Search Documents

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of grinding conditions on galena flotation and galena separation from pyrite. The changes occurring on the mineral surface during grinding were investigated by EDTA extraction and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the type and amount of oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite flotation but had little effect on galena flotation. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled.Grinding conditions had a large effect on the flotation of the galena particles of different sizes. Flotation of fine galena particles (-10 µm) was depressed by iron oxidation species derived from the grinding media. Chromium grinding medium decreased the production of iron oxidation species and therefore increased the flotation of fine galena particles."

Jan 1, 2003

By Joseph T. Coe, Alireza Kordjazi, Michael Afanasiev

Cross-hole sonic logging (CSL) is a common quality assurance measure for the evaluation of the structural integrity of drilled shafts. The results of CSL can be supplemented by a set of tomographic images generated by cross-hole tomography (CT). Although the same access tubes, sources and receivers are used in both methods, CT has the advantage of providing a higher quality image of the possible anomalies in drilled shafts. Nevertheless, it has been reported in literature that the CSL and CT miss anomalies with sizes of smaller than 10 percent of the cross sectional area of the drilled shaft. This implies poor resolution despite the high-frequency of the stress waves utilized in these methods. This issue with resolution can be at least partially attributable to the fact that CT relies entirely on the inversion of the first time of arrival and ignores the information embedded in the rest of the recorded traces. This study examines the application of full waveform inversion (FWI) to generate a higher resolution image of the possible defects in drilled shafts from the same data used for cross-hole tomography. FWI is a wave-field method that aims to directly match the recorded traces with traces obtained from a numerical model of the domain. This has the benefit of avoiding the selection of the first time of arrival, along with increasing the resolution of the final image due to extracting more information out of the traces. Through a series of numerical simulations, synthetic traces were generated from a drilled shaft with defects of known mechanical properties, dimensions, and location. These traces were then inverted to evaluate the performance of FWI for structural integrity testing of the drilled shafts. INTRODUCTION The presence of construction defects can compromise the structural integrity of drilled shafts and negatively affect their performance (O’Neil 1991; Sarhan et al. 2002; O’Neil et al. 2003; Poulos 2005). Several non- destructive testing (NDT) methods exist that are currently used for the evaluation of the structural integrity of drilled shafts. Cross-hole sonic logging (CSL), cross-hole sonic tomography (CT), and thermal integrity profiling (TIP) are well-established and documented in the industry and practical manuals (Brown et al. 2010). NDT methods prevent the need for coring and excavation and are relatively fast and cost effective. Successful implementation of these techniques has also been reported in the literature (Branagan et al. 2000; Iskander et al. 2001; Mullin 2010; Johnson 2016).

Jan 1, 2019

By AIME AIME

WEDNESDAY night, by long tradition, is al- ways set aside for the annual dinner, even when, as it was this year, it is Ash Wednesday. Whether the somewhat smaller attendance than last year is attributable to that cause, the unexpectedly long persistence of business depression, or whatever may have been the reason, it was a joyous occasion, and the grand ball-room of the Commodore Hotel was as completely filled With diners as * was consistent with com- fort. In the half hour before the dinner was actually served the guests assembled in an adjoining room and not only exchanged greetings but proceeded along the receiving line to greet the guests of honor. The number present was so large that hardly more than half of them had been able to do this before the summons to the dining room sounded and a hearty and immediate response was made to it. Toy balloons at each plate, inflated and directed at the heads of companions or nearby friends, but which were just as likely to carom from the nose of a hurrying waiter, successfully broke the ice as well as not a few plates. It would be interesting to know whether the pleasure the guests derive from these de- vices is in part based on the all-too evident annoyance of the waiters, and what the relative quantitative relationships are.

