Search Documents

By D P. Blair

Various analysis techniques are used to determine the nature of a large seismic event that was triggered by a mass blast in an underground mine. This event was recorded by surface accelerometer arrays whose output was doubly integrated using a stable filter to determine the dynamic displacements. The peak dynamic displacements during the blast were 0.09 mm, and during its latter stages, this blast induced a seismic event having a peak dynamic displacement more than ten times larger at 1.26 mm. Polarisation analysis, based on the complex covariance matrix, showed that the seismic event was caused by movement of a known underground fault, close to the blast, which radiated most of its release motion as a shear-horizontal (SH) wave. The change in frequency content with time for the blast and seismic event was initially determined using the Fourier-based reassigned S-method. This analysis showed that the large amplitude seismic event had frequency content significantly lower than that of the blast. Nevertheless, this Fourier technique still retains the problems associated with short time windows as well as the fact that most realistic signals are non-stationary. In order to eliminate such influences, the more recently developed empirical mode decomposition (EMD) was used to obtain the intrinsic mode functions (IMF) of the seismic wave propagation. The EMD vibration analysis showed that each IMF generally exhibited distinct frequency changes throughout the blast and a significant reduction in frequency throughout the subsequent event. It is shown that most of the energy of the seismic event is contained in IMF modes 2, 3 and 4 of the SH wave; the high-frequency first mode (IMF1) contains little energy. Such modal analysis is not possible using standard Fourier methods.CITATION:Blair, D P, 2015. Dynamic displacements from a blast-triggered seismic event, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 203–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Corby G. Anderson, Caelen D. Anderson, Patrick R. Taylor

"The United States contains a variety of domestic rare earth element mineral sources containing such as ancylite, bastnasite, monazite, and xenotime. Research has been performed to investigate the fundamental surface chemistry involved in the froth flotation of these minerals, and apply the knowledge gained to substantiate the results through experimental testwork on a domestically sourced rare earth ore. This paper will outline the fundamentals and literature of rare earth mineral flotation, review its industrial applications and provide some recent research updates.THE RARE EARTH ELEMENTSRare earth elements (REE’s) are a unique family of elements with nearly identical physical and chemical properties. They account for approximately 1/6th of all naturally occurring elements, but the entire group occupies only one position on the periodic table. These 15 elements make up the lanthanide series (atomic numbers 57–71), and all but one (promethium) occur naturally. In addition to these 15 elements, yttrium and scandium are also considered rare earths since they tend to occur in the same deposits as the rare earths and share similar physical and chemical properties as seen in Figure 1. In particular Figure 2 denotes, a cartoon of the subtle differences in each caused by the 4f atomic sub shell (Gschneidner Jr., 1964). These subtle differences result in very difficult challenges in the selective concentration and final separation of each rare earth. (Anderson, 2015, Kronholm, Anderson, Taylor, 2013)Rare earths are separated into two different subsections; the “lights” or LREE’s (lanthanum57 through europium63) and the “heavies” or HREE’s (gadolinium64 through lutetium71). Yttrium is generally considered a heavy rare earth since its ionic radius is close to that of the HREE’s, while scandium is not considered either a light or a heavy."

Jan 1, 2016

By C. P. Parsons

During the past year considerable interest has been shown in cementing operations for shutting off bottom water, whipstocking, etc. A number of plug-back methods have been used, with various adaptations for special conditions, but those described in this paper are representative of the methods now in use. Conditioning the Well Various preliminary operations for improving the results from plug-back operations have been evolved. In one method, a nitroglycerin shot is discharged at the upper portion of the formation to be plugged off, the purpose being to make a wide place in the hole in order to give the cement a more secure anchor against thrust pressure of the water against the bottom of the cement plug after the well is again put on production. Another is intended to attain a similar result by under-reaming a wide place in the hole by means of a rotary wall scraper. In one well in which this device was used there was a water sand at the bottom of the well immediately below the cap rock above which the oil sand occurred. Before the plugging back operation, the water sand was underreamed in an attempt to get a square shoulder on the underside of the cap rock, in order to prevent the water from breaking in over the top of the cement plug after the well should be put on production, and also to get a more secure anchor for the cement plug against the thrust pressure of the water against it. As an aid in calculating the amount of cement required to fill a given amount of hole to be plugged back, a device has been developed for measuring and recording the irregularities and cavities in open holes, called an "open-hole recording caliper." If consists of a steel shell, 5 in. in diameter, which encloses a recording mechanism that receives impressions from four movable arms that make sliding contact with the wall of the hole. The arms operate a ratchet, which raises and lowers a recording stylus against a chart. Each arm registers its own radius. The device is run into a well on a steel measuring line. While the device is being lowered, the arms are folded inside the shell; they are

