Search Documents

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005

By John C. Ryan

The Emeca Pile Splice, an innovative mechanical prestressed concrete pile splice, is the first robotically welded splice to be fabricated in the United States. An analytical and experimental study was conducted to establish the capacity of the standard splice for 12-in. and 14-in. square piles. The study illustrates compliance of the splice with International Building Code (2006) requirements. A case study for a large petroleum tank foundation project in Port Canaveral, FL is presented, demonstrating the efficiency achieved through use of spliced-piles. For the case-study project, single-piece 18-in.-square, 100-ft-long piles were replaced with 12-in.-square, two-piece, spliced piles. As a result, a significant reduction of material, labor, handling, and equipment was documented for the project. Savings realized on the installed pile cost was estimated to be in excess of 30% by the owner.

Jan 1, 2010

By George W. Land

For the year 1985, the U.S. coal industry produced 881 million tons of bituminous coal and lignite. Domestic consumption amounted to 814 million tons. The electric utilities consumed 689 million tons, almost 85 percent of total consumption, over 78 percent of production. In May, 1986, the NCA forecast that with moderate growth rate averaging 1.9% per year from 1985 through the year 2000, production could reach 1,176 billion tons and domestic consumption 1079 billion. The estimate for electric utilities indicate 924 million tons for the year of 2000, about the same percentage of production and consumption as now experienced. Before we consider the main topic of this paper, the cost of using high sulfur coal, let us examine the coal use patterns of the last 25 years, the changes in those patterns and consider the reasons for those changes. Table I shows those changes.

Jan 1, 1986

By Luis Valentim, Terry Cousins

The goal of a mine is to produce ore at the lowest possible cost with due regard to safety of pemonnel and equipment. The mining process consists of a number of discrete operations such as planning, drilling, blasting,excavation, transportation and crushing. These processes are interrelated and cannot be considered as separate activities when optimising output and minimising cost. In order to optimise the global costs it may therefore be necessary to increase cost in one area such as blasting design and management beyond the norm.

Jan 1, 1998

The organisers of this function have suggested that this presentation should accomplish the following broad goals:set the technical tone for the conference to follow, implying some discussion of the æstate-of-the-artÆ of reserve estimation; and raise some current and common problems or deficiencies in our art in order to be thought provoking. As an engineer it is always easier to raise problems than to solve them with state-of-the-art. Consequently, I have had to limit the extensive list of problems that could have been discussed within this presentation. In regard to the state-of-the-art, this presentation will not be an esoteric discussion of the latest statistical estimation processes, although I intend to challenge those with skills in that area to address some of the thought provoking issues later on. The subtitle of the paper was established after reading an excerpt from æLife on the MississippiÆ by the American humorist Mark Twain in which Twain observed that the Mississippi River had become shorter during his working period on the River due to natural cut-offs and man made channels. Projecting into the future, he calculated that by now, Cairo, Missouri and New Orleans, Louisiana would become a single city with one mayor (the two cities are still separated by some 500 air miles). As a moral to this story Mark Twain observed that one can obtain: æwholesale returns of conjecture out of such a trifling investment of factÆ.

Jan 1, 2000

By Dr. Tristan Worsey, Dr. Jhon Silva-Castro

Confinement is an important aspect of blasting. Reducing and increasing confinement can determine whether a blast design performs properly. Over-confined shots usually have poor fragmentation, higher vibrations, and stemming ejection, and unconfined shots usually have a lot of air blast and fly rock. When talking about confinement in blasting, static confinement conditions are typically referenced. Static confinement conditions are ruled by free faces, shot muck, burden, spacing, stemming, hole depth, toe, etc. All these conditions exist in a static state. Static confinement conditions are generally analyzed before the shot takes place, but once the shot starts, the conditions will change according to the sequence and delay of the shot. Once the shot starts, Dynamic confinement takes place. For the authors, Dynamic confinement is the confinement conditions that exist for the charge when it fires and should account not only for the variables included for the static confinement but also for the time and sequence of the shot. The paper explores the theory of dynamic confinement and its role in influencing blast performance. Time and sequence are the main influencers of dynamic confinement and will be the focus of the paper. How to generate the appropriate timing based on blast design, dynamic confinement, static confinement, and geology will also be discussed.