Jan 1, 1931

By Shklyar FP, Babushkin NM, Bokovikov BA, Fedotov PB

A mathematical model for gas flow dynamics and heat and mass transfer processes occuring in the tuyere raceways and in the zone of the final for- mation and heating of pig iron and slag has been developed and simulated on a digital computer. It takes into account the formation and size of the raceway zones, combustion of coke and its substit- utes, oxidation of the metal, radiation from the gases to the raceway boundaries, physical heat losses and the direct reduction of the pig iron elements below the raceway zones. To evaluate the distribution of heat produced by the oxidation of metal between gases and prod- ucts of smelting, the problem of heating the mat- erials in the raceways with the sources of heat in the materials under conditions of intensive gas circulation in the raceways is solved. To determine the amount of heat transferred by radiation from the gas to the boundaries of the raceways, the problem of radiant heat transfer be- tween two grey bodies forming a closed system is solved. Using the structural parameters of the furn- ace, the inlet parameters of the combination blast and exit parameters of the melt, the model permits the calculation of the temperatures of materials entering and leaving the raceways and also the res- idual temperature of the gases, which qualitatively differs from the theoretical combustion temperature. Analysis of the operation of several different blast furnaces has shown that the overall picture of the interaction between gas flow dynamics, mass and heat transfer processes occuring in the race- ways and in the zone of final product formation, obtained with the aid of the model, now permits us to approach from a different position the deter- mination of the limiting factors in furnace operat- ion. It also allows us to explain certain phenom- ena observed in blast furnace practice and to dis- cover new relationships which may be used in analy- sis and control of the smelting process.

Jan 1, 1981

By İlknur Erol

The abstract highlights that hearing loss is an occupational disease caused by noise exposure in the workplace. The study investigates noise-induced hearing loss among miners in underground coal mines in Turkey, considering factors like occupation, age, and exposure time. The research employs logistic regression analysis to reveal the relationship between hearing loss and these factors. The findings suggest that occupational groups and duration of noise exposure significantly affect hearing loss. Miners in production groups and those exposed to noise for 10-14 years have a higher risk. The study concludes that age does not significantly increase the probability of hearing loss.

Mar 24, 2022

By B. G. Hunt, E. J. Kwasney, W. P. Campbell, S. L. Gertsman

"AbstractIn the separation of lead and zinc concentrates from the ore from Cominco's Sullivan mine at Kimberley, • B.C., an iron sulphide concentrate is also produced, some of which is roasted to provide sulphuric add for the manufacture of phosphate fertilizer. The iron oxide calcine from the roaster is potentially a valuable raw material for the production of pig iron and steel. To evaluate this material, six tons of .pig iron was produced from it in an experimental 75 k.w. electric furnace at Trail. The pig iron alone, and also in varying proportions with structural steel scrap and commercial pig iron, was used in the production of basic electric furnace steel at the Mines Branch Laboratories, Ottawa. Details are given of the steel making and fabrication procedure, of the visual and microscopic examination, and of the extensive series of tests on the steel produced. The steel produced using Cominco .pig iron in the charge showed normal working properties in all tests carried out.IntroductionTHIS PAPER describes (a) experimental work by The Consolidated Mining and Smelting Company of Canada, Limited ( Cominco), at Trail on the production of pig iron .from Sullivan iron concentrates, and (b) a joint laboratory investigation by Cominco and the Mines Branch, Department of Mines and Technical Surveys, Ottawa, to determine the feasibility of making a satisfactory steel from this pig iron."

Jan 1, 1955

By Jay J. Burns

TWO zinc concentrating mills are operated by the St. Joseph Lead Co. in St. Lawrence County, N. Y. The Edwards mill is operating at present only sixteen hours a day treating 400 tons daily. The metallurgy at Edwards presents no unusual problems therefore this discussion is mainly limited to the metallurgy of the Balmat ore. The Balmat mill has a capacity of 1,250 tons per day and the operating crew consists of three shift bosses each with five millmen per shift. Two crusher operators work on each of two shifts and one cleanup man on day shift. The repair crew is made up of a foreman and three repairmen, one of the repairmen being capable of taking over any operating job in the mill from shift boss down. Each millman is capable of handling the next job in line and several men in the yard crew are broken into handling the start-off job in the mill so that temporary shortages of men do not cause extensive overtime. Sphalerite, pyrite, and galena, the principal ore minerals, occur in a gangue of calcite, dolomite, and silicates, especially diopside, plus tremo-