Jan 1, 1936

By T. S. Lovering

An economic geologist is concerned primarily with finding deposits of economic value, estimating their tenor and quantity, their shape and position. Thus the primary problems can largely be lumped under three headings: position, character and quantity; and all three are phases of the broader problem of genesis. Distribution, tenor and quantity are of immediate practical importance and are studied constantly by all who exploit mineral deposits. Although the emphasis changes from year to year, the problems of genesis seem more remote and rarely get the serious consideration from the field man that the other three do. Our understanding of the problems of the genesis of mineral deposits has come largely as a by-product of more evidently utilitarian work in the past, and probably will continue to grow in the same manner lor many years to come. However, it might be economically fruitful for the producers to have many competent investigators spending their time chiefly on the problems of genesis of mineral deposits. Many years ago, when first engaged in work for the United States Geological Survey in Colorado, I expressed a conviction which was just then dawning on me by saying that economic geology was turning out to be 80 per cent structural geology, to which Mr. B. S. Butler replied, "Yes, and more than 80 per cent of structural geology is lithology." At the present time there seems to be a widespread feeling among economic geologists that the problems of position or distribution are largely problems of structure and rock types. Types of Research Ptesearch in any branch of geology can be conveniently divided into two types: field research and laboratory research. Ideas are usually dug up in the field, pruned or developed in the laboratory, and taken back to the field for proving. For either the first or last step the field data should he as complete as possible, and the structural geology of nearly all our mineral deposits still needs more detailed delineation. In general, this means mapping on larger seales. Ideally the structural map should give a factual picture of a11 visible effects of stress; there is still room for vast improvement in the technique of presentation. Information that is much

Jan 1, 1940

By [Dipl. -Ing. ] Karl Angerer

The "New Austrian Tunneling Method" is one of the most significant developments in European tunneling in the last 15 years. I hope this report will show the significance of this tunneling method, which was developed in Austria exactly 18 years ago and which is now used in many European countries. In Austria from 1948 to 1953, the Moll tunnel with a length of 11.6 km (about 7.3 miles) was constructed as a part of the Kaprun power plant. Depth of overburden varied from 1000 to 1400 m, and there were many rock bursts in calcareous-schist formations. Here for the first time it was found that a thin concrete lining would help to prevent rock bursts if it was sprayed on the rock soon after blasting. During construction of the Prutz-Imst tunnel in Austria from 1953 to 1956, the shotcrete lining was sprayed on the phyllite surface a certain distance behind the blasting face to prevent rapid rock decomposition. This method was also tried in soft-rock sections of the tunnel where steel and wood supports usually were necessary. To prevent loosening of the rock, application of the sprayed concrete was tried immediately after blasting. This method made it possible to tunnel through very soft ground. Where necessary, the shotcrete was supplemented by steel arches and mesh reinforcement. At that time (1953-1956), the machines and equipment for guniting or spraying concrete were being improved rapidly and it became possible to spray aggregates up to 25 mm in diam. Hardening accelerators brought quicker strength and better adhesion of the shotcrete-this also made it possible to use the method in wet tunnels. If the tunnels are extremely wet or flowing with water, it is necessary to seal off the wet rock or drain the water, using, for instance, the Oberhasli method. After these first successful steps with the new Austrian method, large portions of the Schwarzach power plant in Austria were designed and built. At this operation, shotcrete was used almost exclusively for tunneling work. It was on this site where, for the first time, a tunnel 120 m long with a 45-sq- m section was driven through overburden without one piece of timber

