Search Documents

By D. Nie, M. Ren, T. Mo

This paper studied the phenomenon of room temperature creep deformation at crack tip and its effect on fatigue crack growth rate of a X-70 pipeline steel using compact-tension (CT) specimen on a MTS 810 testing machine. Time-dependent deformation at the crack tip under constant load was observed in this steel at room temperature and the amount of deformation produced was seen to depend on loading rate and the magnitude of stress intensity factor. It is found that there exists a critical stress intensity factor below which the deformation decreases with time when the applied load remains constant. It is also found that the occurrence of room temperature creep obviously affects the subsequent fatigue crack growth rate. The observed behavior was explained based on dislocation theory.

Jan 1, 2005

By David G. Meadows

During the last decade Antofagasta Minerals? Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.

Jan 1, 2012

By Peter Faust

"The south access road to San Francisco’s Golden Gate Bridge, known as Doyle Drive or Presidio Parkway, needs to be replaced. Built in 1936, it is the primary highway and transit linkage through San Francisco between counties to the north and south. The roadway is tucked into the natural contours of the Presidio and the Golden Gate National Recreation Area, one of the nation’s largest urban parks.The old steel truss structure will be replaced by a new concrete cast-in-place bridge. The foundation design of the new bridge is based on drilled mono shafts below each bridge column. Most shafts required large diameter permanent steel casing installed under strict vibration limitations since several historic landmarks are near the project alignment. Malcolm Drilling decided to use the largest oscillator in the world to install the piles.The area occupied by the Presidio is generally hilly, sloping down northwards to San Francisco Bay. In the western half of the project route, two bluffs rise steeply to about 80 ft (25 m). The bluffs are separated by a valley 60 ft (18 m) deep and 1,500 ft (457 m) wide, which is spanned by the old and new bridge. Overburden soils in this valley are made up of artificial fill, slope debris, ravine fill and Colma Formation, a fine to medium-grained sand unit with clay beds. The Bay Muds encountered in the project area are typically soft clayey silts, becoming medium stiff with depth.The basement rocks underlying the overburden belong to the Franciscan Formation, described as shale, sandstone, serpentine and greywacke, it is extremely variable in hardness, fracturing and weathering. The material can vary from very hard to very soft, can be slightly to very intensely fractured and almost not weathered, to totally decomposed within relatively short distances both laterally and vertically. Rock strength can vary from too weak to be tested to serpentine layers with unconfined compressive strength of 15,000 psi (103MPa) or higher. Groundwater levels in the area are typically no more than 10 to 20 ft (3 to 6 m) below the ground surface."

Jan 1, 2012

By D. S. Harper, C. O. Carman

A German coal planer was put in operation in the Keystone mine of the Eastern Associated Coal Corp. , Keystone , W. Va . , in August 1960 . At present , the planer is mining in the fourth panel . The blocks of coal mined were 340 by 1,900 feet in panel 1 , 340 by 1,660 feet in panel 2 , 590 by 1,900 feet in panel 3 , and panel 4 , currently being mined , is 590 by 1,900 feet . Almost one- half million tons of coal have been mined from these four panels . An 11 - man crew handles the complete planer operation and produces an average of 500 tons of clean coal per shift . Self - advancing hydraulic props are used to support the roof over the entire face . Roof control and action on all of the panels has been highly satisfactory . During periods of extreme pressure , some additional support is required in the tail entry where evidence of weight from the retreating longwall extends about 200 feet outby the face . The time lost from production by moving equipment between panels has been reduced steadily . The move from panel 3 to panel 4 required 5 days , but it is believed that even that time could be reduced .

Jan 1, 1963

By Benito Barbabela e Silva

O pelotamento é a mais complexa etapa de aglomeração de finos de minério de ferro. Sua resposta é naturalmente oscilante, sendo bastante influenciada pelas características físicas obtidas nos processos de beneficiamento mineral que a precedem e tem papel crucial para a etapa de tratamento térmico de sinterização à jusante. O presente trabalho aborda o processo de classificação de pelotas verdes, sólidos singulares de aspecto deformável e pegajoso, em peneiras de rolos por modelamento por aplicação de Método dos Elementos Discretos. Esta técnica mostra-se como uma importante ferramenta pois supera as limitações impostas na modelagem física (quantificação e identificação de fluxos por ausência de instrumentação em escala industrial, amostragem sem representatividade) ao reproduzir de forma verossímil as repostas do sistema para importantes variáveis de controle: comprimento de gap, umidade, dispersão de tamanhos e resistência das pelotas.

