Search Documents

By P Holt, M Allen

On the first of July, 2012, the Australian GovernmentÆs Clean Energy Act commenced. From this point, a price of $23/t of CO2-e will apply to facilities that trip the liability threshold. This first part of this paper concentrates on the mechanics of the Clean Energy Future legislation and how it will be applied to the mining and mineral processing industry.The second part of this paper contains analysis of the data presented for typical mine operations. Methodologies for constructing a carbon strategy are also presented. This will entail determining what the objectives of the carbon strategy are, and defining what the strategic priorities for a business should be. An action plan to address the risks identified from the Clean Energy Act is also developed as part of the strategy.Details such as the advantages and disadvantages of opting into the carbon price scheme for liquid fuels are shown. Other considerations such as the ability to acquire permits through the carbon farming initiative or through overseas clean development mechanism projects are explained.CITATION:Allen, M and Holt, P, 2012. Implications of the carbon price and developing a carbon strategy, in Proceedings International Mine Management 2012, pp 105-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By J. A. Gutierrez-Rodriguez, R. J. Purcell, F. F. ApIan

"Based on contact-angle measurements and the work of adhesion equation, the hydrophobicity of a wide variety of coals was found to decrease with decreasing rank, fixed carbon and total carbon content and with increasing oxygen and hydroxyl content. The estimated hydrophobicity, based on the water-sessile-drop contact angle, is '\.. 20% for lignite, increases with increasing rank up to a maximum of 'V70% for low (LV) and medium (MV) volatile bituminous coals and then decreases somewhat for anthracite. Using the captive-bubble technique, the calculated hydrophobicity ranges from '\.. 0% (below HV A bituminous rank) to a maximum of 55% for L V-MV coal. The former estimation is believed to be the more accurate. While the water-sessile-drop contact angle as measured on a polished-coal surface is usually larger than that shown by the captive-bubble method, the two values were found to converge at""' 95% relative humidity. It is proposed that the surface of coal consists of three kinds of sites: strongly hydrophobic, weakly hydrophobic and hydrophilic. The sessile-drop technique measures the total hydrophobic sites whereas the captive-bubble method measures only the more strongly hydrophobic sites. A water film covers the weakly hydrophobic sites preventing their detection by the captive-bubble technique.INTRODUCTIONCoal is a mixture of the degradation products of plants and of mineral matter. The appearance and properties of a specific coal is determined by the nature of the original vegetation and the extent of the physical and chemical changes which have occurred after deposition. The coalification process may be considered to have started with peat formation followed by a transition to lignite due to burial under sediments and metamorphic processes. Further metamorphic transformation to bituminous coals and, finally, under intense metamorphic action, to anthracite causes the carbon content and rank of the coal to increase. With such a wide variation in their genesis and composition, equally wide variations in the degree of hydrophobicity of different coals may be expected. It is the purpose of this paper to provide a means of estimating the hydrophobicity of a given coal sample based on rank parameters."

Jan 1, 1989

By G. L. Oldright

As sponge iron is much like porous, coarse sand, it is a tempting material to use in place of coarse scrap iron as a precipitant of metals, for scrap iron is relatively awkward to handle and exposes only a small amount of surface to pregnant solutions. The results of the experiments described in this bulletin are largely a record of the behavior of sponge iron as a precipitant of lead and copper under laboratory conditions comparable to those that would obtain in a commercial plant were it attempted to secure the maximum contact of surface between solution and precipitant. Physically, the study is largely one of the rates of diffusion of the metal ions in the solutions and through the metallic coatings surrounding the sponge iron particles. The practical objectives are to remove completely the valuable metals from solution and at the same time to obtain a precipitate of good grade. In order to fulfill this latter requirement, the precipitant should be almost completely consumed. These practical ends are usually secured by having the two substances involved pass each other counter-currently-that is, in such a manner as to have the strongest precipitant in contact with the most impoverished solution, and vice versa. EXPERIMENTS WITH LEAD SOLUTIONS In nearly all of the schemes involving the leaching of lead from its ores the metal has been put into solution as the chloride, and fairly concentrated liquors have been employed. The solubility of lead under such conditions is comparatively small at best; the hot pregnant liquors from which the metal is to be precipitated are then made nearly saturated with respect to lead, and only a very small amount of acid is used. Therefore it was not as necessary to learn the behavior of the sponge iron in precipitating lead from solutions of widely differing composition as to learn under what conditions, and with what mechanisms, this precipitation might be carried out most readily.