Jan 1, 1947

By Y. Mudryk, D. Paudyal, K. A. Gschneidner, V. K. Pecharsky, M. Khan

"Rare earth intermetallic compounds are utilized commercially as magnetic and battery materials, electron gun electrodes, etc. Several of these intermetallics will be briefly discussed. There are many other rare earth intermetallic compounds which are not utilized industrially but have unusual properties which are of fundamental interest and may have future technological applications. Several of these materials are discussed as well.INTRODUCTIONTens of thousands of rare earth intermetallic compounds exist, but physical properties (primarily their magnetic behaviors), other than their crystal structures have been measured for only a small percentage of these materials. Among these are the commercially important compounds: Nd2Fe14B, and the SmCo5 – Sm2Co17 family – well known high strength permanent magnets; (Tb0.3Dy0.7)Fe2, Terfenol-D, a giant magnetostrictive material; LaNi5Hx a critical component of the rechargeable Ni metal hydride batteries; and LaB6 an electron emitter. There are, however, many other intermetallic compounds which are not utilized industrially, but none-the-less, exhibit interesting, and sometimes, exotic physical properties which are of fundamental interest and may have some future technological significance. These include: the giant magnetocaloric effect compounds Gd5Si2Ge2 and La(Fe13-xSix)Hy; the RCu and RAg families of ductile intermetallics; the mixed intra-lanthanide (R,R')Al2 compounds in which magnetic transitions disappear and reappear as one R is substituted for by R'; and GdNi which exhibits large dilations along two crystallographic directions and a larger contraction in the third direction at the Curie temperature resulting in zero volume change as GdNi orders magnetically via a second order phase transition.COMMERCIALLY IMPORTANT INTERMETALLICSNdFeB Permanent MagnetsThe Nd2Fe14B permanent magnets were discovered in 1984 independently in the USA and Japan. It is a ferromagnet and with proper heat treatment and processing Nd2Fe14B is the strongest near room temperature permanent magnetic material known today. This intermetallic compound is utilized as a permanent magnet in many applications, such as electric motors (e.g. the modern automobile contains up to 35 electric motors), spindles for computer hard disc drives, microphones and speaker magnets for cell phones and other audio equipment, direct drive wind turbines, actuators, and Magnetic Resonance Imaging (MRI) units. There are two kinds of NdFeB permanent magnets – bonded and sintered. The bonded magnets have a lower magnetic strength than the sintered magnet. The highest strength magnets are obtained by small substitutions of Dy (up to a maximum of 10%) for Nd, because Dy can significantly increase the coercivity and thus the energy product (a measure of the magnetic strength or hardness). The bonded magnets account for about 12% of the NdFeB market (~82 metric kt per year, containing ~20 kt/a of Nd). The NdFeB permanent magnet market is growing at a rate of about 15% per year. (Burzo & Kirchmayr, 1989; Kobayashi & Hirosawa, 2001; Coey, 2011)."

Jan 1, 2012

By E. H., Edwerd H. Robie

WILLIAM CHURCH was one of the founders and the first president of the Detroit Copper Mining Co. and was the first man to interest the Phelps Dodge company in the possibilities of the Morenci district, in the '70's. One rather interesting story concerning him is told by James Colquhoun, at one time president of the Arizona Copper Co., in his "History of the Clifton-Morenci Mining District." It seems that a geologist visited the Detroit company's mines and gave Alec McLean, then mine superintendent, quite a lesson on the proper mineralogical terms for what he saw in passing. Later, McLean handed out a few of them to Mr. Church as they walked through the mine on a tour of inspection. The latter had even less regard for a geologist than he did for sulphide ore, which meant little indeed, for in those days the rich ore was all oxidized, and there was no money in the sulphides. So Church was completely unimpressed by the geological and mineralogical terms that McLean had acquired from the visiting geologist. Church turned on him and warned him that so long as he was a member of his staff he was to understand that there were only two kinds of rock in his mines-the one was smelting ore and the other was waste rock, and he was not to forget it.

