Search Documents

By Akio Ohta

The Hyuga smelter has been producing ferronickel by a rotary kiln-electric furnace process in Miyazaki, Japan. Several approaches to improve our operation have decreased the electrical energy consumption. A new process was developed to decrease the cost of energy even further. Oil and technical oxygen are injected through lances to heat up the calcined ores (calcine) instead of the electric power. Main problems during the development of the process were the short life of the water-cooled lances, the check on security of the safety system and the eruption of combustion gases through the calcine bed. These problems have now been overcome successfully, and stable operation can be maintained. The addition of 1 Litre of heavy oil per tonne of ore can save the electrical energy requirement by 8.6 kwh per tonne of ore. The new process has resulted in a reduction of the electrical energy consumption by more than 10 percent

Jan 1, 1992

By B. Tonn, F. Kröger

"The continued development in engine technology is leading to an augmentation in power density which steadily elevates the requirements for thermally and thermo-mechanically highly loaded components such as cylinder heads and pistons. Due to these high performance requirements conventionally applied Al-Si alloys have reached their application limits, since their mechanical properties deteriorate quickly under the influence of heat. Improved applicability is given by Al-Cu-based casting alloys which have a superior high-temperature strength than Al-Si alloys. Since Al-Cu alloys exhibit insufficient casting characteristics, especially regarding hot tearing susceptibility and increased tendency for porosity, it is currently not possible to cast geometrically complex components in robust permanent mold casting processes. The further development of Al-Cu alloys is aimed at finding an optimum between improved castability while high-temperature strength and thermal conductivity are not deteriorated. It is known that a high amount of eutectic reduces the hot tearing susceptibility of an alloy, but it reduces thermal conductivity at the same time. In this paper it will be presented how the conflicting objectives – improved high-temperature strength, good thermal conductivity and reduced hot tearing susceptibility – can be brought together to develop an optimized Al-Cu alloy for application in permanent mold casting.INTRODUCTION At the beginning of the 21st century car, engine blocks were primarily made of gray cast iron (GJL). Less than half a decade later, the choice of material had shifted towards lightweight materials. Ever since, the car engine manufacturing is dominated by aluminum-based alloys. The weight of car engine blocks could thus be reduced by around 50% due to the lower specific weight of aluminum alloys compared to gray cast iron. Furthermore, the high thermal conductivity of aluminum alloys allowed a reduction of complex cooling channel systems and thereby promoted the advancement of this material group. The further development in engine technology leads to an augmentation in power density which elevates the requirements for thermally and thermo-mechanically highly loaded components. For example, in diesel-powered car engines the upper required limits can reach an ignition pressure as high as 230 bar and gas temperatures of up to 1000°C. Thereby, thermal loads can cause high alternating thermal stresses (Grzincic, 2003) which can effectively be reduced by providing high thermal conductivity."

Jan 1, 2017

By Timothy W. Ellis, John A. Howes

The production of lead-acid batteries is defined by a closed-loop product life-cycle. Active material and grid alloys converge on an adaptable specification that improves both performance and recyclability. This mapping of product requirements for lead-acid batteries has taken over 80 years to develop. But, as the use of batteries made with other chemistries continues to grow, the need for a comparable life-cycle management process becomes increasingly apparent given societal needs to manage raw materials, e.g. the European Union Battery Directive recycling targets. What has taken more than 80 years for lead-acid to evolve in a closed-loop paradigm must now be accomplished in less time for batteries using other chemistries and technologies. End-of-life costs are embedded in the product cost of lead-acid batteries. However, end-of-life costs are not reflected in the product cost of batteries made with other chemistries. Those costs are borne by other constituencies with often inefficient and environmentally damaging results. Lead-acid is a materials technology management model for other products.

