Search Documents

By Theodore M. Olson

The Washington State Highway Department consists of seven geographic dis¬tricts. District offices are located in Seattle, Wenatchee, Olympia, Vancouver, Yakima, Spokane and Bellevue. District is covered from the Spokane office, and is responsible for the six counties in the northeast corner of the state (Fig.l). It is bordered on the north by the International Boundary, on the south by the Snake River, on the east by the Washington - Idaho border, and on the west by a north-south line thru Lake Roosevelt. The landslides to be discussed in this paper are at Colfax, Washington, which is located in the southeast corner of the district. The town of Colfax is situated in a narrow valley eroded into the Tertiary volcanic basalts by the Delouse River. The valley walls are steep and generally colluvium mantled. State Highway 1°c, from Spokane to Colfax, descends into the valley from just north of Colfax on a bench cut into the valley wall. The highway department designed a widening project to increase the misting two lane roadway to three lanes, thus providing a passing lane for uphill traffic. The third lane was constructed as a cut section for the entire length. Construction excavation was begun at the top of the hill in silts of eolian origin. Proceeding downhill, excavation encountered three individual basalt flows with two zones of palagonite tuff separating them. The upper palagonite zone was dry, and excavation proceeded across this zone with no mishaps. The lower palagonite zone carried considerable groundwater. As excavation crossed the lower zone landsliding became contemporaneous with excavation, due to removal of toe of slope and saturated conditions. Remedial measures for landsliding consisted of designing shot rock buttresses across the palagonite zone and also the installation of horizontal drains to reduce hydrostatic pressure.

Jan 1, 1971

By J. Pang

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and AC impedance spectroscopy techniques. Analysis of the impedance spectra using equivalent circuit models has made it possible to suggest layerwise growth of surface films. From the value of equivalent circuit parameters, properties of the surface layers are inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution and give rise to changes In contact angle and flotation response. In agreement with prior investigations, the present study shows that flotation recoveries alone cannot be used to determine the effect of collector on flotation of chalcopyrite. The rate of flotation is a more sensitive parameter to determine the role of collector on floatability of chalcopyrite.

Jan 1, 1989

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023

By Qiang Zhong, Bin Xu, Qian Li, Wei Gao, Yongbin Yang, Yaxuan Wang

Lump coal with high volatility is used for providing heat and reductive gas, and ensuring permeability in COREX. However, it is apt to be pulverized in transport and storage process. Therefore, comprehensive utilization of the pulverized coal to produce coal briquettes with appropriate binders is significant, among which the molasses binder cannot meet the technological requirements. In this paper, coal tar pitch binder and BJ additive were used in briquetting and carbonizing process of coal powder. The results showed that BJ effectively activated cold state cohesiveness of the pitch and make it bond the coke particles to a firm briquette at room temperature .Carbonizations of coal and coal tar pitch achieved obvious constriction and formed a carbonized skeleton. The drop resistance of wet briquettes reached over 50 times/1meter. When cured at 1000 °C for 1h under nitrogen atmosphere, the compressive strength of carbonized briquettes came to 6.43 Mpa.

Jan 1, 2016

By H. J. Cao

Valuable elements could be extracted by microorganism ferment fluid from bauxite, which mainly due to bacteria acid namely organic acid. And after leaching, reclaiming the remainder organic acid in leaching solution was an important procedure for bauxite leaching process. the re-searching status about organic acid reclaiming process from bauxite ore bioleaching solution was summarized. Common processes for recycling organic acid from bauxite bioleaching solution in this period and their advantages and disadvantages, research aspects which need being confirmed for the future were Indicated

Jan 1, 2014

Scenario reduction is designed for selecting a representative subset of geostatistical simulations out of a much larger set. Three steps are involved: measuring the dissimilarity between two simulations; finding a metric to measure the distance between any subset of k simulations and the full set of N simulations; and finding an efficient algorithm for selecting the subset that minimizes the metric. This paper focuses on the third question. We show that genetic algorithms are an efficient way of approaching the minimum when the population of subsets to be sampled is large. Two case studies based on the Walker Lake data-set are presented: firstly choosing k=4 simulations out of a total of 100, and secondly choosing 20 out of the same 100 simulations. In the first case it was possible to compute all possible combinations exhaustively and hence to demonstrate that the algorithm converges to the true minimum. This was not possible in the second case. Instead we demonstrate that it outperforms the random draw algorithm used in earlier work. A procedure for tracking individual selections during the iterative procedure was developed. This allows us to measure the evolution in the percentage of progeny resulting from crossing-over and from mutation that survived in the next generation. It gives valuable insight into how to choose the parameter values in the algorithm. Another key finding is that there is a trade-off between the number of individuals per generation and the number of generations required for the algorithm to converge.

