Search Documents

By M. J. Pazuchanics

This U.S. Bureau of Mines report presents results from an ongoing investigation of the use of adaptive signal discriminating methods to distinguish between cutting coal and cutting mine rock. Bit-cutting forces and tool vibration were measured in the laboratory as a linear-cutting apparatus (LCA) made constant-depth cuts in coal, sandstone, and shale test specimens. A portion of the collected data has been analyzed and some preliminary results are given here. The influence of data bandwidth, data window size, number of signal features, and voting among classifiers on classification performance are noted. Results to date, based on ideal-cutting conditions and simple geologic materials, indicate that of the four classifiers tested there appears to be no single best classifier. Usually, classification accuracy showed slight improvement as the number of features considered for classification increased. The highest classification accuracies were achieved when voting was conducted among classifiers followed by voting among force components.

Jan 1, 1991

By E. O. Wagner, A. W. Koth, V. F. Parry, J. B. Goodman, D. C. Gernies

"INTRODUCTION A commercial-scale pilot plant for gasification of lignite was completed by the Bureau of Mines at Grand Forks, N. Dak., early in 1945 as an extension of work on, gasification of low-rank coals initiated in a smaller pilot plant at Golden, Colo., during 1943. The development work on this plant was part of a program to make reducing gases from lignite for beneficiation of low-grade iron ores. The background of this project has been described in a previous report. 6/ The present report describes the major features of the large pilot plant, a record of experimental operating data during five runs totaling about 1,800 hours, .and results of experimental work on the small pilot plant at Golden during 1945.This project has created considerable interest because heretofore there has been little success in several attempts to gasify American lignites.Furthermore, the methed employed is a departure from conventional processes. Natural lignite is fed continuously into an externally heated annular retort and is converted into water gas by heat conducted through alloy metal walls. Because of the high thermal conductivity of metal, the rate of gasification is several times greater than can be obtained when employing refractory walls. The process has been developed to a part that leaves one major question unanswered. - ""How long will the alloy last under practical operating conditions?"" - and this question has aroussed the interest of the Coal Division of the Bureau of Mines in this new development.Owing to the high reactivity of the lower-rank fuels, the water-gas reactions proceed rapidly at medium temperatures of 1,650°F. to 1,800°F. These temperatures can be attained in a reaction zone heated by external means when the temperature of the retort does not exceed 1,900°F. while transferring from 6,000 to 7,000 B.t.u. per hour per square foot. Such rates are several times greater than can be attained through refractory walls as employed in the Didier-Bubaig 7/ and the Ahrens processes. 7/ Therefore, the investment cost of the gas generator per unit of capacity will be considerably lower for the higher-capacity process. However, the maintenance cost of metal vessels will be higher than that of refractory retorts, and this emphasizes the importance of large-scale operation to determine the life of an alloy retort under practical operating. conditions."

Sep 1, 1947

By D. A. Karvonen

In 1970, the Government of Saskatchewan instituted a program aimed at resolving the dilemma of excess productive capacity over the market demand which existed for potash produced in Saskatchewan. The two primary elements of the program were prorationing of potash production to market demand and a minimum selling price. The paper reviews the factors, both local and international in nature that led to the introduction of the program. The licensing mechanics and the operation of the program, along with the changes that have been introduced in two and one-half years of operation, are discussed. Attention is given to the results of the controls as they affect the industry and the province. Also discussed is the outlook for Saskatchewan potash in world markets.

Jan 1, 1973

By D. Caruso

The health and financial costs of cumulative injuries are plaguing the mining industry. Industry leaders are concentrating on reducing the risk of injury to their workers through design and redesign of work environments. While ergonomics is not a currently regulated field, many mines are realizing that the only way to tackle their most costly injuries, cumulative injuries, is to make the proactive choice to understand those injuries, their root causes and to make workplace changes to prevent them from occurring. Reduction of these injuries not only improves the health and morale of the workers but increases productivity and profit for the companies. Knowledge and reporting of ergonomic risk factors by employees and ergonomics committees is key to these changes and to the reduction of cumulative injuries. NIOSH is developing strong relationships with industry associations and equipment manufacturers to leverage their communication abilities to transfer knowledge to their customers and make a difference in the health and safety of U.S. miners. The benefits of a formalized approach to reducing these injuries along with examples will be presented.

