Search Documents

By Eric Lindquist, John Compagnone, Gabriel Carvajal

"Condon-Johnson & Associates, Inc. (CJA) with the assistance of design consultant, Brierley Associates, designed and installed a water tight shoring system utilizing several ground improvement techniques jointly. Prior to the installation of the shoring system, a test program consisting of the installation and testing of 7 jet grout columns; 1 soil mix panel; 7 soil anchors and 3 tie downs was performed to verify design assumptions. State-of-the-art quality control measures were employed throughout the project.The shoring system consisted of:•,Deep Soil Mixing (DSM) wall utilizing triple axis tooling to install overlapping columns along the perimeter of the proposed excavation to a treatment depth of 54 feet.•,Installation of steel piles in DSM to provide rigidity to the wall.•,Installation of a jet grout bottom seal, installed from surface to a depth of 58 feet below existing grade.•,Installation of 153 soil anchors, 1-1/4” diameter and 47’-6” length, to tie the jet grout bottom seal to the native soil below to resist hydrostatic uplift, installed from existing grade to a depth of 91 feet.•,Installation of walers and pipe struts for internal bracing•,Installation and stressing of 117 tie downs, 1” diameter and 16 ft length, to tie the pump station mat slab to the jet grout bottom seal, installed from inside the excavated pit.Subsurface conditions at the site consist of uncontrolled fill materials to a depth of 20 feet comprised of sandy silt and clayey sand. The native soils underlying the fill generally consist of soft and compressible lean clay and silt with varying amounts of sands to a depth ranging from approximately 44 to 54 feet below ground surface, which in turn are underlain by dense to very dense silty sand. The groundwater elevation at the site is approximately 8 feet below ground surface.This paper covers the design aspects, construction, and quality control measures undertaken by the geotechnical contractor, with supporting figures.INTRODUCTIONThe owner, County Sanitation District No. 2 of Los Angeles County, designed upgrades to their existing Long Beach Main Pumping Plant Facility. The upgrades consist of a new pump station that includes a reinforced concrete below-grade wet well and dry well, a two-story operations building, two 78-inch diameter pipe inlets, two 42-inch diameter discharge pipelines connecting the existing manifold, two pipe junction structures, two insert-type junction structures, and electrical transformers. This paper focuses on the excavation shoring for the new pump station. The original shoring design concept for the pump station excavation illustrated on the contract plans consisted of pressed in sheet piles, a jet grouted bottom seal with soil anchors, 2 levels of internal bracing, and tie-down anchors to resist hydraulic uplift forces on the buried pump station."

Jan 1, 2017

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By Ricardo Dobry, Alain Pecker, George E. Leventis, Ralph B. Peck

"This year’s DFI Outstanding Project Award is for the design and construction of the foundation scheme for the largest cable-stayed bridge in the world. In 1993, Gefyra, SA (a French/Greek consortium led by VINCI of Paris, France) was awarded a €750 million ($1billion+ USD) Concession Contract to design, build, fi nance, operate and maintain a three-span cable-stayed suspension bridge connecting the Peloponnese, Greece’s southernmost peninsula, with the mainland across the Gulf of Corinth. The contract extends over a 42-year period, 7 years for design and construction and 35 years for operation. The project was fi nanced through a combination of public funds, private equity and bank loans. Alternative foundation concepts that were considered included traditional driven piles, deeply embedded caissons and soil improvement. PROJECT CHALLENGESThe extreme technical challenges faced included:??Weak foundation soils composed of soft alluvial deposits consisting of interbedded layers of granular and cohesive materials with thin layers and lenses of gravel and liquefi able sand pockets; rock is believed to be at a depth of 1,000 m (3,500 ft) or more.??A very deep seabed exceeding 60 m (200 ft).??The requirement to withstand the collision of 180,000-ton tankers traveling at 16 knots.??Maximum wind forces of 250 km/hour (155 mi/hour).??Design seismic forces corresponding to Richter magnitudes of 7.0+ with peak ground accelerations of 0.48 g at seabed.??Design tectonic movements of 2 m (7 ft) in any direction between any two adjacent bridge pier foundations/pylons.Considering subsurface conditions and local seismicity and water depths, foundation design and construction methods were the key drivers for this project. In large part, the success of the project is owed to the unprecedented partnering and collaboration between all partners involved fostered under the leadership of Jean Paul Teyssandier and Gilles De Maublanc of VINCI Group (France) who served as lead Concessionaire and General Contractor. The joint venture’s lead Greek partners were Elliniki Technodomiki/AKTOR and J&P/AVAX. Alain Pecker of Geodynamique et Structure (France) served as lead Geotechnical Consultant/ Designer while Buckland and Taylor (Canada) served as Design Checkers with Ralph Peck and Ricardo Dobry (U.S.) as Special Advisors on foundation issues, Langan International/Langan Engineering and Environmental Services P.C. (George E. Leventis, Gregory Biesiadecki and Diane Fiorelli) served as Technical Advisor on geotechnical, geodynamic and foundation/marine construction issues."