Mar 1, 2017

By A L. de Ambrosis, F M. Weir, M Fowler

Traditional kinematic and statistical analyses of geological structure for geotechnical engineering applications, while considered industry standard practice, have some limitations and unrealistic assumptions. An improved approach involves a discrete fracture network (DFN), a numerical model that explicitly represents how defects may be spatially distributed through the rock mass. The DFN technique utilises the structural data in stochastic analyses to give a range of possible models used for visualisation and stability analyses.The early development of the DFN approach was largely associated with modelling fractured hydrocarbon reservoirs and nuclear waste isolation programs. With recent improvements to computational power it has become recognised internationally as a valuable tool for modelling some geomechanical problems encountered when designing excavations in fractured rock masses. For tunnelling or slope stability projects DFN modelling provides visualisation of a rock mass and identification of likely failure mechanisms.This paper presents a suite of DFN modelling undertaken for the design of a tunnel within the Ashfield Shale unit of the Sydney Basin, Australia. The necessary input parameters and derivation of these, along with the importance of both an accurate engineering geology model and validation of the synthetic fracture network are demonstrated. Multiple realisations of the DFN were analysed to provide an indication of the number and volume of unstable blocks for the proposed tunnel geometry, enhancing support design. One fracture network realisation was sliced along multiple sections for use in finite element modelling.CITATION:Weir, F M, de Ambrosis, A L and Fowler, M, 2014. Discrete fracture network modelling for tunnel design in the Sydney Basin, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

An accelerated and coordinated program of coal research is believed by many to be a necessary step in assuring coal's proper position in the expanding energy market. The President's Advisory Committee on Energy Supplies and Resources Policy, for example, made the following recommendation: We recognize that coal is a great national asset and endorse a cooperative study to determine what research and development could be undertaken. The coal industry and both Federal and State Governments should participate in this study and its costs. Representatives of the coal industry have agreed that such a study should be initiated. Accordingly, Felix E. Wormser, Assistant Secretary - Mineral Resources, United States Department of the Interior, requested the Bureau of Mines and Bituminous Coal Research, Inc., to conduct a survey of current research on bituminous coal. In addition to this survey, studies were made to determine research projects that would be of value to the coal industry.

Jan 1, 1956

By Yasumasa Hattori

An extensive study including fluid dynamic calculations, cold model tests, pilot plant tests as well as measurements in a commercial flash furnace was carried out in order to develop a new Sumitomo flash smelting concentrate burner. The pressure measurements in the commercial burner indicated that the premixing of the concentrate and reaction air in a burner was insufficient. Pilot plant tests showed that enhancement of the premixing of the concentrate and reaction air is very effective for improving the burner performance. Using the additional pressure drop of the reaction air as an indicator of the premixing, a new type Sumitomo premixed concentrate burner was developed.

Jan 1, 2003

By Joe Atalla, Jesse Desrochers, Rodrigo Hayashida, Joseph Mukendi Kabuya

The Mont-Wright mine stands as a prominent open-pit operation in Canada, renowned for its vast iron-ore reserves. However, the efficacy of its blasting operations, crucial for efficient production, has encountered challenges due to the diverse lithological compositions across multiple pits. This study presents a comprehensive approach to optimize blasting practices at Mont-Wright mine, tailored to the specific lithological characteristics of each rock domain. Through systematic analysis and experimentation, blasting guidelines were meticulously developed, aiming to enhance grindability and equipment productivity. The implementation of these guidelines promises significant improvements in operational efficiency and resource utilization, positioning Mont-Wright mine at the forefront of sustainable iron-ore extraction.

Jan 21, 2025

By P. Coulombe, J-F. Riverin, A. Gaboury

Cavity cleaning during anode change generates a material that consists of anode cover material and cryolite melts. This material is scooped and placed in bins for transport and further processing and recycling as fresh anode cover material. Typical processing methods in use involve cooling of the hot cavity bath in bins, with or without emission treatment systems, until it is adequate to be processed and grinded to the required particle size distribution. Handling of the hot and cooled cavity bath material can be labour intensive. It also generates significant air emissions which contain particulate and gaseous fluorides. With the advent of the Aluminerie Alouette smelter Phase II expansion, the hot cavity bath tonnage to be processed increased to 700 t/day and maintaining existing practices was not satisfactory. This article presents a novel process implemented at the Alouette smelter where cavity bath is processed as a hot material directly from the potlines ( 600-800°C range), sized, cooled and then processed in the existing cold bath treatment plant. The system is designed to process 36 t/h, is fully automated and requires limited monitoring from operations. Implementing this new system in a Browrifield environment imposed numerous constraints for space, interfaces with existing operations, commissioning and ramp-up. It is presently operating at approximately 80% availability and is easily meeting the requirements of the potlines. This system has significantly improved the workplace environment in the bath treatment area and reduced the overall particulate and gaseous fluorides emissions at Alouette. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By C Parihar, R Garg, A Bhandari, S Bhandari

