Search Documents

The character of alluvial gold deposits presents severe difficulties, and sometimes limitations, on the extent to which metallurgical efficiency can be measured. Very little monitoring of metallurgical performance is practised. An indication of performance is often extracted from the comparison of production to the estimate. This is a dubious practice. The recovery efficiency of conventional practices, viz sluices, tables and jigs, falls off sharply below 0.2 mm. Field evaluation procedures tend to simulate these conventional practices. Thus the presence of fine gold may not be detected, particularly if obscured by clay. There is increasing evidence that fine gold could, in places, be present in sufficient concentrations to be economic. Most gold in paleoplacers is finer than 0.1 mm. There are established practices elsewhere in the mineral industry that may physically recover gold down to 5 microns in size and which could find application for fine alluvial gold.

Jan 1, 1984

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By M A. Wells

The various mechanisms by which phosphorus (P) occurs and is distributed within banded iron formations (BIF)-derived iron ore are examined. In unenriched, precursor BIF P occurs predominantly as discrete grains of primary apatite. In high-grade ores hosted mainly by the Brockman Iron Formation, P occurs in three main forms:1. as secondary apatite;2. other submicron, P-rich phases (eg Rare earth containing minerals (REE), vivianite, strengite,wavellite) present in pore networks; and3. as P occurring with iron oxides, in particular, goethite.However, the presence of secondary P-bearing phases does not contribute signifi cantly to the total P level in iron ore, and it is P associated mainly with goethite, which represents the most common occurrence of P in these ores.No direct evidence for the replacement of Fe by P within the structure of synthetic goethite has been demonstrated. Therefore, it is most likely that in iron ores P associates with goethite in occluded form as adsorbed PO4 3- species or as discrete P-bearing minerals, such as strengite, wavellite or vivianite, in ultra-fine, micro-pores or within intra-domain regions of multi-domainic goethite. Such occluded P is not easily extracted with commonly used lixiviants, such as weakly alkaline leachates. Recent development of a low temperature-alkalie/water leach extraction method has been successful in reducing not only the P content, but also amounts of Si and Al inthe initial ore. Refi nement of such a method to commercial application will have enormous benefit in realising the economic potential of large tonnages of high-P (ie >0.07 wt per cent P) bearing iron ore.

Jul 11, 2011

By Irwan Halim, Stephane Polycarpe, Brian Hann

The Narragansett Bay Commission Phase III CSO Program includes construction of the 11,600-foot long, 30-foot ID, deep rock Pawtucket Tunnel in Rhode Island. This paper provides an overview of the Design Build Project features and highlight some of the important design considerations, features, and innovations, including geologic conditions and related TBM design, and deep shaft and tunnel segment designs. The paper provides the most recent updates on some of the project construction activities including TBM tunnel progress and retrieval schemes, tunnel pump station and deep vertical shaft liner installations, SEM construction, and microtunneling for the longest adit using Fiberglass Reinforced Polymer Mortar pipes.

Jun 23, 2024

By S Dykes, R J. McCarthy, B Klein

There is growing interest in the mining industry on the application of ore sorting. While many are familiar with particle sorting, including the limitations that technology presents (e.g. throughput), bulk sorting, with its higher throughput potential, is less understood. Despite the potential to sort at higher throughputs, few operations have adopted bulk sorting processes, certainly not at large scale. It is suggested that the inability to reliably predict outcomes from bulk sorting may be limiting its adoption in mining projects. Consequently, an evaluation approach for bulk ore sorting has been developed such that mass pulls and grade upgrades can be predicted in the context of a mining study. The approach allows for evaluation of drill core assays and application of the consequently derived heterogeneity relationships to the block model for estimation of sorting outcomes. These processes were applied to conveyor-based bulk sorting for the CuMo project in Idaho, USA and are described in this paper.

Nov 10, 2020

By Roberto Galéry, Braz J. C. Filho, Marcelo M. Stopa, Douglas B. Mazzinghy, Priscila M. Esteves