Jan 1, 1928

By Amit Srivastava, Monica Malhotra

In a congested city or urban area, so called “lifeline of the city”, i.e. Gas, Electricity, telecommunication, as well as other utilities or facilities are supplied or transported underground through buried pipes or utility tunnel. Sometimes these buried pipes or utility tunnels are deep underground and interfere with the foundation of new structure. It is highly probable that a pile foundation is placed near an existing underground buried pipe or utilities tunnel and may influence its load bearing capacity. Hence, estimation of reduce load bearing capacity of the pile foundation placed near the existing buried conduit or utility tunnel is a complex soil-buried structure interaction problem. It is further complicated owing to uncertainty in estimation of geotechnical parameters of foundation soil due to measurement and testing errors, inherent soil variability and model transation. Under such circumstances, load bearing capacity is best assessed in probabilistic framework or through reliability analysis. The present study demonstrates how concept of response surface method (RSM) in conjunction with Numerical Analysis and First Order Second Moment (FOSM) methods can be combined to per the reliability analysis. The study answers the following question “reliability in reduction in the load bearing capacity of single pile placed near the existing underground pipe or utilities tunnel”. It is demonstrated that the approach provides first hand ination on the reduction in the load bearing capacity and then estimate the reliability of that estimation in terms of an index called Reliability Index (). Such preliminary investigation can be useful for advocating the detailed analysis as well as in the decision making for relocation of pile foundation.

Sep 1, 2022

By BUREAU OF MINES

PLATINUM

Feb 1, 1922

By M. Dworzanowski

The difference in the magnetic properties of minerals is the basis for magnetic separation. All minerals can be generally classified as ferromagnetic (strongly magnetic), paramagnetic (weakly magnetic) or diamagnetic (non-magnetic). Magnetic separation can be conducted dry or wet. The majority of the applications of wet magnetic separation in the mining industry are based on the wet drum magnetic separator. The wet drum magnetic separator has been in use for over 50 years and its design is based on a rotating drum installed inside a tank. Inside the drum are stationary, permanent magnets arranged in an arc to provide the magnetic field. These magnets can be of the ceramic ferrite type providing a low intensity magnetic field or of the rare earth type providing a high intensity magnetic field.

Jan 1, 2010

By B Young

Variable bench heights, interaction with underground workings and a steeply dipping orebody are challenges faced daily by geologists at Xstrata Zinc’s Black Star Open Cut (BSOC) Zinc/Lead/Silver mine in Mount Isa, Queensland.BSOC has been in operation since late 2004 and was developed to extract the surface extents of the Zn/Pb/Ag mineralisation mined in the underground lead mine. To date many large scale stopes and extensive development drives have been intersected and successfully mined. The stratigraphically hosted orebodies strike in a north-north westerly direction, dipping ~75° west. Ore production from the pit is currently at 4.5 Mt/a.Historically, sampling was conducted using a multiple spear technique from blasthole cuttings. This method proved to be relatively reliable when blasting benches at a consistent height, but a requirement to vary bench heights to safely collapse and then mine through underground workings reduced sample representivity to unacceptable levels.The purchase and commissioning of a production rig which had been converted for reverse circulation (RC) has allowed for the flexibility of a small rig, with the capacity to easily drill 48 m holes while ensuring sample quality. Sample quality is not the only benefit of introducing RC grade control. By collecting grade control data well in advance, informed decisions can be made by planning, drill and blast and mining departments weeks beforehand, rather than hours before firing. Additionally, seeking operational value to offset higher drilling costs has proved positive with benefits including increased confidence in orebody wireframes, accurate tonnage and grade for proceeding five benches along with the ability to representatively test metallurgical response on a tight grid spacing.