Blasting can impact the efficiency of entire downstream mining operation. Individual technology solutions for blasting have been available in the industry for many years but all of them only cater for certain aspects of blasting. Many of them are based on individual research and/or experiences. Some of the available software solutions are not suitable to be used in the field as that they need advanced skills or tools. Also, most do not take technology advancements like mobility, advanced data analytics, web solutions and integration into consideration. Hence, no technology platform is currently present in the industry that addresses all potential needs a blaster may need in an integrated manner.This paper presents an integrated solution that takes care of all aspects of blasting – design blasts according to mine plan; collect data after drilling has been carried out (as there is often difference in designed and actual drilled hole locations in the field); predict blast results in terms of fragmentation, flyrock, ground and air vibrations, wave front reinforcement and flyrock distance; and after assessment, allows changes in charging, delay timing and sequence. The technology solution is a secure, cloud-hosted, web-based software-as-a-service solution that can be accessed from anywhere. Also it has a mobile app, which is available for both Android and iPhone/iPad. The mobile app is also integrated with the web-based solution using application programming interface calls to the central data repository.Case studies for two limestone mines are presented where this solution is being used in its initial format. This software platform enabled analysis of the outcome from a previous blast pattern and then subsequently allowed optimisation of blasting operations based on historical data. Uses of this platform have resulted in improved key performance indicators in these two limestone mines. The mobile app as part of this platform enables extensive field blast data capture and analysis and also various predictions before a blast. Data collected include blast parameters, individual hole charging, initiation pattern, videos, photographs and vibration records for analysis/reporting. The key features of the solution are a blast designer, a detailed blast data collection/analysis and a series of environmental predictors. These predictors give blast results in terms of fragmentation, flyrock, ground and air vibrations and wave front reinforcement and take remedial steps before blasting to optimise and control adverse environmental impact. Many features, such as fragmentation predictor and mobility solution, are completely unique features that are not available elsewhere in such a field personnel-friendly manner.CITATION:Bhandari, S, Parihar, C, Garg, R and Bhandari, A, 2015. An integrated technology solution for optimised and environmentally-controlled blasts, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 393–400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Perry D. Teitelbaum

In two earlier studies the Federal Bureau of Mines undertook to explore comprehensively the dimensions of the Nation's energy balance. The first of these studies, published in 1950 as Bureau of Mines Information Circular 7582, by Harold J, Barnett, was primarily concerned with projections of future domestic energy requirements and supplies, because these related to projected growth in major fuel-consuming sectors of the economy, changing rates of energy-use efficiency, and interfuel substitution patterns. But, to provide the essential background for these projections, it was first necessary to assemble and examine in some detail the quantitative information on the size and shape of the current United States fuel economy. Among other things, Barnett's path-breaking study indicated the need to consider energy as an entity, particularly for public and private policy makers, industry and commodity analysts, economists, and others concerned with long range questions of domestic and international energy supply and demand. The study also spotlighted a gap in the fabric of current economic intelligence; no comprehensive collation and reconcilation in any single report of available published statistical information covering the origin -a disposition of all energy materials existed. In response to this latter need, the Bureau of Mines prepared the second of the two studies referred t3 above. This was published in 1951 as Report of Investigations 4805, by W, H, Lyon and D, S. Colby, and it consisted of statistical information on the production and use of each of the various fuels and electric energy in the United States for 1929, 1939, and 1947; all were presented in tabular form and on a uniform basis. The three years selected were chosen largely on the basis of data availability.