Jan 21, 2025

By S. H. Castro

The El Teniente molybdenite plant (Chile), with a nominal capacity of 3,200 tpd of bulk Cu-Mo concentrate, produced approximately 3,385 metric tonnes of Mo during 1998 by using the phosphate Nokes process (LR-744 reagent). This is the only Chilean moly plant which traditionally has depressed copper and iron sulfides with LR 744 reagent, which is a hydrolysis product of P2S5 and NaOH. El Teniente's ore Mo grade is 0.02%Mo and is concentrated to 0.45%-0.50% Mo in bulk Cu-Mo flotation. Subsequently, molybdenite is floated by selective flotation to depress Cu and Fe sulfides, such as chalcopyrite, bornite, digenite and pyrite, to produce typically a 49%-50%Mo molybdenite concentrate. An optimisation program during the last two years was undertaken to improve molybdenite recoveries. Current molybdenite plant technology at El Teniente and use of phosphate Nokes in the process process is reported. Use of phosphate Nokes reagent has increased average Mo recovery from 70.5% in 1977 to a mean 74.7% for the first 4 months of 1999. The global Mo recovery, including bulk flotation, incresed from 42.3% in 1997 to 46.8% in 1998, with a projection of 55.5% for 1999. Mo production per year has increased from 3,181 tons in 1997 to 3,385 tons in 1998 and a projected 4,000 tons for 1999.

Jan 1, 1999

By Dol Duwez, R. H. Willens

A technique is described by which metastable alloy phases can be obtained by very rapid cooling from the liquid state. The results obtained so far have lead to; 1) extension of solubility limits beyond their equilibrium values, 2) new phases not found under equilibrium conditions, and 3) amorphous alloys. MANY new nonequilibrium phases have been found in alloys rapidly cooled from the liquid state. The technique used in these investigations essentially consisted of propelling a small molten globule of an alloy against the inside surface of a rotating copper cylinder. Since these original experiments were performed, the technique has been greatly improved. The purpose of this paper is to describe in detail, for the first time, a simple and efficient apparatus for producing foils of alloys which are rapidly cooled from the melt and to summarize some of the observations made on these alloys. I) FAST COOLING APPARATUS In the original fast cooling apparatus used by Duwez, Willens, and Klement,' the alloy was melted in a graphite container having the shape shown schematically in Fig. 1. A shock tube was attached to one end of the graphite part to supply the pressure for ejecting the molten globule. The globule was received on the inside of a rotating cylinder located about 0.5 in. from the exit of the graphite container. The globule trajectory made an angle of about 15 to 25 deg with the tangent to the cylinder at the point of

Jan 1, 1963

The basic principles of mineral valuation were recognised and propounded at the beginning of this century and have remained virtually unchanged since then. Valuation is seen as a two part process commencing with a technical examination of the mineral property followed by a manipulation of the results of the technical examination in order to determine the monetary value of the project. A thorough and competent technical examination was seen then and remains now as the essential but not sufficient foundation for reliable valuation. All authors stressed the need to maintain the integrity of the data base and to ensure adequate coverage of all relevant aspects. The monetary valuation process through most of the first half of this century was mainly based on the Hoskold two rate method, derived from the formulae for valuing annuities but modified to provide explicitly for recovery of capital. Though the basic principles of valuation have not changed significantly, the means of implementing the components of the technical examination, the styles of deposits being evaluated and the mechanisms of monetary valuation have changed dramatically. Despite all the technological improvements, however, mineral valuations are still as apt to vary from realised performance as at any time in the past. As well, mineral property valuations are now being extended to cover all assets of potential value, including valuation of exploration tenements with or without identified resources. Valuation of exploration tenements will continue to be one of the most difficult and contentious of valuation tasks.