Oct 30, 2017

By C. F. Allen, G. B. Walker

The sink-float methods designated by heavy-media separation processes were pioneered by C. Erb Weunsch for the treatment of base metal ores as an improvement over jigs. The work of Weunsch was further developed by Victor Rakowsky and The American Zinc, Lead and Smelting Co. Early in the development of the processes, the inherent unsuitability of galena as the solid constituent of the medium was recognized and ferrous media amenable to magnetic recovery and control were developed. The high efficiency and low cost of magnetic recovery and cleaning of ferrous media regardless of particle size, slime contamination, or surfacial oxidation had led to the adoption of ferrous media by all of the sink-float plants operating under the heavy-media separation processes patents controlled by American Zinc, Lead and Smelting Co. Approximately 2,000,000 tons of base metal and nonmetallic minerals are treated each month by these methods. Heavy-media separation processes are a modern practical and economical adaptation of the well-known laboratory procedure for separating a mixture of two solids by immersing the mixture in a liquid having a specific gravity intermediate the specific gravities of two solids. The lighter solid floats while the heavier sinks. This method of separation has been attempted on a commercial scale, but the high loss and high cost of the organic liquids halted the development of the process. Many attempts have been made to simulate a heavy liquid by using a suspension of a finely divided solid in water. If the solid phase of the suspension is ground fine enough, the suspension can be made stable or so slow settling that a substantially uniform specific gravity can be maintained from top to bottom of the bath. However, any material separated by such methods will inevitably be contaminated by some slime which will eventually accumulate in the bath and cause a viscous medium at the expense of separating efficiency. Therefore, it is necessary to provide means for continually cleaning a portion of the medium to eliminate slime at the same rate at which it is introduced to the medium. The problem of efficiently cleaning the medium limits the minimum grain size of the solid of the suspension in the case of the Chance sand process for cleaning coal, because de-cantation is the only cleaning method available. If the sand is too fine, it will be lost along with the slime. Therefore, coarse sand must be used, and to maintain a semblance of a uniform suspension, it is necessary to use strong rising water currents. The combination results in a separation based more on hindered settling classification than on sink-float principles. As previously mentioned, galena was used as the solid constituent of the medium during the early stages of the development work. The high specific gravity of galena made it suitable for the preparation of medium for high specific gravity separations. Galena can be cleaned by either decantation or by froth flotation. As with sand, de-cantation limits the minimum particle size of the media that can be cleaned without excessive loss. Froth flotation for cleaning galena medium has been used, but the problem of floating fine galena that has been exposed to extensive oxidation is well known to be a most difficult one. Last year the largest heavy-media plant m the world, and the second plant to be installed, converted from galena medium to ferrous medium despite the fact that the ore contains galena which can be used as medium. The change to ferrous medium has been beneficial in many ways. Today all the heavy-media plants have been converted from galena to ferrous media. Unquestionably, ferrous media have the widest application of any media developed, for the following reasons: 1. Ease of recovery and cleaning by magnetic means. Particle size or surface condition not a factor. 2. Low consumption per ton of ore treated. 3. Resistance to abrasion. 4. Widest range of media densities, including higher workable densities (1.25 to 3.4) than have been found possible with nonferrous media. 5. Space required for recovery and cleaning of ferrous media is considerably less than that for nonferrous media. 6. Ferrous media require lower capital investment and operating costs for media recovery and cleaning. Advantages of Heavy-media Separation Processes Heavy-media separation processes offer the following positive advantages, amply demonstrated on a wide variety