Jan 1, 1970

By T. S. Lovering

An economic geologist is concerned primarily with finding deposits of economic value, estimating their tenor and quantity, their shape and position. Thus the primary problems can largely be lumped under three headings: position, character and quantity; and all three are phases of the broader problem of genesis. Distribution, tenor and quantity are of immediate practical importance and are studied constantly by all who exploit mineral deposits. Although the emphasis changes from year to year, the problems of genesis seem more remote and rarely get the serious consideration from the field man that the other three do. Our understanding of the problems of the genesis of mineral deposits has come largely as a by-product of more evidently utilitarian work in the past, and probably will continue to grow in the same manner lor many years to come. However, it might be economically fruitful for the producers to have many competent investigators spending their time chiefly on the problems of genesis of mineral deposits. Many years ago, when first engaged in work for the United States Geological Survey in Colorado, I expressed a conviction which was just then dawning on me by saying that economic geology was turning out to be 80 per cent structural geology, to which Mr. B. S. Butler replied, "Yes, and more than 80 per cent of structural geology is lithology." At the present time there seems to be a widespread feeling among economic geologists that the problems of position or distribution are largely problems of structure and rock types. Types of Research Ptesearch in any branch of geology can be conveniently divided into two types: field research and laboratory research. Ideas are usually dug up in the field, pruned or developed in the laboratory, and taken back to the field for proving. For either the first or last step the field data should he as complete as possible, and the structural geology of nearly all our mineral deposits still needs more detailed delineation. In general, this means mapping on larger seales. Ideally the structural map should give a factual picture of a11 visible effects of stress; there is still room for vast improvement in the technique of presentation. Information that is much

Jan 1, 1940

By C. P. Parsons

During the past year considerable interest has been shown in cementing operations for shutting off bottom water, whipstocking, etc. A number of plug-back methods have been used, with various adaptations for special conditions, but those described in this paper are representative of the methods now in use. Conditioning the Well Various preliminary operations for improving the results from plug-back operations have been evolved. In one method, a nitroglycerin shot is discharged at the upper portion of the formation to be plugged off, the purpose being to make a wide place in the hole in order to give the cement a more secure anchor against thrust pressure of the water against the bottom of the cement plug after the well is again put on production. Another is intended to attain a similar result by under-reaming a wide place in the hole by means of a rotary wall scraper. In one well in which this device was used there was a water sand at the bottom of the well immediately below the cap rock above which the oil sand occurred. Before the plugging back operation, the water sand was underreamed in an attempt to get a square shoulder on the underside of the cap rock, in order to prevent the water from breaking in over the top of the cement plug after the well should be put on production, and also to get a more secure anchor for the cement plug against the thrust pressure of the water against it. As an aid in calculating the amount of cement required to fill a given amount of hole to be plugged back, a device has been developed for measuring and recording the irregularities and cavities in open holes, called an "open-hole recording caliper." If consists of a steel shell, 5 in. in diameter, which encloses a recording mechanism that receives impressions from four movable arms that make sliding contact with the wall of the hole. The arms operate a ratchet, which raises and lowers a recording stylus against a chart. Each arm registers its own radius. The device is run into a well on a steel measuring line. While the device is being lowered, the arms are folded inside the shell; they are

Jan 1, 1936

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By Adam Pickles, Duncan Nicholson, Richard E. Prust, Hoe C. Yeow