Jan 1, 1994

By Arthur V. Abbott

During the past four years I have had occasion to make quite extensive use of steel castings in the manufacture of testing-machines and large scales for Messrs. Fairbanks & Co. The failure of some of these' castings at stresses much below those which were claimed for them by the makers, induced me to institute a series of experiments to determine the actual constructive value of the steel castings now to be obtained in this country. The art of steel-casting is rapidly improving, almost every issue of the scientific press bringing accounts of some new development; consequently, the results of the following experiments are only exponents of the value of steel castings as at present made. In order to make the examination as thorough as possible, ten sets of patterns were made and forwarded to as many different firms in the country who advertised to make steel castings. The first part of the accompanying table gives a list of these manufactures, together with the price per pound. The order accompanying the patterns simply requested the manufacturer to supply two castings from each pattern of his ordinary product of steel. These castings were sent to me and paid for in the usual manner, so that it is probable that the samples fairly represent the quality of the average of steel castings, and are free from the suspicion of being "special runs." Two patterns were sent to each maker, one being a straight

Jan 1, 1886

By R. W. Brock

This subject is too broad and comprehensive to be dealt with adequately and authoritatively in this paper. It calls for the knowledge and experience of many men, but the results from such collaborative effort would be of great value, particularly if similar reports of the principal mining districts of the world were made on a standardized basis so that conditions everywhere might be directly and accurately compared. In considering conditions affecting mining in British Columbia, unfavourable as well as favourable factors must be taken into account. The unfavourable are apt to loom large and to be exaggerated rather than minimized; for it is human nature to see the blackness of the cloud rather than the silver lining; to think that one's own undertaking is beset with peculiar difficulties, and to attribute lack of greater success to out-side causes rather than to personal shortcomings. It should be recognized, however, that there is no country where the conditions for mining are ideal. The ideal mining country is the product of imagination, invested with every favourable condition found anywhere, but with none of the unfavourable conditions that are always present in reality. So if British Columbia has some handicaps to the industry, it is in good company. What is important is that the advantages compensate for the disadvantages, that the balance will compare favorably with that of competing states, for mining, like every other industry is competitive, and the cost of one's product must have a definite relationship to its price in the world's market.

Jan 1, 1924

By T. B. Williams

Most geologists have felt the need of a longer base than is ordinarily available when using a Brunton compass or other convenient instrument for taking strikes and dips in the field. To overcome this difficulty a lath or stick with straight parallel sides is frequently used. This accessory adds to the accuracy of the work, but it is a decidedly inconvenient one for the geologist to carry, especially if he be heavily loaded or is travelling on horse-back or through thick brush on foot. The writer has abandoned its use in favour of a sturdy two-foot carpenter's rule. The rule preferred is manufactured by J. Rabone and Sons, Birmingham, England. It is provided with a good level-bubble set in one of the limbs, and a scale, of the protractor type, graduated to five degrees through 180 degrees, attached to the main joint at the middle of the rule. (See Figure 1). For an instrument of its kind it is very accurate, and, in addition to the uses mentioned below, it 'is a handy thing to have around any camp. It is frequently used when plotting roughly in the field and for a protractor when one is not available. When not in use it may readily be carried in the top of the high-boot or legging. Ordinary strikes are measured as illustrated in Figure 1, the compass being held against the rule, which is in a horizontal position. Dips may be measured in a corresponding way by holding the Brunton compass against the extended rule, which is thus used merely as a straight edge. It is usually much more convenient, however, to ? use the rule only for this purpose, in which case one foot of the length rests as a straight-edge against the rock surface. This adaption is shown in Figure 2.

