst-prone case studies to identify contributing risk factors and addressed failure mechanisms for major U.S. coalfields in Utah, Colorado, and Kentucky, which have diverse characteristics. To investigate the mechanics of coal burst, a multipronged approach is used. First, field measurements in three mines from East Mountain, Utah, are complemented with finite-difference stress analyses to address the importance of horizontal stress in coal pillar mechanics of violent failure. Second, the computational procedures for estimating seismicity resulting from slip along geological discontinuities are reviewed, as these measurements point to seismicity being the trigger mechanism for violent failure of marginally stable structures. This joint-slip seismicity mechanism is in agreement with the more recentimproved re-examination of mining-induced seismicity (MIS) data from the Crandall Canyon Mine, Utah by University of Utah (UOU). Third, a hybrid statistical-analytical methodology is applied for identifying significant factors affecting coal burst. It utilizes data from 30 case studies including those from Utah, Colorado, Kentucky, and other eastern U.S. mines. The statistical approach reinforces field measurements and points to strata rigidity, joint spacings, and horizontal stress field as significant factors affecting damage resulting from coal bursts. This provides practical capabilities for identifying operations of higher risk using a rigidity-cavability variable. Overall, the study provides valuable insights into the mechanics and risk factors associated with coal bursts in major U.S. coalfields. By utilizing a multipronged approach that incorporates both field measurements and statistical-analytical calculations, the study offers practical capabilities for identifying operations of higher risk and improving coal burst control.

Jul 1, 2023

By Michael P. Evans

Traditionally in coal processing jigs have been used to clean the coarse coal fraction, the +3/8" or +1/4" material. Today with the advent of modern fine coal jigs in the United States, its place was moved from the coarse to the inter- mediate coal circuit, the 3/8" x 100 mesh. The most economical coarse coal circuit to build and operate is a heavy media bath circuit. The following table summarizes the cost per raw coal ton processed for a coarse coal jig circuit, and a coarse coal heavy media bath circuit. The flowsheets used to compare these two circuits are shown in Figures 1 and 2.

Jan 1, 1983

By Ramiro da Conceição do Nascimento, Horst Guenter Feldhagen, Rafael Piumatti de Oliveira

Mixed hydroxide precipitate (MHP) is a nickel intermediate product that has economical benefits to downstream leaching of lateritic marginal ores. Usually, this product is subsequently processed and refined to produce nickel by hydrometallurgy, but an alternative route can be made integrating hydrometallurgy and pyrometallurgy. Assessing the overall consumption of ferroalloys to obtain stainless steel, as an increasing practice performed in China, the synergy of nickel extraction from laterites by leaching and precipitation asMHP with the production ofMHP agglomerates applied as rawmaterial to furnaces of ferronickel production is a very attractive practice. This work aims to further the technological development of an agglomerated product feasible to hydro-pyro integration. The agglomeration experiments were performed by traditional pelletizing (firing the pellets) and cold bonded pelletizing (aging the pellets by appropriate stocking). Appropriate compositionswere prepared withMHP, additives and binders for each of these routes. A specific study of binder composition was made to find an adequate melting point. The produced pellets were tested to prove their properties by crushing strength tests. The standardization applied to iron ore was followed. The best result of crushing strength was 98.52 daN/pellet. The agglomerates with approved crushing strength for use in electric furnaces were smelted to produce alloys containing nickel; the agglomerates were characterized by scanning electron microscopy. The alloy obtained was metallic ferronickel with sulphide precipitates. Therefore, MHP pellets can be precursors of nickel alloys, which have to be refined to obtain the desirable composition.