Jan 1, 2014

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are some of the most widely used instruments in a variety of industrial applications. Their major functions are to sort, classify and separate solid particles and liquid droplets within a multiphase flow system. Research studies employing both experimental and numerical methods recognize that the performance of a cyclone is related to its geometric dimensions as well as the inner flow pattern. Although many successes have been achieved over the past years, the majority of investigations only focused on the simplified design of cyclone geometry and on single-phase flow. Therefore, this study set out to investigate the flow field in a new-design hydrocyclone and used particle image velocimetry (PIV) to explore the complex swirling flow behavior inside the cyclone within an air core. The flow field inside the cyclone was also studied by computational fluid dynamics (CFD) simulation using a commercial CFD package. Different turbulent models were tested in this study with a moderate-size mesh, and the interface of liquid phase and air phase was predicted by the volume of fluid (VOF) model.

By M. Bigdeli Karimi

In this study, the effect of strain level and holding time in semisolid temperature range via SIMA process on AS21 Mg alloy was investigated. Some cylindrical samples of this alloy with 1cm in height and 2.5cm in diameter (H/D=0.4) were compressed to 10%, 20%, 30% and 40% at 300-C. Then, the samples were reheated in semisolid temperature range at 614°C for various times. The results of optical microscopy and image analysis showed that with increasing of strain and holding time, dendritic structure changed to equi-axed structure, gradually. Also, the best conditions to obtain good globular structure were achieved. Furthermore, it was seen that after compression and reheating, Mg2Si intermetallics with Chinese script morphology converted to dispersed-fine particles which were distributed into the ci-Mg grains.

Jan 1, 2007

By J. W. Walkiewicz

Studies were conducted by the Bureau of Mines to develop a method for fabricating Sm-Co permanent magnets. This method consisted of arc-melting, crushing and grinding the alloy, alining and pressing the powder, and sintering the green compacts. Results indicated that the optimum composition was 36.7±0.3 weight-percent Sm and 63.3±0.3 weight-percent Co. This composition was obtained by blending together Sm2C07 and SmCo5. The maximum values exper¬imentally obtained were MHC = 27.4 kOe, BHc = 7,510 Oe, Br = 7,810 G, and (BH)max = 15.1 MGOe. The optimum sintering temperatures and grinding times for maximum MHc and (BH)max were determined. Lowering the grinding temperature from 0° C to -60° C resulted in a significant increase of magnetic properties.

Jan 1, 1973

By Michael J. Castner

"INTRODUCTIONMultiple-seam mining is an ever growing concern for engineers and mine management in every portion of the mining industry and is especially true for coal mining operations. The goal of this report is to identify the location and severity of multiple-seam interactions, provide AMSS calculations performed on the worst of these locations, and follow up with a visual examination of the underground physical effects on the roof and ribs in the locations identified for analysis. Multiple-seam mining is increasingly being studied because:1. Multiple-seam mining can create a multitude of problems such as roof falls, pillar crushing, pillar failing, rib spalling, floor heave, and inundation of water, gas, or oxygen-deficient air that can disrupt mining operations and threaten the safety of the miners.2. Multiple-seam mining is becoming more prevalent due to the depletion of virgin coal reserves.Currently, coal mining in the United States has progressed to the point that a growing number of mining companies are operating in coal seams located above, below, and/or adjacent to previously mined out coal seams. As a result, the state and federal governments are enacting higher safety standards on mining operations. For example, in years past, pillars may have been properly designed to handle single seam interactions for a particular mine or mines; however, today, where mining is now being considered above or below a previously mined area, these loading conditions may not be adequate to handle the removal of additional seams above or below the previously mined reserve. Studies from 1981 estimated that two-thirds of the mineable coal reserves in the United States would be impacted by multiple-seam implications. Today, over three decades later, it is obvious that most of the remaining mineable coal reserve will be influenced by previously extracted seams. Thus, thefocus on multiple-seam mining interactions on current and future mining operations. In 2012, underground mining in the United States produced 342,287 thousand short tons of coal. Northern Appalachia accounted for over 30% (103,301 thousand short tons) of this total (U.S. Energy Information Administration, 2013). Rosebud Mining Company and Western Allegheny Energy (RMC and WAE) have a combined total of 23 actively producing underground mining operations and at least four new mines under or ready for development. All of these mines are located in coal seams (Upper and Lower Freeport; Upper, Middle, and Lower Kittanning) of northern Appalachia (Pennsylvania and Ohio). Currently, more than half of the RMC and WAE mines are dealing with multiple-seam interactions. Seven mines are undermining previously mined out coal seams, and five mines are overmining previously mined out coal seams. Also, between these companies, five mines have inner-seam sloping possibilities (2 completed, 3 planned), most of which will result in mining over or under previously mined areas."