Jan 1, 1942

By S. A. G. Poppen, J. Konopka

"Petro-Canada's project investigative and experimental underground work in the Galt coal seam at Kipp, Alberta included the construction of an emergency egress and ventilation raise from surface.The Galt coal seam is 206 m below the surface and covered by 8 m of shale, sandstone and clay beds of the Oldman Formation, 128 m of shale, bentonite beds and sandstone of the Bearpaw Formation, and 70 m of glacial till and basal gravel. Free water was encountered from sand lenses in the glacial till and the basal gravel.Excavation for the ventilation raise was a nominal 2 m diameter and it was lined with a welded, continuous, steel liner of 1.2 m 1.D.Excavation in the glacial till was carried out with a surface bucket drill rig combined with hand mining. Ground support in the glacial till consisted of liner plates and backfill grout. The Bearpaw and Oldman formations were excavated by employing standard raise boring techniques. The individual liner sections of the continuous steel liner were assembled on surface and the entire liner column was lowered into the raise by employing hydraulic lift climbers. The liner column was back-filled with concrete.IntroductionThe Lethbridge Coal Field comprises an area of approximately 1 165 square km in the vicinity of Lethbridge in southern Alberta. Pacific Petroleums Ltd. proposed in a Preliminary Disclosure in January 1979 ""to open an experimental mine prior to development of a producing underground mine with an initial rate of 540,000 tonnes per year"". A 2 900-hectare group of leases in the Kipp-Coalhurst area was selected as the primary target for the Kipp experimental mine. The scope of work for the experimental mine included the construction of an access shaft with production capabilities, the construction of a ventilation and emergency exit raise, drive-ages in coal to yield a bulk sample, gathering of geotechnical information and the testing of experimental mining methods."

Jan 1, 1983

By Harold V. Pearce

(Chattanooga Meeting, October, 1908.) THE fire which occurred in the fall of 1906, at the works of the Boston & Colorado Smelting Co., Argo, Colo., destroyed entirely the gold- and silver-refinery of the plant; and in view of the development of modern practice in the refining of copper-mattes, etc., the management decided that it would be inadvisable to rebuild that part of the works for the continued use of the process which had been conducted therein for so many years as a metallurgical secret. This decision probably removes altogether from the sphere of practice the " Pearce " method for the separation of gold. At all events, it removes the business reasons which have prevented hitherto the publication of the principles involved. At the suggestion of Dr. Raymond, Secretary of the Institute, my father, Richard Pearce, the former manager of these works, has requested me to prepare a brief description of this process for the benefit of our members. Since I severed my connection with the Boston & Colorado Smelting Co. some time ago, I am indebted for some practical details to the present superintendent, Charles Rees, whose friendly assistance I would gratefully acknowledge. With regard to the history of the inception and development of this process by its inventor, Richard Pearce, I cannot do better than quote freely from his own notes and papers. HISTORY OF THE PEARCE PROCESS.' "In 1874 my entire time was directed to the improvements and additions to the plant at Black Hawk. The changes which I had made in the construction of the furnaces at Black Hawk proved so beneficial that I was requested to introduce the improvements at the branch works at Alma. These changes were carried out as speedily as possible, and proved of great advantage as compared with the old system. "The separation and refining of the gold from the matte now engaged my attention, and since previous experience in the treatment of gold-bearing matte and

Feb 1, 1909

By Russell Frith

The entire subject area of micro-seismic events due to stored strain energy, as distinct from gas-driven coal outbursts, can be readily sub-divided into firstly events with their energy source from within the coal seam (termed “bursts”) and secondly, event with their energy source outside of the coal seam in either the overburden and/or floor strata. The reason for sub-dividing micro-seismic events in this manner is that if the causation mechanisms and associated geotechnical conditions are materially different, then effective pre-mining predictions and subsequent operational controls may also differ. Attempting to explain a multitude of micro-seismic event types without consideration of varying source mechanisms will inevitably lead to inadequate causal explanations and effective controls.