"The purpose of the research is to monitor ball mill filling by means of signals usually measured in its electrical drive. The method is based on the mill torque estimated from rotor speed and induction motor stator voltage and currents. New signal processing is presented in both time and frequency domain for measurements in a dry laboratory ball mill. Statistical analysis is applied to time series resulting in good correlation to mill filling. Fast Fourier Transform (FFT) and power spectral density (PSD) also resulted in an accurate filling indicator. The proposed method does not need any sensor to be installed directly on the mill and requires only sensors usually available for motor control purposes. The experimental results showed that the method have potential to be used to construct an automatic system for monitoring operational variables in ball mills. The aim of this monitoring is to improve energy efficiency, reliability and productivity.INTRODUCTION Recently, a great number of papers have pointed the importance of ball mill filling monitoring and also of grinding control (Lu, et al., 2014) (Ramasamy, et al., 2005) (Tsamatsoulis, 2014) (Zhou, et al., 2009). Additionally, great amount of control techniques have also been presented with several complexity degrees (Tsamatsoulis, 2014). According to Eremenko (2015) the lack of effective and accurate methods for fill level measurement is the main reason that makes mill optimal control so complicated. It happens because nonlinearity, long time delay and time varying features of the ball mill turns difficult to develop a truly efficient method for monitoring filling. At the same time, fill level has a determining role in charge motion and consequently on particle breakage. For low levels of filling many energy is expended in impacts with very low breakage efficiency. Those impacts can also damage mill liner. In contrast, high levels of filling causes damping effects that reduces breakage and can also affect energy consumption. Based on this it is conclusive that fill level measurement of ball mills is an important issue for grinding efficiency. This fill level information can be used for operators to control ball mills and also for engineers to run simulations and improve confidence levels of circuit designs (Shi, 2016)."

Jan 1, 2018

By F. C. Hull

The grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. Usual Methods OF EvaluatiNg Grain Size A frequetly used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.—The Metals Handbook' has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.—Idealized grain.boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E 19 - 39 T, standard Micrographs & Metals Handbook and ASTM Tentative Standard E19-3gT contain micrographs of hypo-eutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diameter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying. grain size in ASTM Tentative Standard E 2-39 T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries' method for grain-size measurements consists of counting the number

Jan 1, 1948

By F. C. Hull

The grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. Usual Methods OF EvaluatiNg Grain Size A frequetly used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.—The Metals Handbook' has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.—Idealized grain.boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E 19 - 39 T, standard Micrographs & Metals Handbook and ASTM Tentative Standard E19-3gT contain micrographs of hypo-eutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diameter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying. grain size in ASTM Tentative Standard E 2-39 T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries' method for grain-size measurements consists of counting the number

Jan 1, 1948

By Henry M. Harris

Low-carbon shales from 65 deposits and 11 sources of coal-mine waste in western Oregon and Washington were tested in a rotary kiln for their suitability as raw material for expanded aggregate. Shales from 41 sources bloated enough to produce crushed, expanded aggregates, weighing less than 65 pounds per cubic foot in the preliminary tests. The samples were judged on the basis of processing qualities, physical properties, and size and uniformity of the source. Nine low-carbon shale deposits and three coal-mine waste sources were selected for more extensive bloating tests and for examination of the expanded aggregates in concrete shapes. Composite samples from these 12 sources and from 2 commercial operations, when processed for testing in concrete shapes, had bulk densities ranging from 37.S to 72.9 pounds per cubic foot. Damp-cured concrete shapes made with these aggregates had bulk densities ranging from S6 to 119 pounds per cubic foot, and all but three of the lightweight concretes had crushing strengths ranging from 3,270 to 6,810 p.s.i. Properties of the lightweight concretes were compared with those of concrete shapes made with commercial aggregates, and with sand and gravel.

Jan 1, 1962

By Resta S. A

Energy Resources of Australia Ltd - Ranger Mine is located about 255 kilometres east of Darwin in the Alligator Rivers Region of the Northern Territory. The Ranger project is surrounded by Kakadu National Park which is on the UNESCO World Heritage list. . Ranger Mine operates the largest uranium mine and processing plant in Australia. It is designed to produce 3000 tonnes of uranium oxide per year, but presently is producing a little less than one half that figure due to the depressed uranium market. The safety performance of the employees and Ranger as a whole continues to improve. The lost time injuries (LTI) have significantly reduced from 74 in 1985 to five in 1994. The total days lost due to LTIs have gone from 1543 to 14. These significant improvements have reflected directly on workers' compensation premiums in which a four-fold reduction has occurred. It is estimated that the actual monetary saving to the company is about $1.3 million per year and directly reports to the profit of the company. There is also an obvious and significant reduction in the less quantifiable costs such as the suffering of the injured employees and cost to society. The paper will review the various initiatives introduced and assess their effectiveness. Performance improvement is primarily dependent on the commitment, introduction of various initiatives and the subsequent change in workplace culture.