Jan 1, 1950

By H. C. Theuerer

GeC14 may be purified by extraction with HCI and chlorine. The process is as effective for the removal of AsCI:, as the more cumbersome distillation methods usually used for this purpose. GERMANIUM for semiconductor use contains impurities at levels no higher than a few parts in ten million. Material of this quality is obtained from highly purified GeC1, by hydrolysis to the oxide and reduction of the oxide in hydrogen. When purifying GeCl,, AsC1, is the most difficult impurity to remove. This is usually accomplished by multiple distillation procedures.1-3 AsC1, may also be removed from GeC1, by extraction with HC1.1-4 Reducing the arsenic to low concentrations is not practicable, however, because of the large number of extractions needed. This paper discusses a new method for the removal of arsenic from GeC1, by extraction with HC1 and chlorine. The method is rapid, leads to little loss of germanium and is at least as efficient as the distillation procedures currently being used. Theory of Extraction Procedures In the simple extraction of GeC1, with HC1, the following reaction occurs ASCl8G8C1 D AsCl3rc1 at equilibrium CA/Cn= K, where K is the distribution coefficient, and C, and C,, are the molar concentrations of AsC13 in HC1 and GeCl,, respectively. The materials balance equation for this reaction is VACA + vncn = VnC,, where V, and Vn are the volumes of HC1 and GeCl4, respectively, and C, is the initial concentration of AsC13 in GeC1,. From this it can be shown that for multiple extractions where C,, is the concentration of AsC13 in GeC14 after n extractions, and r is the ratio of V, to V,,. It is assumed that r is maintained constant, that equilibrium is established during each extraction, and that K is independent of the AsCl3 concentration. By saturating the system with chlorine, the following reaction occurs in the aqueous phase AsCl3 + 4H2O + Cl2 D H5AsO4 + 5HC1 at equilibrium K' = ------------ ai - a4 h2u - aet2 where a is the activity of the various components. The effect of this reaction is to reduce the concentration of the AsC1, in the aqueous layer and, therefore, to promote further extraction of this component from the GeC1, layer. If the arsenic acid remains entirely in the aqueous phase, the net effect of this reaction is to promote the removal of arsenic from the GeC11. The materials balance equation for extraction with HC1 and chlorine with the foregoing reaction is, then, VaCC + VACA + VACn = VnCo where C,. is the molar concentration of H3AsO, in the HC1. With the added assumptions that the activities of AsC13 and H8ASO4 in the aqueous phase are equal to their molar concentrations, it can be shown that for n extractions Cn/Cu = (1/rkK + rK + 1) n where k - K1 a4h2o - acl2/aoncl. It can be seen by comparing Eqs. 1 and 2 that if k is large, the removal of AsC1, by HC1 extraction will be greatly improved by the addition of chlorine. Dilution of the HCI used in the extraction with chlorine would also favor the separation. This, however, would increase the loss of GeCl,, which is undesirable. Experimental Procedure Germanium prepared from oxide of semiconductor purity is n-type with resistivities greater than one ohm-cm. The resistivity is controlled by the donor concentration, which is —lo-: mol pct. Germanium prepared from material with added arsenic will have lower resistivity commensurate with the arsenic concentration. With such material, at arsenic concentrations above 10-1 mol pct the resistivity is controlled by the added arsenic, and effects due to other impurities initially in the oxide are negligible. In this investigation GeO, of semiconductor purity was converted to GeCl,, and -0.01 mol pct As was added. This material was used for the extraction experiments and the purification attained determined by a comparison of the resistivity data for samples of germanium prepared from the initial and purified GeC1,. A method for calculating the arsenic concentration from the resistivity data is discussed later. The details of the experimental procedures used are as follows: Two hundred and thirty cu cm GeC1, were prepared by the solution of GeO, in HC1, followed by

Jan 1, 1957

By Anu Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Miner Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the NIOSH Bruceton Experimental Mine was pressurized using a 1.1 m (42 in) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