By Roy C. Bartholomae

An accurate characterization of the vibration environment and a vibration qualification test derived from it will be a very useful tool for manufacturers of instrumentation for use on underground coal mining equipment. Recognizing this, the Bureau of Mines sponsored a study wherein vibration levels were measured on mining equipment to form a basis for developing the required vibration test. The data base was composed of 160 samples taken at different positions on a variety of underground machinery. The data were analyzed and presented in a format typical of military vibration qualification tests. The form was shown to be virtually identical to the swept sine test envelope specified in MIL-STD-810B for tracked vehicles.

Jan 1, 1982

By F. Awotwe-Appiah, P. Koshy, J. Dankwah, J. R. Dankwah

This research investigates the generation of an effective carbonaceous material from waste ‘pure water sachets’ and their subsequent utilisation as reductants for the reduction of the Opon Mansi iron ore. Composite pellets of Opon Mansi iron ore and pulverised carbonaceous material generated from waste pure water sachets were heated from room temperature to 1200 °C in a gas fired furnace for seventy minutes. The reduced pellet was analysed chemically for its oxygen and carbon content using a LECO Oxygen/Nitrogen and LECO Carbon/Sulphur analysers, respectively. It was observed that nuggets of metallic iron were readily produced with the carbonaceous materials acting as an effective reductant and source of chemical energy. XRD analysis of waste ‘pure water sachets’ revealed that the polymer was semi-crystalline with peaks that were identical to those of high density polyethylene (HDPE). Gas emission behaviour of the iron ore-PWS pellet was studied in a horizontal tube furnace at 1200 °C using an infrared gas analyser; the results revealed an exhaust gas rich in the reducing gases CO and CH4 along with CO2.

Jan 1, 2015

By E. E. Creitz

Application of the usual chemical methods to the determination of beryllium in the mineral-dressing products of a spodumene pegmatite was found to be unsatisfactory as to speed, accuracy, sensitivity, and range of analysis. A spectrographic method is described for the determination of beryllium. Samples are ground, mixed with borax, high-purity, flake graphite, and an internal standard; then they are fused, reground, pelletized, and excited with a high-voltage-spark discharge. Investigation of several spectrographic techniques to overcome matrix effects are described. The method developed gives results for beryllium in the concentration range from 0.002 to 5.0 percent; the average probable error of duplicate determinations was below 3.0 percent of the quantity present. INTRODUCTION The main source of beryllium in pegmatite is the mineral, beryl. Many of the conventional methods for the determination of beryllium in beryl are not suitable for control purposes because of lack of speed and accuracy, especially in the range below a few tenths percent. Beryl resists the usual chemical attack and can be lost in a hurried chemical analysis.

Jan 1, 1958

By A. U. Miller

Definite progress has been made in accident prevention in Illinois during the past few years; the State Department of Mines and Minerals is receiving excellent cooperation from coal companies and employees, the companies are making greater effort to maintain their mines in good condi- tion, and the employees are eliminating more unsafe practices. As a result, some coal companies have made commendable safety records that prove that coal can be mined with a comparatively low accident rate. However, there is need for further improvement, as the accident rate of the State as a whole is much higher than it should be. During the 55-year period 1882-1936, in- clusive, reports of the State Department of Mines and Minerals show a total of 7,005 (an average of 127.36 per year) men killed in and around the coal mines. Of this number, 6,425 (91.7 percent) were killed underground, 346 (4.9 percent) in the shaft, and 234 (3.3 percent) on the surface. Of the fatalities underground, 3,300 (51.3 percent) were killed by falls of roof, sides, or face coal, 1,167 (18.1 percent) by haulage, 639 (9.9 percent) by handling explosives, 579 (9 percent) by explosions, 151 (2.3 percent) by electricity, and 589 (9.1 percent) by other means. Of the fatalities in the shaft, 171 men (46.5 percent) were killed by falling down the shaft, 14 (41.6 percent) by the cage, and 31 (8.9 percent) otherwise. On the surface, 113 (48.2 percent) of the fatalities were due to railroad cars, 51 (21.7 percent) to machinery, and 70 (29.9 percent) to other causes. The fact that 7,005 lives (an average of 127.36 per year) were lost during 1882-1936 is sufficient evidence that in the past too little interest has been taken in safety by either the management or workers. A realization of this deplorable loss of life should act as an incentive to the industry to make greater effort to prevent accidents in the future. After an accident occurs, the facts pertaining to it become history, and anything that may be done afterward cannot change in any way the damage that has already been done, such as loss of life, personal injury, and destruction of property. The main benefit that can be derived from an acci- dent is that suitable procedure may be adopted and some lesson may be learned to aid in preventing a similar accident in the future. All accidents, par- ticularly serious ones, therefore should be investigated and an effort made