Jan 1, 2007

By A N. Parry

In May 2018 Kasbah Resources Limited (“Kasbah”) completed an ore sorting test work program which was a precursor to releasing in July 2018 an updated Definitive Feasibility Study (“DFS”) for the Achmmach Tin Project in Morocco, which it is proposing to develop along with its joint venture partners. The testwork program evaluated ore sorting as a pre-concentration option to achieve early elimination of gangue and the low-grade component of ROM feed, thereby potentially:  Significantly upgrading the head grade of tin to the downstream processing plant.  Significantly reducing the required throughput capacity (and projected capital expenditure) of the downstream processing plant.  Reducing total consumables, power and water requirements in downstream processing.  Increasing the recovery of tin in the gravity and flotation circuit due to the higher feed grade achievable with ore sorting.  Reducing tailings tonnage, tailings cost and environmental footprint.  Using sorter rejects for mine backfill or road base applications. Key aspects of the design of the metallurgical testwork program centred around the need to ensure that samples representative of ROM ore feed (including projected mining dilution) were selected for the ore sorting testwork. The design and implementation of the ore sorting bulk testwork program is described, as well as a summary of the test work results and a discussion of the enhancement of the project economics reported by Kasbah, which led the company to adopt ore sorting as part of the proposed processing circuit in the updated 2018 DFS.