"Moorhouse is founded on what at the time of construction were the deepest base grouted piles ever installed in London, specifically designed to accommodate settlement from the proposed development of Crossrail. This paper describes design and construction issues associated with this project with special emphasis on the construction aspects of installing these piles in a heavily congested site in Central London.INTRODUCTIONConstruction of the deepest base grouted bored piles in a congested site in Central London in 2002 posed a number of design and construction problems. To add to the complication, the new structure's footprint is within the safeguarded zone of the proposed new cross London rail link, Crossrail. Therefore the piles were required to be designed to allow for the effects of construction of the proposed Crossrail's tunnels and a new station at Moorgate. The design and construction issues associated with this project are described in this paper and methods used to address such issues are presented.MOORHOUSE DEVELOPMENTThe new nineteen storey high Moorhouse building was commissioned by Moor House Limited Partnership and will form another new Central London landmark building by the British architect Foster and Partners. Two of the four facades feature complex geometry to fulfill the city's planning requirements. The building is a steel frame structure stabilised by a reinforced concrete core. Floor plates span between the core and the perimeter with two rows of internal columns.The complex geometry of the superstructure requires a diagonal ""bandolier"" to transfer floor loads to certain perimeter columns. Another salient feature of the superstructure is the ribs that are provided to act as sloping columns to carry the loads down to the foundations."

Jan 1, 2005

By Adam Jordens

Along with gravity separation and froth flotation, magnetic separation is one of the most common techniques for separating minerals. Minerals are separated by a magnetic force that is dependent on a combination of the applied magnetic field, the magnetic field gradient and the magnetic properties of the minerals themselves. Minerals may be classified as diamagnetic, paramagnetic or ferromagnetic based on the way they interact in a magnetic field. The magnetic susceptibility of a material may be determined by using a vibrating sample magnetometer to determine the magnetic moment of the material in an applied magnetic field and then converting this measured moment into the material?s magnetic susceptibility. In the case of rare earth minerals, magnetic separation is commonly used to remove ferromagnetic iron-bearing gangue minerals and to concentrate paramagnetic valuable minerals such as monazite and xenotime. These magnetic separation steps are frequently preceded by a gravity separation step as many iron oxides and rare earth minerals have specific gravities that are much larger than those of typical gangue minerals. By varying the magnetic field intensity it may be possible to use magnetic separation to selectively separate the paramagnetic and ferromagnetic minerals that report to the concentrate after gravity separation. Test work on a Canadian rare earth ore has shown that a gravity concentration step using a Knelson concentrator was able to selectively concentrate heavy magnetic minerals as evidenced by increased recoveries, relative to the Knelson tailings and fresh feed, after processing through a wet variable intensity magnetic separator. Mass pull to the Knelson concentrate was 4.5 % and the magnetic recovery of this concentrate, at 0.94 T, was approximately 40 % higher than the magnetic recovery from the Knelson tailings (70 % versus 30 %). The products of the wet high intensity magnetic separation were also analysed using a vibrating sample magnetometer to determine the magnetic susceptibilities of the various concentrate and tailings products.

Aug 1, 2013

THERE are few industrial and metallurgieal processes which do not require the application of heat energy, and the modern demand for increased working efficiency has resulted in attention being paid to temperature control as a means of ensuring fuel economy and more efficient plant operation. In general, mill accuracy required is not very contant in laboratory work, and few industrial operations are controlled to within less than 5° while in many cases greater limits are allowable. Almost every thermal property of matter has been suggested as a basis for the construction of pyrometers, but the thermo-electric type finds by far the widest application, and hence this paper will deal only with the principles, construction, and uses of this type of instrument. THERMOELECTRIC PYROMETRY.In the year 1821 Seebeek discovered that if the ends of two dissimilar metal wires were joined and one junction heated, a current flowed in the circuit, and the KMF (electro-motion force) set up could be measured by inserting a galvanometer at the cold junction. The phenomenon was not thoroughly investigated for many years, but, as the demand for high-temperature thermometers increased, several investigators, of whom Le Chatelier was one of the pioneers, successfully endeavoured to utilize the principle in pnometric construction. The couples which gave the most satisfactory results were discovered, improvements were made in material and design and the present-day type of instrument gradually evolved. The apparatus consists of three main parts, viz. (1) The thermo-couple itself of two dissimilar metal or alloy wires together at one end. (2) The leads which connect the terminal of the thermo-couple with the measuring instrument.

