Search Documents

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996

By K. H. E. Kroemer

Selecting persons who are unlikely to suffer an overexertion injury is one of three methods to reduce the risk of musculo-skeletal disorders in manual material handling. This paper describes the underlying models, methods, and techniques for such personnel selection. In particular, it describes the isoinertial LIFTEST in which persons actually lift weights to assess their capability for doing so on the job.

Jan 1, 1985

By J. M. Bowen, P. Wemyss

"Gold losses to natural carbonaceous matter during cyanide leaching have been investigated for over a century. The variation in the severity of the problem from one ore to another has led to a range of different processes being implemented at different mine sites. Most commercial options utilise one or more of the following processes: roasting, carbon pre-flotation, organic blinding, CIL, chlorine passivation, pressure oxidation, biological passivation, elevated temperature CIL, RIL and thiosulfate. This paper provides a background to identify the most appropriate process or combination of processes for a particular ore. It also presents information on how these processes may be implemented, drawing on information in the literature and from current or recent applications at operations such as the following: Stawell, Kumtor, Penjom, Twin Creeks, Macraes Flat, Kittilä, Fosterville, Inata, Carlin, Goldstrike, and Jerritt Canyon. Various process options have been dismissed, or deemed unsuccessful due to limited knowledge available on the strengths and weaknesses of the different options and their implementation. The authors have collectively been involved in flowsheet development and project implementation in four commercial plants that have treated preg-robbing ores.INTRODUCTION Cyanide processing has been the mainstay of gold recovery for well over a century. It is generally a very effective process with over 90% recovery on free milling ores, but complex and refractory ores may only give 0–50% recovery with conventional processing (La Brooy et al., 1994). People have written about gold losses to natural carbonaceous matter during cyanidation for over a century e.g. Feldtmann, (1915). The earliest reports related to African operations, but the issue has since been reported in Canada, North and South America, Australia, Russia and China. The phenomenon is usually referred to as ‘preg-robbing’ dating from the times before the use of granular activated carbon for gold recovery, when gold was lost from the pregnant solution before it could be separated from the leach solids and recovered by cementation. Many excellent reviews have been published e.g. Dunn et al. (2013), summarising the options considered and where they have been applied commercially."

Jan 1, 2017

By M Scoble, W S. Dunbar

This paper reviews methods for grade estimation in short-term mine planning for block caving. Two particular tools are used: Ordinary Kriging and Simple Kriging with moving averages. It is also considered the influence of draw characteristics on the grade estimation process. Reference is made to mine case study data and analysis. These demonstrate that operational grade estimation is not a trivial process. It must take into consideration: the grade variability (in terms of ore and dilution), sampling interval, geological and geotechnical characteristics, geometrical layout and draw characteristics. Significant improvements appear possible in short-term planning if variogram analysis, as well as kriging methodologies, are introduced into the operational grade estimation process.

Jan 1, 2000

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Saturn light that significantly improves illumination for roof-bolting machine operators while reducing glare. The existing roof-bolter lighting was the baseline and was compared to the Saturn at 100, 75 and 50 percent intensities. Discomfort glare and disability glare were measured by the De Boer rating scale and the Mars Letter Contrast sensitivity test, respectively. Thirty study participants were tested. Discomfort glare was reduced at least three levels with the Saturn luminaire. Visibility levels were four to 6.5 times better with the Saturn than with the baseline. The Saturn design is freely available for commercialization.

By S. Leong

This paper reports on research examining disclosures from mining companies regarding their water usage in the Macquarie and Lachlan catchment areas, both parts of the Murray-Darling Basin in New South Wales, Australia. The objective of the research was to assess whether this disclosure is sufficient to allow communities to determine whether mining companies are complying with mining conditions of consent and abiding by the requirements of their water licencing agreements. These requirements are then compared to the water reporting requirements of the Global Reporting Initiative (GRI) and the Water Accounting Framework for the Minerals Industry (WAFMI). Communities are concerned about whether the mining industry?s use of water will have impacts on their livelihoods and lifestyle and thus require information concerning the quantity of water that will be extracted, how much water will be left for other stakeholders and whether the mining will affect water quality. This is an archival study. It has involved examining relevant publically available information released by mining companies and government regulators and determining if this is sufficient to meet the needs of the local communities. Additionally, it has involved looking at information indirectly provided by mining companies, via the use of intermediaries. Further, information availability concerning basic water accounting and regulatory breeches and whether such information is available at the mine site level has been considered. It is found that while NSW legislation places very little reporting requirements on mining companies, the development consent conditions for new projects and extensions to existing projects are quite significant and should be sufficient to meet the needs of local catchment residents though such information is not always easily accessible for the layperson.