Nov 10, 2020

By William D. Klopp, Joseph R. Stephens

A substantial reduction in the 300°F ductile-to-brittle transition temperature for unalloyed chromium was achieved in alloys from systems which resemble the Cr-Re system. These alloy systems include Cr-Ru, Cr-Co, and Cr-Fe. Transition temperatures ranged from -300° F for Cr-35 at. pct Re to -75°F for 0-50 at. pct Fe. The ductile alloys have high grain gvowth rates at elevated temperatures. Also, Cr-24 at. pct Ru exhibited enhanced tensile ductility at elevated temperatures, characteristic of superplas-ticity. It is concluded that phase relations play an importarlt role in the rhenium ductilizing effect. The ductile alloys have compositions near the solubility limit in systems with a high terminal solubility and which contain an intermediate o phase. The importance of enhanced high-temperature ductility to the rhenium ductilizing effect is not well understood although both may have common basic features. CHROMIUM alloys are currently being investigated for advanced air-breathing engine applications, primarily as turbine buckets and/or stator vanes. The inherent advantages of chromium as a high-temperature structural material are well-known1 and include its high melting point relative to superalloys, moderately high modulus of elasticity, low density, good thermal shock resistance, and superior oxidation resistance as compared to the other refractory metals. Additionally, it is capable of being strengthened by conventional alloying techniques. The major disadvantage of chromium is its poor ductility at ambient temperatures, a problem which it shares with the other two Group VI-A metals, molybdenum and tungsten. For chromium, the problem is further amplified by its susceptibility to nitrogen em-brittlement during high-temperature air exposure. In cases of severe nitrogen embrittlement, the ductile-to-brittle transition temperature might exceed the steady-state operating temperature of the component. The low ductility of chromium would make stator vanes and turbine buckets prone to foreign object damage. The present work was directed towards improvement of the ductility of chromium through alloying, with the anticipation that any improvements so obtained might be additive to strengthening improvements achieved through different types of alloying. The alloying additions for ductility were selected on the basis of the similarity of their phase relations with chromium to that of Cr-Re. The reduction in the ductile-to-brittle transition temperatures of the Group VI-A metals as a result of alloying with 25 to 35 pct Re is well established.a4 the temperature range -300" to 750° F. This phenomenon is commonly referred to as the &apos;<rhenium ductilizing effect"; this term is also used to describe systems in which the ductilizing element is not rhenium. Other alloy systems which have recently been shown to exhibit the rhenium ductilizing effect include Cr-Co and c-Ru.= In order to explore the generality of this effect, alloys were selected from systems having phase relations similar to that of Cr-Re, primarily a high solubility in chromium and an intermediate o phase. The following compositions were prepared: Cr-35 and -40Re; Cr-10, -15, -18, -21, -24, and -27 pct Ru; Cr-25 and -30 pct Co; Cr-30, -40, and -50 pct Fe; Cr-45, -55, and -65 pct Mn. Seven other systems were also studied which partially resemble Cr-Re. These systems have extensive chromium solid solutions or a complex intermediate phase, not necessarily o. The compositions evaluated include the following: Cr-20 pct Ti; Cr-15, -30, and -45 pct V; Cr-2.5 pct Cb; Cr-2.5 pct Ta; Cr-20 pct Ni; Cr-6, -9, -12, and -15 pct 0s; Cr-10 pct Ir. The compositions of alloys in these systems were chosen near the solubility limit for the chromium-base solid solutions, since in the Group VI-A Re systems, the saturated alloys are the most ductile. These alloys were evaluated on the basis of hardness, fabricability, and ductile-to-brittle transition temperatures. In addition to the studies of alloying effects on ductility, an exploratory investigation was conducted on mechanical properties at high temperatures in Cr-Ru alloys EXPERIMENTAL PROCEDURE High-purity chromium prepared by the iodide deposition process was employed for all studies. An analysis of this chromium is given in Table I. Alloying elements were obtained in the following forms: Commercially pure powder — iridium, osmium, rhenium, and ruthenium. Arc-melted ingot — titanium and vanadium. Electrolytic flake — iron, manganese, and nickel. Sheet rolled from electron-bearn-melted ingot — columbium and tantalum. Electron-beam-melted ingot — cobalt. Sheet rolled from arc-melted ingot — rhenium. All alloys were initially consolidated by triple arc melting into 60-g button ingots on a water-cooled hearth using a nonconsumable tungsten electrode. The melting atmosphere was Ti-gettered Ar at a pressure of 20 torr. The ingots were drop cast into rectangular slabs and fabricated by heating at 1470" to 2800° F in argon followed by rolling in air. Bend specimens measuring 0.3 by 0.9 in. were cut from the 0.035-in. sheet parallel to the rolling direction. The specimens were annealed for 1 hr in argon, furnace cooled or water quenched, and electropolished prior to testing. Three-point loading bend tests were conducted at a crosshead speed of l-in. per min over

Jan 1, 1969

By W. F. Mullen

Within the scope of this discussion, artificial dimension stone is defined as any manufactured product used as a substitute for natural dimension stone. The history of the development of these substitute materials is reviewed briefly, representative characteristics of each product are listed, several analyses of their market position are presented, and suggestions are made for recapturing markets lost to these products and preventing additional inroads.

Jan 1, 1959

By C. M. Offenhauer

Abstract Zirconium markedly affects the formation of graphite in cast iron and may promote the formation of normal flake gaphite, fine flakes of eutectiform graphite, or spheroid nodular graphite, according to the composition of the Iron and the amount of the zirconium addition. Usually, it is employed in the form of a complex addition agent in order to facilitate its introduction and to guide its effect. The reported applications of zirconium as an inoculant for the production of pearlitic high-strength cast iron indicates that it is most effective as a silicon-manganese-zirconium alloy. Added in this form it reduces chill and minimizes zones of ferrite and eutectiform graphite. In low-sulphur cast iron, zirconium in amounts greater than 0.10 per cent tends to promote the development of eutectiform graphite. These irons are characterized by freedom from primary cementite or normal flake graphite and exhibit very little tendency to shrinkage on solidification. In hyper-eutectic low-sulphur cast iron, zirconium causes the formation of a partially nodular graphite structure. A combination of magnesium with silicon-zirconium alloy was found to produce completely nodular graphite structures without the hazards associated with the addition of elemental magnesium.