Aug 22, 2011

By Herbert H. Kellogg

Graphs representing the standard free-energy of formation as a function of temperature for 21 fluorides are presented, along with estimated values for the standard free-energy of formation of 20 atedadditional fluorides. A few of the many possible uses of these data in metallurgical calculations are discussed, including the fluorination of oxides, sulphides, metallurgicaland chlorides, and the reduction of metal fluorides. RECENT papers which have presented free-energy data for oxides, sulphides, chlorides, carbonates, sulphates, and silicates in the form of free energy vs. temperature plots,1-5 have found important uses in teaching and metallurgical development work. This method of presentation of thermo-dynamic data serves to make available in readily usable form thermodynamic constants which are scattered throughout the literature, and to show by graphical means the stability relations which exist between the compounds of a given type. It is certainly desirable to have these free-energy-temperature diagrams for as many types of compounds as are of present or potential use in metallurgical processes. Thus, even though there are but few uses of metallic fluorides in extractive metallurgy today, the potential uses of fluorine processes are of great importance and serve as the principal justification of this paper. Recent developments in the production of fluoro-carbons have resulted in vastly improved methods for the production and handling of fluorine and corrosive fluorides, with consequent reduction in costs.".' The extractive metallurgist should no longer overlook possible fluorine processes when development of a new process for a relatively high unit-price metal is being considered. In a previous paperv he author outlined in some detail the importance and use of free-energy data in metallurgical calculations and also discussed the properties of a standard free-energy vs. temperature diagram. The same method of presentation is adopted in this paper, and the reader is referred to the earlier work for explanations of the use of free-energy data. Thermodynamic Data This paper presents standard free-energy vs. temperature diagrams, Figs. 1 and 2, for those fluorides for which the major thermodynamic constants are known. In the calculations of the standard free-energy of formation (AGO), values of the enthalpy of formation at 298°K (?Ho,) were taken from "Selected Values of Thermodynamic Constants"8 most of the values of standard entropy at 298°K (S°298) were taken from "Selected Values"," but in a few cases the values given by Kelley9 ere preferred; data for the Phase changes came from "selected Values" and several of Kellley's publics- tions;0-12 and most of the specific-heat data were taken from Kelley.l0 The appendix gives a detailed list of the sources of the data. As explained in an earlier paper,6 he accuracy of some of the standard free-energy relationships is not high. An error of +1 kcal at 1000°C is expected in most of the curves of Figs. 1 and 2. The error may be as high as +3 kcal in some of the curves. Rather than attempt to estimate the reliability of each curve, the source of the data used is reported in the appendix, and the reader may compare these data with newer values as they become available. Figs. 1 and 2 fail to show values for the fluorides of many important metals. In most cases this is because the entropy of the metallic fluoride is unknown. For preliminary calculations it is often useful to have available the best estimate of an unknown datum, rather than no information at all. With this in mind, Table I lists estimated standard free-energy values for a number of important metallic fluorides not included in Figs. 1 and 2. The values reported in Table I were, calculated by Brewer et al.13 and are based on estimated entropy values. The estimated uncertainty of the values for each fluoride were calculated from the uncertainty values given by Brewer1' for ?H°, and the entropy function.

Jan 1, 1952

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By Richard Hamburger

Calculating machines permit the use of the more rapid cotangent and semigraphic solutions of plane triangulation. The results of these methods are as accurate as those of other methods. Simple adjustment of the net, and ease of calculation encourage more complete field work. Errors in field work or in computation are easily localized.

Jan 1, 1950

By Anja Pfennig, Axel Kranzmann, Phillip Zastrow

"Properties of pipe steels for CCS technology require resistance against the geothermal corrosive environment (heat, pressure, salinity of the aquifer, CO2-partial pressure). To predict the reliability of two different injection pipe steels with 13% chromium and 0.46% carbon (1.4034, X46Cr13) as well as 0.20% carbon (1.4021, X20Cr13) steel coupons were heat treated by comparable routines prior to long term corrosion experiment (60°C, 100 bar, artificial brine close to a CCS-site in the Northern German Basin, Germany). In general higher carbon content exhibits better corrosion resistance with respect to corrosion rate, amount of pits and maximum intrusion depth in the case of local corrosion. At 100 bar hardened steels with martensitic microstructure have the lowest corrosion rates with an average of 0.003 mm/a after 2000 h exposure time. At ambient pressure normalized steels show the lowest corrosion rates, indicating that the corrosion is driven by grain boundaries.IntroductionEngineering a geological on-shore saline aquifer CCS-site (CCS Carbon Capture and Storage [1-3]) corrosion of injection pipe steels may become an issue when emission gasses, e.g. from combustion processes of power plants, are compressed into deep geological layers [4-8]. Typically 42CrMo4 (1.7225, AISI 4140) is used for casing, and for injection pipe the steel X46Cr13 (1.4034, AISI 420 C) or X20Cr13 (1.4021, AISI 420 J) is used. Saline formations are the most favorable storage sites in Germany [9], because of their large potential storage volume and their common occurrence. Leakage of CO2 back into the atmosphere may be a problem in saline aquifer storage, especially around the water level within the borehole. Carbon dioxide corrosion may cause failure of pipelines and wells as known from the oil and gas industry [4,6,10,11, 12].From thermal energy production it is known, that the CO2-corrosion is sensitively dependent on alloy composition, contamination of alloy and media, environmental conditions like temperature, CO2 partial pressure, flow conditions and protective corrosion scales [6-8,13- 20]. Considering different environments, aquifer waters and pressures, the analyzed temperature regime between 40 °C to 60 °C is a critical temperature region well known for corrosion processes as shown by Pfennig et al. [21-23] and various other authors [10,24-28] (figure 1). Here a maximum around 4.7 mm/year was found for the pit intrusion depth of 13% Cr steel X46Cr13. Still this may be predicted by the rather conservative Norsok-Model used in the oil and gas industry to calculate surface corrosion rates of carbon steels [29]."