Aug 1, 2013

Central to any business is its Asset Management Plan which encapsulates the business context and key organisational objectives such as profitability, safety and environmental standards. Life Cycle Planning (LCP) is a key component of an overall Asset Management Plan. A comprehensive approach to Life Cycle Planning forecasts the financial expenditure required to support the performance of the asset over the business life. It incorporates capital, maintenance and operational expenditure along with an estimation of economic life. Within its body the LCP provides the detail of the maintenance plan and method of its execution. Once optimised the LCP becomes the overarching plan executed through the application of several elements of the Asset Management Plan to ensure the return on investment from the assets is optimal. Each of the elements of the LCP is bound by a set of loops that provide information based on the analysis of outcomes. These loops drive the continuous improvement of performance and cost over the life of the asset. In this way we ensure that the LCP is a dynamic plan responsive to the changing business environment. The paper being presented today will describe the process undertaken and the outcomes derived when this approach was applied to a $600 M+ coal handling and preparation plant in QueenslandÆs Bowen Basin. It will also delve into the difficulties encountered from both technical and cultural aspects; the latter proving to be the most difficult to manage. It will describe the hurdles and barriers that hampered progress including the human influences and the natural desire to revert to what has been done in the past when things became a bit difficult. In the end the results are there to show that the upfront expenditure and investment in time was time and money well spent and the outcome has the operation well placed to manage the assets in a manner designed to deliver the optimal business outcome.

Jan 1, 2007

By W. A. Jacob, E. W. Dean

The Pittsburgh petroleum laboratory of the Bureau of lines has recently developed an improved method for the determination of water in pctroleum emulsions. It has been described in detail in an article entitled "A convenient method for the determination of water in petroloum and other organic emulsions" by E. W. Dean and D. D. Stark (Jour. Ind., and Enc. Chem. Vol. 12, ſay, 1920, page 436). It is essentially a modification of the familiar procedure of "distillation with an iniscible solvent", the improvement consisting in the use of apparatus that is rºck more convenient than any previously employed. The method has been used with marked success in the Bureau's laboratories for a period of about a year and has also been tried with equal satisfaction by a number of other laboratories. It has been most extensively employed for determining the water content of heavy fuel oils but has been applied also to several other types of emulsions, including shale oils, tars derived from coal, greases, and mixtures of powdered coal, oil and water. The Bureau has received a number of requests for information regarding commercial sources for the apparatus used, and having been assured of the value of the method, has taken steps to render it available for general use. - The equipment is, with the exception of two items, made of parts that are obtainable from the ordinary stock of chemical supply houses. The two exceptions are (1) the so-called "distilling tube receiver" and (2) the electric heater. The former is an essential part of the equipment; the latter is a convenient ac cessory but it can if necessary be roplaced by a gas burner. Efforts on the part of the Bureau staff to ronder these two items of apparatus available for purchase from supply houses, or for production by the user are hero described.

Sep 1, 1920

By SangHyeok Han

Selecting the best possible cranes and identifying spatial conflict-free locations on sites can result in productivity and safety improvements for large-scale industrial construction projects. In the current practice, experienced lift engineers select cranes based on the heaviest lift and/or the largest lifting radius of the identified crane. This practice is relatively time-consuming, and optimization of the crane?s use and location is also difficult. There are many factors which need to be considered during the crane selection process, a reality which further complicates the process. This paper presents a framework which aims at developing a decision support system to enhance the crane selection process and collision-free path planning for large-scale construction projects. This paper utilizes an innovative crane selection matrix in order to establish a process for optimized crane selection for construction projects. The study considers more than 40 different factors in order to reduce time and improve safety for crane operations. Following finalization of crane type (mobile crane versus tower crane), a visualization model to simulate crane operation and identify collision-free crane operation paths is proposed. This process can assist project managers to plan the lifting process more effectively and efficiently. A case study-based approach was utilized to demonstrate the proposed methodology. The methodology was tested in the planning and construction process for boiler house structures in Mannheim, Germany. The project entailed numerous challenges: one of the major tasks was to lift a 102-ton load on the top of the boiler structure through crane collaboration; space limitations on site also presented several challenges related to crane selection, location, and operation processes. Based on the project constraints, the proposed crane selection framework, and the visualization models, two tower cranes were selected and successfully implemented in the case study.

