Search Documents

By A. J. Dudzik

In 2006 Arch Materials initiated the development of an underground limestone mining complex. The decision to proceed with the project was the end result of several years of market research and geological reconnaissance. The scope of the project included the construction of two declines to the mining horizons located approximately 900 feet below the surface, the means and methods of this phase will be the primary focus of this discussion. The design, fabrication and erection of a state of the art crushing and screening processing plant which when completed will have the primary crushing located on the mine level allowing uniformly sized material to be brought to the surface by means of a highly efficient conveyor system and a surface portion of the plant where material would be additionally processed, screened and stockpiled into specific product types. Also included in the scope of the project is the construction of offices, warehouse and shop facilities necessary to support the operations, commercial sales and distribution of the finished products.

Jan 1, 2010

By J. Alexandre

The use of bricks of soil-cement is proving to be an important constructive methodology due to low environmental impact in the production process of these blocks comparing with conventional bricks are burnt, besides being easy to produce. However during the process of production of bricks, which are compressed, knowledge of the properties of the soil used is critical to the quality and durability of the blocks. The objective of this work is to evaluate the feasibility of using soil from the municipality of Goytacazes for the production of soil-cement bricks. Assays were performed the compaction, liquid limit, plastic limit, particle size analysis, EDX and X-Ray diffraction for later pressed blocks and analyze their compressive strength and water absorption.

Jan 1, 2015

By S. Schutte, J. Pelders

Worker participation in equipment development can result in improved user acceptance and product quality. This paper focuses on worker engagement in equipment development processes in the South African minerals sector. Qualitative data was gathered during interviews with original equipment manufacturers (OEMs) and industry experts. A lack of inclusion in equipment design from workers from all organizational levels in mines was reported. Meanwhile, the historical context and workplace culture of the mining industry (including leadership, trust, training, performance, and remuneration factors) were evident barriers to the implementation of new technology. Worker engagement processes should include securing management commitment, creating multidisciplinary teams, effective facilitation, shared understanding of needs, training and development, and iterative design. Human-centred design approaches and independent platforms for engagement on equipment design requirements are recommended.

Feb 2, 2021

By S. Amid, D. Fisk

"Wireless technologies are permeating the mining and metals industry and enabling a myriad of benefits. With standards such as IEEE 802.11 for wireless devices and ISA100.11a for wireless field instruments protecting their investments, customers look to benefit from the cost and flexibility offered by wireless devices. Using wireless field instruments, plants are eliminating the costs associated with wired system by 50 to 70% and using these savings to install more field instruments, which, when used smartly, enables them to optimize their processes efficiency and equipment reliability. Wireless also empowers a mobile workforce by allowing them to have access to key process and maintenance data directly from the field. This paper describes how wireless can help operations and maintenance personnel to be more effective. Three case studies, illustrating how the mining and metals industry is taking advantage of the technology today, are presented:1.,Optimisation of the water recovery process using wireless2.,Field operations improvement with wireless handhelds3.,Improving fleet maintenance through wireless mobile equipment management"

Jan 1, 2011

By Michael J. Lawrence

"The VALMIN Code was developed and formally adopted by The Australasian Institute of Mining and Metallurgy (AusIMM) in 1995 and a revision was issued in 1998. The VALMIN Code applies to all relevant reports under the Australian Corporations Law, including submissions to the Australian Stock Exchange (ASX) and the Australian Securities and Investments Commission (ASIC).The VALMIN Code and Guidelines sets standards for the preparation and commissioning of independent assessment and/or valuation reports on mineral and petroleum assets or mineral and petroleum securities.It is mandatory for AusllvI:M's members to follow this Code in these relevant circumstances and failure to do so will result in serious sanction of the member by the Ausllvllvfs Ethics Committee. Public support for the use of this Code has been given by regulators (ASX/ASIC) and market participants ( eg major accountancy firms). It is also endorsed as a guide to general best practice in project assessment and valuation.This paper will discuss how the VALMIN Code has worked in practice over the past few years. It will also examine areas where the Code could be improved and how it could form the basis of a new Canadian Code for mineral property valuation."