Jan 1, 1949

"Chairman: Professor E. P. PFLEIDER Rapporteur: Mr P. R. JANISCHPapers:Optimum design of an open pit by D. A. PhillipsAn open pit design system for stratiform ore bodies by L. A. J. Pronk van Hoogeveen, J. R. Cutland and M. WeirAn open pit design model by R. H. Robinson and N. B. PrennThe Chairman in opening the session highlighted the current situation in the United States of America where some 85 to 90 per cent of all mining (except for coal) is done by open pit methods, and where some 40 per cent of the coal is mined by open pit. The South African industry is, of course, dominated by the deeper level underground gold mines; however, with the aid of an extensive open-pit technology developed in other countries, South African companies arc continuing to explore possibilities of open-pit exploitation of base mineral, coal and diamond deposits. Several successful ventures are already in operation at Phalabora, Optimum Colliery, Kimberley and elsewhere, and South Africa is undoubtedly benefitting in this regard by drawing on the experience of others.The papers of this session were therefore particularly pertinent, particularly when viewed in conjunction with those presented at an earlier South African conference devoted specifically to open pit mining.Two themes dominated the discussion which followed presentation of the three papers at this session. The first related to the practicability of using the reported techniques as a tool for management, and their acceptability as such to mine management. This was, of course, not peculiar to this particular session, but rather the major point of debate over the entire conference.The second theme concerned the reliability of the initial drill hole data on which any open-pit design must necessarily be based. This gave added emphasis to the problem of practicability, for no management is likely to accept an elaborate pit design unless confidence can be placed in the ore reserve assessment.In noting these two features of the discussion, it should be remembered that all the three papers dealt largely with design and pre-planning; there was an unfortunate lack of papers or discussion on the subject of controlling the day-to-day mining of open pits, and this is an area where the potential impact which can be made by the computer is even greater.In introducing his paper, Mr D. A. Phillips pointed out that it was concerned only with optimization, and that it therefore assumed, firstly, an adequate subdivision of the orebody into ore blocks characterized by grade, rock type, structure, etc., and, secondly, an acceptable forecast of costs and mineral prices in order to generate a suitable profit matrix. However, programs dealing with these problems for both massive, disseminated and stratiform ore bodies are available to Roan Consolidated Mines. The method of optimization which he had described had been used on a region split into 28 000 blocks, for which the program used three hours of C.P.U. time on an IBM 360/40 computer. The computer design had provided a three per cent improve¬ment on a normal design of the same area."

Jan 1, 2014

By J. M. Whatley

"IntroductionIN UNDERGROUND mining operations, the mine hoist has become one of the most important and one of the most expensive single pieces of equipment. As the means of transporting men and materials to the face, broken ore to the mill, and waste to the dump, it is often the very lifeline of a mine and must operate with dependability and efficiency or the whole operation will suffer. The mine hoist has become synonymous with safety. In few other types of mechanical equipment do so many men so frequently and completely place their lives. In Canada, more has probably been done to assure safe hoisting than in most other countries, but, unfortunately, this has resulted, in many cases, in the mines having to pay a high price for equipment. Hoist manufacturers have carried out much research in recent years in the endeavour to keep down these costs and at the same time maintain or improve the efficiency and safety of their products. Broadly classified, the bases for design research are dependability, efficiency, safety, and first cost.Probably the greatest single factor influencing the design of mine hoists was the introduction of electric motor drives. It was not until about 1905 that an effective start was made in the development of electric mine hoists, and then only with machines of small size. From that time on, however, progress was rapid, as may be gauged from the fact that by 1910 one large group of mines in Johannesburg had in use, or on order, fifty-four three-phase hoists and four Ward-Leonard. type hoists."