Aug 1, 2013

"INTRODUCTION These inspection standards have been prepared for use as a guide for the Federal inspection of anthracite mines. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7231 in January 1943 and used as a guide for Federal inspections. Numerous changes in the original standards have been made, due in part to recognition of shortages of some types of safety equipment due to the war, in part to need of additional standards to cover certain mine conditions and practices, and in part to conditions not foreseen when the original standards were prepared.Throughout these standards reference is made to determining the methane content of the mine air by using a permissible flame safety lamp. The Bureau has approved various electrical devices for the detection of methane, but it is recognized that new devices for determining the percentage of combustible gases as well as the percentage of oxygen, might be perfected for general use in mines, and therefore it may be necessary to revise certain standards to include the use of such equipment if and when the device is accepted as being permissible.About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however, failure to carry out the suggestions made in such of the other standards as are applicable may also lead to loss of life.With continuing change in mining methods, some of these standards may become inapplicable, and further revision will be advisable. Therefore, question regarding these standards and suggestions regarding new standards should be brought to the attention of the Bureau, so that changes may be made from time to time. Numerous changes proposed by mine operators and by State mining departments have been incorporated in these standards."

May 1, 1944

By Steven R. Ahlfield, Ali Ghandeharioon

A wastewater treatment plant commissioned in 1978 is undergoing a major expansion. Planning various phases of the 8-hectare expansion at this site requires an understanding of the site response during and after construction, and the potential impact on adjacent properties and infrastructure. The expansion project requires nominally 5 m of site grading fill for flood protection. The site is underlain by loose to compact fine sand over firm to very stiff clay stratum that extends to great depths. Ground improvement is required to mitigate the liquefaction hazard in the fine sand stratum, and preloading is proposed to reduce post- construction settlements in the deep clay. Site development and foundation systems for the plant expansion project were evaluated by conducting settlement analyses which accounted for the historic and future site loading and 3-D modeling of soil layers with interpolation between borehole and cone penetration test (CPT) locations. The numerical model was calibrated to match short-term and long-term settlements measured at the plant site. The analyses were carried out to assess the effects of past loading, proposed preload and surcharge heights, lateral extents and durations as well as vibro-replacement ground improvement on post-construction settlements. Two design options were considered for the preload footprint across the site and foundation system for proposed facilities. It is shown that limiting the preload extent and founding some of the proposed structures on deep friction piles reduce the predicted settlements of adjacent infrastructure and result in reasonable performance for the proposed facilities. INTRODUCTION A wastewater treatment plant commissioned in 1978 will be replaced with a new plant on an undeveloped portion of the site to provide wastewater treatment for an expanded service area. The existing facilities must remain in operation until completion of the new plant. The site grade will be raised nominally 5 m for flood protection. The large areal extent of the site grading fill and plant structures will cause stress changes extending to great depths in the underlying soils and result in settlement of the existing and new structures. Historic settlement of the existing facilities has been tolerable for plant operations, but no settlement performance data was recorded during site development and post-construction from 1978 to 2007. Development of the 8-hectare expansion at this site is planned in three phases to reduce the overall construction schedule. Planning for each phase requires evaluating the effects of various site development activities from start to completion of expansion and during the design life (i.e. post-construction period), and the potential impact on existing wastewater treatment facilities and adjacent properties and infrastructure including an adjacent viaduct structure. Figure 1 presents the site plan and three distinct site development phases considered for the plant expansion.