Jan 1, 2003

By Harry Wilton-Clark

Introduction Coal cleaning may be taken as meaning the separation of coal-as-mined into two or more fractions. Coal cleaning includes coal washing, together with any other means used in the ultimate preparation of coal prior to shipment (as coal) . The method of coal cleaning devised for any given mine must be one which is based entirely on the economic results obtainable. The installation of a high-cost and complex washing plant, designed to produce a low-ash dean coal, at the highest possible recovery, may be unsound practice. A crude 'roughing' washer may be the best result of sound engineering and operating consideration, and in some cases coal cleaning should be confined entirely to preparation at the face. Consideration of complete costs, to the point where the coal is actually sold, may show that certain seams are workable or not workable. Of the seams found workable, extraction of the whole or parts of the seam may be decided on. The portion to be extracted may contain rock or bone partings, which must be removed. It may be good practice to mine the extra portion and remove the objectionable materials by surface washing; or it may be that such materials should be removed underground, even at an increased mining cost. For instance, in some of the steeply pitching seams of the Alberta Crow's Nest Pass district, the removal of bone and rock at the face may be almost impossible under the usual 'up the pitch' or 'angle' mining methods, but possible by mining across the pitch so that the material to be rejected can be removed and gobbed. Again, if a complete seam is being extracted, investigation may show marked differences between top coal and bench coal, and if sufficient mine cars are being loaded from a chute at one time, the fact that such a place is working top or bench coal at the time may be reflected by peaks in ash content or size proportions at the ripple. It may be very effective coal preparation to smooth out such peaks.

Jan 1, 1934

By W. E. Pittman

The Bureau of Mines, as part of its Health and Safety Technology Program, is conducting research on the use of ground penetrating radar (GPR) for mine hazard detection. GPR offers a possibility of mapping immediate below-surface geologic conditions, including faulting and other anomalies, thereby exposing potential safety hazards to miners. This report summarizes a literature review of the current status of GPR research in and outside the Bureau.

Jan 1, 1984

By E. G. Davis

Under a memorandum of agreement with Reynolds Metals Co., Richmond, VA, the Bureau of Mines studied the problem of corundum formation on refractory linings in aluminum recycling furnaces. A laboratory test was developed for evaluating refractories in contact with molten recycled aluminum and identifying the mechanism of corundum formation. A test apparatus was designed and constructed to evaluate the performance of refractory samples. Corundum mechanism formation studies indicated that corundum formed on refractories when there is metal penetration. Once corundum forms, it acts as a wick allowing the molten aluminum to move to the surface where it is oxidized, thus causing further growth of the corundum. Phosphoric acid treatment or a spinel mortar coating prevented corundum formation on the 70-and 90-pct-A1203 refractories.

Jan 1, 1988

By G. R. Peterson

The Bureau of Mines evaluated the potential supply of cobalt from known domestic resources, both as a primary product from some deposits and as a byproduct from others, and found that U.S. production could play an important role in meeting U.S. cobalt needs by the mid-1980's. This production would be of a relatively short duration, however, with production declining significantly before the year 2000. As part of the study, a tonnage-price relationship was developed indicating the quantity of cobalt that could be produced from known cobalt-bearing deposits at various primary commodity prices and at a 15-percent rate of return on the required capital investment. All capital and operating costs are calculated in August 1980 dollars, and commodity prices are based on August 1980 prices. Known U.S. cobalt-bearing deposits which represent the current U.S. cobalt reserve base contain some 310,800 metric tons of cobalt in slightly over 1 billion metric tons of demonstrated mineralized material. Approximately 37 percent of the cobalt contained in the reserve base is considered recoverable using existing technology. Of this quantity, some 87,000 metric tons of cobalt is economically recoverable assuming a cobalt price of $25 per pound, a copper price of $1 per pound, and a lead price of $0.40 per pound. Assuming that the cobalt price decreases to $15 per pound, keeping copper and lead prices constant, the quantity that is considered economically recoverable declines to some 45,700 metric tons. Domestic cobalt consumption in 1979 was 7,900 metric tons (17.4 million pounds). Currently, no primary cobalt is produced from domestic resources, and none has been produced since 1971.