Jul 6, 2020

By F. Calizaya, S. Bhattacharyya

"This study presents the results of a set of sound level measurements carried out in three underground mines where auxiliary fans are used regularly. Sound levels as high as 100 dB(A) by the workings and 115 dB(A) by the fans were measured in these mines. These levels are quite high even for intermittent noise. Ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard-rock mines are presented here. Factors such as fan type, rotational speed, and silencer-duct arrangements and their effects on noise attenuation are discussed. INTRODUCTION Auxiliary fans are used in hard-rock mines extensively. They are used to ventilate development headings, crusher rooms, conveyor transfer points, and underground shops. They are also used in developing long tunnels and ramps. Depending on the flow requirements and space restrictions, single or double stage axial fans with rigid or flexible ducts are used. Usually, they are high pressure (3.75 kPa) fans with flow rates ranging from 7.1 m3/s to 30 m3/s. The input power varies from 15 kW to 113 kW (Mutama, 2004; O’Connor, 2008). Typically, a 113 kW fan can produce sound levels as high a 113 dB(A) (Howes, 2005). Silencers are often omitted for cost reduction purposes or when used, they are not well maintained. Furthermore, silencers provide limited attenuation depending on their length and type. Typically, the sound attenuation ranges from 10 dB(A) for a 1 × D silencer to 14 dB(A) for a 2 × D silencer, where D is the fan diameter. In a mine, the silencer is subject to wear and tear, especially when the silencer is used in harsh environments. The interior lining can get clogged and the acoustic fill can get covered by dust and diesel soot, thus reducing the silencer performance. Periodic cleaning of the interior casing can increase the attenuation capacity of a silencer by 6 to 9 dB(A) (Dabson & Acuña, 2017). However, this requires a special silencer design in which the inner cartridge can be removed, the sound absorbing material replaced, the inner casing cleaned and the whole set retrofitted. A number of techniques can be used to reduce auxiliary fan noise in underground mines. These range from selecting the right fan for the job to installing adequate silencers. The choice depends on the air quantity requirement at the working place, cross-sectional area of the opening, duct diameter, fan type (axial or centrifugal) and local restrictions. Auxiliary ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard rock mines are presented here. Factors such as fan type, rotational speed, duct diameter, and silencer-duct arrangements and their effects on noise attenuation are discussed."

Jan 1, 2019

By A. Cummings

This paper reports two aspects of reactivity of complex Ni-Cu sulphide ores: variations that result from stockpiling of a nickel-copper sulphide ore in the Sudbury area and its consequences on flotation behaviour, especially in terms of metal losses to scavenger tails. In relation to the first aspect, self-heating characteristics of the stockpile were carried out by monitoring the internal temperatures of the stockpile. Six heat sensors were installed with respect to external conditions in local weather during a 7-month period. Stockpile temperatures were mainly influenced by ambient temperature with some retardation effects. The maximum temperature recorded in the stockpile was 44 °C. Samples taken at the beginning and at the end of stockpiling were tested to assess variations in behaviour of the rougher-scavenger flotation. Relative to the fresh ore, nickel and copper losses in flotation of the stockpile fines were 5.0 and 3.6 %, respectively. The fresh ore yields concentrates with higher nickel grades due to differential flotation behaviour of pentlandite and pyrrhotite relative to the stockpile fines, which exhibit a truly bulk flotation behaviour at least during the first 3 stages.

Aug 1, 2013

By A. W. Jolliffe

AEROPROSPECTING may be defined as the application of the air view to the search for mineral deposits. The term is suggested as a preferable alternative to either aerial prospecting (which may be confused with areal prospecting) or air prospecting. The air view may be obtained by visual observation from an aircraft or by examination of air photographs; each has its particular advantages and disadvantages. Aeroprospecting should be regarded only as an aid to, and not as a substitute for, accepted prospecting methods ( l ). The Precambrian region north of Great Slave lake consists of two well defined physiographic units, a feature first noted by J. T. Wilson (2). The boundary between these lies close to the north shore of the east arm of the lake and extends northwesterly near Spencer, Beniah, Carp, and Ghost lakes (Figure 1). South and west of this line, exposed bed-rock makes up the greater part of the land area; eskers are very rare, and overburden is largely limited to rock-walled valleys and depressions. North and east of the line, outcrops are rare or absent, eskers are abundant, and most of the surface consists of drumlin-like drift hills, elongated parallel to the direction of ice movement (Figure 2). Where this boundary passes through the area shown in Figure 1, it lies near the 1,200-foot contour and may mark the maximum extent of the lake or sea arm present in this vicinity toward the end of the Pleistocene period. For convenience, the first area may be called the 'bed-rock belt' and the other the 'drift belt'.

Jan 1, 1945

By R. D. Brittain

In order to analyze and control the transport of harmful trace-element impurities in various smelting processes, it is necessary to have fundamental information about the chemical thermodynamic properties of the pertinent condensed and vapor phases. This paper describes recent thermodynamic studies of the gaseous arsenic sulfides and of the activity of arsenic in a copper-iron sulfide matte phase. These studies were carried out by high temperature mass spectrometry and by effusion vaporization techniques, which permitted clear identification of the molecular species involved, a decided advantage in such complex systems. The nature of the results obtained and comparisons with previous interpretations will be described.