Jan 1, 2019

By D. Warkentin, M. Tomlinson, A. Nacu

"This study focuses on comparing the “blinding” effectiveness of various organic additives as part of a general review of using organic additives to mitigate preg-robbing and improve gold recovery during cyanide leaching of carbonaceous gold ores. The laboratory results compared the impact of various organic additives on the prevention of gold adsorption using both activated carbon and ore samples containing carbonaceous matter, generally referred to as total carbonaceous matter (TCM). Although several organic reagents were found to have a significant blinding effect on activated carbon, these results did not translate into increased gold leaching efficiencies with actual ore samples.INTRODUCTION Preg-robbing refractory ores, which contain carbonaceous matter, have been problematic in cyanide plants for many years. In industry, preg-robbing by carbonaceous matter may be mitigated using various techniques including flotation, to remove the carbonaceous matter; addition of blinding agents, to passivate the carbon surface and prevent adsorption of gold cyanide complex; roasting, to partially or fully destroy the carbonaceous matter; chemical oxidation (Abotsi & Osseo-Asare, 1986); pressure oxidation; or microbial deactivation (Dunne, Staunton, & Afewu, 2013). Carbon-in-Leach and Resin-in-Leach are also used as process alternatives in which activated carbon or resins are used to compete with the carbonaceous matter for gold cyanide adsorption. For highly preg-robbing ores, thiosulphate leaching may be considered as an alternative to conventional cyanide chemistry (Baláz, et al., 2000). Natural carbonaceous matter is composed mainly of hydrocarbons, organic acids, and graphitic/amorphous elemental carbon. Natural elemental carbon that behaves as activated carbon is considered to be the main reason for preg-robbing, although the true nature of this phenomenon is not fully understood (Tan, Feng, Lukey, & van Deventer, 2005). In general, the hydrocarbon fraction is assumed to have negligible interaction with gold, while organic acids, such as humic acids, may form complexes with gold, inhibiting its extraction in cyanide solutions. Organic reagents have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Abotsi & Osseo-Asare (1987) tested various organic compounds, with two possible effects in mind. First, the organic compounds were expected to adsorb onto the surface of the solids as anionic/cationic species; the resulting electrostatic interactions between the Au(CN)2- anion and the negatively/positively charged surface would inhibit/enhance the gold uptake. Second, the organic reagents were expected to coat the surface of the carbonaceous component in the ore, limiting the available adsorption sites and reducing gold losses. Optimal reagent dosage depends on ore mineralogy, maturity and surface area of the carbo"

Jan 1, 2019

By William A. Hustrulid

A technical and economic evaluation of the potential for improving mining productivity through the use of underreamers in blastholes, specifically in relation to Minnesota taconite, Arizona surface copper and in situ mining operations is presented. Included are (1) a review of the drilling and blasting practices presently being used, (2) a discussion of current underreamer technology. (3) the presentation of a general economic cost model for underreaming, (4) the application of the model to surface taconite, surface copper and in situ mining, and (5) a summary discussion including required performance specifications, potential overall benefits, and recommendations for further development.

Jan 1, 1977

By John L. Kaplin

The underground construction for the Phase I Combined Sewer Overflow(CSO) Project is on an impressive scale by any measure, appearing more so in a midsize city like Providence, RI. The Narragansett Bay Commission recently completed $350 mil-lion in construction to improve the water quality in Narragansett Bay. This project included a number of serious challenges, delays, and disputes. Looking back on this complex project completed within budget, it is hard to consider the work as anything other than a success. Along the way, this outcome did not always appear certain.

By D Baas, D Bennett

This paper describes how Brisbane-based PanAust Limited develops process control strategies that are implemented at all operations and are used in functional descriptions for plant upgrades and new projects.The process control strategies are determined by operating management philosophies designed to maximise returns from the company’s assets.The approach is endorsed in the project planning and design phases to ensure facilities and equipment that form the major production assets are fit for purpose and capable of enabling the production managers and operators of the projects to maximise shareholder returns.PanAust’s process control approach has been to develop sets of process control standards which focus on two key areas. The first area covers hardware requirements and architecture, software objectives, control models and individual loop tuning methods. The second area defines control room layout, graphic standards and the alarm philosophy. The application of these standards in a new plant or upgrade decreases the time required to achieve design capacity and optimal performance.The PanAust process control strategy changes the operator’s role from one that controls a number of individual loops to one that sets the control objectives of the processing plant. To achieve optimal performance, all the process areas of the plant are analysed to identify opportunities to improve throughput, recovery and stability. Once a key opportunity is identified, a process control strategy is developed which defines the objective of the control, its functionality and how an operator will interact with it. After development of the control model the operators assist engineers to test and debug it. Once the model is robust, it can then be duplicated throughout the group and developed as a group process control standard.CITATION:Baas, D, Bennett, D and Walker, P, 2014. Developing process control standards for optimal plant performance at PanAust Limited, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 325–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Vathsala Rajagopal, lwao lwasaki

The grinding media materials for the mining industry require corrosion and abrasion resistance properties not only to minimize the wear but also to improve the flotation recoveries of sulfide minerals. The media wear mechanisms and the factors influencing the grinding ball wear during grinding are discussed with respect to abrasion, corrosion and impact wear of grinding media materials. Interactions between the grinding media and sulfide minerals in a ball mill adversely affect the floatabilities of the ground minerals. The possible galvanic interactions between grinding medium-mineral and their effects on the flotation responses of sulfides are also reviewed. The selection criteria for alloy composition that reduces the overall wear along with adverse effects on flotation are brought out.