By M. R. Campbell

"IntroductionON THE LAST DAY of December, 1951, a half-century of steel production was completed in the open hearth department of Dominion Iron & Steel, Limited, in Sydney, Nova Scotia.During that period, almost every known variation of basic steel making practice was used in working out a steel making process which would overcome the difficult metallurgical problems imposed by the use of Cape Breton coal and Wabana ore.This paper is presented as a brief review of these steel making practices, setting forth the fundamental metallurgical factors involved in their success or failure.Establishing the IndustryThe story of steel production at Sydney is closely interwoven with that of coal. The steel industry owes its inception to a desire on the part of the Dominion Coal Company, which was incorporated in 1893, to improve its marketing position by increasing sales of slack coal and providing a year-round demand for its product. Accordingly, the Dominion Iron and Steel Company, Limited, was incorporated on March 30th, 1899, with Mr. H. M. Whitney -who was President of the Dominion Coal Company -as its first President. The new Company was given powers to manufacture and process iron and steel, and to mine all minerals, including coal.A strong inducement to the industry was the bounty offered by the Dominion Government for the production of both iron and steel."

Jan 1, 1952

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By Alvaro Veizaga, Samuel Cuellar

In recent years, Industry 4.0 has generated a change in the way companies in various industrial sectors design, produce and deliver products and services, and is focused on the interconnection of systems, the advanced access and management of large amounts of data in real time, and the implementation of emerging technologies such as the Internet of Things (IoT). Artificial intelligence (AI), machine learning (ML), digital twins (DT), robotics, virtual and augmented reality (VR/AR), among others [1]. DTs are accurate and dynamic virtual models that replicate physical systems, where it is possible to simulate and optimize operations before implementing real-world changes [3]. These features make it possible to reduce investment costs, minimize risks and improve strategic decision-making. These benefits are of utmost importance for tailings storage facilities (TSF), since they are facilities aimed at the safe storage of tailings and with the constant need for growth [4]. This paper evaluates the applicability of a DT in a TSF from a conceptual perspective, providing the advantages of its implementation, but also the barriers identified in the industry based on the authors’ experience.

Feb 1, 2025

By W R. Honeywell

Two series of laboratory flotation tests were carried out to study the treatment of Faraday ore by two-stage flotation. First the acid-consumers and then the uranium minerals were floated. On ore ground in the Faraday mill grinding circuit, and using Faraday mill water in the flotation step, a recovery in the flotation concentrate of from 91 to 93 percent of the uranium was obtained in 45 to 50 per cent of the weight at a grade of 0.24 per cent U30s. The saving of acid in leaching the uranium-bearing flotation concentrate, as compared to leaching the whole ore, ranged from 30 to 46 per cent. The average over-all extraction resulting from flotation and leaching of the flotation concentrate was 88.1 per cent. The best collector for the acid-consumers was sodium oleate. Acintol F A-1 emulsion was the best collector for the uranium minerals, and, in the uranium flotation step, an acid pH in the slurry was found to be necessary. The reagent costs were estimated to be 22 to 26 cents per ton of ore.

Jan 1, 1963

By Masoud Askari, Ahmad Rafizadeh, Shahamat Rostami, Mohammad Qaredaqi

Gole - Gohar Iron ore mines located in Sirjan, Southeast of Iran, have more than 1 billion Iron ore deposit and this area comprises 45 % of Iran Iron reservoirs. The aim of Wet tailing processing line is recovering Hematite ore from wet tailing of Gole - Gohar iron ore processing plant. The Investigations of Hematite recovery plant showed that the recovery of Iron ore to concentrate in Wet Tailing Processing (WTP) line is very lower than that has been predicted, sampling, and designing of the process parameters are not accurate and designed magnetic field intensity is not reasonable for the recovery of Iron in form of Hematite in this line feed. Applying of MIMS in WTP separator and changes in circuit caused in overwhelming increase of Fe recovery, from 11 to 40%. Although recovery of WTP line was improved, but low recovery of this processing line and high content of Hematite ore in WTP tailing, made applying Wet High Intensity Magnetic separators unavoidable. Two kinds of WHIMS have tested for processing of WTP line tailing. Results showed that traditional Jones separator with grooved plate matrix, is more suitable to achieve a better quality of concentrate compared to Slon® separator.

