Search Documents

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015

By C. R. Kato, G. Proulx

"Within the continuous scenario of reduced aluminium price and plants production costs increase, the energy consumption optimization in the aluminum electrolytic pots continues as the main focus for the producers. Energy consumption was chosen as a key performance indicator to drive the efforts and actions for improvements. Alcoa improved the energy consumption by approximately 3% from 2005 to 2015. This improvement was a result of best practices implementation, new technologies introduction, strategic actions with plant curtailments and management practices. The main objective of this paper is to highlight the importance of the management practices for planning and operational improvements beyond the technology changes. About 10 years ago, Alcoa reorganized its approach to retain knowledge in the Smelters by using a Best Practices format. For each specific subject, a skilled team defined the minimum requirements and the Best Practices for several aspects of operation and maintenance, which affect the environment, safety, cost, customers and performance. These Best Practices were deployed to all Smelters combined with training sessions to process and operation professionals. We will describe how the Best Practices were organized, the deployment strategy used, and the approach to measure the plants’ success. We will describe the management approach that includes Manufacturing Analyses focused on 3-year potential, annual planning, and weekly monitoring of plant stability. A manufacturing analysis is organized at select plants with cross-functional participation of specialists from technical, operational, procurement and finance. The output of a manufacturing analysis includes a roadmap of enablers to improve energy efficiency. A quarterly follow-up of enabler deployment is held with the plant and resources that participated in the analysis. Annually, there is a Planning Process where energy consumption enablers are selected to be implemented during the next 3 years for each plant. A monthly critical analysis is made by the plants with regional best practice support. On a weekly basis, key performance indicators are reviewed with determination of a stability index for each plant. Any deviation signal of unstable condition is alerted and supporting resources are diverted to the plant to reverse trend with countermeasures.INTRODUCTIONDue to factors like excess aluminum in the market and lower consumption in China, the LME price is declining along the last years, as showed in Figure 1. In 2011, the price peaked at US$ 2,400/ton and since then, continues to trend down and approaching the lowest level at US$ 1,500/ton in the last 5 years."

Jan 1, 2016

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed. The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grad~, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the fmal cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure 1."

Jan 1, 2003

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

By F. R. Erick Mulder

"AbstractTwo bottom-hole samples have been taken from two new completions in the Turner Valley field, Royalite Lowery No. 8 on the west flank and Royalite No. 73, which was deepened into a lower fault block, on the northeast flank. From the bottom-hole oil of Royalite Lowary No. 8 a synthetic sample was prepared to simulate the original fluid in the reservoir, saturated at the gas-oil contact conditions. The sample from Royalite Lewery No. 8 has been shown to be the original fluid present at this well and represents the oil phase near the oil-water contact in• the reservoir. Complete chemical analysis, P.V.T., and viscosity data have been obtained on these reservoir fluids, which represent the range of saturation from the gas-oil to the oil-water contact in the Turner Valley oil structures. Sampling techniques and the application of the analytical data to reservoir conditions and field operations are discussed. Super-compressibility curves for an average separator tail gas have also been prepared. These data have not been available before. They will be of fundamental value in futu.re reservoir engineering studies of this field and will also serve as a guide in determining operating practices."

Jan 1, 1950

By T. L. Joseph

The size and accessibility of the Minnesota manganiferous iron ore deposits make them attractive as a potential source of ferromanganese, which is essential in the production of steel. For several years the Bureau of Mines has been conducting experiments to determine the feasibility of producing ferromanganese from these ores by a three-step process which involves (1) the smelting of the ores in the blast furnace to produce a high-phosphorus spiegel; (2) the treatment of the spiegel produced from step 1 in an electric or open-hearth furnace to separate the manganese from the phosphorus and the iron; and 3) the smelting of the high-manganese slag from step 2 to produce ferromanganese. The details of the first two steps of the process and the results of tests with the experimental furnaces have been given in previous reports.

