Search Documents

By J. H. Holden, G. R. Strimbeck, L. F. Willmott, W. R. Huff

A pilot - scale fluidized feeder was developed for continuously feeding up to 1 ton of pulverized coal per hour to a pressure gasifier . Fluidization in the 3 - foot - diameter by 34-1 / 2 - foot - high feeder is effected by two streams of inert gas , a technique called zone fluidization . A stream of inert gas through a drilled plate in the base of a central column near the bottom of the feeder fluidizes the coal . Another stream through a drilled plate in the annulus between the central column and feeder wall provides a source of semifluidized coal for the central column . Fluidized coal from the central column discharges through an extraction funnel and discharge line . Zone fluidization provided good fluidization with moderate requirement for fluidizing gas . Instruments were developed for metering and recording the flow rate of fluidized coal . A system was developed for storing , and weighing pulverized coal , and then delivering it in fluidized form at about 1 to 8 tons per hour .

Jan 1, 1964

By B. van Beek, J. H. Zietsman, A. Lexmond, N. J. Andrew

"In platinum group metals (PGMs) smelting, the slag-to-matte ratios are very high (approximately 4:1 to 9:1). The slag temperature therefore has a strong influence on matte temperature, which is a continual concern due to the low matte melting temperature and its resultant high superheat. Maintaining a stable slag temperature is therefore a critical safety and operational issue. This project aims to improve the understanding of the slag bath temperature drivers so that a more effective slag bath temperature control strategy can be implemented.With the aim of developing a multiphysics model of the furnace, extensive data analysis was performed to develop an in-depth understanding of the process before the start of modelling work. In this work, the effect of fluctuating furnace feed composition on slag temperature was examined. The results are based on equilibrium calculations using FactSage, implemented with ChemApp.A method was developed, using an equilibrium calculation at 25°C, to convert the available chemical assays to approximate mineralogical assays in order to determine the feed enthalpies. Actual 2013 furnace feed data was used and the average specific energy requirement to produce slag and matte at 1600°C was calculated to be 671 kWh/t concentrate. The furnace energy input was then kept constant, and it was found that the slag temperature varies significantly as a function of the feed composition. These results were compared to actual slag temperatures measured on site. It was found that close management of the furnace energy balance is important for maintaining a stable slag temperature."

Jan 1, 2014

By C. Eswaraiah

A drop weight tester (DWT) is designed and fabricated for the purpose of analyzing single particle impact breakage characteristics of different ores. The test results were evaluated through the breakage distributions of different size fractions at five different input energy levels. The breakage parameter, t10 (Narayanan, 1986) is used to represent the degree of size reduction, which is assumed to be representative of the breakage product size distribution obtained from single particle breakage. Representation of breakage distribution with this method consist one more breakage dependent parameter (a). To evaluate the impact breakage characteristic of different ores, a mathematical relationship was established to analyze the dependency of breakage parameters, t10 and a on specific input energy (EIS) or fracture energy (Tavares et al, 1998, Fandrich, 1998), specimen size (?) and Bond?s operating work index (WI0). Mathematical results developed gives adequate model for all ball mill modeling. It can be concluded that the drop weight test method is a useful and practical way of evaluating the impact strengths of various ores and results of which can be used in modeling mills.