By Fazel G. Jahromi, Ahmad Ghahreman

"Several studies were performed on the atmospheric leaching of copper sulfide minerals in the presence of activated carbon and a new catalyst, AF 5. AF 5 is a carbon based catalyst with similar properties to those of activated carbon however much better mechanical properties. The activated carbon surface chemistry has been investigated in various studies; however the connection of the surface chemistry of activated carbon and AF 5 with the sulfide minerals during the atmospheric leaching process is not well-understood yet. Based on the surface analysis, AF 5 showed higher surface area than activated carbon (AC). Adsorption and oxidation of copper, arsenic and iron ions in the presence of different activated carbon were investigated. Adsorption properties of both catalysts were similar and 18-24% of iron, 12-18% of copper and 10% of arsenic adsorbed on the catalysts surface form 5 g/L Fe(III) and Cu(II) and 2 g/L As(III) at 80°C. In oxidation experiments, both catalysts reduced Fe(III) and Cu(II) ions and re-oxidized the reduced species in the presence of oxygen and oxidized As(III) ions. The addition of oxidizing ions can enhance the oxidation process kinetics and increase the catalytic capability of carbon.INTRODUCTION Hydrometallurgical processes of copper sulfide concentrates are under development and various different methods have been proposed to increase the atmospheric leaching rate of copper sulfide minerals. These methods include using different media, reagents, and catalysts. Among different methods, leaching of the copper sulfide minerals in the chloride media has some advantages over sulfate media. Smaller scale of operation, increased leaching rates, and lower sulfate formation are some of the benefits of the chloride leaching media over other similar media. Moreover, using ferric and cupric ions as oxidants and utilizing activated carbon as a catalyst has been proven to enhance the leaching rate of copper sulfide minerals effectively. Activated carbon (AC) and AF 5 (micro porous carbon based catalyst) are two of the most efficient and practical catalysts in copper sulfide leaching processes. AC can enhance the copper recovery of enargite in chloride media from 69% to 92% after 96 hours of leaching under the similar conditions (Jahromi & Ghahreman, 2016). It has been shown that AC at acidic pH can generate hydrogen peroxide in the presence of oxygen which can leach copper minerals (Ahmumada et al., 2002)."

Jan 1, 2017

"Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor a production blasting in a quarry. The production blast consisted of double-decked explosive loads in 155 mm (6 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsionexplosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and thevibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of micro-cracks along the joint surface as a function of the vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring."

Jan 1, 2017

By B Mohanty, A Siamaki, K Esmaeili

Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor production blasts in a limestone quarry. The production blast consisted of double-decked explosive loads in 125 mm (5 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsion explosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and the vibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of microcracks along the joint surface as a function of the relatively low vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring.

Jan 1, 2017

By Gibson J.

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 3rd June 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.72-84, included a written contribution by Parfitt I.C. and the author's written replies to this and previous discussion

Dec 1, 1916

By Gust Van Lysebetten, Monika de Vos

The objectives of monitoring geotechnical structures can be very diverse, including optimisation of the design, quality control, long term performance assessment, and approval of innovative execution techniques. In this context, new measurement techniques, based on optical fibres, offer the possibility of accurate strain and temperature monitoring with very small sensors and limited numbers of cables. This paper briefly presents optical fibre sensing techniques and illustrates their application to geotechnical structures by means of some projects, carried out by the Belgian Building Research Institute (BBRI).

May 1, 2022

By V. Panayotov, M. Panayotova

"Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals and their ability to float is extremely important. The approach presented in this work allows us to draw predictive models for an effective flotation, suitable choice of reagents regime and expected technological results before the minerals enter the flotation process. Attempts to adjust the technological regime in already begun flotation are often unsuccessful because the basic physicochemical processes have already taken place. Mineral processing can be optimized on the basis of objective and basic parameters, decisive for the efficiency of the process - the state of the surface of the mineral; assessment of: minerals flotation ability, the need to apply and the type of needed pretreatment, and expected technological results. The theoretical foundations of such an approach are presented in the work, as well as supporting them experimental results, and information on practical implementation in lead-zinc and copper-pyrite ores selection.INTRODUCTIONIncreasing impoverishment of ores of nonferrous metals incoming to the flotation and rising costs for obtaining the final product lead to the inevitable question - will the mineral processing process be beneficial economically, technologically feasible and environmentally safe and what is the way to improve its efficiency. Some of the possible solutions are already in practice - new more efficient and less energy consuming flotation machines and equipment, new - more efficient and selective reagents, new combinations of flotation regimens, and so on.Finding a reliable relationship between fundamental properties of minerals of non-ferrous metals (sulphides and oxides - most of them with semiconductor properties) and their ability to float is extremely important. This is the subject of research, started in the 60s of the previous century and continuing to the present day. Such dependence would enable a realistic assessment of flotation ability (flotability) of minerals before their flotation processing. The basic dependence, displayed by the researchers as Hoberg (1975), Chanturia and Shafeev (1977), Chanturia and Lunin (1983), etc., represents a relationship between bulk properties of minerals and their flotability, considering especially the concentration of the main charge carriers, namely electrons or holes. The bulk properties are practically constant for minerals from a given field. But the 'main arena' of the flotation process is actually the mineral surface (Carta, 1970; Rao, Labonte, & Finch, 1992; Panayotov, 1999; Rao, 2003; Hu, Sun & Wang, 2010). Therefore, we introduce a methodology for studying the surface of minerals, which methodology gives the degree of semiconductor bands bending on the surface and respectively - the charge of the mineral surface and its ability to interact with reagent-collector. The latter can be used to select the most optimal reagent for the corresponding mineral."