Jan 1, 1983

By Luis de la Pe[n]a Porth

The present process refers to a method for efficiently obtaining high purity metallic copper from copper ammonium sulfite. Essentially, this process consists of submitting the copper ammonium sulfite to the action of heat and pressure with the object of obtaining by the decomposition of it, metallic copper, ammonium sulfate, sulfur dioxide, and sulfuric acid.

Jan 1, 1974

By A. K. Raji, M. O. Ojumu

Robotic subsea dredging crawlers are dynamically and remotely controlled vehicles that are used for deep sea mining and recovery operations. These exploration machines are released from a mother ship and move around on the ocean floor using tracks. Current ocean crawlers such as the MK3 ROST are hydraulically powered. In this paper we develop a scaled-down model for simulating and performing static loading analysis of an electrically powered robotic subsea dredging crawler (EPRSDC). The modeling, simulation, and analysis were carried out using modelling software from Solidworks. The structural frame was assembled using the Tetrix max robotics kit. The kit’s structural components were produced from 1050 aircraft-grade aluminum. The results were used in optimizing and for considering other materials, and the to identify specific areas to be reinforced in future crawler designs.

Oct 3, 2023

By C. A. Rhoades

A major contributor to the problem of short life expectancy for blade-type conveyor belt cleaners is uneven wear along the blade edge. Uneven wear results in the formation of channels in the blade edge, which allow material to be carried back between the blade and the belt. In an effort to reduce the uneven wear problem, the U.S. Bureau of Mines has studied the mechanisms responsible for effective belt cleaning. From this study emerged a design for a cleaner blade that would greatly reduce uneven edge wear. The design consists of a standard cleaner blade incorporating air passages that allow for the expulsion of air along that part of the blade edge in contact with the conveyor belt surface. The results of 18-h tests indicated that the expulsion of air on the blade edge prevents scratches from developing into deep grooves. These tests showed that effective blade cleaning life can be extended 25 times using the pneumatic cleaning blade, compared with solid metal cleaning blades.

Jan 1, 1989

By Y. Pan, V. V. S. Vytla, P. Tukkaraja, R. BHARGAVA, S. Jayaraman Sridharan

Panel caving is an underground bulk mining method that utilizes gravitational force for mining massive, steeply dipping, and deep-seated ore deposits at a lower operating cost. To control dust and gas emissions entering the production level during the extraction of ore from the draw points in a panel cave, relatively negative pressure is created in the cave by installing an exhaust fan in the exhaust drift located on top of the cave. Since caving is a dynamic process, the design of an effective ventilation system is a challenging task, and therefore, estimation of airflow resistance offered by the broken rock inside the cave is critical. The complex and dynamic nature of caving also makes it difficult to predict the airflow resistance by using traditional approaches. This study investigates the effect of changes in the bulk porosity of the broken rock on the cave airflow resistance using computational fluid dynamics (CFD) approach. The results show an inverse relationship between the cave airflow resistance and the bulk cave porosity. The pressure-quantity characteristic curves presented in this paper provide valuable information for sizing and operating an exhaust fan used for a mature panel cave ventilation.

May 17, 2022

By Robert K. Jonas

"Minerals processors can improve production by using the best available control technology to control their operations. Many mines use expert systems that can provide improved results over manual or basic control, but better results can be achieved using multivariable predictive control. Over the past few years, the application of multivariable predictive control has gained acceptance in many mining processes and has recently proven to be suitable for some of the most challenging processes. This advanced control technology has been successfully applied to a wide variety of processes; alumina digestion, ball mills, CCD/thickeners, kilns/calciners/roasters, heat exchangers/evaporators, and more demanding processes like SAG mills and flash smelters.This paper discusses the needs of advance control technologies in the mining industry, including the impact of these technologies on best practices for implementation and long term sustainability. Results of the multivariable predictive control applications in mineral processing are discussed, and in particular the application to the SAG mill. In addition, an example of the benefits improvement that can be achieved with this technology is presented.INTRODUCTIONThere has been a long term perception in the mainstream mineral processing industry that best advanced control solution is an expert system. There a numerous instances of expert systems used for control of SAG mills, as well as kilns or roasters, thickeners and more recently flotation circuits. Many of theses expert systems have been installed by small, independent companies or by OEMs of processing equipment. Undoubtedly these expert systems have provided millions in benefits to the owners of mineral processing plants.It is this author’s proposition that it is a misconception to believe that expert systems are the best solution for mineral processors, and that in many cases the best solution is Multivariable Predictive Control (MPC). Better control and optimal operations can be achieved through the use of MPC. Another important consideration when considering advanced control technologies is the implementation and support effort. These types of applications have been known to deteriorate, even to disuse, when they are not kept up to date with changes to the process or equipment. The audience is invited to listen to discussion and draw their own opinion. The author has been involved in installing control systems for over 20 years, advanced solutions for over 15 years, and has had privilege to consult with many miners concerning the selection and application of advanced controls over the past 6 years."