Jan 1, 1929

By E. Ghali, W. Zhang, G. Gabra, N. Sorour, G. Houlachi

The additives polyacrylamide, 1-Butyl-3-methylimidazolium chloride, Tetra-butylammonium bromide, Benzalkonium chloride and chitin are evaluated during zinc electrolysis from synthetic acidic sulphate electrolyte containing Mn2+ ions, in absence and in presence of 0.0055 mg dm-3 of Sb3+ ions. Galvanostatic polarization tests for 2 hours at 50 mA cm-2 and 38oC were carried out to determine the cathodic and anodic potentials, and current efficiency of the deposited zinc. Potentiodynamic polarization and cyclic voltammetry tests have also been employed to study the electrochemical behavior of each additive on the zinc deposit on aluminum electrode. Results showed that, in presence of Sb3+, adding 1 to 3 mg of 1-Butyl-3-methylimidazolium chloride increases the cell voltage by ˜0-7 mV. Current efficiency is increased by ˜4.90-6.40%; power consumption is reduced by ˜147-173 kWh t-1 by adding 1-3 mg, respectively. However, in absence of Sb3+, cell voltage is decreased by ˜7-28 mV, current efficiency is increased by ˜0.70-1.50%; power consumption is reduced by ˜41-47 kWh t-1 by adding 1-3 mg. The effect of the other additives on cell voltage, current efficiency, lead content and morphology of zinc deposit has also been examined. Surface morphology and crystallographic orientation of the deposit was studied using scanning electron microscopic (SEM) and X-ray diffraction (XRD), respectively. The content of lead in the deposit has also been measured using inductively coupled plasma spectroscopy (ICP).

Jan 1, 2015

By T. Fraszczak, U. A. Peuker, T. Mütze, T. Leißner, A. Wikedzi

The present paper highlights on the comminution and liberation properties of two greisen-type lithium bearing-mica ore blends (L1, L2) subjected to different breakage devices; cone crusher (CC), roller crusher (RC), rotor beater mill (RBM) and a screen mill (SM). The particle size distribution (PSD) of the products from each device were evaluated to search for an appropriate PSD model using Gates-Gaudin-Schuhmann (GGS) and Rosin-Rammler (RR) functions. In order to determine an appropriate function that could better describe the PSDs from the devices used, the coefficient of determination (R2) was used as a criterion. In terms of mineral liberation studies, due to costs, only products from rotor beater mill (RBM) were examined through an automated scanning electron microscope (SEM) technique. It was found that RBM, RC and SM products were better described by the RR model than the GGS model with higher R2 values (0.97-1.0). However, cone crusher products for L1 were better described by GSS model, while that for L2 were better described by RR model. In terms of the spread of size distribution as indicated by RR model parameters, RC products were more uniformly distributed compared to products from other devices, for both ore blends. Also the RBM products were more scattered than products from other devices. The results indicate that the composition of individual ore blends affected the comminution products PSDs since different PSD model parameters were obtained for samples comminuted by same devices. The modal mineralogy of the two ore blends indicate both to be rich in quartz, topaz, zinnwaldite and muscovite. Further, the result indicate that, for both ore blends, zinnwaldite phase is more enriched in the fraction < 250 µm. Moreover, better liberation of zinnwaldite is observed for L1 compared to L2. This could be explained by differences of the two ore blends in three aspects; the nature of mineral association, reduction ratio of the fractions analysed and the nature of spread of the size distribution.

Jan 1, 2018

By I. Southern, S. Kelebek

"Smelting furnace bricks contain significant quantity of base metals trapped in refractory material. A series of flotation tests were carried out on samples of old bricks from Sudbury area to examine upgrading behaviour for recycling purposes. Depending on the grind size used nickel recoveries varied from 60 to 90.6% with corresponding grades of 20% and 14.7%Ni. There is a trade-off between nickel and copper. The nickel has responded well to fine grinding, however, the copper recovery suffered from it. Mineralogical characteristics and flotation behaviour of the brick material are discussed in reference to those from the primary ore. INTRODUCTIONMineral processing is well recognized as a mature technology not only for the mining industry, but also for the environmental industry for the purpose of remediation and recycling. Materials available for recycling are usually the products of many years ago. There are multiple stake holders in this area. In general, when the processing results in a product that can be reused or sold, the company carrying out the remediation makes a profit, while the regulators and the public are pleased due to a cleaner environment. From these points of view, there have been many papers published over the years on various mineral processing techniques applied to separation of many different materials including from mining and metallurgical industries (Wilson et al., 1994; Tsunekawa et al., 2005; Saikia et al., 2012).Flotation may be viewed as the backbone of the mining and metallurgical industry since its invention for separation of solids from one another almost a century ago. It is capable of recovering a variety of finely divided different solids following their liberation from each other. Its versatility and highly competitive nature in terms of cost per tonne of material processed, accounts for its occasional uses in the environment engineering area. In the mining industry, flotation is the standard method used for the sulphide ores. It can be applied as a bulk flotation and/or differential flotation. Bulk flotation, which refers to co-flotation of several components from their source, is most suitable for environmental cleanup objectives. Desulphurisation of various plant tailings is a typical example of this (Benzazzoua et al., 2000)."