Jan 1, 1953

By Delbert L. Keenon

The principal concepts of computer control and automation have been successfully applied in industries world-wide, The enthusiasm generated by the proponents of computer control, and the apparent mystery enveloping the techniques of computer control, have caused attention to be focused on this infant industry from all quarters. Consequently, the motivation to "computerize" may be the hope that computers will solve all economic problems. The truth remains that not only have there been monumental successes, but there have been some colossal failures. This paper will attempt to outline a generalized guide to computer control and present methods for avoiding some of the major pitfalls. Since the investment required for computer control systems has been drastically reduced in the past year, small operations will likely find that computerized process control is attractive in areas where it has never been considered before, The discussion presented here is intentionally non-technical and directed towards those who may soon find they have a possible application for a control computer. The primary purpose of computer control is to reduce expenditure and increase profits by improving the quality of product, increasing the efficiency of operation, reducing the materials and man hours required or a combination of these. Success or failure to reach the desired goal depends, to a large degree, on a well-planned approach. This includes recognizing a possible computer application, properly defining the job which is to be accomplished, evaluating computer systems, selecting a capable manufacturer, and following through with sound systems engineering and programming.

Jan 1, 1965

By Shaojun Bai

Siderite ore with high phosphorus content was reduced isothermally at 1,050° C with pulverized coal and different dosages of sodium carbonate. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energydispersive analysis of X-rays (EDAX) were used to characterize the samples. The influence of sodium carbonate on the carbothermic reduction process was investigated. Sodium carbonate and its dosage played a considerable role in the carbothermic reduction. The iron particle size in the reduced ore was below 20 µm, and fayalite was abundant without sodium carbonate additive. With a mass ratio of Na2CO3-to-ore of 5% additive, the iron particle size in the reduced ore was generally above 50 µm, and the diffraction intensity associated with metallic iron in the XRD pattern increased. The effect of sodium carbonate on the phase transformation of fluorapatite during carbothermic reduction was also addressed via thermodynamic calculations and aqueous leaching experiments. The results showed that the fluorapatite was not reduced to P2 at 1,050° C, and a portion of the fluorapatite was converted to soluble phosphate. The reduction of siderite can be catalyzed by adding an appropriate amount of sodium carbonate. This catalytic activity was caused by an increase in the reducing reaction activity of FeO and the acceleration of the carbon gasification reactions. The decrease in phosphorous content in the iron concentrate was attributed to an improvement in the separation of the iron phase from the slag phase when sodium carbonate was added and with the formation of soluble phosphate.

By Paul C. Turner

In 1998, approximately 57,000 tons of titanium metal was consumed in the form of mill products (1). Only about 5% of the 4 million tons of titanium minerals consumed each year is used to produce titanium metal, with the remainder primarily used to produce titanium dioxide pigment. Titanium metal production is primarily based on the direct chlorination of rutile to produce titanium tetrachloride, which is then reduced to metal using the Kroll magnesium reduction process. The use of titanium is tied to its high strength-to-weight ratio and corrosion resistance. Aerospace is the largest application for titanium, and titanium cost has prevented its use in non-aerospace applications including the automotive and heavy vehicle industries.

Jan 1, 2001

By V Srinivasan, P Knights, C T. Farrelly

By 2025, with the widespread industry adoption of remote operation centres and advanced analytics, mining companies will find themselves making better, more informed decisions across the value chain. Process automation will drive significant business integration and reorganisation. Better collaboration between functions will make cross value chain optimisation a reality. Wherever possible decisions will be automated, based on analytical models and embedded in an enterprise decision management (EDM) architecture. This will take care of many of the minor day-to-day or the minute-to-minute decisions that consume operators and managers today. More flexible information technologies and architectures derived from the extensions to Web 2.0 and service oriented architecture (SOA) will solve many of the integration issues of today. The ongoing business imperatives for doing more with less people will make true collaboration with partners such as mining contractors, equipment vendors, transport providers, suppliers and maintenance contractors commonplace throughout the industry. All these organisations will be linked in and share common goals and objectives in real-time while providing visibility of internal constraints and available capability, allowing optimised decisions to be made across the extended enterprise. Humans will increasingly move to a more supervisory role and will use advanced collaboration to quickly solve complex abnormal issues that span the value chain out to the extended enterprise. The open collaboration and communication models instilled in the workforce through the widespread use of social networking technologies will drive thought leadership far beyond current æbest practiceÆ thinking. This will encourage the mining industry to extract the business value from rapidly converging fields of study such as environmental sciences, neuroscience, psychology, engineering, information technology and business finance. The future of mining will see a more uniform distribution of data savvy workers between the ages of 20 - 40, forcing a change in current operations. This group will drive the adoption of ubiquitous computing, augmented reality, presence and digital labelling. The enterprise will shift from a relatively static disparate set of functions to a digitally aware, integrated and interactive environment with information available, in context and just in time, to those who need it. The networked virtual enterprise will therefore be a reality.