Sep 1, 2012

By M. J. Merwin

Heat treated seamless tubular products are processed in a fashion that can be easily modified to produce dual phase microstructures, through the implementation of intercritical soaking prior to quenching. Dual phase steels are known to possess low yield strength compared to tensile strength. The steel line pipe market is interested in low yield-tensile ratio materials for application in reel barge pipe laying operations. In the current work compositions of commercially produced material already in use for the line pipe market were examined and dual phase microstructures were successfully developed. The microstructure and properties of the materials were found to be stable over the range of intercritical temperatures employed. Tempering temperature and, somewhat unexpectedly, small chemistry differences were found to have the largest influence on properties. Excellent toughness performance was observed in samples tempered at temperatures in excess of 550°C. Tempering in this temperature regime produced materials with strength suitable for application as API X60 line pipe. A difference in tensile strength between steels of similar chemistry was observed, and is not fully understood at this time. Welding performance was considered through simulation of three regions of the heat-affected zone. Neither intercritical temperature, nor tempering temperature, were found to have a significant influence on the heat-affected zone properties. The peak temperature achieved in the thermal cycle was the only significant factor. The hardness of the heat-affected zone was found to increase continuously with increasing peak temperature. While toughness was found to be low for both partially-transformed and coarse-grain heat-affected zones, the toughness of the fine-grained heat-affected zone was substantially better. Based on the results found in this laboratory study, a limited production trial is expected.

Jan 1, 2005

By Derek V. Ellis, Jack L. Littlepage

"Marine ecosystem effects ar1smg from the discharge of man-generated wastes to the sea can be schematized as: acute poisoning, chronic poisoning, enrichment, suffocation, temperature effects, salinity effects, toxin bio-concentration, changed production rates and changed species equilibria. A professionally designed site-specific monitoring program to check for such effects can not only safeguard the marine ecosystem from degradation, but it can also protect the industry involved from unanticipated remedial action after expensive construction has been undertaken. Monitoring programs should consist of three steps. Step 1 is an ecosystem survey which should be undertaken prior to final design of the discharge system and submission of applications for permission to discharge, because there can be considerable cost savings in obtaining information at an early stage in development. Step 2 involves location of the effluent field at the time of starting discharge, and analysing its dispersal behaviour. Step 3 consists of ecosystem monitoring with sampling stations and specific tests based on the accumulated prior information."

Jan 1, 1972

By Keats, J. L.

IN THE literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical charac- teristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete as data possible on all the factors that affect the elimination of metalloids were obtained.

Jan 1, 1957

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

Traditional refractory materials for blast furnace hearth lining are mainly composed of carbon bricks and the ceramic cup. However, these materials can’t meet the demands for long service life design of blast furnaces. In this paper, a new refractory called carbon composite brick (CCB) was introduced, which combined the advantages of carbon bricks and the ceramic cup. In this case, the resistance of the CCB against corrosion was equal to the ceramic cup and the thermal conductivity of the CCB was equal to carbon bricks. From the results of more than 20 blast furnaces, the CCB could be well used in small blast furnaces and large blast furnaces. In the bad condition of low grade burden and high smelting intensity, the CCB gave full play to the role of cooling system, and effectively resisted the erosion of hot metal to improve the service life of blast furnaces.

Jan 1, 2015

By F. L. Wideman

This paper lists resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizons, an area comprising approximately 522,600 square miles, Sources of sulfur occuring within the region are sulfur are, pyrite and pyritic ores, and natural gases and petroleum. Data concerning these sources are presented on a statewide basis. Some of the known deposits of sulfur ore are surficial and of fumerole origin; other deposits have resulted from oxidation of pyrite or sulfide ores of copper, lead, and zinc. The deposits are small and the sulfur is distributed erratically in them. There is a small production from some of the deposits, and the material produced is used as soil conditioner.

Jan 1, 1957

By Ernest W. Johnson, F. E. Cash

"INTRODUCTION Mine operators have long realized the importance of providing a satisfactory and dependable means of giving prompt warning to underground mine workers at the occurrence of a mine fire or other threatened disaster.Most underground mines of the Lake Superior district are prepared to inject a stench liquid into the compressed-air system quickly to give such warning. The liquid evaporates quickly and gives off an intense and easily recognizable odor even when present in minute quantities in the mine air. Workers in the mines studied have been fairly generally familiarized with the odor and instructed as to evacuation procedure when the warning odor is detected.In some mines provided throughout with electric lighting, including working faces, a prearranged light-flashing signal is given as a warning supplementary to that received from the stench.In a few mines, workers have been instructed to evacuate the mine immediately in the event the compressed-air supply is cut off, regardless of whether mechanical failure may be involved.Information obtained in observing a number of stench-injection tests is compiled and presented in the hope-that it will serve as an incentive to provide means of making stench injections at mines not now so equipped and for making similar tests at other underground mines, so that in case unsatisfactory results are obtained rectifying adjustments or changes may be made in time. It is further hoped that this paper will bring out the real importance of repeating these tests from time to time, at least once a year on each operating shift, so that in the event of an actual emergency, underground employees will receive a prompt warning."