Jan 1, 1981

By Timothy C. Siegel

This report presents the results of a synthesis on the design and analysis of ground improvement for liquefaction mitigation. The synthesis included an industry survey concerning the practice of ground improvement for liquefaction mitigation. Participation in the survey was solicited by advertisements in several trade magazines and by e-mail for the DFI membership. The survey participants numbered 150. Their professional roles include consulting engineers, specialty contractors, design engineers, government engineers, and academicians. They represent a variety of geographical areas including North/Central/South America, United Kingdom, Middle East, Caribbean, Hawaii, Japan, India, Egypt, France, Australia and New Zealand. Upon completion of the survey, several professionals in the field of liquefaction and ground improvement were interviewed for them to elaborate on the survey results. The interviews are included in the Appendix of this report. Financial support for the project was provided by DFI and Dan Brown and Associates PC. The concept of the liquefaction mitigation synthesis was developed by DFI?s Ground Improvement Committee in recognition that: (a) The results of recent research and post-earthquake reconnaissance have challenged previously longheld beliefs about liquefaction and associated mitigation techniques, and; (b) The DFI membership and the engineering/construction industry are interested to know if and how engineers and designers are subsequently adjusting their practice in consideration of recent research and post-earthquake reconnaissance. For more detailed information on recent research and post-earthquake reconnaissance, presentations are available from the State-of-the-Art Forum: Liquefaction Consequences and Mitigation that was held in St. Louis in 2012. A commentary of the state-of-practice in ground improvement for liquefaction mitigation (prepared by DFI?s Ground Improvement Committee) is included in this issue of the DFI Journal. The author would like to thank the participants of the survey and especially Mr. Mike Jeffries, Dr. Les Youd, and Dr. Ikuo Towhata for their willingness to share their expertise in interviews. The author also acknowledges Mary Ellen Bruce of DFI, Billy Camp of S&ME, Inc., and Marty Taube of DGI Menard (and Chair of DFI?s Ground Improvement Committee) for their signifi cant contributions.

Aug 1, 2013

By D. E. Stone

Solid and liquid impurities must be removed almost completely from synthesis gas for the production of synthetic liquid fuels because of their effect on the synthesis catalyst and turbocompressors. The maximum permissible concentration of dust has been set at 0.05 grain per 100 cubic feet.5/ This is one part per million by weight, or about the same concentration as in average city air. The cost of synthesis gas is estimated to constitute 60 to 70 percent of the total cost of the synthetic liquid fuel. For this reason this station is developing processes using coal instead of the more valuable coke as raw material, which promises reduction in cost of the synthesis gas. This, however, increases the difficulty of attaining the above dust value. As failure of the dust-removing equipment to produce high-purity gas may ruin valuable equipment within a few minutes, it is imperative that a reliable and continuous method be obtained for determining such extremely low concentrations .of dust in the purified gas. A suitable device must also instantly sound an alarm and, if necessary, automatically actuate the proper valves to prevent damage. The Ess Instrument Co. designed and built an instrument which they believed might fulfill these specifications. It' continually compared, by means of photoelectric cells, the intensity of a light beam passing through the gas and a similar beam passing through clean air. For maximum sensitivity, the photocells were connected back to back, i.e., anode to cathode and cathode to anode. The difference in voltage produced by the two cells was amplified and operated an indicator.