Jan 1, 2016

By John N. Murphy

INTRODUCTION It's a pleasure to be with you and to share in this opening session for the 27th Annual Institute on Mining Health, Safety, and Research. As we come together today, I would like to reflect for just a moment on the past Institutes. Much of the progress in Mine Health and Safety has been the subject of presentations and discussions at the previous Institutes, either by identifying the issues, proposing techniques to overcome the problems, or presenting new findings to address important issues for the mining industry. May I extend our thanks and congratulations to VPI and to the planners and organizers of all of these Institutes for their important contributions to our mutual goals of improving mine health and safety. In the time available today, I would like to accomplish two objectives: 1. Provide my assessment of the current status of the Mining Health and Safety Research Program; and 2. Share with you the continuing need and direction for the Mining Health and Safety Research. MINE HEALTH AND SAFETY RESEARCH TODAY Mine Health and Safety Research was conducted formerly at four geographical locations within the USBM, specifically: Pittsburgh, Spokane, Twin Cities, and Denver. Although the Twin Cities and Denver Centers were closed, we have been successful in relocatingfmaintaining much of the core competencies to conduct a responsive, multidisciplinary Mine Health and Safety Research Program. The current staff at Pittsburgh and Spokane directed toward Health and Safety Research totals 397. This includes Lake Lynn Laboratory, about 60 miles southeast of Pittsburgh, where large-scale mine fire and explosion research is conducted. With the closures and transition we have worked to maintain the core competencies necessary to address Health and Safety issues. In some cases we have made arrangements to provide the requisite core competencies through external organizations. An example is the reassignment of the diesel particulate instrumentation capability from Twin Cities to Pittsburgh. In the case of diesel emission control, due to the cost of relocating laboratories and the lack of the appropriate skills at Pittsburgh or Spokane, the emission control laboratory is now being operated in Minneapolis through a contractual arrangement with the University of Minnesota.

By Wilhelm Rohn

When a metal solidifies, gas, initially present in solution, may be concentrated at the grain boundaries, leading to brittleness, or it may form solid compounds which, if localized at the grain boundaries, impair the properties. On the other hand, the solid compounds formed sometimes distribute themselves more or less uniformly, and hence may be relatively harmless. If metallic oxides are heated under a partial oxygen pressure less than that corresponding to the dissociation pressure of the oxide in solution in the melt, they will decompose and oxygen will tend to be eliminated from the melt. This paper presents data on the partial oxygen pressures of copper and nickel oxides over a wide range of temperatures; it also presents data regarding the amount and nature of the gases evolved in the vacuum melting of a 3500-kg. charge of nickel-chromium alloy and gives test values indicating the improvement in impact values ascribed to vacuum melting. The results of commercial experience with a 4-ton vacuum melting and casting furnace indicate that this method entails an increase in cost of about 10 cents per pound of ingot over orthodox practice, which may be justified for special products and may be lowered if hot metal is charged into the vacuum furnace. DISCUSSION (Howard Scott presiding) J. H. ScafF, New York, N. Y. (written discussion).—In the section of Dr. Rohn's paper describing the effect of melting -metals in vacuo, he says, "In this way plain copper, nickel and iron may be easily purified. For example, vacuum-melted copper does not contain any oxygen and for this reason it is never sensitive to hydrogen embrittlement." This statement is contrary to the results of our experiments at the Bell Telephone Laboratories on the effect of vacuum melting on the properties of copper. Several 150-gram samples of tough-pitch copper were melted in a vacuum of the order of 1 X 10-5 to 1 X 10-6 mm. Hg for 2 hr. Portions of the ingots obtained were swaged to 0.100 in., then drawn to wire 0.050 in. in diameter for physical and