Jan 1, 2008

By Colin Lawrence

The Port of New York and New Jersey is one of the most heavily used transportation arteries in the world, handling nearly 40 per-cent of the North Atlantic shipping trade and directly providing nearly 230,000 jobs to the local economy. In 2004, $100 billion worth of consumer goods moved through the port. To accommodate future cargo volumes in the port, which are expected to double over the next decade and possibly quadruple in 40 years, deeper shipping channels are needed to provide access for a new generation of cargo mega-ships with drafts exceeding 13.7-m (45-ft) when loaded. Current channels within the harbor range in depths up to 13.7-m (45-ft), thus preventing carriers from using these larger ships, or requiring significant reductions in cargo to achieve lesser drafts to operate safely within the harbor. As part of the Harbor Deepening Project, the Anchor-age Channel would be deepened to 15.2 m (50 ft) below mean low water (MLW), for a length of 5,790 m (19,000 ft). The New York City Department of Environmental Protection (NYCDEP) owns, operates and maintains two existing water siphons in the harbor. Due to their shallow depth, both existing siphons must be relocated before dredging of the Anchorage Channel can be completed. Tom Costanzo, manager of capital programs for the Port Authority of New York and New Jersey (PANYNJ), says that ?While the re-location of the existing siphons under the Anchorage Channel is vital to the success of the deepening program, it is also a story of cooperation among key agencies at different levels of government resulting in improvements that will benefit the people of this region greatly.?

Jun 1, 2010

By E. Petrakis, K. Komnitsas

The main objective of batch grinding modeling is the estimation of the product particle size distribution over time or specific energy input to the mill. So far, the developed analytical methods require often complicated calculations which are timeconsuming. Thus, more simple approaches that allow the reliable prediction of the complete product size distribution need to be developed. In the present paper, an approach, based on the population balance model (PBM), that reliably predicts the product size distribution is proposed. In order to enable this, the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (R-R) distribution, thus allowing the determination of the breakage rate for each grinding period. A time-dependent breakage rate framework was developed where the traditional linear theory of the PBM is considered a partial case. This approach allows the deviations from the linear theory to be categorized and the degree of the acceleration-deceleration of the breakage rate to be predicted. Modeling results were validated by laboratory grinding studies using two homogeneous materials, quartz and marble, and one heterogeneous, a limonitic laterite. The experimental data revealed that grinding exhibits non-first-order behavior and the degree of deviation from the linear theory depends on the tested material. The reliability of the proposed model was validated with the use of the distribution modulus n, the a value of the breakage rate parameter, and the optimum n values that minimize the sum of the differences between the experimental and estimated particle size distributions.

Feb 8, 2021

By Sebastiaan Peelman

NdFeB permanent magnets are the best available magnets used in many technology applications. However, at their end-of-life (EoL) most of magnets and the contained REEs are lost during the recycling of the bulk metals. The REEs are classified as the most critical raw materials in the European Union, and recycling of REEs from EoL products will reduce their criticality and contribute to the sustainability of REE. Various technological routes have been reported, but most of the methods are effective for highly concentrated magnets or magnet scrap, which is greatly dependent on expensive pre-dismantling processes. This paper presents various innovative metallurgical solutions to the effective REE recovery from current industrial practice for WEEE recycling, including the ferrous scrap from WEEE shredder products and shredder residues from computer hard disk drives. Both hydrometallurgical and combined hydro- and pyrometallurgical REE recovery routes are developed after demagnetization and physical upgrading.