Jan 1, 1951

By H. Hirayama, T. Okura, O. Kato

"Saganoseki Smelter & Refinery, one of the largest copper smelters in the world, has the annual capacity of 300,000 metric tons in copper content with two flash furnaces, six Pierce-Smith type converters, two anode furnaces, four acid plants, three tank houses and perfect pollution control system.Coping with the many severe conditions surrounding the copper industry in the last decade, Saganoseki Smelter has kept performing the stable operation, while enhancing the smelting capacity and developing new technologies such as the hydrometallurgical treating of converter dust recovered at electric precipitators. Especially in the operation of flash furnaces, which are of Nippon Mining's conversion type using hot air in a temperature of l,000ºC some technological improvements and complete operation control factors have approved the concentrate feed rate to reach to 2,200 tons a day for a flash furnace.Reported in this paper are the production control design for copper smelting process, and the operation control scheme of the flash furnace following the brief review of the characteristic of Saganoseki Smelter's process and some improvements. Copper Smelting ProcessDescriptions of major unit operations and general specifications of the copper smelting facilities are summarized in Table 1, and the present flowsheet of the copper smelting is described in Figure 1 (1,2).Outputs and raw materials treated in the last five years are shown in Table 2, in which concentrate includes powder copper scrap which amounts to 3 to 4% of concentrate.A full operation was performed for a period of one month, for both one flash furnace operation and for two flash furnace operation. With one furnace operation, 19,200 tons of copper were produced. With the two furnace operation, 84,000 tons of concentrates were charged and 33,500 tons of anode (net 28,600 tons of copper) were produced.The actual production level, however, has been kept at 80 to 90% of the full capacity because of low copper price, tight market of copper concentrate or fall of net demand in Japan."

Jan 1, 1989

By Erle C. Donaldson

Subsurface injection of liquid and slurry-type industrial waste is being used as a means of waste disposal. This survey conducted by the Bureau of Mines shows that the method can be economically and environmentally attractive if the proper precautions are taken, especially when the alternative is cursory treatment and discharge at the surface. Attention is called to petroleum technology and experience that can be applied to subsurface waste injection. Part 1 of this report is a discussion of the general aspects of subsurface waste-injection systems. Part 2 is a general discussion and review of the literature concerning the geologic formations available for injection in the United States. Part 3 is a discussion if 15 case histories including information on the source and nature of the waste and the geology, surface equipment, well completion, and operation of the systems.

Jan 1, 1974

By J. H. Rose

This paper describing the milling practice at the Magma Copper Co., Superior, Ariz., is one of a series being prepared by the Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to William Koerner, general manager of the Magma Copper Co., for permission to prepare this article; to J. S. Garrott, former mill superintendent, for the historical facts; and to Walter Cooksley, general foreman, for his assistance in obtaining the data.

Jan 1, 1930

By W. G. Jewitt

THE Box mine, situated in Saskatchewan on the north shore of lake Athabasca, is unique in two respects. It is the first and, so far, the only gold mine in Saskatchewan, and it is the only gold mine in Canada to employ a large-scale forced caving system as the main mining method. Discovered in 1934 by Tom Box, an Edmonton prospector, its subsequent history, while breaking no records for speed, has been one of steady and more or less normal development. Camp and plant are situated close to the shore of Beaverlodge bay, sorne 50 miles east of the Saskatchewan-Alberta boundary and 35 miles south of the north boundary of the Province. The railhead at Waterways, Alberta, is about 220 miles to the southwest. Prince Albert lies some 450 miles to the south. The surrounding country presents a rather rugged variation of the usual Precambrian topography, with hills rising five to six hundred feet above lake Athabasca. The numerous lakes and islands, together with the wide expanse of lake Athabasca, compose an attractive scene, at least in the not over-long 'open water' season. The winters are long but not extremely cold, judged by prairie standards. The small lakes break-up around May 20th and the 'freeze-up' stops navigation early in October. Though apparently remote, the Box mine is fortunate in having reason-ably cheap transportation from Edmonton. The 300-mile railway from Edmonton to Waterways is the most expensive section, the rate for 1st class freight being $1.70 per hundred pounds and for 5th class freight $0.77 per hundred. Freight from Waterways to the mine, approximately 140 miles down the Athabasca river and 90 miles along lake Athabasca, is delivered by barges and tugs for 50 cents per hundred pounds. All freight is delivered during the 'open water' shipping season, which lasts from about .Tune 7th to October 7th. In normal years, barges are loaded to 3 to 3 1/2feet draught up to September 1st. After that date, and earlier in dry years, shallow water at Waterways reduces the barge loads. Barges of 100 to 200 tons capacity handle all mining freight, including pieces up to 15 tons in weight, without undue difficulty.