Jan 1, 2014

By Andrew Budek

"Analytical and experimental work has shown that achieving the full inelastic lateral capacity of a pile may require the formation of a plastic hinge below ground level, in the pile shaft. The confining action of soil about the pile shaft was further been shown to greatly enhance the ductility capacity of the pile. An experimental program was therefore undertaken to build in the effect of external confinement through the addition of a GFRP jacket to the subgrade plastic hinge region. Two piles were thus modified, and compared to an unjacketed pile in a test rig which simulated a subgrade moment pattern and soil confinement. The ductility achieved by the jacketed piles was found to be substantially lower than an unjacketed control specimen. Failure mode of the jacketed specimens was also undesirable, involving complete tendon rupture and sudden loss in capacity IntroductionSeismic loading of concrete pile shafts can result in a demand for inelastic response. In the case of a superstructure supported by a single pile (i.e., a pile-column forming a single-column bridge pier, in which there is no rotational restraint at the top of the pile}, a plastic hinge will form below grade, at a depth which varies with soil properties and above-grade height of the center of seismic mass.In the case of a superstructure supported by multiple piles, there is rotational restraint, and the connection will experience inelastic action first. However, development of the full lateral inelastic capacity of the pile may call for the formation of a second, subgrade plastic hinge (fig. 1 )."

Jan 1, 2005

By Karoly (Charles) Kocsis, Kyle A. Scalise

Understanding the climatic conditions in underground mines is necessary for efficient ventilation design, cost savings, and to ensure the health and safety of mine workers. Large volumes of ventilation and climatic data including air volume, barometric pressure, dry bulb temperature, and relative humidity were collected at active underground precious metal mines in Nevada, which allows for the determination of wet bulb temperature and other key parameters. Through the utilization of neural networks, the wet bulb temperature at the bottom of the intake shafts is predicted, while taking into account the “thermal flywheel effect” (TFE). Wet bulb temperature is one of the most important climatic parameters to model and understand because it significantly affects the work conditions and the cooling capacity of the ventilating air. The accurate prediction of the dry bulb and the wet bulb temperatures at the bottom of intake shafts is critical when assessing the climatic conditions in future underground mines and deciding onwhether a cooling system is needed to assure adequate working conditions throughout themine. By utilizing accurate predictions of wet bulb temperatures and other climatic parameters, mine personnel will be safer as reported by Bluhm et al. (2003), and a more accurate ventilation design can be achieved resulting in major cost savings for underground mines.

Mar 3, 2021

By D. T. Pritchard

"Introduction""No accounting system is very good, and all of them are infinitely variable*.”The purpose of this chapter is to discuss those facets of a typical accounting system which are most commonly encountered by operating managers in mineral processing plants. However, before concentrating in any detail on these it is important to understand the broad purposes and basic techniques of any accounting system in any major business.The three broad purposes of an Accounting System are:- Administering, controlling, and recording the flow of cash in and out of the business. Cash is, of course, converted into other assets (or stores of value) such as inventory, plant and equipment, etc. These assets also have to be administered, controlled and recorded.- Internal reporting to Management for information, for control, and for use in making business plans and decisions. - External reporting to stockholders, government, lenders and other outside parties.In this chapter we shall organize our discussion of accounting practice in mineral processing plants around these three purposes of accounting and focus in some detail on specific practices and techniques with which operating personnel will be routinely involved. This chapter is divided into the following: Accounting Basics; Administration, Control and Recording of Cash Flows; Internal Reporting; Planning and Budgeting; Cost Control; and External Reporting."

Jan 1, 1989

By E. Marcotte

"Technology developments and improvements are imperative to maintain a viable mineral processing industry. In order to achieve optimum implementation of technology in processing plants, safety conscious and efficient work forces are required. Effective management methods are required to prevent employee injuries, equipment or environmental damage and process losses. Good leadership also provides for employees to perform their work in the safest and most efficient manners to attain optimum recoveries of the valuable minerals and produce high quality mill products. Equipment and processes must be designed, operated and maintained as required to assure safe and efficient mineral processing.INTRODUCTIONThe Canadian mining industry must contend with many challenges to attain and maintain a competitive position in today's global market. Canadian Mineral Processors play a vital role in meeting the challenges and achieving optimum mineral productivity.Ongoing technology developments and improvements continue to be imperative to maintain a viable mineral processing industry. The efficient implementation of technology developments requires a safety conscious, skillful and productive work force.In addition to technical and human resources, challenges may also include governments, labour unions or environmental advocates who at times may appear to be misguided or unrealistic. Canadian Mineral Processors must not allow themselves to be overwhelmed by these apparent obstacles but must use their demonstrated ingenuity to achieve successful solutions.It should be recognized that the majority of the Canadian work force are, in fact, a potentially talented and skillful people with ambitions to excel. As leaders of people, we must provide the methodology, incentive and direction that will allow our work forces to realize their ambitions. If the potentials of our work forces are not recognized and leadership is not properly exercised much loss will occur. That is, safe effective and efficient work will not be achieved."