Nov 1, 1945

By A. Boeing

Rock-breaker automation and remote operation improves the safety and efficiency of mining operations. This article presents an overview of the Rocklogic rock-breaker automation system architecture that provides collision avoidance, automated parking, and remote operation functionality. The system consists of a distributed computer control system that interfaces with sensors attached to the rock-breaker, the rock-breaker hydraulics, and the site infrastructure. We present results of an automated Transmin rockbreaker installed in a production environment at an underground Australian mine site. The system has been in production use for over 900 days during which there have been no reported collisions, and 100% adoption of the remote operation technology. As a result, Rocklogic has significantly improved the safety of rock-breaking operations and reduced the rock-breaking cycle time, thereby improving the sites overall throughput.

Aug 1, 2013

By M. J. Ferrante

The standard enthalpy of formation, low-temperature heat capacities, and enthalpy increments above 298 K were determined by the Federal Bureau of Mines for synthetic dawsonite [NaA1C03(OH)21. The enthalpy of formation was determined by hydrochloric acid solution calorimetry, with the result ?Hf°298 = -469.4±0.7 kcal/mole. The low-temperature heat capacities were determined from 6 to 307 K by adiabatic calorimetry. Tabulated are low-temperature values of Cp°, S°, and H.-Ho° from 3 to 298 K. The derived entropy at 298 K is S298 = 31.55±0.3 cal/deg mole. Enthalpy increments above 298 K were obtained by copper-block drop calorimetry. Tabular data of Cp°, S°, H°-H°298, -(G°-H°298)/T, ?Hf°, ?Gf°, and log Kf are given from 298 to 477 K. Enthalpies and Gibbs energies of decomposition are also reported.

Jan 1, 1976

By Louis A. Turnbull

An investigation of coal deposits near Cerrillos Santa Fe County, N. Mex., was undertaken 14 the Bureau of Mines in 1943 as part of a general program to determine sources of metallurgical coal for western steel plants. Almost all of the coal used for metallurgical purposes west of the Continental Divide Is mined from the Lower Sunnyside bed in, Carbon County,, Utah. Coke used in western steel plants that is produced from Lower Sunnyside a coal is weaker, structurally, than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality then the coal produced from the Sunnyside bed. The objective of investigations of western coals was to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed. and (b) develop; if possible, reserves of coal with coking quantities superior to those of Lower Sunnyside

Jan 1, 1951

By Nathan Painter, Kevin Andrews, Andrew Karpa

Groundwater flow in bedrock units is an important factor to be considered for most mining situations, both underground and open pit excavations. Characterization of the hydrogeologic system into which a mine will advance is an important factor for slope and entry stability, mine dewatering design, and potential environmental considerations including stream loss and water well damage. In addition, hydrogeologic characterization of bedrock is important for locating water wells and for groundwater contamination mitigation. Hydrogeologic characterization for a site begins with a desktop study and often evolves to include drilling, geologic logging, monitoring well installation, groundwater sampling, pump testing, and packer (Lugeon) testing. In addition to these methods of hydrogeologic data collection, downhole geophysical logging of exploration and monitoring well boreholes provides detailed information associated specifically with in-situ conditions of each hole. The basic suite of geophysical logging tools used for hydrogeologic characterization often includes Optical or Acoustic Televiewer (O/ATV), full wave sonic, gamma-density, fluid temperature, resistivity, specific conductance, and flowmeter. For many hydrogeologic settings, groundwater flow in the bedrock is dominated by discontinuities, or fractures, in the rock. O/ATV logging allows for determination of the frequency (clustering), orientation, and aperture width of in-situ fractures, while sonic logging allows for estimation of intact rock strength. Fluid temperature logging and flowmeter measurements provide insight with regard to potential groundwater inflow zones, and other tools provide information for geologic unit contacts. This paper outlines the process and benefits of using downhole geophysical logging for hydrogeologic characterization and provides generalized examples from industry experience.