Jan 1, 2012

By George F. Weaton, Eugene P. Pfleider

13.4-1. History. During the past ten years the mining and production of iron ores has been through a revolution. From 1939 through 1948, which included World War II, 561,000,000 tons of iron ore was mined and shipped from Minnesota&apos;s Mesabi Range to the blast furnaces of the United States for the production of iron and steel products (20, 28, 29). The iron mining industry, anticipating the exhaustion of this highly productive source of raw material, instigated a worldwide search for new sources of iron ores. This search was highly successful, both as to quantity and quality. Venezuela (38), Canada (17, 28, 42), Peru (19, 23, 50, 52, 54, 56) Chile, (1, 66, 75), Brazil, and Liberia were among the countries where enormous deposits of high quality iron ores were discovered. The exploitation of these deposits took away the monopoly held by the Lake Superior region for so many years and created a highly competitive market for high quality natural iron ores. 13.4-2. Exploration and Development Practices. SPECIFIC TO IRON MIN- ING. American industries are motivated to continue exploration because new ore discoveries often lead to an improved competitive position with respect to raw material supply. Exploration techniques have advanced rapidly in recent years, to a degree that potentially important iron ore reserves, stratigically located, may now be detectable by application of a combination of refined and diversified geophysical exploration methods. Since the days of the dip needle, iron ore people have placed greatest reliance on the magnetometer. Its successive stages of development progressed from the balance and the torsion type to the fluxgate, and then to the "sophisticated" magnetometers-conceived and developed in th field of atomic physics. By far the greatest advancement in magnetometer prospecting was made when the self-orienting fluxgate magnetometer took to the air. This was not a new development, but it was a breakthrough in reconnaissance investi-

Jan 1, 1968

By Steve T. Laflin

Since the beginning of the nuclear era, there has never been a commercial solution for the large quantities of depleted uranium hexafluoride generated from uranium enrichment. In the United States alone, there is already in excess of 1.6 billion pounds of DUF6 currently stored. INIS is constructing a commercial uranium processing and fluorine extraction facility. The INIS facility will convert depleted uranium hexafluoride and use it as feed material for the patented Fluorine Extraction Process to produce high purity fluoride gases and anhydrous hydrofluoric acid. The project will provide an environmentally friendly and commercially viable solution for DUF6 tails management.

Aug 1, 2010

By H. W. Hitzrot

THE new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addi-tion of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis-charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure-the new fine-ore bin designed and built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work.

Jan 1, 1939

By Katia Vutova, Vania Vassileva

Investigations and results on the refining of tungsten scrap applying electron beam melting (EBM) in vacuum are presented and discussed. In this work EB melting experiments were performed in single or double-melt operations with different power inputs and refining times for tungsten purification and recovery of multiple metals (including refractory and other metals such as Mo, Nb, Cu, Zn, etc.), which are alloyed elements or impurities with high concentrations in the initial materials. Evaluations for extraction of some valuable metals, generated in the condensate at their removal from the liquid metal during the refining process are provided. Efficient technological regimes for e-beam melting and refining that enable the simultaneous production of pure metal ingots and condensates that can be used directly or can be used for subsequent extraction of expensive and valuable metals are presented.

Jan 1, 2016

By David M. Parkes

Geology is frequently complicated, hence only more regular deposits are mined. Coal is generally thick, often steeply pitching and usually soft or well-cleated. Due to competition from open-pit mines, only two underground mines are operating, McIntyre and B.C. Coal. Several other mines are being planned, the method being evenly divided between hydraulic, longwall, and room and pillar. McIntyre mines in the flat part of their formation (up to 20 degrees) uses continuous miners and shuttle cars in the 3m and 6m seams. This company is considering a retreating longwall face. B.C. Coal operates a hydraulic mine in a 16m thick seam dipping at 10 to 55 degrees with a productivity of about 20 tonnes per manshift.

Jan 1, 1982