Jan 1, 1993

By Vladimir G. Kochnev

"Autogenous and semi-autogenous grinding (AG and SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills. However, existing AG and SAG technologies still can be improved and have an immense potential from the viewpoint of economic benefits.Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that comminution in AG and SAG mills can be performed in a more effective way. The company’s approach comprises the following elements:- Novel mill design- New liners and lifters- Novel discharge grid design- Technique of treating material of critical particle sizeA novel mill of the cantilever type capable to operate in the AG and SAG mode has been developed. The cantilevertype mill has a high diameter to length ratio, which dramatically increases the throughput rate, and is characterised by high reliability, fast installation and low capital and operating costs.Tests of the new heel-shaped liners, originally aimed at improving the intact condition of diamond, indicated that they play an important role in the grinding process. Tests performed by TTD jointly with ALROSA, MINTEK and Anglo-American Corporation, demonstrated that the heelshaped liners provided the increase in the throughput rate varying from 30 to 80 % and the decrease in power consumption in the range 30-55 % for grinding of kimberlite and platinum-containing ores.Investigation of the influence of the main grid parameters on the efficiency of grinding led TTD to a special design of a mill discharge grid, with a radial location of openings, the slot width varying from the periphery to the centre and the grid surface provided with “heels”. The design allows one to control the particle size distribution of the ground product without affecting the grid throughput rate."

Jan 1, 2003

By M. A. Golozar

Partially stabilized zirconia (PSZ) has been proven to be an excellent candidate as a thermal barrier coating (TBC) for hot sections in, for instance, heat or internal engines and gas turbine parts. The main functions of these coatings are reduction of heat losses, reduction of fuel consumption, increasing efficiency, and extending durability and life. One of the main problems involved is wear behavior in the development of such coatings for these applications. Using air plasma spraying (APS) technique, conventional and nanostructured 8 wt % yttria partially stabilized zirconia (Y-PSZ) coatings were deposited on austenitic stainless steel (AISI 304) disc-shaped substrates. The coated substrates were subjected to pin-on-disc wear tests, using 10 mm silicon nitride and zirconia balls as the pin. The coefficient of friction was recorded in real time. The weight loss of coated substrates was measured. Coatings were characterized before and after being subjected to wear testing by various techniques including optical microscopy, scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDX) and X-ray diffraction (XRD). Effects of various experimental parameters such as wear distance, test temperature, and counterface material were also investigated. Results obtained revealed that, regardless of experimental conditions applied, the nanostructured zirconia coating shows better wear and tribological properties than those of the conventional one.

Jan 1, 2005

The Closure Risk model was developed as a new tool to aid decision makers in the complex area of mine closure. It uses a simple analytical technique that allows the decision maker to simplify what is often a complex mine closure process into more easily managed sub components. This systematic approach ensures that critical factors in the closure process are not overlooked. It also allows the most important issues to be highlighted. The model can also be used to produce quantitative estimates of risk by weighting and prioritising the issues to produce the Closure Risk Factor (CRF). Field trials at several mine sites in the Northern Territory of Australia in 2001 tested the model. The trials confirmed that the model has significant potential as a tool for decision-makers to assess in a structured, systematic manner, the major closure risks at individual mine sites. The risks include not only environmental impacts but safety and health, community, legal, financial, technical and other issues. The trials confirmed the value of a team-based approach and the inputs of key staff including environmental, production, mine planning, and community liaison personnel as well as mine management. Although the usefulness of the qualitative component of the model was established, it was found that, due to the influence of subjectivity, the utility of the prototype model to determine quantitative risk was of limited value. Using a continuous improvement approach, improvements to the model were sought. A refined model, incorporating the Australian Standard 4360 definition of risk and facilitated in-house risk assessment sessions was developed and tested against the data obtained in the field trial. This model, while maintaining the qualitative strengths of the original, allows more accurate absolute and relative quantitative scores to be calculated. This in turn facilitates comparisons between the issues at a single site as well as between different mines.

Jan 1, 2003

By Julian Dimitrov, Kremena Dedelyanova

"The paper presents research on hydrodynamic processes occurring at the elementary act of flotation. Discussed existing models to determine the effectiveness of conflict of bubbles with particles in vibration column flotation machine. The paper presents a disperser for a column flotation machine, in which the dispersion of the gas phase is carried out using vertical vibration with defined frequency and amplitude. The paper presents research of mechanism for the creation of air bubbles in vibratory column flotation machine. The factors influencing the increase in the duration of the bubble in the area of contact with the mineral particles are discussed. Research was carried out on the effect of frequency and amplitude of vibrations on speed of precipitation of mineral grains of different density. Formulas are derived for the parameter effect of vibrations, applicable to the design of flotation machine. The collision efficiency of the bubbles in vibratory column flotation machine is determined. The vibrations of the hydrated layer allow for cost-effective implementation of the elementary act of flotation by providing larger relative velocities at the contact point between the bubble and the solid phase. It is proposed to complement the model more accurate representation the mechanism of attachment of the particles to the bubble."