Jan 1, 1994

By R. E. Lindstrom

The mineral bastnasite is utilized to describe alternate processes for the extraction and separation of the rare-earth elements by solvent extraction. The rare earths can be acid-leached directly or fused with NaOH before acid leaching. Cerium, the major constituent, can be recovered by fractional precipitation, fractional leaching, or solvent extraction with tri-nbutyl phosphate. The latter process is capable of producing 99.5-percent pure CeO2 at 98+ percent recovery. Lanthanum is subsequently recovered by fractional precipitation or solvent extraction with a nitrogen-based extractant. A 20-stage mixer-settler operation with a primary amine extractant results in a 95-percent pure La203 fraction at 96 percent recovery. Europium is amenable to extraction from most of the remaining rare earths with an organophosphate extractant. Selective stripping of the europium, followed by reductive precipitation, produces high-purity Eu203. Another possibility for europium purification involves the differential extraction of europium with an amine followed by a sub- sequent reducing strip. Separation of the remaining elements is more difficult but can be accomplished with amine or quaternary ammonium extracts. Typical separation factors achieved are 3. 8 for praseodymium-neodymium and 10. 5 for neodymium-samarium.

Jan 1, 1967

By E. W. Davis

DURING late years, the proportion of beileficiated iron ore shipped from the Lake Superior District has increased very rapidly. By benefication is meant washing, screening, drying, sintering or any process by which the grade or structure of the crude ore is improved before shipment. In 1915, only 3,000,- 000 tons, or 9 per cent, of t6e total Minnesota shipment was beneficiated ore, compared with 13,500,000 tons, or 35 per cent, of the total Minnesota shipment in 1925. This increase is, of course, due to the fact that iron and steel can be made more cheaply after beneficiating these ores than they could have been had these ores not been so treated. Fundamentally, however, several causes contribute to the necessity for beneficiating iron ores, such as depletion of the reserves of high-grade ores, the iron ore leasing systems and taxation methods and, at the smelting plants, a better understanding of blast-furnace operations, increased operating costs and increased sulfur content of blast-furnace coke. As economic conditions change, it is by no means certain that the proportion of beneficiated ore shipped each year is going to continue to increase. Undoubtedly some of the beneficiation operations are not economically sound at the present time and what the future has in store for the iron ore industry is problematical. Generally speaking, the cost of fuel for blast-furnace operations will increase as time goes on and in order to continue to produce cheap iron and steel, some of the other costs must be lowered. Freight and labor rates probably can- not be reduced. The cost of producing iron ore cannot be reduced much below the present price. It therefore appears that the best opportunity for maintaining iron and steel prices at their present level in spite of in- creased costs of labor and raw materials is to use. less or cheaper raw materials. This, of course, contemplates an improvement in metallurgical processes all along the line and, as a matter of fact, we can confidently expect these improvements because scientific investigations will undoubtedly be even more productive in the future than they have been in the past.

Jan 1, 1926

By Fabien Miller

Automation technologies are increasingly envisaged to improve underground mining productivity. However, the technologies need to be used and adopted gradually in order to get the best benefits. This paper presents the technical and operational aspects of autoguided production vehicles at Brunswick Mine. During 2001 Noranda?s Brunswick Mine has successfully commissioned an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two orepasses. Operational advantages include increased system capacity and enhanced safety and comfort for the operator. The data obtained up to now indicate that the system can operate reliably in mine production

May 1, 2002

By E. DeGolyer

USE of geophysical methods as an aid to prospecting for new oil pools and in the exploration of already discovered pools continued to increase and reached a new high during 1934. As in previous years, the scene of greatest activity was the Gulf coastal plain of Texas and Louisiana. Seismic crews working by the reflection method increased from some thirty crews at the first of the year to forty crews at the end. An increased demand for torsion balance work at the beginning of the year occurred and practically all available instruments were put into service. Some thirty crews with approximately eighty balances continued throughout the year. Both the pendulum and gravimeter methods of gravity surveys registered their initial successes and equipment was increased from five to seven pendulums and from one to three gravimeters during the year. Approximately five magnetometer parties continued to work throughout the year. No surface surveys by the electrical method are known to have been made. Outside of coastal Texas and Louisiana the chief geophysical work

Jan 1, 1935

By John B. Miles

THE present period of depression in the iron industry, with the resultant close approximation of the cost of production to the selling-price of pig-iron, should make the discussion of this subject at this time not only interesting but, profitable. It is possible that it may result, in the collection of data, which when added to those set forth in this paper will clearly indicate the influence of the rate. of driving a blast-furnace upon its fuel-economy. The question is not whether an excessive rate of driving (meaning a rate definitely in excess of the average rate in the United States) results in, an increase in the fuel-consumption, but rather whether a rate considerably less than the average does not result in a marked decrease in the fuel-consumption. The commercial and metallurgical sides of. this problem must be kept separate. With a large margin between the cost of production and the selling-price of pig-iron, and a plant already in operation, it is frequently profitable to sacrifice a couple of hundred pounds of fuel per ton of pig-iron in order to secure the greater gross profits resulting from a larger tonnage. When this margin decreases with a plant in operation, or when the determination of the size of a new furnace intended for a certain production . confronts the management, a clear understanding of the effect of the rate of driving upon fuel-economy becomes necessary. If it be granted that slow driving leads to low fuel-consumption, it should he borne in mind in the design of a new plant for the production of a certain tonnage that the adoption of an economical rate of driving increases only the size of the furnace proper, whereas, due to the decrease in quantity of blast required on account of the decrease in fuel burned, the stoves, the blowing-engines, the boilers and the piping may be de-