Jan 1, 2015

By DEVY DYSON, Brian Hart, JOHN LANGHANS, Stamen Dimov, STEVE YOPPS

A recent Nevada Gold Mines research program focused on pressure oxidation pre-treatment of a Carlin-type double refractory ore from the Turquoise Ridge Mine. The research team found that both arsenian pyrite and carbonaceous matter were highly oxidized within an hour at 300 °C using a bench-top autoclave reactor and that the gold recovery from the residues after cyanide/carbon-in-leach approached the technical limit set by the amount of gold encapsulated by silicate minerals. Although the 60-min pre-treatment at 300 °C yields robust performance when treating a whole ore, copper additives can catalyze the oxidation rate of carbonaceous matter and reduce the residence time needed at elevated temperature. Certain gangue minerals are susceptible to dissolution in acidic solutions at 300 °C, and this may cause poor gold recovery. This recovery challenge is mitigated by keeping free acid in the discharge solution below a key threshold.

Jun 21, 2022

By W. Blake McCullogh

It is often written that the purpose of any mining operation is to produce efficiently, safely, and profitably, and always to search for more efficient, safer, and more profitable methods. To provide for continual improvement, an attitude that is not only reasonable but also imperative, there is an obvious need for a high standard of competence among the ranks both of supervision and of those being supervised. It naturally follows that, to achieve this standard, planned training in every level of an organization is a definite necessity. There are many factors involved in the need for training, and the scope of a program is influenced by answers to such questions as: "What is the geographic location of the project?" "What are the duties of each job?" "What is the source of the working force and supervision?" "What are the hiring standards for various jobs?" "What is the availability of trained personnel?" "What is the availability of outside training facilities?" The approach in this chapter will be to consider a need for a maximum of training, and it may be applied by the reader to whatever extent is considered necessary in each individual situation. 14.2-1. Administration. It is a basic responsibility of every supervisor at all levels to train those who work for him. However in a very extensive training program, which involves supervisors and the working force, includes both compulsory and voluntary participation, uses outside and in-plant methods, and where the increasing complexity of jobs requires more specialization, the establishment of a training department is definitely war- ranted. This will consist mainly of instructors for related classroom training and preparation of manuals, etc., and the necessary clerical help. A training staff does not relieve the various departments of their responsibility to train, but it does have facilities, experience, and contacts that are inval-

Jan 1, 1968

By Jürgen F. Brune, SAMUEL A. LOLON, ADITYA JUGANDA, Gregory E. Bogin Jr

Historically, there have been many occurrences ofmine fires and explosions recorded in the United States and other countries that have demonstrated the existence of explosivemethane–airmixtures, herein referred to as explosive gas zones (EGZs). The risk of mine explosions can increase if the EGZs migrate out from the gob into the surrounding mine entries. Fluctuating barometric pressure is the common cause for EGZs outflowing or outgassing from the gob. Numerical analysis using a 3D computational fluid dynamics method was developed to fully understand the outgassing phenomenon. A number of simulations using various magnitudes and periods of barometric pressure changes indicated that the EGZ outgassing potentially occurs due to lags in pressure, which are strongly influenced by mine conditions and ventilation systems. An early warning system with a real-time pressure monitoring and the application of gob ventilation boreholes are recommended to detect and mitigate explosion hazards from gob outgassing.