By Leonardo Araújo Peruch, José Fagundes, Henrique Carneiro Pinto, Marco Túlio Costa, Nayara Coutinho, José Fabiano Martins Assunção

The objective of this project was to increase the hot charge by reducing reheating energy consumption and raising the productivity of ArceloMittal Tubarão's hot strip mill by changing the HSM’s schedule process with optimization of the relocation process of slabs after HSM’s chance with focus on slab temperature in reheating time. The project began with the revision of metallurgical rules for the relocation of materials, definition of criteria temperature setting (hot / cold), definition of restrictions of the process and review of modus operandi scheduling process. With the implementation of the process / system it is expected to achieve a 10% increase in the hot charge index in slabs reheating furnaces and increase productivity of the ArcelorMittal Tubarão hot strip mill

Oct 3, 2019

By P. Meyers, F. DeSilva, L. Gottlieb

A number of tests looking at lead removal using ion exchange resins of various types from various aqueous streams have been undertaken. The tests focused on strong acid cation (SAC) and weak acid cation 0N AC) resins. It was found that the mechanism of lead removal is partly by lead filtration rather than solely by ion exchange in a large portion of the applications studied. This is not surprising since lead carbonate is essentially insoluble and almost all water supplies contain at least some carbonate alkalinity. Regeneration of lead from exhausted resins containing significant amounts of lead may not be practical in some cases because of the large chemical and waste volumes involved. Since lead, .·along with many other very insoluble metals, is often present as a suspended solid rather than in ionic form, ion exchange is probably not always the best technology for bulk lead removal.

Jan 1, 2000

By Jerry W. Ramsey

The Bureau of Mines studied two Pennsylvania anthracites using low-temperature carbon dioxide adsorption. A modified form of the Brunauer-Emmett-Teller equation was used to calculate specific surface areas. Two mesh sizes of each anthracite were used to determine how gamma irradiation at 106 and 108 rads, both in vacuum and in the presence of air, affected the carbon dioxide surface areas. Results show that anthracites have a system of pores that are essentially all interconnected rather than isolated; that anthracites differ from one another in specific surface, which may correlate with density; and that irradiation in vacuum has no discernible effect on specific surface of anthracite, but irradiation in air does produce changes in specific surface.

Jan 1, 1966

By Corale L. Brierley

Accumulations of microorganisms in the in-situ leaching environment are believed responsible for plugging of the orebody and thus decreasing uranium extraction. To assess the contribution of microbial growth to this problem, packed columns of ore and core specimens were leached in the laboratory. Samples collected at four in-situ uranium mining operations revealed pseudomonads, xanthomonads, Bacillus sp. and Micrococcus sp. in numbers of 105 cfu/ml. These microorganisms, inoculated into simulated leaching conditions, decreased permeability in two uranium ores by one order of magnitude in 20 days. Hydrogen peroxide (0.2 g/l) alleviated microbial plugging in the laboratory. Periodic injection of hydrogen peroxide through the production well into the orebody may reduce microbial plugging problems in the field.