Jan 1, 1923

By T. T. Ni

FOR MORE THAN 200 years, the Kochiu district of Yunnan province has been, and it still is, the hub of China's tin industry. The district produces annually from 80 to 90 per cent of that country's out-put of tin, which averages about 9,300 tons a year and places China fifth among the tin producing nations of the world. The tin ore reserves of the country are estimated (1) at 1,873,370 metric tons, of which 1,500,000 tons are in the Kochiu district. The mill of the Yunnan Consolidated Tin Corporation, described in this paper, is the only one of its kind in China. MINING AND SMELTING There are only two tin mines in the Kochiu district operating with modern equipment -the Hsin-Chang and the Lao-Chang, both owned by the Yunnan Consolidated Tin Corporation, a government company. The Hsin-Chang mine has four working levels with cross-cuts 6 ft. by 6 ft. and is equipped with steel mine cars and trucks to haul the ore. The ore is hoisted to surface in a three-compartment shaft and transferred to the mill by a 4-kilometer aerial tram. The Lao-Chang mine has two circular shafts 656 feet apart, each equipped with two cages. Haulage-ways 1,600 meters and 1,000 meters long, respectively, have been driven to the southwest from these shafts and are connected by three cross-cuts.

Jan 1, 1951

By Ikuhiro Sumi

A new steelmaking process, in which manganese ore was intentionally reduced, was developed to achieve a higher manganese Yield using a combined blowing converter. In this study, manganese behavior was discussed through the introduction of a model. Apparent reduction rates of manganese were calculated by the two terms that were determined experimentally, with SOkg and 2S0ton combined blowing converters. The model calculated manganese changes during the operation. We applied the model to the actual operation and found that manganese behavior was predicted fairly well by this model.

Jan 1, 1996

By V. A. Ivanova, T. N. Perunkova, N. O. Dorozhanova, G. V. Mitrofanova

"Oxyethylated compounds are used as reagents-regulators in the flotation of non-sulfide ores, in particular, apatite-containing ores. Thus, the necessary degree of selectivity in the flotation separation of two calcium-containing minerals of apatite and calcite is achieved only by using, in addition to a collector, regulators-reagents from the nonylphenol ethoxylates class. In order to establish the most optimal structures, this paper presents a comparative assessment of the physical-chemical and flotation properties of several classes of oxyethylated compounds - alkylphenol ethoxylates, aliphatic alcohol ethoxylates and oxyethylated carboxylic acid. The authors have studied their dispergating ability with respect to the air phase and calcium soaps of the carboxylic collector. Dependences of foaming properties of regulators on the degree of oxyethylation have been determined. Adsorption isotherms of sodium oleate on apatite and calcite in the presence of regulators have been obtained. It has been shown that the presence of oxyethylated compounds in the solution reduces the amount of the adsorbed fatty acid collector. The influence of the considered classes of regulators on apatite flotation has been studied. The interrelation of flotation properties of oxyethylated compounds and their molecular structure has been established.INTRODUCTION Flotation plays a leading role in complex apatite-containing ores processing. However, two calcium-containing minerals - apatite and calcite, which compose apatite-carbonate ores, are characterized by close flotation properties. Selective separation of these minerals is a difficult task, the solution of which is impossible without using reagents-regulators. One of the ways to ensure the selectivity of the flotation separation of calcium-containing minerals is the use of reagents-depressants such as sodium silicate, starch, cellulose derivatives, and others (Liu et al., 2016; Rao et al., 1989). Another method is the application of nonionic reagent regulators (Filippov et al., 2016; Filippova et al., 2014; Ignatkina, 2017), which contribute to the adsorption of the ion collector (Filippov and Filipova, 2006 Rao and Forssberg, 1997) and stability of formed froth (Sis and Chander, 2003)."