Jan 1, 1940

By Paul M. Tyler

The outstanding trend in the graphite market is the fast-growing demand for cheaper qualities of graphite and the declining consumption of the more expensive varieties. The manufacture of graphite, crucibles for melting metals was one of the earliest applications of the-mineral and for many years constituted by far the leading source of demand. In later, years, however; and more especially since the Great War, the increasing demand for high-grade steel ingots and castings instead of enlarging crucible sales has permanently curtailed the domestic demand for crucibles because it has hastened the introduction of electric, oil or gas fired furnaces to replace the older types requiring pots to hold the metal during melting. While there has been a substantial increase in the use of graphite for miscellaneous refractories the total consumption for such purposes is too small to offset the shrinkage in demand for crucible making, and though it consumes the better and hence more expensive grades of crystalline flake graphite, it does not call so insistently for the still costlier Ceylon grades.

Jan 1, 1929

This volume constitutes the final report for the Rescue Subsystem portion of the Coal Mine Rescue and Survival System program conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated Jung 17, 1970). The program was directed by the Special Systems Department of the Westinghouse, Baltimore, Maryland facility. The basic objectives of the CMRSS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major- sources: the Request for Proposal from the Bureau of Mines and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering (NAE).

Jan 1, 1971

By Forrest T. Moyer

Quarry accidents in 1963 caused 61 fatal and 3,468 nonfatal injuries which occurred at respective frequency rates of 0.31 and 17.91 per million man-hours of worktime. The fatality record in 1963 was better than in 1962 but was appreciably worse than in 1.961. For nonfatal injuries, the 1963 record was slightly worse than in 1962 but was better than in 1961. The injury--severity rate of 2,913 days lost or charged per million man-hours in 1963 was better than that of 3,046 in 1962, the first year for which such data became available. The average severity of all injuries in 1963 was 160 days lost or charged per injury, 15 less than in 1962. An average of 91,960 men were at work on active days in 1963 and these men had an aggregate worktime of 193.7 million man-hours during the year.

Jan 1, 1972

By Rajesh Kumar Mishra

About 500,000 troy ounces of Platinum Group Metals (PGM) will be available for recycling each year from spent automobile catalytic converters in North America alone. Platinum Group Metals? from spent catalyst can be extracted by Hydrometallurgical, Pyrometallurgical or Gas Phase volatilization processes. This paper is a review and comparative study of various processes investigated for PGM extraction. A number of processes described in this paper have already been commercialized. The technical and environmental aspects of the important processes are discussed.

Jan 1, 1989

By Eddy Dierckx

Modernization of flat rolling plants is essential to sustainably fulfill increasing market demands and to improve competitiveness. Intelligent modernizations ensure getting maximum prime yield of existing mills, even if they have gone through half a century of operation. Existing mills were designed based on former production, consumption and quality targets. Ever increasing requirements such as increase of productivity, change of product mix (e.g. new steel grades), reduction of energy consumption and improvement of product quality lead to the necessity to adapt the existing equipment to the new target. SMS group provides, besides the reliable equipment and automation solutions to successful upgrades of existing mills, also a systematic approach to develop technical and economical solutions together with our customers (conceptual engineering). This paper describes the SMS group approach to modernizations / upgrades, introduces powerful performance modules and provides a number of successful examples that have been implemented recently.

Aug 17, 2017