Jan 1, 2014

By Tracy T. Morris, Luis G. Navaro

"Anodic copper slimes produced during the electrolytic refining of copper are routinely batch leached to remove copper. At the Amarillo Copper Refinery, an atmospheric leaching process was converted to an autoclave pressure leaching system to improve the removal of copper, reduce the consumption of oxygen, improve leaching times and enhance tellurium recovery. The benefits of pressurized versus atmospheric leaching of slimes were soon realized by obtaining the desired level of decopperization in a shorter time and with lesser quantities of reagents. The autoclave was designed and constructed with a unique oxygen injection system that enables good control of the leaching process and with no plug-ups. Other features include a mass measuring system that balances the quantity of slimes to be leached to the desired final solution concentration based on initial feed concentrations. The end result was a more efficient and controllable leaching process for removing copper from anode slimes.IntroductionThe electrolytic refining of copper consists of an electrolytic cell filled with a sulfiiric acid based electrolyte and pairs of copper anodes and cathodes. When a current is applied, copper in the anode dissolves and is plated onto the cathode. Impurities within the anode that are more noble than copper do not dissolve and end up at the bottom of the cell and are referred to as slimes. Gold and silver are the main slimes constituents of interest because of their monetary value, but there typically are significant quantities of selenium, tellurium, lead, antimony, arsenic, bismuth, nickel, silica and tin. Copper is also present, usually as a metallic or as a reactant with tellurium, selenium, oxygen or sulfur and can range from 10 to 30% of the slimes fall."

Jan 1, 2012

By P Townsend, F Russell

Palabora Mining Company operates an integrated open pit mine, concentrator, smelter and refinery complex located in the Northern Province of South Africa. The Palabora open pit went into production in 1966, mining 30 000 t/d to produce some 62 000 tpa of copper. With continuous modification and improvement, a mining rate of 82 000 t/d, producing up to 135 000 tpa of refined copper, has been achieved. While these improvements have also enabled the mine life to be nearly doubled, the open pit will reach the end of its economic life by 2003. The Palabora orebody is vertical and the reserve extends to a depth of 1800 m over an area of 700 m by 200 m. Studies to assess the economics of mining the orebody by underground means began in the mid-1980s. These studies indicated that block caving is the lowest cost underground mining method that would generate a suitable return. In March 1996, a decision was made to develop a 30 000 t/d block cave mine that will extend the life of the Palabora Mining Company by a further 20 years. In terms of the relatively high rock strength and the resultant coarse fragmentation that is expected at the drawpoint, the Palabora cave can be considered rather unique when compared to other block cave operations. This paper describes the project in broad terms and details the mining method, particularly with respect to the cavability of the orebody and the design features to deal with the coarse fragmentation. The project commenced in July 1996 and final development of the undercut and drawbells is scheduled for completion in November 2003. This paper describes the status of the project and planning as of April 2000.

Jan 1, 2000

By D. Maxton

INTRODUCTION This paper traces the application of High Pressure Grinding Rolls (HPGR) at industrial and pilot scale in Australia. The Argyle Diamond Mine installed the first of two smooth segmented HPGRs during 1990 in an open-circuit secondary-tertiary crushing application to increase throughput. In 2002 a third HPGR was added to improve liberation and so increase the recovery of smaller diamonds. The latest improvements in wear technology (tyre with tungsten carbide studs) were incorporated in the design of this machine. Extensive HPGR pilot-plant trials were undertaken during the 1990s at both the Kalgoorlie Consolidate Gold Mine and the Boddington Gold Mine. The purpose of these trials was to evaluate HPGR as a method to increase throughput, as an alternative to SAG milling, and also to ascertain if downstream benefits existed. One of the challenges for HPGR circuit designers is to translate what occurs at small laboratory and pilot scale into what is likely to happen in a full-scale circuit. Scale-up from pilot machine results is normally recommended by manufacturers. However, such tests need relatively large quantities of material, particularly if meaningful data on wear are to be obtained. Laboratory tests are preferable, as they need relatively small quantities of ore, but may be questioned in terms of how they relate to full-scale operation. Modelling and simulation have played a particularly important role in this respect in Australia. Models are available which have proven to be very accurate at being able to scale throughput and specific energy response from laboratory to industrial machines. More recently, work in Australia has also been done in developing a model which has the potential to scale laboratory wear data as well.

Jan 1, 2004