Jan 1, 1933

By Peter Heine

Diavik Diamond Mines Inc. (DDMI) has treated systems development as an integral part of the construction project when it built Canada?s second diamond mine. Fully aware that the proper collection and processing of operational data is needed to drive business decisions during production and planning, key Performance Indicators (KPIs) were defined to effectively manage operations when the mine went into production. The Production Information Management System (PIMS) allows KPIs to be measured, reported, and transferred to other systems in a reliable and convenient manner. PIMS provides a mechanism to collect real time production data from the various control systems around the site and acts as a tool to ?drill-down? and establish the important cause-effect relationships that impact the value of a KPI. Thus PIMS provides a data collection, storage, management, and an environment in which cause-effect relationships can be analysed and statistically verified. This understanding of the real cause-effect relationships, close to the source of the data and in the context of the operation, can be used to improve both operations and maintenance performance. The PIMS includes the PI Database implementation, its associated external interfaces with the various Control Systems, Cleaning Packaging Weighing System, Environmental System, Enterprise Asset Management (EAM) System, and Diamond Tracking System (DTS), as well as laboratory data collection, custom applications (downtime tracking, data reconciliation) and user clients. The interface with the EAM system provides material flow quantities and equipment availability on which the plant performance reports are based. The transfer of equipment usage to the EAM system is fed into the maintenance notifications and work orders functionality in the EAM. The environmental system interface provides the mechanism for capturing water consumption data required to generate the various regulatory reports. The interface to the cleaning-packaging-weighing system provides the mechanism for capturing batch data for transfer to the DTS for diamond product tracking at the production splitting facility in Yellowknife. The PIMS lab application provides a means of getting sample data into the system for critical metallurgical metrics, and the data reconciliation application provides a means of manually verifying the data before it is published or passed onto other systems.

May 1, 2003

By Oliver Bowles

In 1943 the Bureau of Mines began a review of trends in consumption and prices of the more important nonmetallic minerals. The first report covering building materials4/ appeared in December of that year. The present paper, which deals with chemical raw materials and fertilizers, is the second of the series. The 34 years from 1910 to 1943, for which statistics are presented herein, comprise periods of uneventful peace, unparalleled prosperity, industrial depression almost to the point of stagnation, and two wars of world proportions.

Jan 1, 1945

By Liu Xinghua

Yuanjiacun iron ore located in Shanxi province of China has finely disseminated grain size and contains refractory iron-bearing silicate gangue minerals such as chlorite. Therefore, a large amount of secondary slime (the content of -10µm fraction was up to 32.92%) was produced inevitably in fine grinding process, and chlorite was also enriched in concentrate from the content of 4.3% to 14.8% after high intensity magnetic separation. These two characteristics result in the difficulty to deal with Yuanjiacun iron ore by flotation. In this test work, contrast tests between single reverse flotation and selective flocculation desliming-reverse flotation were conducted on Yuanjiacun iron ore. The test results show that after selective flocculation desliming, the iron grade of cationic reverse flotation concentrate increases by 6.15% and the recovery increases by 7.25%; the iron grade of anionic reverse flotation concentrate also increases by 2.15%. Furthermore, analyses of grain size composition and mineral composition were carried out on separation products, the results indicate that selective flocculation desliming plays a dual role of optimizing grain size composition of flotation feed and removing iron-bearing silicate gangue minerals (chlorite) effectively.

Sep 1, 2012

By P. Lafleur

All indications point to a growing market for thermal coal in Japan as part of the country's current energy policy formulation process. The Ministry of International Trade and Industry forecasts imports of 16 million tons a year in 1985 and 40 million tons in 1990-a twenty-fold and forty-fold increase over the present level. This potential reflects Japan's over-all serious and increasing concern for security of energy supplies and its resultant need to seek alternative sources. Nuclear power will be the main alternative source, but, because it is expected that its development will be slow, imported thermal coal will assume greater importance. Canada, with large resources of all types of coal, could fill a portion of this market. Thermal coal could come from specific thermal coal developments or from metallurgical coal mines, which usually produce a certain amount of coal not amenable to coking, but suitable for power purposes. However, penetration of this Japanese market by Canadian thermal coal will depend on the resolution of a number of problems. On the demand side, siting, environmental aspects, the need for a coal unloading and trans-shipment centre, and the added cost of installing coal-fired stations could be major constraints. Although Canada has ample high-quality resources, any new development tied to the Japanese market will require improvement in prices to cover the high costs associated with transportation, the construction of new mines and the provision of new infrastructure.

Jan 1, 1979