Jan 1, 1961

By D. E. M. Plaumann, B. S. Fee, R. D. Hansen, R. R. Klimpel

"This paper briefly summaries the status of a recent program aimed at identifying new chemistry for use as sulfide mineral frothers and collectors. The background motivation and planning behind this work is given along with the general families of chemical structures synthesied and studied in detail followed by typical flotation application results in various laboratory and plant scale tests. Flotation testing to date has been very encouraging with often improved recoveries of certain minerals and improved pyrite selectivity being observed over commercially available reagents. In addition, in some cases, the dosage and lime requirements of these new collectors are significantly less than that associated with standard sulfide mineral collectors. INTRODUCTIONFroth flotation is one of the most widely used and economic means of concentrating metal sulfide ores. There are numerous reference books that have been published on the chemical aspects of flotation [e.g., ref. 1-7] which are based on studying the influence on selected minerals of chemical structures that have been used commercially for many years. In fact, almost 98% of the volume of flotation collector and frother reagents used at the industrial level today were known and manufactured in some form 25 years ago [8]. There are many reasons for this lack of significant new flotation reagent development [9] including the general utility and relative cheapness of existing collectors such as xanthates and existing frothers such as the alcohols and glycol ethers. Another reason is the inherent complexity of the flotation process itself coupled with highly variable and difficult to standardize feed materials. This environment makes reliable reagent comparisons difficult and seriously limits the use of theoretically based chemical structure studies to predict new or optimal reagents. In addition, the higher cost of specialty flotation reagents demands that their performance attributes be significantly greater than that achieved with existing all-purpose commercial reagents - something often difficult to prove in practice."

Jan 1, 1988

By S Ellis, J McMullen, M Habner

A new leaching regime was implemented at Kalgoorlie Consolidated Gold MinesÆ (KCGM) Gidji plant on a cyanide leach of ultra-fine ground sulfide concentrate. High lime concentration and lead nitrate were used to overcome the refractoriness of the fine sulfides (high reactivity of fine sulfides with the presence of gold tellurides). The leach pretreatment stage was shown to be detrimental and was shut down. Lime titration was introduced as part of the process control. It was shown that the leach could be performed at low dissolved oxygen, (ie 3 - 5 ppm) to avoid sulfide oxidation and the associated high cyanide and lime consumption. Plant results showed reduced cyanide consumption (40 per cent) and an accelerated leaching rate, whereby most of the gold was dissolved in 24 hours compared to 72 hours used previously. Similar work was performed at KCGMÆs Fimiston plant, which leached a combined ultra-fine ground sulfide concentrate along with the slimes fraction from hydrocycloning the bulk flotation concentrate. The use of lead nitrate, high lime and carbon-in-leach generated a faster leaching rate and minimised adsorption of gold on fine pyrite particles. The grind, previously controlled with a P80, was replaced by a P98 to give a better operational indication of top size hydrocyclone performance. Before the implementation of the changes, average leach residues for slimes and UFG were respectively 4.0 g/t and 5.5 g/t. With the modifications to the leaching regime, average leach residues were lower by 1.5 - 2.0 g/t. Whilst significant improvements have been demonstrated, further work is progressing at KCGM to further reduce ultra-fine concentrate leach tail grades, and also to improve the understanding of concentrate refractoriness and the factors responsible for differences between laboratory and plant leach results. Estimated profits since the implementation of the new approach are in the range of $A3.5 million per year.

Jan 1, 2005

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By S. Yuan

A large-scale work scheduling algorithm has been developed in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. This study basically concerned the formulation of a reliable mathematical programming model to handle the problem, the achievement of an efficient solution of the model, and the implementation of the algorithm to the worker assignment problems of a large underground coal mine. The results showed that the work scheduling algorithm can make optimal assignments efficiently. It is believed it has potential significance in improving manpower utilization and can offer great help to coal mine managers in making efficient manpower allocations.

Jan 1, 1994

By D H MACKENZIE

In common with several great orebodies and mineral camps around the world Broken Hill has been the subject of state-of-the-art technical and scientific scrutiny during its long working life. During the early years geological interest in Broken Hill tended to be directed at the body for its intrinsic scientific worth, mainly on account of its large size, high grade and wealth of mineral species. For much of the last 60 years the interest has had a more applied motivation, namely, to assist the search for either repetitions in the Broken Hill field or analogues in other terrains. This paper looks at the major changes in geological concepts and exploration techniques applied at Broken Hill and attempts to assess their impact.