Aug 24, 2020

By Stefan Mutl

By the term sorting one understands the separation of a material mixture into two or several products according to different material characteristics in the preparation technology. The oldest sorting procedure, the handpicking, is less and less used to separate different material mixtures because of the considerable personnel expenditure and the strict hygienic regulations at the workplaces in Europe. In general, the manual assortment is able to solve separation tasks, which could not be solved by machines so far. The picking is one of the most selective processing methods. However, the progress in the computer and sensor engineering today makes the creation of automatic picking devices possible, whose efficiency goes far beyond the possibilities of handpicking. Therefore in the future automatic picking will not only be applied to already common applications like the waste glass assortment by colour, but also to the assortment of complex composed material mixtures e.g. old shreddered cars. Thus, the automatic picking, supported by high performance computer systems and new sensor technology, gains more and more significance within many applications of waste processing. However, in order to apply automatic sorting procedures for different material streams within recycling processes, a substantial research and development need still is existing. The desire of the users is to sort more extensively in order to achieve products with bigger material varieties, In addition, the requirement of the accuracy of recognizing and sorting out of single grains rises, This lecture illustrates the procedure of the hand picking before it was employed in waste processing. Thus, a renaissance of a long forgotten method is happening in terms of today's state of the art procedure "automatic picking". Possible technologies, fields of application and future potentials of this technology are pointed out.

Jan 1, 2003

By Connor Langford, Murray Gant, Ken Massé

For public organizations, preparing accurate project cost estimates is a critical component in capital project planning. Project delivery methods provide a structured approach to moving projects through the design and construction lifecycle, and typically use cost estimates as key inputs at each stage to determine if the project will advance. As design stages can occur years or even decades before construction contracts are awarded, estimates need to make reasonable assumptions about how the work may be executed (means and methods) as well as potential future market trends so that appropriate values for material pricing, labour costs, escalation, and owner’s costs can be included. This process is challenging enough during stable markets, as historic trends can often be misleading and require a suitable understanding of economic factors to use appropriately. When you mix in the market volatility that has been observed since 2020, developing accurate project cost estimates becomes even more challenging. In cases such as this, having a structured approach to cost estimating that includes an adequate risk-based reserves cannot be overstated as it provides the basis for ongoing project decisions. This paper explores some of the historic and more recent market trends that have impacted key aspects of project cost estimates for capital project planning. It also provides recommendations on how to develop cost estimates for infrastructure projects, with examples from Metro Vancouver, which plans for and delivers regional-scale services to 2.6 million residents. A brief commentary on the use of escalation clauses in contracts is also presented.

Jun 13, 2023

By Ali Jaberi Zamharir, Abolfazl Shoghian‐Alanaghi, Hossein Aghajani, Arvin Taghizadeh Tabrizi

In this study, the leaching rate of molybdenite concentrate was evaluated in sulfuric medium, and the influence of the diverse oxidants including hydrogen peroxide, manganese oxide, copper sulfate on the leaching rate was studied. Also, the effect of the addition of the ethylene glycol to the hydrogen peroxide was studied and results showed that with the addition of ethylene glycol, the leaching rate is increased 55% from 41% up to 80.3%. The optimum condition is achieved as 0.7 M of H2SO4, 4.4 M of H2O2, and 3.5 M of EG at 30 °C within 4 h of leaching time and 500 rpm. Also, inserting the oxygen with the pressure of 6 bar to the leaching autoclave, the leaching rate is increased more up to 86.4%. Finally, the leaching process was studied kinetically and the determined mode of controlling factor was specified based on the activation energy which equals 46.252 kJ/mole indicating the chemical reaction mode.