Jan 1, 2008

By Liao Jianfeng

The Baosteel Zhanjiang 5,050m3 blast furnaces have been built with highly independent integration and innovation technologies and represented the state of the art of the world’s huge BFs. The proper of BF1 and BF2 is designed with long-campaign technology; both BFs share the same set of stockhouse, water and PCI systems; the BCQS serial-hopper no-bell top, TRT and blower are all local equipment as applied; four top-combustion stoves systems are matched; the BFG is cleaned by fully dry process; and the automation control system for the main process is self integrated. The BFs have been started up and performing with sound indicators. Their smooth proceedings symbolize China’s huge blast furnace ironmaking technology ascending a new high.

Oct 30, 2017

By Jack S. McPartland

Historically, research on thiosulfate leaching of precious metals ores has been focused on processing of difficult to treat ores. Thiosulfate leaching of ores and concentrates containing sulfide minerals, copper, manganese and preg-robbing carbon constituents has been evaluated. Cyanide leaching is generally considered an efficient, environmentally acceptable means for processing of non-refractory precious metal ores, Consequently, commercial processing of finely disseminated, oxidized precious metal ores is normally accomplished using alkaline cyanide leaching. Recent changes in regulatory climate have, however, called into question the acceptability of cyanide leaching in a number of locations worldwide. In some cases where the use of cyanide is being questioned, thiosulfate leaching may provide an acceptable alternative. Developments in thiosulfate leaching of precious metal ores are reviewed in this paper.

Jan 1, 1999

By Hevina S. Dashwood

This paper proposes to build on my previous research (Dashwood 2012), which analyzed how and why the norm of sustainable development became institutionalized in the global collaborative corporate social responsibility (CSR) initiatives of major mining companies. Since the late 1990s, the majority of major global mining companies have employed the norm of sustainable development to frame their individual CSR policies and to inform industry collaboration at the global level through the International Council on Mining and Metals (ICMM). This paper proposal seeks to address lingering questions from that research, by developing an explanation for how the normative frame of sustainable development has translated into specific CSR standards adopted by the mining industry. Preliminary findings suggest that, although the global mining industry has reached broad consensus on the meaning of sustainable development in the context of mining, there remains considerable variation between mining companies in terms of which specific global standards they adopt. As members of the ICMM, major mining companies are required to report according to the Global Reporting Initiative (GRI) indicators relevant to mining, and there has been wide-spread up-take of the ISO 14,001 environmental management system standard. However, other global standards, such as the International Finance Corporation (IFC) Performance Standards and the Extractive Industry Transparency Initiative, have not been uniformly adopted by the mining industry. What explains this variation? The paper employs a three-level institutional framework (rational choice institutionalism, historical institutionalism and the ?new? institutionalism in organization theory) to explain the influences on the adoption of CSR standards in the global mining sector. Existing research confirms that institutional context is an important factor in explaining CSR adoption in the mining sector (Dashwood 2012). Are similar forces at work in explaining the variation in adoption of specific CSR standards? A three-level institutional analysis lends itself to uncovering influences both external to mining companies (such as pressures from stakeholders), as well as internal company dynamics (such as managerial discretion). Furthermore, the framework can incorporate dynamics operating at the global level (such as isomorphism), the national level (such as the regulatory regime) and the local level (such as community needs and environmental challenges). The theoretical significance of this framework is that the influences on CSR adoption are more complex than can be explained in a single approach (such as narrow rational choice/cost benefit explanations). On a practical level, insights into how global standards get interpreted and acted upon by individual companies could lead to the development of more appropriate and effective global standards.