Jan 1, 1992

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining CO.'s Granite Mountain shaft. How this, insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the fire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest producer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By H. Hao

This paper outlines the development of a 2-D axisymmetric mathematical model to predict the evolution of temperature during the Direct Chill (DC) casting of AZ31 magnesium billets. Model predictions of temperature have been compared to measurements made on an industrial DC casting machine at Timminco Ltd, in Haley, Ontario. These measurements have been used to fine-tune the thermal boundary conditions employed in the mathematical model, The model, which is based on the commercial finite-element code ABAQUS, has been developed as part of a strategic project aimed at improving the DC casting process for light metals through a reduction in casting related defects and increased productivity.

Jan 1, 2004

By Z. Sample

"INTRODUCTION This past year commodity prices continued their dip with increased volatility causing market values to slide another 16% putting increased pressure on even the largest companies to improve their free cash flow.[1] Without a recovery in commodity prices in sight, companies must find a sustainable method to improve returns in the current economic climate. In an effort to improve plant sustainability, the mineral processing industry is investing in advanced automation technologies and innovative processing methods that are both more reliable and more efficient than ever before. One such breakthrough technology is Heap Leaching (HL). This method of extraction has certain advantages over traditional metallurgical methods making previously unsustainable operations economically feasible. While HL is already seeing use in the gold and copper industries among others, recent developments may allow for the use of HL to process primary sulfide ores which make up about 80% of today’s ores.[2] For this reason, this emerging technology is poised for exciting growth. Unfortunately, as with any process change, the implementation of HL projects requires significant training on both the control system as well as the underlying process, and further, due to the complex nature of the HL process, this can be a particularly difficult task. DEMOGRAPHIC TIME BOMB Even before the implementation of these new technologies, the availability of the skilled workforce has already become a significant problem for the mining and mineral processing industries. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years.[3] This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, research suggests that up to 50% of skilled mining and mineral process professionals are expected to retire in the next 5 years, leaving with their irreplaceable knowledge and experience.[4] While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences. In addition to a rapidly aging workforce and an inexperienced labor pool, a study done by the Oil and Gas Journal showed that it takes about 7 years, on average, for new workers to achieve a level of competency that permits them to assess risks and appropriately make decisions.[5] Not only is this figure is in direct conflict with the typical tenure of 5 years in one position meaning that the thinly spread skilled labor will be required to become senior staff before they are able to achieve competency in their current role, this also means that these millennials are not given the opportunity to become competent in their role before the retirement of the more experienced workforce."

Jan 1, 2016

By J. E. Rourke, O&apos

This report incorporates a review of available dewatering technology and an evaluation of its relevance to surface coal mines in the Interior Province of the United States. Guidelines for the selection, design and construction of dewatering systems are included. On the basis of documented experience, candidate dewatering systems were selected and evaluated with respect to their anticipated impact on the environment and mine operations. Included in the discussion is a summary of laws and regulations which can impact on dewatering operations. Following this discussion, geologic and hydrogeologic conditions within the Interior Province are described and potential dewatering problems at surface coal mines are identified. Model mines are developed which exhibit the most difficult dewatering problems identified, and it is demonstrated how available technology can be utilized to deal with these problems. Dewatering of coarse-grained, high permeability terrace deposits might be economically feasible today. Low permeability, saturated glacial tills or lake deposits appear to be significantly outside present economic feasibility for dewatering.

Jan 1, 1979

By G. H. Blackwell

Sequences in open pit mining must be planned and regularly revised to incorporate changes in the variables which affect profitability. Interactive computer planning with colour graphic facilities is an effective tool for this purpose in the short and medium term. An interactive computer planning system for medium-size, low grade porphyry copper-molybdenum open pits is described. The planning system proved especially valuable during the critical stages of pushback mining when deep, inner pit ore was nearly depleted and the erratic grades of the next pushback provided ore and marginal material at a time of depressed metal prices.

Jan 8, 1993