Jan 1, 2014

By Alton G. Woody

Like so many installations of its type approaching middle age, the ore processing and shipping facilities in Puerto Ordaz, Venezuela, have taken a lot of twists and turns in their lifetime. The object of this paper is to lead you through these twists and turns and some of the reasoning for them. The need for additional sources of iron are in the United States became evident during the time of the second world war. An exploration team from U. S. Steel located further high quality direct shipping iron are in commercial quantities near Ciudad Bolivar, Venezuela in 1947. Basic decisions were made to develop these reserves for export via the Orinoco River through a new shipping port to be built at the confluence of the Orinoco and Caroni Rivers. The basic concept was for the ore to be loaded directly to ocean going vessels. This was something of a gamble since the basic economics depended upon successfully opening up the main channel of the Orinoco River to deepwater vessels, and the Bethlehem Steel mine in the same area was already working with shallow draft river boats and a transfer station on the coast. Always, the basic philosophy has tended to be to plan with expansion in mind. The original conveyor systems were 1.52 m (60 inches) wide with 200 idlers, whereas 1.07 m (42 inches) or 1.22 m (48 inches) wide conveyors could have carried any production foreseen at the time of installation. Stockpiles have been located and designed with room for expansion. Basic designs have had dotted line future expansion blocked in.

Jan 1, 1978

By Hong-wei Ma

With social development and technological advancement, mine rescue robots used in complex environments have developed as a research hotspot. This paper reviews the progress of research on coal mine rescue robots, and key technologies of rescue robot design are put forward, such as mechanical structure, self-navigation and self-orientation, multi-sensor information fusion, multi-robot cooperation, and wireless communication technology.

Aug 1, 2013

THIS bulletin presents all analytical and lest methods regularly used by Bureau of Mines laboratories for characterizing coal and coke. To provide better service to coal producers and consumers, the scope of this bulletin has been expanded to include important test methods used to evaluate coal properties for commercial processing. The methods described will prove valuable to all persons interested in analyzing and testing coal and coke.

Jan 1, 1967

By C. J. Walker, J. S. Miller

This work was done in an attempt to find a simple solution to the problem of simultaneously changing terminal rate and terminal pressure under conditions of unsteady - state flow in porous media . Although the original aim was not realized , a method for encasing a sandstone core that would permit high - pressure ( 200 to 980 psi ) flow tests and the use of electronic equipment to measure pressures at points along the core during unsteady - state gas depletion was found to be feasible . The sandstone core used in this study was from the Bandera formation of Pennsylvanian age , Redfield , Kans . The core , cylindrical in shape with a 3.5 - inch diameter and 6- foot length , had a porosity of 15 percent and a permeability of 9 millidarcys .

Jan 1, 1963

By Ramsey Hart

MiningWatch Canada is the only national independent civil society organization with an exclusive focus on mining in Canada and Canadian mining companies operations internationally. In 2005, MiningWatch Canada collaborated with other NGOs to develop the Framework for Responsible Mining: A Guide to Evolving Standards. The project was the result of a perceived need by NGOs and retailers, particularly from the jewellery sector, for a framework that would set out environmental, social, and governance standards for the minerals sector ?providing recommendations for retailers and others seeking to source or invest responsibly, as well as regulate and encourage responsible mining practices?. This paper is a reflection on the Framework that examines key areas of concern and notes where the industry norms and expectations of civil society have evolved. The paper focuses on developments in social issues related to the UN Guiding Principles on Business and Human Rights, new initiatives associated with financial transparency, the UN Declaration on the Rights of Indigenous Peoples. The environmental components of the Framework that are revisited are waste management, biodiversity, energy and climate change, environmental assessment, mine closure, mercury and seabed mining.