Jan 1, 2018

By Bin Zhu, Mingmei Zhu, Hong Zhou, Xiaofei Dou, Bin Xie, Yu Wang, Tiancheng Lin

In this study, the formation of 2CaO·SiO2 and 3CaO·P2O5 solid solution (nC2S-C3P) in hot metal dephosphorization process is discussed. The variations of CaO and SiO2 mass, both in nC2S-C3P solid solution phase and liquid slag phase with increasing P2O5 mass in CaO-SiO2-FetO-P2O5 slags were calculated using Factsage software. CaO-SiO2-FeOt-P2O5 slag containing up to 18 % P2O5 was melted at 1823 K then cooled to 1673 K. The contents of CaO and SiO2 both in the solid solution phase and liquid slag phase of quenched samples were observed and analyzed by SEM/EDS. Both the calculated and experimental results show that the contents of CaO and SiO2 in the solid solution phase decreased, just opposite in the liquid slag phase, with increasing P2O5 content in the slags. Formation mechanism of nC2S-C3P solid solution in the slags was derived based on the ionic structure theory of molten slag. The SiO4 4- in the nC2S-C3P solid solution can be replaced by PO4 3- in the liquid phase resulting in the increasing of free Ca2+ and SiO4 4- in liquid phase.

Jan 1, 2015

By F. Ajersch, M. Rigaud, M. Jallouli

"Le gonflement des boulettes d'hématite à été étudié à l'aide d'une méthode de mesure standard ISO ainsi qu'à l'aide d 'une méthode de mesure dilatométrique.La première méthode a servi à l'étude des boulettes haute silice (5% SiO2) dont l'indice de basicité (IB = CaO + MgO -i- SiO2 + Al2O3) a été ajustée soit à l'aide d'une addition de dolomie, soit à l'aide d'une addition de pierre à chaux, soit à l'aide d'une addition de ces deux composes. L'indice de basicité variait de 0.05 à 0.12. Les résultats de gonfle ment obtenus à 1000?C dans une atmosphère de 40 CO - 60 N2 ont permis de montrer qu’indépendamment de l'indice de basicité c'est la dolomie qui contribue le plus à diminuer le gonflement par rapport à la pierre à chaux. L'utilisation de l'indice de basicité comme critère de sélection des boulettes est discutée.La méthode dilatométrique a servi à l'étude du gonfle ment de deux types de boulettes préparées à partir de deux concentrés de fer et dont la teneur en silice a été fixée à 2.5% et 0 5%. Ces deux types de boulettes ont reçues les mêmes additions de liant en quantité et en nature. La détermination en continue du gonflement, à 950?C dans 40 CO - 60 N2, a permis d'une part de mieux cerner le niveau de réduction auquel correspond le maximum de gonflement et d'autre part de montrer que l’allure des courbes de gonflement est étroitement liée à la nature du liant. Une augmentation de la teneur en silice des concentres contribue à diminuer le gonflement des boulettes.Des essais de réduction de gonflement non isothermes ont été réalisés à des montées de température à 10 et 20?C/min. Les résultats indiquent que le gonflement déterminé dans les conditions non iso thermes est inferieur à celui obtenu lors des essais isothermes. On discute alors de la validité des essais standards de gonflement qui sont utilisés pour prédire le comportement des boulettes lors de leur réduction dans un haut fourneau."

Jan 1, 1983

By P J. Harris, C T. OÆConnor

Collectors are used to impart hydrophobicity on particles thus increasing their chances of reporting to the froth phase. Also, the extent to which naturally hydrophobic gangue particles, such as talcaceous minerals, report to the froth can be reduced by the use of depressants. Thus the use of collectors and depressants will directly influence the extent to which hydrophobic particles report to the froth. However these hydrophobic particles will also have a direct effect on the characteristics of the froth phase, more strongly hydrophobic particles causing a reduction in the stability of the froth with the expected concomitant effects on grade and recovery. This study included microflotation (ie frothless flotation) and batch flotation of various ores using a number of different collectors and depressants and a newly developed froth imaging device (SmartfrothTM). Flotation performance was characterised by mass and water recovery, and recoveries and grades of the valuables. This paper shows how the various reagents influenced the behaviour of the pulp and froth phases. The critical importance of managing the type and dosage of reagents used in flotation with a view to optimising their influence on the froth phase is discussed.