Jan 1, 1931

By C van Wyk, I Reeves, J Webber, G B. Gnoinski

The minerals industry has been given an opportunity to grow and continue to advance again in an environment where there is the potential to reap big rewards for efficiency improvements due to buoyant metal prices and the growing demand of markets in Asia. Improving efficiency may also provide a better return compared to risks of expansions and bringing new projects online due to limited human and financial capital.An opportunity for improvement presents itself in the area of mine-mill reconciliation, which entails the quantification of the variance between measurement points along the mining value chain. Reconciliation factors are calculated from the variance between respective sections within the mining sequence. These factors are commonly used as key performance indicators to provide a check on the performance of the operations. Over parts of the mining value chain, there is a fair understanding of the reconciliation between the Resource and Reserve estimates and the measured metallurgical plant inputs and product outputs through understanding of the mine-mill interface. The quality of reconciliation data gathered across the mine and plant is generally not well established due to practices employed in generating the data. The reconciliation variances are often a function of data accuracy and quality used in the comparison. In general, the sources and magnitude of measurement and sampling errors and their impact on reconciliation are not that well understood. Examples of the current practices of mass measurement, sampling, sample preparation, chemical analysis and quality assurance for broken ore and across the metallurgical process stream are considered. Guidelines are given for those reconciliation elements that are identified as requiring a high degree of confidence for Mineral Resource/Reserve and metal accounting reporting. These guidelines are presented and practices are demonstrated to improve mine to mill reconciliation and support increased resource to product efficiency and value.CITATION:Gnoinski, G B, van Wyk, C, Webber, J and Reeves, I, 2012. Guidelines and practical applications for continuous improvement in mine to mill reconciliation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 309-316 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Artemio Miranda

El presente texto señala el problema de la silicosis entre los trabajadores mineros peruanos. Dicha enfermedad se desarrolla por la inhalación del sílice libre que una vez adquirida, conduce al enfermo a la incapacidad parrcial o total para todo trabajo que demande esfuerzo físico, dejando a muchos de ellos en la condición de inválidos. Algunas de las lesiones anatómicas no evidencias síntomas y solo puede ser visualizado a través de una radiografía. Asmismo, la clasificación de la silicosis se desarrolla en tres estadios, basados en la evolución de las lesiones anatómicas detectables radiográficamente.

May 1, 1952

By Charles Stahl

El presente texto describe la comercialización de la plata a corto y mediano plazo. El periodo de corto plazo se refiere a cualquier negociación dentro de un período de 5 minutos y tres semanas, mientras que la de mediano plazo, es la transacción que se produce entre dos y tres meses. Para la comercialización de metales es necesario la confianza y la paciencia como habildidad para el éxito de la negociacion, de forma que se tiene que comerciar con un equilbrio y sin excesos.

Jan 1, 1984

By Takao Yasugi

The majority of copper in the raw material migrates to the de-copperized dross that forms when the crude lead produced in the blast furnace is treated in the de-copperizing process. The de-copperized dross is treated in the electric furnace producing matte, speiss, and crude lead. The de-copperized dross also contains the silver. Therefore, it is important to improve the rate of silver migration to the crude lead. For this reason, the behavior of silver between the matte, speiss and crude lead phases was examined. At the same time, several tests to improve the percentage of silver migrating to crude lead were conducted.

Jan 1, 2003

By George E. Fasching

The Bureau of Mines has developed a pulse counting system with improved energy resolution and having dual channels to process pulses at different rates and a pulse pileup detector for channel selection. Pulse input is delayed until the detector determines if any pulse is so closely followed by a second pulse as to constitute pulse pileup. If no pulse pileup is detected, the slower channel is selected; this clips the pulse to a wide pulse width to retain good energy resolution. If pulse pileup is predicted, the fast channel, with correspondingly shorter pulse width, is selected to improve resolution with respect to time. Output of the two channels is transmitted to a pulse height analyzer for interpretation. The pulse processing system can process count rates above 300,000 counts per second with little loss in energy resolution.

Jan 1, 1974

By A. A. Sizikov, V. A. Sizikova

Key parameters to consider for any producer: bring down production cost and lead time; Lean production as a tool to achieve maximum efficiency; How to implement lean principles: discontinuous vs. continuous production (aluminum industry); About RUSAL: global top-three aluminum producer; Lean tools at use at RUSAL's production facilities; Pull system, Standardization of work, Just in time, Continuous improvement, Customer-Supplier relations, etc.

Jan 1, 2006

By J. Danoczi

South Africa is running out of fresh water and is looking at ways to improve water usage. This report addresses how a diamond mine in Gauteng has improved the utilization of its water resources. In the past, water from the local river was deemed the most suitable to use in the grease recovery plant but subsequent tests on the water from the slimes dam have shows that this water source is in fact more suitable for diamond recovery. Utilizing the slimes dam water provides a more stable water source than the local river while also reducing the impact of the mine on the water resources in the area.