Jan 1, 1992

By J. C. Johnson

The problem of estimating pillar capacity in coal mines has motivated development of a variety of empirical equations. Most of these equations have arisen from experience and a very limited set of measurements that have, necessarily, been focused on particular regions or coal fields. Their applicability is often limited to a specific range of pillar sizes. This is of particular concern in the design of large gateroad pillars and small barrier pillars between panels. The result has been a variety of equations and equation coefficients that can calculate load estimates to size pillars. Inclusion of these equations in more sophisticated loading models, such as boundary element methods (e.g. LaModel and MULSIM) has been hampered by absence of a function that describes specific variation of coal strength within the pillar. A singular exception, to our knowledge, is a function corresponding to the Bieniawski pillar strength equation. Because of this, it is the only coal strength criteria inherently available in most boundary element models. This paper presents a general method for deriving local coal strength, as a function of distance from the pillar rib, for an arbitrary pillar strength equation. Integration of this function provides the strength of pillar regions, or cells, needed for boundary element models. The method is demonstrated for the Bieniawski, Maleki and Holland-Gaddy equations. The Maleki and Holland-Gaddy equations contrast strongly with Bieniawski as strengths are extrapolated to large pillars and barriers. This development provides a tool for incorporating any of the proposed empirical equations into a boundary element model, thereby allowing the analyst to choose the most appropriate equation for a particular region, coal seam and/or pillar size.

Feb 23, 2014

By J. R. Thoenen

In Progress Rerort 1,4/ a number of facto were demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By Frank E. Chase

Retreat mining is one of the most hazardous operations conducted underground. One of the keys to miner safety and an efficient recovery of the reserves is to design adequately sized production pillars to prevent pillar squeezes, excessive pillar spalling, severe floor heave, roof falls, and pillar bumps. Currently, few pillar design approaches are available which consider the abutment pressures generated by the gob. The Bureau of Mines is developing a method called Analysis of Retreat Mining Pillar Stability (ARMPS) to aid in the design of retreating sections. Back analysis of 42 case studies indicates that ARMPS can be helpful in predicting stability during retreat mining operations.

Jan 1, 1993

By F. K. McKean

Abstract A discussion of the difficulties involved in the production of a clean molybdenite concentrate introduces the paper. There is a brief description of the various methods for producing molybdenite that will fit marketing specifications, and it is shown how these methods are nor suited to the milling of ores containing small quantities of bismuth and copper. A process that was developed in the ore testing laboratories of the Bureau of Mines at Ottawa for the La Corne mill of the Molybdenite Corporation of Canada is described in derail and some results from pilot plant operation of this milling scheme are tabulated. A description of the La Corne mill, where the writer supervised the introduction of the process on a commercial scale, adds to the interest of the paper. In conclusion, there is a review of the conditions necessary for proper operation of the flowsheet. An attempt is made to show how the process might be satisfactory in other problems similar to that at the La Corne mill. Introduction The production of a molybdenite concentrate, free from impurities and high in grade, has been a difficult task when milling some types of ore. Whereas ordinary flotation techniques will produce acceptable concentrates of the baser sulphides, in many cases they will not serve in the treatment of molybdenite, for this mineral must be of optimum grade and purity to bring the best prices, or to find a market at all . Faced with the necessity of meeting stringent specifications, the mill operator has been forced to employ expensive processing methods, and to be satisfied with low recoveries, in order to make grade with his product. The most objectionable and common impurities found with molybdenite are: (a) gangue minerals and iron sulphides, which lower the grade; and (b) copper, bismuth, or antimony, which are deleterious in the final uses of the molybdenite products. It is difficult, and sometimes impossible, to market a concentrate with over 0.5 per cent of any of the latter impurities, or with a grade much below 90 per cent MoS2. Various methods, which have been highly successful in specific applications, have been developed to meet the problem of producing a suitable concentrate. All of them, however, have certain defects precluding their use when treating ores of a nature different from the one for which they ? were designed. The writer has developed a process for molybdenite ores having an objectionable impurity content. A description of the procedure involved, and of the La Corne mill of the Molybdenite Corporation of Canada, where the process has been adopted, should be of interest to flotation operators.

Jan 1, 1947