Jan 1, 2005

By J. G. Peacey, G. Csicsovszki

The target of this study was to clarify the role of lead on the dissolution of gold in the (NH4)2S2O3-Cu leaching system via chronopotentiometry, linear sweep voltammetry and chronoamperometry. It was found that the dissolution of gold was significantly increased with lead concentration up to 10 mg/1 Pb in the system of 0.1 M (NH4)2S2O3 and 50 mg/1 Cu. \/oltammograms suggested that the anodic dissolution of gold was virtually independent of lead concentration in the range of 1-10 mg/1 in 0.1 M (NH4)2S2O3 solution while in solutions containing copper as well, addition of lead increased the anodic dissolution of gold.

Jan 1, 2011

By Russell G. Warncke

"This report is based primarily on a study of safety conditions and practices followed in the coal mines of Japan. Not all of the coal fields in Japan were studied, but typical mines in the largest producing areas and a fair cross section of coal-mine-safety conditions observed during February to April 1948 are described.Information was obtained through investigations conducted in the mines, discussions with mine-management officials and representatives of labor unions of the various mines visited, and examination of records and statistics from the various offices of the Coal Board of the Ministry of Commerce and Industry and from the Coal Association of Japan. Statistical data covering the same subject, obtained from different sources, varied in many respects and apparently were reported inaccurately, but such discrepancies can be attributed to different methods of reporting and compiling statistics.It is difficult to correlate the high fatal and nonfatal injury rates that prevail in Japanese coal mines with the conditions observed in the mines. Virtually all mines visited were attempting to prevent accidents and explosions, by apparently following known safety precautions for the prevention thereof. Some commendable safety innovations were observed at several mines; they indicated that mine officials are giving thought and consideration to hazardous conditions that affect their particular mines.Naturally, the operating officials and management were anxious to impress the writer with their interest in accident prevention and safety. Operating officials were found to be receptive to safety and wore interested in formulating definite safety programs. Some nines had well-planned and well-organized safety programs, which, if put into effect, would contribute greatly toward reduction of accidents.The approach to safety in Japan is quite different from that in the United States, especially the concept of personal responsibility for accidents and the extent to which the individual should be protected against hazards. Management is responsible for providing and maintaining safe working conditions. Collaboration between management and worker, as understood in the United States, does not exist in Japan.Increase in accidents since the cessation of hostilities is the result of unsettled economic conditions in the coal industry, influx of inexperience workers, and breakdown of discipline among the miners, who have been organized into unions. Those unions are greatly influenced by ""leftist"" tendencies.It was observed that the Japanese mine worker is fatalistic by nature and has little, if any, noticable safety consciousness. The most urgent major requirements to reduce accidents in the coal mines are to train the worker in accident prevention and instruct him regarding the inherent hazards of his occupation.Revision of the mining laws would help to reduce accidents if the companies would comply with such laws and provide safer working places and if the workers would cooperate with management and observe and comply with such laws as are enacted for their protection."

Dec 1, 1949

By Jean Cayouette, Paul Blatter, Paul Cousin

"The Laronde mill was commissioned in 1988 and has been treating the Laronde Penna ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually.In 2008, the Goldex plant began trucking high grade (35-45 g/t Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold grade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine.Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa).INTRODUCTIONFollowing the 2000 to 2003 expansions, the Laronde plant evolved into a mature milling complex with developed processing, man power, and water treatment capabilities able to accommodate the complex Laronde ore. The ore requires a series of grinding, copper/lead flotation and separation, zinc flotation, zinc tails precious metals leaching, followed by a counter-current decantation circuit and Merrill Crowe precipitation. A paste backfill and SO2-air cyanide destruction operate intermittently. The tailings area has a dedicated cyanide destruction and metals precipitation plant prior to water recycling to the mill. A biological water treatment plant was put into service in 2004 to address the build-up of thiocyanate in the tailings ponds at Laronde. This was the result of the high sulphide content of the Laronde ore and 90% recirculation of the process water. The plant uses bacteria to oxidize and destroy thiocyanate, and removes phosphate from the water before it is released to the environment."

Jan 1, 2011