Apr 1, 1938

By Ryosuke O. Suzuki

A new cell concept for calciothermic reduction is proposed in which the titanium dioxide instead of TiCl4 is used as the raw material for reduction, Metallic calcium is needed as the reductant of a thermochemicaily stable oxide, such as TiO2. CaCl2, is selected as the solvent of Ca and simultaneously as the solvent of CaO. The reduction system consists of a single cell where both the reduction reaction and the electrolytic reaction for recovery of reducing agent coexist in the same molten CaCl2 bath. A few mol%Ca dissolves in the melt and gives the media a strong reducing power. Sufficiently deoxidized metallic titanium deposits and forms a slightly sintered granular sponge. Both mechanisms of the halide flux deoxidation and the electrochemical deoxidation work efficiently for these fine precipitates, The reducing agent is in situ recovered by electrolysis of CaO because the molten CaCl2 he a relatively large solubility for CaO Some cell designs and modifications are proposed for industrial applications.

Jan 1, 2003

By M. Ramprecht, M. Wu, A. Kharicha, A. Ludwig, H. Holzgruber

"The influence of the frequency of AC power supply on the magneto-hydrodynamic during the electroslag remelting process is studied. The focus is on the electrodynamic field and its resulting mechanical effects on the flow and liquid interfaces. The possible influence of the electrochemistry on the droplet formation is qualitatively discussed.IntroductionThe electroslag remelting (ESR) process is a secondary melting technique which can be used for a variety of metals and alloys, provided appropriate fluxes (slags) and melting parameters are employed. The ESR process is presently operating mostly with AC current of about 50 Hz. However for reasons primarily of inductive losses in the electric circuit, furnaces for ingots larger than 1 m, use or are projected to use current of very low frequency (< 5 Hz). Effects of lower frequencies (2.5-5Hz) on macrostructure and non-metallic inclusions were recently studied by Chang [1]. Most of investigations were performed either with DC power or with AC of 50-60 Hz [2-4]."

Jan 1, 2012

By Eiichiro Mizushima

Catalyst systems comprising (Ph3P)AuCH3 and acid co-catalysts were found to be highly efficient for hydration of alkynes to give ketones. Methanol was the best choice of solvents. Introduction Hydration of carbon-carbon unsaturated bonds is one of the environmentally benign routes to the carbon-oxygen bond formation. Hydration of alkynes forming carbonyl compounds, an important variation in this category, is a well known reaction which has been extensively studied. The reaction by acid-catalysis is the most conventional method, while it is applicable only to electron rich acetylenes to obtain satisfactory yields (1,2). The hydration of simple alkynes usually requires another catalyst (co-catalyst), typically a mercury(II) salt (3), which is inconsistent with the guiding principle of Green Chemistry (4).

Oct 1, 2003

By S. W. Poole, J. A. Rosa

THE object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-Committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition 0f the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. STEELMAKING DATA Melt.-The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping temperature, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.-Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.-Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 ½ in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. SECTIONING AND PREPARATION FOR SULPHUR PRINTING Because of previous favorable experience in sectioning ingots up to 21 ½ in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. z and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200°F.

Jan 1, 1944