Jan 1, 1982

By K. Kiangi

On installing the Metso Superior MK 54x75? primary gyratory crusher in Nkomati mine the crusher experienced severe power spikes greater than 1000kW which subsequently led to the crusher tripping under load while processing some of Nkomati?s MMZ ores. Likewise significant losses in throughput were also experienced while processing some of Nkomati?s MMZ ore types. Interestingly the crusher was capable of processing the PCMZ ores without experiencing any power spikes or losses in throughput. Investigations into the challenges faced by the crusher while processing Nkomati?s MMZ ores were conducted using the DEM model in conjunction with the fast breakage model present in Metso?s High Fidelity Simulator. The intentions of the study were to establish the most suitable operating conditions or cavity design that would potentially enhance the performance of the crusher. Likewise an understanding of the effects the feed conditions (size distribution and hardness) had on the crusher?s performance was established. Ore characterization tests were conducted on Nkomati?sPyroxenite, Diabase, Calc silicate and quartzite ores which were from Nkomati?s MMZ ore body. The ore characterization tests conducted were drop weight tests, slow compression tests and elastic modulus tests. Four simulations were conducted used the existing cavity design with various open side settings (OSS) and throws. This established the effects of changing the crusher?s operating conditions on its performance. Four additional simulations were conducted on two cavity designs with reduced volumes. This established the effects of changing the crusher?s cavity design on the crusher?s performance. Thus through the simulations a better understandings of the impact of the crusher design, operating conditions and feed conditions on the crushers performance. Furthermore an analysis of the crusher?s performance was made which was used as a basis for comparisons with the base case simulation. Keywords: crusher, discrete element method, simulation, ore characterization

Sep 1, 2012

By R. A. Beall

Consumable-electrode arc melting is now accepted throughout the industry as the best method for producing ingots of zirconium, titanium, molybdenum, and their alloys. In addition, the technique is widely used in laboratories for fusing samples of such metals as hafnium, chromium, tantalum, columbium, and thorium. The production of consumable electrodes from these metals presents some rather difficult problems, the accepted industrial solution being the use of heavy powder-metallurgy-type presses. This paper summarizes information on fabrication of consumable electrodes by this and alternative means, such as sintering, nippling, and welding lightly pressed compacts of scrap metal. A possible saving of considerable capital investment is shown in the case of sintered compacts. The electrical circuit components of a pilot sintering unit are analyzed. INTRODUCTION The consumable-electrode arc-melting process has been accepted by most of the industry as the best method at present for producing high-quality pure or alloy in-got from sponge titanium or zirconium. This technique is not particularly new, having been patented by Von Bolton (l)3/ in 1909 for melting tantalum. However, it has been applied to industrial-scale operation only in the last few years. Among the important contributions to this technique are the work of Kroll (2) and Parke and Ham (3) and the work reported by the Office of Naval Research (4). The Bureau of Mines-has added considerably to the knowledge of this process (5-9).

Jan 1, 1956

By A Fern, A Hawkes, o, W Smith, K Mee

Serious Injury and Fatality (SIF) prevention remains a priority focus within high-risk industries sector. A major mining operation sought to strengthen their approach to the management of high-risk activities through an in-depth review of all historical incidents that had serious injury or fatality potential (SIFp) events (sometimes known as hi-potential events). The analysis found that the organisation invested a disproportionate level of resources, time and effort on low consequence incidents with a high proportion of SIFp incidents going under the radar. It was found that 76 per cent of SIFp incidents were rated in moderate or lower risk categories and conversely, almost half of those incidents with a ‘serious risk’ rating had little or no potential for a serious outcome. As a result of this project, the operation engaged in a renewed focus on critical risk management and enhanced its operating cadence in critical risk for the workforce. This included bow tie analysis, an update to critical risk standards and increased workforce engagement in the use of critical control verifications in the field. Data analytics with lead and lag indicators continue to provide senior leadership team and risk owners with an understanding of exposure for SIFp and control effectiveness. The audience will take away learnings from a real-world case study that provides data-driven insights of the human, local and organisational factors contributing to incidents with SIF potential. In addition, participants will understand the steps taken to categorise and analyse this incident data and the initiatives currently being implemented by the organisation as a result.

Apr 16, 2024