Jun 5, 2022

By E. Asselin

Electrochemical polarization experiments were conducted on alloy 625 in ammonia solution between 25 and 225°C and the results were compared with those of an oxygen solubility model. Results confirm that corrosion is under oxygen control, Normalized corrosion rates are determined based on the rate of oxygen diffusion to the corroding surface, and the corrosion rate at 200°C (-9.7 µA.cm-2) is roughly 24 times higher than the corrosion rate at 25°C (0.4 nA,cm-2), An oxygen-solubility model for Supercritical Water Oxidation (SCWO) conditions was generated using the Redlich¬Kwong-Soave (RKS) equation of state, Results of the model confirm many of the experimental observations from SCWO reactors which suggest that corrosion is at a maximum at temperatures just short of the critical point, The RKS/oxygen diffusion model predicts that the corrosion rate at 365° C is ?85 times higher than the corrosion rate at 25' C. Given that a normalized corrosion rate is obtained, this type of model could be useful for selection of SCWO reactor materials.

Jan 1, 2005

By W. G. Diamond

Lightweight aggregates have become increasingly important to the construction industry. From 1953 to 1960, the quantity of the aggregates used in concrete block, precast and prestressed concrete, and monolithic structures increased about 92 percent. The present study was conducted in Bureau of Mines Area IV which encompasses the South-Central States of Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas. This is an administrative area and does not delimit a market area or imply an economic unit. Because of the increasing importance of metropolitan areas in evaluating economic growth, significant data showing relationships between growth of the metropolitan areas and the lightweight aggregate industry are included.

Jan 1, 1964

By Christopher R. Winter

Mining companies have sharpened their refocus on their tailings management strategies in recent years. Mining companies with tailings storage facilities that use the upstream construction method have been challenged to track the evolution of industry standards, assess risks, revise design, and communicate design revisions with regulators. While many aspects of best practices and industry standards have evolved in recent years as an attribute of continual improvement, the controlling standard in the design of many upstream dams is understanding the foundational strengths of hydraulically deposited tailings. Following best practices and industry standards, Hibbing Taconite Company managed by Cleveland-Cliffs, began the re-evaluation of foundation strengths underlying a system of upstream dams at the company’s iron ore mine tailings storage facility in northern Minnesota. Initial steps in the re-evaluation require reanalysis of design parameters and recommendations by the Engineer of Record to the Owner, which was followed by a series of meetings with the Technical Review Board to determine an initial path forward. Once a path forward and preliminary design parameters were determined, the Owner engaged with the State Dam Safety Engineer to discuss and seek approval of the plan. With continuous regulatory engagement throughout the process, further refinement of the design parameters for the hydraulically-placed tailings foundations underlying upstream dams began with field and lab geotechnical investigations. Following a review of risk assessments and trigger actions response plans, Hibbing Taconite revised its tailings storage facility operating plans and budget for the coming years. Based on the findings of the re-evaluation, reanalysis, and refinement of parameters, a paradigm shift was realized with the hydraulically placed tailings foundation strengths underlying the upstream system of dams. This paper explores the path that the Hibbing Taconite Company followed to understand the paradigm shift and construct downstream improvements. The plan involved tailings re-characterization, dam design revisions, operating plan reconciliation, budget revisions, wetland permitting, dam safety permit amendments, storm water prevention plans, borrow materials studies, new concrete decant structures and the pursuit to recognize and be consistent with industry standards.

Feb 1, 2024

By J. U. MacEwan

Introduction The equilibrium between copper, zinc, and chlorine may be considered as the simultaneous equilibrium of the two separate chemical reactions of formation of the stable chlorides of copper and zinc at the temperature of the reaction i.e., l440°K. (1,167°C., 2,133°?F.)§ [Zn(g) +Ciz(g) ZnCl2z(g). ... (1) ] [2Cu(l)+Cbi'g) Cu2Cl2(l 1 ....... (21 ] Subtracting, [Zn(g) +Cu2(Clz(l i ZnClz(g) +2Cu!l) ... . (3) ] If this reaction is carried out with a copper-zinc alloy at some constant temperature above the melting point of brass, and at a total pressure of one atmosphere, the equilibrium concentrations obtained will depend on the free energy decrease .of the reaction as written in (3) and on the activities of the various components in. the reaction mixture. If the equilibrium is examined from the point of view of the phase rule, it is a three-component system, and if it exists in two phases (liquid and gas) it will have three degrees of freedom. If the restrictions of constant temperature and pressure are imposed, the degrees of freedom are reduced to one. This means that, in a two-phase system under these conditions, each different alloy phase will be associated with a gas phase of constant composition.

Jan 1, 1951