Aug 1, 2013

By Robert W. Holliday

Natural resources are the reservoir from which society draws its material sustenance. Although there is a growing awareness of the need for aesthetic resources such as space for recreation and natural beauty, the basic resources are soil, air, water, and minerals including fuel. Minera&apos;s and all sources of energy gain in relative importance with advancing technology and expanding industrilization. In the highly industrialized economy of the United States, almost every aspect of man&apos;s life is touched in some way by a product of, the mineral; industries. Agriculture owes much of its productivity to mineral-based fertilizers, insecticides, and mechanical equipment. Modern construction, manufacturing, communications, and transportation are all dependent on nonmetallic minerals, metals, and fuels. Throughout history, those nations with access to minerals, and the technology for using them, have gained ascendency. Before World War II the leading powers also were, leading coal producers. In order of declining rank the five leading&apos; coal producers were the United States, the United Kingdom, Germany, the USSR, and Japan. That the military victory went to the side with the greater&apos; capacity to convert iron and coal into tools of industry, and weapons, is&apos; more than coincidence. It is a fundamental&apos; fact of existence. It is axiomatic that the United States must have a continually increasing supply of minerals if we are to meet the needs of our burgeoning population for a comfortable standard of living and for national security.

Jan 1, 1968

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread-sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin. Computerized search Computerized search approaches represent crude first attempts at letting the computer design the blend. Unfortunately, the blends found by these programs are very often less satisfactory than those developed manually. The way these techniques work is that they design, according to some predesigned pattern, a number of different blends and then quickly evaluate them. It is then straightforward to select the best from this sample set. The quality of the results depends on the number of blends designed, the way they differ from each other (the search procedure), the number of sources available, the number of quality specifications, and the severity of the specification limits. Good results are usually obtained for small, simple problems. At best, the results obtained are inconsistent from one blend to the next. Programs of this type are advertised in the mining literature. They usually mention how many different blends are evaluated, making it clear that this is more than can be tried manually. Expert systems Expert systems use a source of information known as a knowledge base. The knowledge base, usually a set of if-then rules, attempts to reconstruct the deductive reasoning process of an expert in some job capacity. For coal blending, the usual trial-and-error process has an easily recognized pattern of rules that are followed to try to find a better blend. By following these rules, it is possible to home in on the best blend without the exhaustive search required by the previous method and without the manual manipulation of the spreadsheet approach. The use of an expert system accomplishes this. One of the rules may say something like "if BTU is out of spec, then add more in the blend from a source having a high BTU and subtract some from a source having low BTU." In other words, it goes through the trial-and-error process. The process continues until all specifications are achieved and can continue further to try to optimize the cost. Of course, less simplistic rules are also needed. One set of rules would determine maximum changes in the tonnage added or deleted to the blend or from any one source. Other rules would be needed to determine which quality to improve if two or more are out of spec. At this level, the process of building the knowledge base provides the engineer with a deeper understanding of his or her own thought processes. The advantage of obtaining better blends is clear for this approach. Two more advantages should also be apparent. One is that it follows the same common sense logic that is used when doing the blends by hand or by spreadsheet, making it easy to understand. The other is that, like the search procedure, it designs the blend rather than just analyzing manually designed blends. Thus, it has all the good features of both approaches discussed thus far while providing improved results over each. A final advantage is the ease of use and ease of development. The expert system shells that are on the market are very easy to use and can be run on microcomputers. Linear programming Linear programming is an algebraic tool that solves a set of linear equations to yield an optimal solution to a problem. The optimal solution is based on the linear model so the results are only as good as the ability of the linear model to accurately portray the reality of the problem situation. It is fortunate for the coal blending problem that a linear model can be devel¬oped that reflects exactly the problem that is required. Unfortunately, the mining industry has been slow to use this tool. Coal blending applications available that use linear programming take one of three forms. The first, requiring exper-