Jan 1, 2008

By Mogi G, Akaike A, Yamaguchi U

A new algorithm has been investigated for three-dimensional open pit designs to improve the dynamic cone approach which utilises the dynamic programming technique. The conventional dynamic cone method was improved by introducing examination processes: 1. whether any negative blocks are included in a unit cone or not; and 2. whether it is possible or not to leave the negative blocks unmined in the unit cone without disturbing the geometric condition imposed on the slope angle of the cone. The newly developed algorithm was applied to a large-scale open pit copper mine in a planning stage and the results have been compared with those obtained by the conventional methods.

Jan 1, 1995

By Robert H. Poppe

The Regional Copper-Nickel Study examined the potential impacts of copper-nickel sulfide mining, concentrating and smelting operations in northeastern Minnesota and gathered extensive monitoring data on the ecological characteristics of the region's aquatic and terrestrial biota. Because of the many development options possible, the diversity of the region's ecology, and the uncertainty of future environmental regulatory requirements, the Study did not attempt to measure the magnitude of environmental impacts on specific biological communities from a specific development proposal. The Study provides a broad base of environmental resource and impact information that hopefully will assist mining developers and environmental regulators when assessing specific proposals in the future. The following discussion is not a description of what will happen if copper-nickel development occurs in northeastern Minnesota but an exploration of why certain potential aspects of such development should be carefully considered and adequately understood before unnecessary or irreversible decisions are made.

Jan 1, 1980

By H. C. Carpenter

Lignite tar made by low-temperature Lurgi-Spülgas carbonization of North Dakota lignite was hydrocracked in single-pass, fixed-bed operation at 3,000 pounds per square inch over cobalt molybdate catalyst to produce gasoline, and at the same pressure, over zinc chromite catalyst to crack the high-boiling phenolic compounds to low-boiling phenolics. Hydrocracking the raw tar or the creosote-oil fraction from the tar over cobalt molybdate removed most of the oxygen, sulfur, and nitrogen in the forms of water, hydrogen sulfide, and ammonia, and produced gasoline yields from 31 to 59 volume-percent. The gasoline fractions contained from 0.1 to 7.7 volume-percent tar acids, but tar-base percentages were too low for reliable measurement; removal of these materials with dilute caustic and acid solutions also reduced the sulfur and nitrogen to 0.01 weight-percent or less.

Jan 1, 1963

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Condition-based maintenance (CBM) of industrial equipment is generally recognized as being the most cost-effective means for improving equipment availability. However, prerequisite to successful implementation of CBM is a reliable detector of failing components. One such detector, termed the effective negative-sequence impedance, had previously been identified as an indicator of induction motor stator winding degradation. However, a limitation of this detector is that it does not change in a predicable manner under certain motor operating conditions. This paper presents an experimental investigation of an improved technique for on-line detection of induction motor stator winding degradation. The paper begins with a brief description of the detectors, followed by a detailed description of the experimental setup, the experiments conducted, and results.

By Dorricott M. G

Rock bolt installation is generally carried out in two steps. First the hole is drilled and the drill steel is extracted, then the bolt is inserted into the hole and tightened or grouted. With single pass bolting (SPB), however, these two steps can be carried out at the same time. This kind of bolting system has at least three advantages, (1) the time used for the bolt installation could be reduced, (2) the condition of safety for the operators could be improved, and (3) the degree of automation of the rock bolting practice could be increased. The study presented in this paper is concerned with the development of the SPB system. The current state of the system is discussed, and further improvement of the technique is explored.

Jan 1, 1992

By J. Davitt McAteer

Improvements in the control of coal mine dust have occurred over the past 25 years. Simultaneously, dramatic improvements in coal mine production technology have occurred, particularly at mines where longwall systems are in use. Production rates of longwall systems have quadrupled since 1978, and dust generation on these systems has significantly increased. However, technology to address control of the resulting increased levels of respirable dust has not kept pace, and many high-production longwall sections continue to experience problems with respirable dust control. This paper seeks to enlist the entire mining community in the effort to resolve the health problems presented by excessive levels of respirable coal mine dust, particularly on longwall systems. These systems are expected to increase in number and length, and to generate increasingly higher levels of dust as production rates of these systems continue to rise.

Jan 1, 1995