Aug 1, 2013

By D. Bessinger, J. Rabe, J. Zietsman, C. Coetzee, P. H. Lamont, J. Muller

The UCAR® CHILL-KOTE? freeze lining concept combines wall cooling with carbon and graphite refractories of higher thermal conductivities to ?chill? the refractory lining by transferring heat from the refractory lining. Effective sidewall water cooling, together with the efficiency of the heat dissipating conductive refractories, lowers the temperature of the lining to below that of the molten process materials. This causes a layer of slag and process metal to solidify or ?freeze? and form a protective ?skull? which completely coats the refractory hot face. Once formed, the slag skull insulates the refractories, reducing heat loss and protect the lining from erosion, chemical attack, thermal shock, and other stresses. The result: extended life and greatly improved refractory performance. The Ilmenite smelting process depends on the presence of a solidified slag skull to protect sidewall refractory material from chemical attach by molten slag. No known refractory material is able to withstand this corrosive material. To date, UCAR has not applied their Chill Kote ? technology in the ilmenite smelting industry. This paper revolves around the results obtained from conducting an ilmenite smelting campaign on a 500kW DC open-arc furnace with a UCAR designed refractory system. The purpose of this test was to establish the effects such a lining has on refractory wear and the reduction-smelting process. Proper thermo-couple management enabled the authors to monitor lining wear for the duration of the campaign. Prior to the pilot-scale campaign, modeling work was completed to evaluate the feasibility of applying UCAR® CHILL-KOTE? technology to ilmenite smelting furnaces. The successful operation of a pilot-scale furnace equipped with the UCAR® CHILL-KOTE? lining as well as concise modeling suggest that it should be a viable option to consider for an industrial-scale furnace.

Jan 1, 2007

By M. S. Prasad

In earlier work it has been shown that paper filler clay products can be obtained from primary kaolin deposits of Minnesota. The objective of the current work was to reduce silica and iron contaminants and to maximize kaolin recovery to higher value products suitable for paper coating. This results in achieving a finer and cleaner product conforming to paper coating specifications. Cationic flotation and high gradient magnetic separation were used to remove free silica and iron, respectively, while attrition grinding and ultrasonics have been examined for particle size reduction. The results of this work are presented and discussed particularly with respect to application-oriented product properties. Budgetary estimates are presented for a 200,000 ton/year processing plant based on the process flowsheet developed and optimized by the study.

Jan 1, 1991

By Hartmut Rossel

VAW aluminium AG has built a "Recycling-Technikum" (Recycling Research Centre) to add a new arm to the company's Corporate Research and Development Department. The Recycling Research Centre, a pilot plant for scientific research, has been in operation since September 1993. These state-of-the-art facilities allow the investigation and optimisation of recycling techniques in 'a global way and in detail. Research is concentrated on the unit operations - processing, melting and waste-gas purification - with the available installations making it possible to compare different alternative process combinations on a 100-kg scale. One of the main targets of VAW research is the development of recycling techniques for packaging. The paper presents an approach to recover the aluminium contained in flexible packaging materials using an integrated melting and waste-gas purification system.

Jan 1, 1995

By M Uceda, E Guerra, Y Choi, J L. Shepherd

In this paper we describe the leaching characteristics of pure gold in thiosulfate solutions that contain a known chelator; meso-2,3-dimercaptosuccinic acid (DMSA). The interfacial and chemical characterisation of the system was accomplished using both electrochemical methods and inductively coupled plasma mass spectrometry (ICP-MS) analysis after pure gold samples were exposed to solutions composed of 65 mM Na2S2O3, 1 mM NaOH and a range of DMSA concentrations. In the absence of DMSA, cyclic voltammetry revealed the onset of thiosulfate mediated gold dissolution, the degree of which was reduced at more positive potentials due to the formation of oxidised thiosulfate products on the gold surface. The addition of small amounts of DMSA (<10 ¦M) to the electrolyte resulted in minor changes to the voltammograms indicating a subtle interaction of the additive with the gold surface that may improve leaching. However, at higher concentrations of DMSA (up to 100 ¦M), electrochemical evidence suggests the formation of new oxidation products in solution as well as the formation of more compact monolayers of DMSA on the surface, which contribute to partial repassivation of the surface. The influence of DMSA on thiosulfate leaching of pure gold electrodes at the open circuit potential for a period of 90 minutes was tested and the corresponding gold leaching performance evaluated with ICP-MS analysis. Our data shows that small amounts of DMSA (1 ¦M) doubled the amount of total gold in solution when compared to the same study in the absence of the additive. However, higher concentrations (5 ¦M DMSA) reduced the overall amount of dissolved gold. These results may point to a mechanism where small amounts of DMSA improve leaching by adsorbing onto the surface in a highly defective monolayer that partially blocks or disrupts the formation of passivation products caused by thiosulfate oxidation, but excess DMSA can limit the leaching process itself by forming too coherent a monolayer on the gold surface.CITATION:Uceda, M, Choi, Y, Shepherd, J L and Guerra, E, 2013. Investigating the influence of meso-2,3-dimercaptosuccinic acid on thiosulfate leaching of bulk gold electrodes, in Proceedings World Gold 2013 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013