Jan 12, 1988

By Xiaowen (Wendy) Ma, Hans Liang, Xiaoying Chen, David Way

"The mineralogical characteristics of the process streams provide key indicators to the potential improvement in the metallurgical performance. Therefore, the process mineralogy and diagnostic metallurgy have been widely used as a tool to assist the metallurgists at the operating plants. The challenge of this study was then how to characterize the diagnostic flowsheet of the minerals of interest in the process streams across the flotation circuit. The investigation from this study indicates that the minerals chematic flowsheet can visibly demonstrate the sources that caused the gold losses during the mineral processing.In this paper, we present studies of the flotation process stream samples, representing the feeds, intermediate products, final concentrate and final tails, which were produced from the flotation concentrators of Mt Carlton mine in Queensland, Australia. This study was focused on characterizing the process streams and learns how the gold in the process streams was associated with other sulphide minerals and host minerals on a size by size basis. The automatic QEMSCAN/MLA Particle Mineral Analysis (PMA) and Trace Mineral Search (TMS) were applied to identify the minerals and to detect the gold in the sized fractions of process streams. The Laser Ablation ICP-MS (LA) spot analysis, QEMSCAN EDS spot analysis and electron microprobe spot analysis were employed to identify and quantify there fractory gold concentrations in the sulphide minerals, like pyrite, and the elemental concentrations of visible gold grains. The diagnostic flowsheet of gold recoveries by the process streams, by mineral association classes and by the particle sizes were generated and discussed."

Jan 1, 2017

By A. M. Sarem, J. M. Campbell

Molecular refraction is introduced as a new and improved third parameter for prediction of the PVT behavior of hydrocarbon systems. This parameter, characterizing the complex as well as the pure hydrocarbon systems (1) is a direct measure of London dispersion forces which affect the PVT behavior; (2) can be measured directly, accurately and easily for complex as well as pure hydrocarbon systems; (3) varies significantly between the reference substances thus allowing accurate interpolation of PVT properties; and (4) has a fundamentally sound basis. Molal average molecular refraction was used with the pseudocritical mixing rule proposed by Leland and Mueller to predict the molal volume of liquid and vapor for 84 published data points on nC4-nCI0, Cl-nC5, Cl-nC4-nC10 systems in the region of coexisting vapor-liquid and at the critical point. The same technique was applied to predict the densities of liquid hydrocarbon mixtures in the two-phase and single-phase regions near the critical point for seven different systems each having different properties of the heptanes-plus fraction, but all simulating the fluids of either gas-condensate or volatile oil reservoirs. A modification of the Leland-Mueller mixing rule for the determination of pseudocritical properties is also presented which yields more accurate liquid density predictions than the original form when used with the proposed third parameter. INTRODUCTION The PVT behavior of multicomponent systems has received widespread attention in the literature in recent years. A large portion of the reported work has stemmed from attempts to overcome the inherent difficulties encountered when using the standard compressibility-factor chart which shows 2 as a function of reduced temperature T, and and reduced pressure p,. This chart assumes that z, is constant for all systems. The error in this assumption is not pronounced for pipeline-type gases high in methane and low in heavy ends, particularly when contained at moderate pressures. For such gases the error in the calculated z is usually less than 2 to 3 per cent. However, the reliability of this approach becomes somewhat nebulous for gas condensate and volatile oil systems at high pressure. One logical approach has been to recognize the variation of 2,. This idea was first suggested by Meissner and Seferianl and used by Lyderson, Greenkorn and Hougen2 to prepare extensive tables of thermodynamic properties. Other third parameters have been proposed by Stockmeyer, Kihara, Riedel, Lightfoot, Bloomer and Pitzer. These were tested by Satter and Campbel13 for many gas mixtures and it was shown that they were inter-related. All of these third parameters have a common fault — they cannot be directly evaluated for the heptanes-plus fraction. Consequently, one necessary requisite of an improved method for predicting the density of multicomponent hydrocarbon systems, was development of a third parameter that could be evaluated for that fraction. PREVIOUS MULTICOMPONENT DENSITY PREDICTION METHODS Sage and Lacey4 suggested a method of using partial molal volumes for computing the density of hydrocarbon gas mixture for pressures to 3,000 psi. In this technique, they approximate the complex multicomponent gaseous mixtures by a quarternary system of methane, ethane, propane and butane. Sage, Hicks and Lacey5 suggest a method of using partial molal volumes for computing the density of hydrocarbon liquids. The results agree within 3 per cent of the experimental values. However, the composition range is limited to about 10 per cent by weight of methane. Consequently, this correlation does not cover the low-molecular-weight liquid similar to natural gasoline and high-pressure gas condensates.

Jan 1, 1966