Sep 1, 1908

By H Zorychta

Based on underground measurements made at the Nova Scotia coal mines of the Dominion Coal Company, Limited, this paper presents a comparison between the physical properties of hardwood packs and steel friction props when used for longwall support. The probable loads sup-ported by steel friction props on a longwall face at both the Dominion No. 20 Colliery and the Princess Colliery are delineated, and the results of the tests are presented in graphical form. It is concluded that the steel friction props are more efficient than the hardwood packs that they replaced as roof supports. Introduction AN evolution in the methods of longwall face support is taking place in the Sydney coalfield. Longwall face support had consisted primarily of timber props and hardwood packs. In 1957, however, at the Princess Colliery, Sydney Mines, Nova Scotia, the first longwall was equipped with steel friction props. At the present time, eleven longwall faces are supported on wood and sixteen faces are carried on steel friction props.

Jan 1, 1965

By R. L. Montgomery

The literature has been surveyed and values recalculated for the heats and free energies of formation of solid rare-earth compounds at 298° K. In most instances it was necessary to estimate the entropies. Thermodynamic properties of aqueous rare-earth ions have also been calculated. INTRODUCTION The accumulation of thermochemical data on rare-earth compounds in recent years makes it possible to review the subject and to obtain more consistent and more reliable information than was available previously.

Jan 1, 1959

By D. Hu, L. Matzar, J. Hampton, M. Gutierrez

Nanodarcy permeability is common in many oil- and gas-bearing formations requiring unconventional stimulation technologies, such as hydraulic fracturing (HF), which can connect the isolated hydrocarbon-rich pores with a wellbore through induced fracture networks. Even though a dense induced fracture network is capable of accessing economic amounts of hydrocarbons, much of the rock between and very close to the fracture network is still un-accessed and contains extremely low permeability. Inducing fracture networks into brittle rock can create large amounts of micro failures in surrounding regions that are not connected to the wellbore, as can be seen in Fig. 1(a) from the very wide acoustic emissions (AEs) cloud associated with a narrow fracture generation. It is possible in certain types of rock to increase the effective matrix permeability in localized regions based on the damage associated with the surrounding hydraulic fractures and subsequent high stress concentrations along localized pre-existing potential failure zones. To study this problem, laboratory HF tests were performed at true-triaxial stress state in brittle crystalline rock while monitoring AEs. The AE associated with HF was analyzed for source parameters using the moment tensor inversion method called Simplified Green’s Functions for Moment Tensor Analysis (SiGMA). Using the moment tensor for each individual AE event, the mode of failure was determined. Crack slip directions and crack face normal directions were also found, along with the relative volume of individual micro failures as well as a damage parameter. The associated source parameters were used to classify differing regions of damage in the sample induced from HF and correlate these regions of differing damage to the effective drainage region. Shown in Fig. 1(b) is a near-wellbore (NWB) region that contained three times larger average relative volumetric deformation of individual tensile AE events than the average tensile AE event volume from the entire sample. Because of the large difference in micro fracture volumetric deformation for the NWB region compared to the entire sample, predictions of HF induced damage must be included in reservoir drainage predictions.

Jan 1, 2015

By M. J. Dailey

This paper is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The property of the Silver King Coalition Mines Co. is situated in the western past of the Park City mining district, Utah, about 1 ½ miles southwest of the town of Park City, The elevation at the collar of the main shaft is 8,137 feet above sea-level.

Jan 1, 1930

By M. C. Manderson

Phosphate rock is a naturally occurring mineral which, in upgraded form, is important to both agriculture and industry. Phosphate rock normally must be upgraded before it can be assimilated and used. Most of this upgrading is now carried out by chemical means, largely through the reaction of a strong inorganic acid (primarily sulfuric acid) with the phosphate rock to remove major impurities and to produce soluble phosphate. A less important but yet still commercially significant conversion method involves the thermal reduction of phosphate rock at high temperature in an electric furnace to produce elemental phosphorus. The elemental phosphorus is then converted to usable end products. This conversion route is a more costly method than the chemical route, but it has the advantage of being able to produce chemically pure phosphorus derivatives. On the other hand, the use of phosphate rock for agricultural application-primarily for use as a plant nutrient ingredient for fertilizer -does not require the same level of purity. As a consequence, the chemical method of phosphate rock upgrading is the predominant technique for producing phosphatic fertilizers.

Jan 1, 1977